Shure orporated UT1D Belt Worn Wireless Microphone User Manual 27a8692

Shure Incorporated Belt Worn Wireless Microphone 27a8692

Manual

ENGLISHTHE TWO MINUTE USER’S GUIDE2:00The instructions on this page will help you get your UT Series system up andrunning in minutes. For more detailed instructions, read the section of thismanual that applies to your system.RECEIVER SETUP1. Connect the supplied ac power adapter to the DC INPUT connector on the back ofthe receiver. Insert the adapter’s cable into the power cable retainer on the bottomof the unit. Plug the adapter into a wall socket or other electrical outlet. The greenPOWER light on the receiver will glow.2. If you are using The Guitarist-UHF, connect the receiver output to a guitar am-plifier using any standard guitar cable. If you are using The Vocal Artist-UHF,The Headset-UHF, or The Presenter-UHF, connect the receiver output to anaudio mixer using an XLR to XLR audio cable.3. Raise the antennas and point away from each other at a 45° angle from vertical.TRANSMITTER SETUP1. Open the transmitter battery compartment and install a 9 V battery. Observe properbattery polarity (“+/–”).2. If you are using The Vocal Artist-UHF, no further transmitter setup is required.3. If you are using a body-pack transmitter (The Presenter-UHF, The Headset-UHFor The Guitarist-UHF), plug the microphone cable or a WA302 instrument cableinto the four-pin connector on the transmitter (if using The Headset-UHF, see tagon headset for assembly instructions). If using The Guitarist-UHF, plug the instru-ment cable into the guitar output and adjust the volume control of the guitar.OPERATING THE SYSTEM1. Slide the transmitter POWER/OFF switch to the POWER position. The transmitter’sgreen POWER light and the receiver’s yellow DIVERSITY A/B lights will glow.2. Slide the MUTE/ON switch on the body-pack or hand-held transmitter to the ONposition.3. Talk or sing into the microphone, or play your guitar. The receiver’s red AUDIO PEAKlight should flicker when loud sounds are transmitted. If the AUDIO PEAK light doesnot flicker or stays on constantly, the transmitter gain may need adjustment. (Referto the Transmitter Audio Gain Adjustment section). NOTE: This step is particularlyimportant for The Guitarist system, since guitar outputs can vary widely.4. Adjust the receiver VOLUME control until the receiver output level matches thelevel of your guitar or microphone through a cable. (The factory setting is in thefull clockwise position.) If using The Guitarist-UHF system, see Receiver VolumeAdjustment for The Guitarist-UHF to match the receiver volume level to the levelof a wired system.YOU ARE NOW READY TO PERFORM!IMPORTANT: Every wireless performance is a unique situation, and can present a vari-ety of problems. Never attempt a performance without first conducting a “walkthrough”test on the wireless system in the performing area. If you encounter a problem, refer tothe Troubleshooting table.2
ENGLISHTHANK YOU FOR CHOOSING SHURECongratulations! You have purchased the finest wireless system in itsclass. Your Shure wireless system is engineered to provide a low-noise,high-quality sound comparable to other systems costing much more. Builtin the tradition of reliability that has made Shure a symbol of American quali-ty for more than half a century, this wireless system should provide you withexcellent performance for years.To get the most out of your UT Series wireless system, please read theapplicable section in this guide before you attempt to use the system. If youhave any questions that are not answered in this booklet, please contactShure Customer Service at (847) 866-2553, Monday through Friday, from8:00 am to 4:30 pm, Central Standard Time. For technical data by fax, dial(800)488-3297 and follow the recorded instructions. Visit our website atwww.shure.com for further information on this and other Shure products.INTRODUCTIONYour new UT Series system is designed to give you the best of both sound reinforce-ment worlds: the freedom of a wireless system, and the reliability of world-famousShure sound quality. This manual covers each of the UT Series systems: The VocalArtist-UHF, The Presenter-UHF, The Headset-UHF, and The Guitarist-UHF.SYSTEM FEATURESAll Shure UT Series systems offer a variety of of exceptional features, including:•Diversity Receivers with Exclusive Shure MARCAD Circuitry: MARCAD(MAximum Ratio Combining Audio Diversity) circuitry continuously processesthe rf signal from each antenna and combines the audio outputs to produce onesignal of optimum quality. The result is improved reception and exceptional free-dom from dropouts.•Low-Traffic UHF Transmission: UT systems use a UHF (Ultra High Frequen-cy) range between approximately 596 to 862 MHz (available frequencies de-pend on regulations in the country where the system is used). In urban areas,UHF frequencies are less congested than those in the VHF range, and are lesssusceptible to interference.