Shure M267 Users Manual User Guide English
M267 to the manual 79cc6cf3-0a24-4477-9b19-9276f3c503bf
2015-02-02
: Shure Shure-M267-Users-Manual-491116 shure-m267-users-manual-491116 shure pdf
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Shure Brothers Incorporated 222 Hartrey Avenue Evanston IL 60202-3696 U.S.A. Model M267 User Guide GENERAL The Shure Model M267 is a microphone mixer-remote amplifier specifically designed for professional applications. The excellent performance, versatility and features of this complete, compact console make it an ideal choice for studio, remote, or sound reinforcement use, and as an add-on mixer for expanding existing facilities. It is also ideally suited for use with audio and video tape recorders to provide multiple microphone inputs. Features: S S S S S S S S S S S Wide, flat frequency response and extremely low distortion up to +18 dBm output Extremely low noise and RF susceptibility Four switchable microphone- or line-level balanced-line inputs with individual gain controls and low-frequency rolloff switches. MUMETAL shielding on input transformers Feedback-type input gain controls for maximum clipping levels and dynamic range Output switchable for line or microphone level Built-in switchable peak limiter cuts output overload distortion, adapts to power supply voltage LED indicator shows limiter operation or overload with limiter defeated Externally adjustable limiter threshold (–4 to +18 dBm) VU meter calibrated for +4 and +8 dBm with range switch. Illuminated with ac operation Ac or built-in battery operation. Noiseless automatic switchover to battery in case of ac line failure. Battery test without program interruption Front-panel headphone level control and monitor jack drives almost any stereo or mono headphones; output can be additional unbalanced line feed to drive a tape recorder or power amplifier E1999, Shure Brothers Incorporated 27A8376 (SE) S S Direct mix bus for stacking units S Low distortion, high-stability tone oscillator for line test and level checks S All connections phased. Line output terminals phaseindicated S Compact and lightweight, with rugged, abrasion-resistant case S Internally selectable 120 or 240 Vac, 50/60 Hz operation S Underwriters’ Laboratories Listed and Canadian Standards Association listed as Certified Automatic muting prevents speaker damage during turn-on and -off SPECIFICATIONS Frequency Response 30 Hz to 20,000 Hz, ±2 dB Voltage Gain (at 1,000 Hz) (Outputs terminated: line 600 W, microphone 150 W, mix bus 3.3 kW, headphone 200 W, tip-sleeve and ringsleeve ) OUTPUT Inp t Input Line Microphone Mix Bus Low-Impedance Microphone (150 Ω) 91 dB 41 dB 24 dB Line 40 dB –9 dB –27 dB Mix Bus 55 dB 5 dB –– Inputs IMPEDANCE Input Microphone Line Mix Bus Designed for Use With Actual (Internal) 19 to 600 Ω 1 kΩ –32 dBV to –5 dBV∗ (25 mV to 0.56 V) Less than10 kΩ 66 kΩ +20 dBV 3.5 kΩ 3.5 kΩ +7 dBV (2.2 V) Input Clipping Level ∗Depending on input control setting Printed in U.S.A. Headphone Output Clipping Level Outputs 3.16V (+10 dBV) into 200 Ω IMPEDANCE Designed for Use With Actual (Internal) Output Clipping Level Any low impedance microphone input 0.5 –34 dB (20 mV) Mix Bus 3.5 kΩ 3.5 kΩ –8 dBV (400 mV) Headphones 8 - 2000 Ω 200 Ω recommended 400 Ω to 3 kΩ∗∗ +10 dBV (3.3 V) 600Ω 150Ω +18 dBm (6.2 V) Output Microphone Line Tone Oscillator 1,000 Hz, 1.5% or less THD Phantom Power 30 Vdc open-circuit, 3.3 kΩ series resistance, input switches in MIC position only Operating Voltage Ac Operation: 120 or 240 volts ±10%, 50/60 Hz, 9.5W, internally switchable[ ∗∗Depending on level control setting Noise Dc Operation: 27 volts nominal at 15 mA typical nosignal, 18 mA typical at 0 VU (+4 dBm) output with headphone load; 21.5 volts minimum Equivalent Input Hum and Noise: –126 dBV (low impedance microphone, 150 Ω - 20-20,000 Hz) into a 600 Ω load at full gain Battery life: approximately 20 hours with alkaline batteries at +4 dBm output in continuous use; three 9-volt batteries, type NEDA 1604A (Duracell MN1604 recommended) Output Noise: –75 dBV (master control fully counterclockwise), –53 dBV (master fully clockwise), (input controls down, 300-20,000 Hz) Output Hum and Noise: –70 dBV (master control down), –51 dBV (master control up) (input controls down, 20-20,000 Hz) [ Supplied wired for 120 Vac operation (See Service section for 240 Vac operation) Temperature Range Distortion 0.35% or less THD from 30 to 20,000 Hz at +15 dBm output; 0.5% or less IM distortion up to +15 dBm output level Operating: –18o to 57o C (0o to 135o F) Storage: –29o to 71oC (–20o to 160o F) Common Mode Rejection Dimensions 65 dB minimum with input of –20 dBV at 100 Hz See Figure 1 Control Interaction Less than 1 dB with any control combination 229 mm (9 in.) 309 mm (12 5/32 in.) Overload and Shorting Protection 68.8mm (2 23/32 in.) Shorting the outputs, even for prolonged periods, will cause no damage; microphone inputs will not be damaged by signals up to 3 volts 6.3 mm (1/4 in. ) Lo-Cut Filters FIGURE 1 6 dB/octave rolloff at 150 Hz Weight Limiter Net: Threshold: +15 dBm (line output level; adjustable from –4 to +18 dBm) Attack Time: 2.3 kg (5 lb 2 oz) Packaged: 3.2 kg (7 lb 2 oz) 3 msec typical Certifications Recovery Time: 500 msec typical Peak Indicator Listed by Underwriters’ Laboratories, Inc., and listed by Canadian Standards Association as Certified Lights 6 dB below clipping or at onset of limiter action 2 Input control 1 serves an additional function as the level control for the tone oscillator when the INPUT 1/OCS 1 switch is in the OSC 1 position. IMPORTANT: For optimum signal-to-noise ratio, the individual input controls should be operated at as high a setting as possible, consistent with maintaining adequate control range and input clipping level. CONTROLS AND CONNECTORS WARNING This apparatus must be earthed (grounded)! The M267 