•Multiple System Use: Up to eight UT systems can be used in the same perfor-mance space. Each system must be set at a different frequency. If systems areset to the same frequency, contact an authorized Shure dealer. NOTE: In multi-ple use situations, each transmitter must have a dedicated receiver.•Simultaneous Output Use: Unbalanced 1/4” phone plug and balanced XLRoutput connectors may be used simultaneously to different external devices.•Stackable and Rack-Mountable Receivers: If multiple systems are in use, re-ceivers may either be stacked or rack-mounted, with two receivers fitting in theoptional rack mount tray. In these situations, antennas should not touch or becrossed. (See Stacking and Rack-mounting Receivers.)•Range: UT Series transmitters will work at a distance of up to 100 meters (about300 ft.) from the receiver.•Noise Squelch: The noise squelch circuit analyzes signal quality instead of sig-nal strength, which allows the circuit to discriminate between noise and desiredsignal. This reduces the likelihood of noise burst due to environmental rf (radiofrequency) noise.•Semi-Rigid Receiver Antennas: Three-inch rubberized antennas offer perfor-mance equal to telescoping antennas with added durability.•Low Battery Warning Light: A red light on the body-pack and hand-held trans-mitters warns the user that there is less than one hour of battery life left.3
ENGLISHSYSTEM TYPESThe Vocal Artist-UHF is a hand-held system designed for singers who desire thehigh quality of Shure microphones and the freedom of wireless performance. In-cludes a Shure BG3.1 or SM58 dynamic microphone with a built-in transmitter.The Presenter-UHF is a body-pack system designed for public speakers who preferan inconspicuous, hands-free lavalier microphone. Features an omnidirectionalShure WL93, supercardioid WL184, or cardioid WL185 micro-miniature lavalier mi-crophone.The Headset-UHF is a body-pack system designed for users in physically active ap-plications, who desire the freedom of hands-free microphone operation along with theperformance of Shure wireless equipment. Features a WH20TQG headset microphone.The Guitarist-UHF is a body-pack system designed for use with electric guitars,basses, and other electric instruments. May be used with brass or woodwind instru-ments, with optional WM98 instrument microphone and mount. The Guitarist pro-vides the freedom of going wireless and the reliability of high quality Shure sound.SYSTEM COMPONENTSComponentThe Vocal Artist-UHF The Presenter-UHF The Headset-UHF The Guitarist-UHFTransmitter UT2 Hand-Held Micro-phone TransmitterUT1 Body-Pack TransmitterMicrophone* BG 3.1 or SM58Hand-Held Micro-phoneWL93, WL184 orWL185 LavalierMicrophoneWH20TQG HeadsetMicrophone —Receiver UT4 Diversity Receiver with MARCAD CircuitryPower Supply PS20 (120 Vac, 60 Hz) or PS20E (230 Vac, 50 Hz)SuppliedAccessoriesMicrophone StandAdapter, Vinyl Trans-mitter Bag,Receiver Feet,Receiver VELCROMounting StripsVinyl Transmitter Bag,Receiver Feet,Receiver VELCROMounting StripsVinyl Transmitter Bag,Receiver Feet,Receiver VELCROMounting StripsVinyl Transmitter Bag,Receiver Feet,Receiver VELCROMounting Strips*Additional microphones may be available at later dateSTACKING AND RACK-MOUNTING RECEIVERSSHURESHURESTACKED RECEIVERSSHURE SHURERACK-MOUNTED RECEIVERSFIGURE 1The UT4 receiver may be used in numerous applications, and is designed to be easi-ly stacked or rack-mounted for multiple system use (see Figure 1).•To stack receivers: The raised corners are designed to create stability when receiv-ers are stacked, if placed on a flat surface with feet attached. It is important to posi-tion the antennas at a 45° angle from vertical so that the antennas do not touch.•To rack-mount receivers: The UT4 receiver is a half-rack unit, and two receiversshould fit into a standard rack space. Place the outer antennas at a 45°angle fromvertical; place the inner antennas in a vertical position. ANTENNAS SHOULD NOTCROSS OR TOUCH. (See Optional Accessories for rack mount accessories.)4
ENGLISH6710911123458SHURE BOTHERS INC. EVANSTON IL 60202 USAUT4 DIVERSTIY RECEIVER12–18 VDCDC INPUTUNBALANCEDHIGH ZBALANCEDLOW ZLINE MICSQUELCHMIN MAXFIGURE 2...........UT4 DIVERSITY RECEIVER FEATURES (FIGURE 2)1. Power On Indicator: This green light glows when the receiver is plugged into anelectrical outlet. It indicates that the receiver is on.2. Diversity Signal Indicators: The yellow DIVERSITY A/B lights glow when rf (radiofrequency) signals are received from the UT1 or UT2 transmitter. When only one lightis glowing, the signal is being received on only one antenna. When both lights areglowing, the UT4 is receiving signals on both antennas.3. Audio Peak Indicator: This red light flickers when the receiver input signal ap-proaches the overload clipping level. It is affected by the transmitter gain control set-ting, and the level of the guitar or bass (The Guitarist-UHF systems) or the singer orthe speaker (The Vocal Artist-UHF, The Presenter-UHF, and The Headset-UHF sys-tems).4. Volume Control: Rotate this knob to increase or decrease the volume of the re-ceiver output. This control does not affect the AUDIO PEAK indicator.5. Semi-Rigid Receiver Antennas: The semi-rigid receiver antennas should bepointed away from each other at 45° angle from vertical for best performance, andshould not touch when stacked or rack-mounted.6. 1/4” Phone Jack Audio Output Connector (Unbalanced High Z): An unbalancedaudio cable with a 1/4” phone plug (such as a standard guitar cable) can be usedbetween this connector and your amplifier input.7. XLR Audio Output Connector (Balanced Low Z): Plug an XLR audio cablefrom this connector to the input of your mixer.8. Mic/Line Slide Switch: Switches output of XLR connector from microphone toline level. Use of line level is suggested when connecting receiver to a mixing oramplifying device without an available mic-level input, such as a power amplifier,signal processing device or VCR.9. Squelch Control: Adjusts squelch control setting to emphasize either signal qualityor system range. This control is factory pre-set, and normally does not need furtheradjustment. Refer to Receiver Squelch Adjustment section for more information.10.Power Input Connector: Connect the ac adapter to this jack and then plug intoan ac electrical outlet.11. Power Cable Retainer: Secures the ac adapter cable to receiver. 5
ENGLISHFIGURE 31110ONMUTELOW BATTOFF PWR123456789INPUTATTEN0-20UT1 BODY-PACK TRANSMITTER FEATURES (FIGURE 3)1. Power/Off Switch: Turns transmitter power on and off.2. Input Attenuation Switch: Allows choice between 0 dB and –20 dB attenuation,for greater range of audio gain control.3. Power/Battery Fuel Gauge: The green light indicates the unit is on. The red lightindicates less than one hour of battery life remains.4. On/Mute Switch: Mutes the transmitter to prevent unwanted sounds from beingpicked up by the receiver without turning the transmitter off.5. Input Connector:Tini Q-G connector allows connection to a variety of lavalier andheadset microphone cables and the Shure WA302 instrument adapter cable.6. Belt Clip: Secures the transmitter to a belt, waistband or guitar strap.7. Audio Gain Control: Provides audio level adjustment to accommodate various inputsignal strengths (e.g., speaking into a microphone or playing an instrument). The fac-tory setting is at mid-point. A small screwdriver is supplied to make adjustments.8. Antenna: A flexible wire antenna is permanently attached to the bottom of theUT1 body-pack transmitter. For best operation, the antenna must hang vertically,and should not be coiled or bundled.9. Battery Compartment: Holds one 9 V battery. Hinged cover opens to provide ac-cess to the battery.10. Lavalier Microphone (WL93 shown): Omnidirectional (WL93), supercardioid(WL184) or cardioid (WL185) condenser lavalier microphone, featuring a mountthat clips onto a tie, lapel, or acoustic instrument and an attached TQG connector(supplied with The Presenter system)11. Headset Microphone (WH20TQG shown): Headset microphone features aheadset frame, headband, and an attached TQG connector. See tag attached toheadset for assembly instructions (supplied with The Headset System).6
ENGLISHATTACHING THE UT1 BODY-PACK TRANSMITTER TO BELT ORGUITAR STRAPFIGURE 41. Depress the tab marked PRESS and slip your belt, waist band or guitar strap be-tween the transmitter body and the belt clip (Figure 4).2. The clip holds tighter if the material is drawn to the clip’s top wire, especially whenusing thinner guitar straps.UT2 MICROPHONE-TRANSMITTER FEATURES (FIGURE 5)41765FIGURE 523FFOPWRLOW BATONMUTE1. Power/Off Switch: Turns the transmitter on and off. It is recessed to prevent itfrom being accidentally turned off.2. Power On Indicator: Green light glows when the POWER/OFF switch is in thePOWER position, as a reminder to turn the transmitter off when it is not in use.3. Low Battery Indicator: A red light glows when there is one hour or less of usefuloperating time, allowing battery to be changed before power is depleted.4. On/Mute Switch: Allows muting of the microphone audio, avoiding the “thump”noise that can occur when turning the transmitter on and off.5. Audio Gain Control: Allows the level of vocals to be matched with the transmit-ter for better performance.6. 9 V Battery (shown installed): Provides power to the microphone-transmitter.7. Battery Cover: Unscrews for access to the 9 V battery and gain control.7
ENGLISHTRANSMITTER BATTERY INSTALLATION1. Slide the transmitter POWER/OFF switch to the OFF position.2.Body-Pack: Press down on the OPEN side of the battery compartment cover,slide it back and flip it open, as shown in Figure 6A.3.Hand-Held: Unscrew the transmitter battery cover to expose the battery termi-nals, as shown in Figure 6B.+-FIGURE 6AB-+4. Insert a fresh 9 V battery into the battery compartment as shown in Figure 6.5. Replace battery cover.6. When the transmitter’s red LOW BATTERY light glows, you have 1 hour or lessof useful battery life remaining; change the battery at your first opportunity.IMPORTANT: 9 V Alkaline batteries are recommended. 9 V lithium batteries are op-tional. Carbon-zinc and zinc-chloride batteries will not provide adequate power andare not recommended. 8.4 V rechargeable NiCd batteries may be used, but are notrecommended due to minimal lifespan. See Battery Life in Specifications for furtherdetails on battery selection.INSTALLING AC ADAPTOR CORD INTO POWER CABLE RETAINERPOWER CABLE RETAINER(BOTTOM VIEW)AC POWER ADAPTER ANDABCFIGURE 71. Refer to Figure 7. Turn the receiver over and locate the power cable retainer. Pinchthe ac adaptor cord approximately 6 inches from the dc plug, forming a small loop(A). Hold the cord vertical to the retainer and lower the tip of loop into the curved por-tion of retainer.2. Keeping the cord vertical to the receiver, pull the cord under the tab towards frontof the receiver (B), then pull down, locking the cord into the retainer (C).8
ENGLISHOPERATING THE VOCAL ARTIST-UHF SYSTEM1. Refer to Figure 8. Connect the supplied ac power adapter into the DC INPUT con-nector in back of the receiver. Insert the adapter’s cable into the power cable retainer.Plug the adapter into a wall socket or other ac power source (use PS20 for 120 Vac,60 Hz power; use PS20E for 230 Vac, 50 Hz power). The green POWER light onthe receiver will glow.2. Connect the receiver’s XLR AUDIO OUTPUT connector to the mixer input using anXLR to XLR audio cable. If no XLR cable is available, a 1/4” to 1/4” phone plug cablemay be substituted, but this connection will not be balanced. Set the receiver’s MIC/LINE SWITCH to match the sound system’s input.3. Slide the transmitter’s POWER/OFF switch to the POWER position. The transmit-ter’s green POWER ON light and the receiver’s DIVERSITY A/B lights will glow.4. Slide the microphone’s ON/MUTE switch to the ON position to turn the micro-phone on.5. Talk or sing into the microphone. Normal operation is indicated by:•Steady glow of the receiver’s yellow DIVERSITY A/B lights.•Flickering of the receiver’s AUDIO PEAK light when loud sounds are transmitted.NOTE: If the receiver’s red AUDIO PEAK light does not flicker occasionally or isconstantly on, the transmitter gain may need to be adjusted. Refer to the Trans-mitter Audio Gain Adjustment section. Then, If the system is still not operatingproperly, consult the Troubleshooting table.6. When the performance is over, turn off the sound system and slide the transmit-ter’s POWER/OFF switch to the OFF position to conserve battery power.FIGURE 8UT2SHUREUT445°FRONT BACK9
ENGLISHOPERATING THE PRESENTER-UHF SYSTEM1. Refer to Figure 9. Connect the supplied ac power adapter to the DC INPUT con-nector on the back of the receiver. Insert the adapter’s cable into the power cableretainer. Plug the adapter into a wall socket or other ac power source (use PS20for 120 Vac, 60 Hz power; use PS20E for 230 Vac, 50 Hz power). The greenPOWER light on the receiver will glow.2. Connect the receiver’s XLR AUDIO OUT connector to the mixer input using an XLRto XLR audio cable. If no XLR cable is available, a 1/4” to 1/4” phone plug cable maybe substituted, but this connection will not be balanced. Set the receiver’s MIC/LINESWITCH to match the sound system’s input.3. Press the WL93, WL184 or WL185 lavalier microphone into the mounting clip andattach it to your garment. Do not cover the microphone with your clothing, andkeep it approximately 8 to12 inches below your chin. See Figure 9.4. Slide the recessed transmitter POWER/OFF switch to the POWER position. Thetransmitter’s green POWER ON light and the receiver’s yellow DIVERSITY A/Blights will glow.5. Slide the transmitter’s MUTE/ON switch to the ON position.6. Speak in your normal conversational voice. Proper operation is indicated by:•Steady glow of the receiver’s yellow DIVERSITY A/B lights.•Flickering of the receiver’s AUDIO PEAK light when you speak in a loud voice.NOTE: If the receiver’s red AUDIO PEAK light does not flicker occasionally or isconstantly on, the transmitter gain may need to be adjusted. Refer to the Trans-mitter Audio Gain Adjustment section. If the system is still not operating properly,consult the Troubleshooting table.7. When the presentation is over, turn off the sound system and slide the recessedtransmitter POWER/OFF switch to the OFF position to conserve battery power.FIGURE 9WL93SHURESHURE45°UT1UT4FRONT BACKshown10
ENGLISHOPERATING THE HEADSET-UHF SYSTEM1. Refer to Figure 10. Connect the supplied ac power adapter to the DC INPUT con-nector on the back of the receiver. Insert the adapter’s cable into the power cableretainer. Plug the adapter into a wall socket or other ac power source (use PS20for 120 Vac, 60 Hz power; use PS20E for 230 Vac, 50 Hz power). The greenPOWER light on the receiver will glow.2. Connect the receiver’s XLR AUDIO OUT connector to the mixer input using an XLRto XLR audio cable. If no XLR cable is available, a 1/4” to 1/4” phone plug cable maybe substituted, but this connection will not be balanced. Set the receiver’s MIC/LINESWITCH to match the sound system’s input.3. If using the headset for the first time, refer to the tag attached to the headset forassembly instructions. Adjust headband and place on head, as shown on tag. Forbest results, microphone should be placed 1/2” from side of mouth.4. Slide the recessed transmitter’s POWER/OFF switch to the POWER position.The transmitter’s green POWER ON light and the receiver’s yellow DIVERSITYA/B lights will glow.5. Slide the transmitter’s MUTE/ON switch to the ON position.6. Speak in your normal conversational voice. Proper operation is indicated by:•Steady glow of the receiver’s yellow DIVERSITY A/B lights.•Flickering of the receiver’s AUDIO PEAK light when you speak in a loud voice.NOTE: If the receiver’s red AUDIO PEAK light does not flicker occasionally or isconstantly on, the transmitter gain may need to be adjusted. Refer to the Trans-mitter Audio Gain Adjustment section. If the system is still not operating properly,consult the Troubleshooting table.7. When headset is not in use, turn off sound system and slide the recessed trans-mitter POWER/OFF switch to the OFF position to conserve battery power.FIGURE 10SHURESHUREUT1UT445°FRONT BACK11
ENGLISHOPERATING THE GUITARIST-UHF SYSTEM1. Refer to Figure 11. Connect the supplied ac power adapter to the DC INPUT con-nector in back of the receiver. Insert the adapter’s cable into the power cable retainer.Plug the adapter into a wall socket or other ac power source (use PS20 for 120 Vac,60 Hz power; use PS20E for 230 Vac, 50 Hz power). The green POWER light onthe receiver will glow.2. Connect the receiver’s 1/4” PHONE JACK AUDIO OUTPUT connector to the am-plifier input, using a standard guitar cable.3. Connect your guitar or bass to the transmitter input jack with a WA302 InstrumentAdaptor. NOTE: The Guitarist-UHF system may also be used with woodwind andbrass instruments with use of an optional WM98 miniature instrument microphoneand a horn mount. See Optional Accessories for additional information.4. Adjust the volume control on your guitar to desired level. To match wireless outputto that of a wired system, see Receiver Volume Adjustment for the Guitarist.5. Slide the transmitter’s POWER/OFF switch to the POWER position. The transmit-ter’s POWER ON light and the receiver’s DIVERSITY A/B lights will glow.6. Slide the transmitter MUTE/ON switch to the ON position.7. Play your guitar or bass. Normal operation is indicated by:•Steady glow of receiver’s yellow DIVERSITY A/B lights.•Flickering of the receiver’s AUDIO PEAK light when loud sounds are transmitted.NOTE: If the red AUDIO PEAK light does not flicker occasionally or is on constantly,the transmitter may need to be adjusted. Refer to the Transmitter Audio Gain Adjust-ment section. If the system is still not operating properly, consult the Troubleshootingtable.8. When the performance is over, turn off the amplifier and slide the recessed trans-mitter POWER/OFF switch to the OFF position to conserve battery power.FIGURE 11UT1SHURESHUREUT445°FRONT BACK12
ENGLISHRECEIVER VOLUME ADJUSTMENT FOR THE GUITARIST-UHFFollow these directions to adjust the volume control of the UT4 receiver, so that thewireless output of an instrument is equivalent to the output of a cabled instrument.1. Plug instrument directly into guitar/bass amp. Set volume and tone controls onboth the instrument and amplifier for a clean signal with desired tonal quality andvolume. DO NOT change these settings for the rest of volume adjustment.2. Unplug instrument from the amplifier input and plug into the transmitter. Plug thereceiver into amplifier input.3. Set VOLUME control of receiver at 1/4 on (9:00). Play instrument, with enoughforce to cause maximum output.4. If there is distortion present, the transmitter may be clipping. See the TransmitterAudio Gain Adjustment section.5. Adjust receiver volume control until sound quality matches that achieved in step 1.TRANSMITTER AUDIO GAIN ADJUSTMENTThe audio gain control on both the UT1 body-pack and UT2 hand-held transmittershas been factory-preset at the mid-range position for best performance in most ap-plications. If the red AUDIO PEAK light on the receiver does not flicker, the preset gainlevel may be too low and the audio gain may need to be increased until a proper signal-to-noise ratio is reached. This may be necessary for soft singers or talkers, or guitar orbasses with low outputs.For loud singers or talkers, or instruments with high outputs, the preset gain levelmay be too high, causing unwanted distortion. This condition is indicated by the con-tinuous glow of the red PEAK light on the receiver during usage.FIGURE 12+-UT1 BODY-PACK TRANSMITTER UT2 HAND-HELD TRANSMITTER•To Increase Gain: Rotate the transmitter gain control clockwise with the suppliedscrewdriver until the red AUDIO PEAK light on the receiver flickers when the gui-tar is played loudly or when you sing or speak in a loud voice. NOTE: In someapplications, the red AUDIO PEAK light will not flicker even with the gain controlturned fully clockwise. For body-pack systems only: If gain control is rotated fullyclockwise and the AUDIO PEAK light still does not flicker, check to see if the in-put attenuation switch on the transmitter is set to the –20 dB position. If it is, fullyrotate the gain control counterclockwise, and move the switch to the 0 dB posi-tion. Then rotate the gain control clockwise until the AUDIO PEAK light flickersduring high output or the gain control is turned fully clockwise.•To Reduce Gain: Rotate the transmitter gain control counterclockwise with the sup-plied screwdriver. Continue rotating the gain control until the red AUDIO PEAK lighton the receiver only flickers when guitar is played loudly, or when you sing orspeak in a loud voice. For body-pack systems only: If gain control is rotated fullycounterclockwise and the AUDIO PEAK light still glows continuously, check to see ifthe input attenuation switch on the transmitter is set to the 0 dB position. If it is, movethe switch to the –20 dB position, and fully rotate the gain control clockwise. Thenrotate the gain control counterclockwise until the AUDIO PEAK light flickers duringhigh output.To return audio gain to the factory setting, rotate the transmitter audio gain control to themid position and, on the body-pack only, slide the input attenuation switch to the 0 dBposition.13
ENGLISHBODY-PACK AUDIO GAIN AND ATTENUATION SETTINGSThe attenuation switch and the gain control on the UT1 body-pack are designed tobe used in conjunction to provide a wide spectrum of gain control choices. The fol-lowing ranges are starting points; actual output levels may vary.OUTPUT DEVICE ATTENUATIONSWITCH SETTINGAUDIO GAINCONTROL SETTINGLAVALIER MICROPHONE, CONVERSATIONAL VOICE 0 dB HIGH (clockwise)LAVALIER MICROPHONE, PROJECTED VOICEHEADSET, CONVERSATIONAL VOICE 0 dB MID–RANGEHEADSET, PROJECTED VOICEELECTRIC GUITAR/BASS, PASSIVE ELECTRONICS 0 dB LOW (counterclockwise)ELECTRIC GUITAR/BASS, PASSIVE ELECTRONICS –20 dB HIGH (clockwise)ELECTRIC GUITAR/BASS, ACTIVE ELECTRONICS –20 dB MID–RANGEELECTRIC GUITAR/BASS, ACTIVE ELECTRONICS –20 dB LOW (counterclockwise)RECEIVER SQUELCH ADJUSTMENTThe squelch control on the UT4 receivers (see figure 1) is factory preset for op-timum performance. No further adjustment is normally required. It is possible toadjust the squelch control setting to emphasize either signal quality or system range:•Turning the squelch control clockwise causes the receiver to demand a higherquality signal (less noise before muting), but decreases operating range.•Turning the squelch control counterclockwise allows a lower quality signalthrough (more noise before muting), but increases operating range.To return the receiver squelch control to the factory setting, rotate it to the mid-rangeposition (so the slot is vertical).TIPS FOR ACHIEVING MAXIMUM PERFORMANCE•Make sure you can always see a receiver antenna from the transmitter position.•Keep the distance from transmitter to receiver antenna as short as possible.•Point receiver antennas away from each other at a 45°angle from vertical.•Avoid placing the receiver antennas near metal surfaces and obstructions.•To mount the receiver on a flat surface, attach the four adhesive rubber feet orthe VELCRO mounting strips to the bottom of the receiver.•Monitor battery fuel gauge and replace battery as soon as red light is on.•Let body-pack transmitter antenna hang freely; do not coil or keep in pocket.•If stacking or rack mounting receivers in a multiple-system use situation, do notallow antennas to touch or cross.•Perform a walk-through before performance or presentation. If dead spots arefound, adjust location of receiver. If dead spots remain, mark spots and avoid.TROUBLESHOOTINGPROBLEM INDICATOR STATUS SOLUTIONNo sound. Green transmitter POWERlight off. Slide transmitter POWER ON/OFF switch to ONposition. Make sure battery is inserted properly, ob-serving battery polarity (“+/–”). If battery is insertedproperly, replace with fresh battery.No sound. Green transmitter POWERlight glowing. Slide transmitter MUTE/ON switch to ON position.No sound. Green receiver POWERlight off. Make sure ac adapter is securely plugged into elec-trical outlet and into dc input connector.Make sure ac electrical outlet works and suppliesproper voltage.No sound. Receiver DIVERSITY A/Blights glowing. PEAK lightflickers during loud sounds.Turn up receiver volume control.Confirm that the output connections from the receiv-er to the external equipment are secure.14
ENGLISHNo sound. Receiver DIVERSITY A/Blights off. Transmitter andreceiver POWER lightsglowing.Confirm transmitter’s and receiver’s frequencies match.Point receiver antennas away from each other at a 45°angle from vertical.Move receiver antennas away from any metal objects.Remove obstructions between transmitter and receiver.Make sure you can see receiver antennas.Move transmitter closer to receiver.Sound level differsfrom level of acabled instrument.Receiver DIVERSITY A/Blights glowing. Adjust transmitter gain as necessary.Adjust receiver volume as necessary.Sound level differswith different guitars. Receiver DIVERSITY A/Blights glowing. Readjust transmitter gain level to compensate for dif-ferences in guitar outputs.Distortion levelincreases gradually. Receiver DIVERSITY A/Blights and transmitter LOWBATTERY light glowing.Replace transmitter battery.Bursts of noise orother audible radiosignals present.DIVERSITY A/B lights on. Identify potential sources of interference (other rfsources) and turn off, remove or use a wireless sys-tem operating on a different frequency.Momentary loss ofsound as transmitteris moved aroundperforming area.Receiver DIVERSITY A/Blights off when sound islost.Reposition receiver and perform walk-through testagain. If audio dropouts persist, mark “dead” spotsand avoid them during performance.SYSTEM SPECIFICATIONSRF Carrier Frequency RangeApproximately 596 to 862 MHz (Available frequencies depend on applicable regu-lations in country where system is used).Operating Range:100 m (approximately 300 ft) under typical conditionsAudio Frequency Response: 20 to 16,000 Hz, $3 dBImage Rejection: 75 dB typicalSpurious Rejection: 75 dB typicalSystem Distortion (ref. 45 kHz deviation, 1 kHz modulation): 0.1% THD typicalSignal/Noise Ratio: 90 dBSensitivity: –110 dBm for 12 dB SINAD typicalMaximum Recommended Input Level, UT1 (attenuation switch at –20 dB, gain atminimum): +32 dBVMinimum Recommended Input Level, UT1 (attenuation switch at 0 dB, gain atmaximum): –80 dBVOperating Temperature Range–29° to 74° C (–20° to 165° F) NOTE: Battery characteristics may limit this range.Battery LifeUT1, UT2: 12 hours with 9 V alkaline battery (Duracell MN1604 recommended).UT1 BODY-PACK TRANSMITTER SPECIFICATIONSRF Output 15 mW TypicalInput Configuration UnbalancedConnector Type 4-pin Tini QG (male)Actual Impedance 1 MΩConnector PinAssignments Pin 1:Tied to GroundPin 2:Tied to +5 VPin 3:Tied to AudioPin 4:Tied to 20kΩ Resistor and Audio GroundDimensions 82.6 mm H x 63.5 mm W x 26.2 mm D(3.25” H x 2.50” W x 1.03” D)Net Weight 125g (4.4 oz.) including batteryPower Requirements 9 V alkaline battery (Duracell MN1604 recommended);9 V lithium ULTRALIFE battery optional.Nominal CurrentDrain 40 mA15
ENGLISHUT2 HAND-HELD TRANSMITTER SPECIFICATIONSUT2/58 (SM58) UT2/31(BG3.1)RF Output 15 mW TypicalDimensions 241 mm H x 51 mm D(9.49” H x 2.01” D) 225 mm H x 56 mm D(8.86” H x 2.20” D)Net Weight 296g (10.4 oz.) 218g (7.7 oz.)Power Requirement 9 V alkaline battery (Duracell MN1604 recommended);9 V lithium ULTRALIFE battery optional.Nominal Current Drain 40 mAUT4 RECEIVER SPECIFICATIONSConnector 3-Pin XLR (male) 1/4” phone plug (female)Maximum Output Levels Line Level: +10 dBVMic Level: –22 dBV +4 dBVNominal Output Levels Line Level: –26 dBVMic Level: –62 dBV –32 dBVOutput Configuration Active Balanced UnbalancedActual Impedance Line Level: 138 kΩ Mic Level: 500 Ω 1 kΩConnector PinAssignments Pin 1: groundPin 2: hotPin 3: coldTip: hotSleeve: groundDimensions 41 mm H x 197 mm W x 138 mm D(1.625” H x 7.77” W x 5.42” D)Net Weight 419.6g (14.8 oz.)Power Requirements 12–18 Vdc nominal, 200mAPower Supply 120 V or 230V ac adaptor with 2.1 mm female plugVoltage/Current/Phan-tom Power Protection Yes YesCERTIFICATIONUT1: Type Accepted under FCC Part 74. Certified by IC in Canada underRSS–123. Conforms to European Union directives, eligible to bear CE marking;meets European Union Requirements. ETSI Type Approval: pr I–ETS 300 422,EMC Immunity: ETS 300 445.UT2/31, UT2/58: Type Accepted under FCC Part 74. Certified by IC in Canada underRSS–123. Conforms to European Union directives, eligible to bear CE marking;meets European Union Requirements. ETSI Type Approval: pr I–ETS 300 442,EMC Immunity: ETS 300 445.UT4: Approved under the Notification provision of FCC Part 15. Certified by IC in Cana-da under RSS–123. Conforms to European Union directives, eligible to bear CEmarking; meets European Union Requirements. EMC Immunity: ETS 300 445.Power supply meets Low Voltage Directive: 73/23/EEC.FURNISHED ACCESSORIESScrewdriver 65A1659. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting Block (The Presenter Systems Only) RK329MB*. . . . . . . . . . . . . . . . . . Single-Mount Tie Bar (The Presenter Systems Only) RK240SB*. . . . . . . . . . . . . Windscreen (The Presenter Systems Only) RK242WS*. . . . . . . . . . . . . . . . . . . . . Receiver AC Adapter PS20 (120V), PS20E (230V). . . . . . . . . . . . . . . . . . . . . . . . . Vinyl Transmitter Bag (Body-Pack Systems Only) 26A13. . . . . . . . . . . . . . . . . . . . Vinyl Transmitter Bag (The Vocal Artist Systems Only) 26A14. . . . . . . . . . . . . . . . Swivel Adapter (The Vocal Artist Systems Only) WA370A. . . . . . . . . . . . . . . . . . . ∗ Replacements furnished in multiples of 4.16
ENGLISHOPTIONAL ACCESSORIES1/4” to 1/4” Cable (The Guitarist-UHF only) WA303. . . . . . . . . . . . . . . . . . . . . . . . . 1/4” to Tini QG Cable WA302. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 Meter (6 ft.) Receiver-Mixer Cable WA410. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rack Mount Tray URT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nylon Carrying Case WA590. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual Tie Clip (The Presenter-UHF w/WL184, WL185 only) RK183T2. . . . . . . . . Double Tie Clip (The Presenter-UHF w/WL93 only) RK307DB. . . . . . . . . . . . . . . . Miniature Instrument Microphone (Body-Pack Systems only) WM98. . . . . . . . . . Universal Horn Clamp (Body-Pack Systems only) A98KCS. . . . . . . . . . . . . . . . . . Miniature Instrument Microphone w/ Universal Horn Clamp WM98KCS. . . . . . . . Rubber Receiver Feet (4) 66A8053. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VELCRO Fastener, Hook (2) 80A8118. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VELCRO Fastener, Loop (2) 80A8119. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Amp/Powered Mixer Stand for UT4 Receiver WA595. . . . . . . . . . . . . . . . . . . . . . . . . Inline Audio Switch for UT1 Transmitter WA360. . . . . . . . . . . . . . . . . . . . . . . . . . . . For additional service or parts information, contact Shure’s Service department at1–800–516–2525. Outside the U.S., contact an Authorized Shure Service Center.VELCRO is a registered trademark of Velcro Industries B.V.LICENSING INFORMATIONIMPORTANT: Licensing of Shure wireless microphone equipment is the user’s re-sponsibility, and licensability depends on the user’s classification and applica-tion, and on the selected frequency. Shure strongly urges the user to contact the ap-propriate telecommunications authority concerning proper licensing, and beforechoosing and ordering frequencies. Changes or modifications not expressly ap-proved by Shure Incorporated could void your authority to operate the equipment.Operation of this equipment is subject to the following two conditions: (1) this devicemay not cause interference and (2) this device must accept interference, includinginterference that may cause undesired operation of the device.WARRANTY INFORMATIONShure Incorporated (“Shure”) hereby warrants that these products are free from de-fects in material and workmanship for a period of two years from the date of purchasefor all microphone cartridge and housing assembly parts and, for a period of one yearfrom date of purchase, all transmitter and receiver parts. At its option, Shure will re-pair or replace the defective product and promptly return it to you. You should retainproof of purchase to validate the purchase date and return it with any warranty claim.If you believe this product is defective within the warranty period, carefully repack theunit, insure it, and return it postpaid to:Shure IncorporatedAttention: Service Department222 Hartrey AvenueEvanston, IL 60202-5730 U.S.A.Customers outside the U.S.A. should ship the product to the authorized Shure Dis-tribution Center in their region.This warranty does not apply in cases of abuse or misuse of the product, use con-trary to Shure’s instruction, or unauthorized repair. All implied WARRANTIES ofMERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE are hereby dis-claimed and Shure hereby disclaims liability for incidental, special or consequentialdamages resulting from use or unavailability of this product.Some states do not allow limitations on how long an implied warranty lasts, or theexclusion or limitation of incidental or consequential damages, so the above limita-tion may not apply to you. This warranty gives you specific legal rights, and you mayhave other rights which vary from state to state.THIS WARRANTY SUPERSEDES ALL WARRANTIES THAT ARE INCLUDED WITHTHIS PRODUCT.17

Navigation menu