power supply is energized when the unit is connected to an ac source; disconnect mains (power) plug from supply when not in use. Master Gain Control Inputs The front-panel control designated MASTER is the master gain control which sets the overall output level of the mixed sources (including signals applied to the MIX BUS input). The four inputs are professional three-pin female XLR audio connectors located on the rear panel and designated INPUT 1 through INPUT 4. The inputs are balanced (internal transformer, MUMETAL shielded); pins 2 and 3 are “hot”, and pin 1 is “ground”. For microphone operation, the switches labeled LINE/MIC (directly above the input connectors) must be in the MIC position; for line level inputs, the switches must be in the LINE position. For impedance, clipping and operating signal levels, refer to the SPECIFICATIONS section. Limiter The front-panel LIMITER IN/OUT switch turns on a fastacting, peak-responding limiter circuit that cuts overload distortion during loud program intervals without affecting normal program levels. When the LIMITER switch is IN (operating), the mixer output is limited to approximately +15dBm. Increasing the individual or MASTER gain controls will increase the average output and the amount of limiting. The limiter threshold can be reset to any other output between –4 and +18 dBm if desired. With the limiter switched OUT and tone oscillator activated, adjust INPUT 1 and MASTER level controls to produce an output 0.5 dB higher than desired. Switch the limiter IN and set the LIMITER THRESHOLD ADJUST control (accessible though the bottom of the chassis) for the desired level. Outputs The rear-panel connector labeled OUTPUT is a professional three-pin male XLR audio connector. With the adjacent LINE/MIC switch in the MIC position, the OUTPUT connector is used to feed a low-impedance microphone line or a low-impedance microphone input. With the LINE/ MIC switch in the LINE position, the OUTPUT connector feeds the line-level input of an amplifier, tape recorder, or another mixer. The OUTPUT connector is a balanced output with the LINE/MIC switch in either position; pin 1 is ground, pins 2 and 3 are “hot”, and the connector is in phase with the corresponding pins of the input connectors. The front-panel PEAK LED indicator shows limiter operation with the limiter in, and operates when program levels approach overload with the limiter out. The indicator is much faster than a meter and will be activated by the shortest transient peak, but it remains on long enough to provide easy recognition. The rear-panel binding-post connector designated LINE OUTPUT is in parallel with the OUTPUT connector and can be used as a line-level output feed simultaneously with the OUTPUT connector. The terminals are numbered 2 and 3 and are in phase with the corresponding pins of the input connectors. While the line outputs can be used to drive various impedance lines, the VU meter is calibrated for use with a 600 Ω line. Low-Cut Filters The low-cut filters provide a low-frequency rolloff to the response curve as shown in Figure 2. The filters are activated by the LO-CUT IN/OUT switch above each individual input gain control and can be used individually with each control to reduce wind noise or undesirable low-frequency signals such as from condenser microphones or turntable rumble. The line output transformer will operate properly with up to 100 mA dc in the line. This feature permits the use of standard “dialed-up” telephone lines with dc across them. (Since a slight distortion increase may occur at high output levels with maximum dc current, operation with the VU RANGE switch at +4 dBm is recommended.) 0 Input Gain Controls –10 The front-panel controls designated 1 through 4 are the individual active gain controls for correspondingly numbered inputs. Note that the input connectors are located on the rear panel directly behind their corresponding gain control. The controls set the preamplifier gain and provide preamplifier output attenuation. As the gain is reduced, the preamplifier input clipping level is increased for that channel. –20 20 50 100 200 500 LOW-CUT FILTER ACTION FIGURE 2 3 1,000 Mix Bus Phantom Power Direct access to the mixing bus is provided through the rear-panel MIX BUS phono pin jack. This provision is made primarily to facilitate stacking or “multing” M267s to achieve additional input capacity without losing any inputs. With two M267s, for example, the two mixing buses are directly connected, providing two independent master gain controls and two isolated line amplifiers with eight individually controlled inputs. Since the buses are directly paralleled, a 6 dB drop in gain will occur; and the master or input controls must be increased to compensate. Noise specifications are not adversely affected by this interconnection. Mix bus interconnection can also be made with other Shure mixers, such as the M268, FP42. etc. The rear-panel PHANTOM OFF/ON switch controls the application of phantom power for condenser microphones, such as the Shure SM81 and SM87A, to all inputs. With the switch on and the rear-panel MIC/LINE switches in the MIC positions, +30 Vdc is applied to pins 2 and 3 of each input connection. Series current-limiting resistance is 3.3 kΩ for each input. When using other condenser microphones with the M267, verify that the voltage and resistance requirements are compatible. Note that the phantom power cannot normally be applied to the inputs with the MIC/LINE switches in the LINE position. IMPORTANT: Do not turn the PHANTOM switch on when using unbalanced low-impedance microphones; objectionable hum will result. Turn off the PHANTOM switch when condenser microphones are not being used. Use only high-quality cable. Intermittent shorts between broken shield wires and balanced conductors will cause offensive noise transients in the system. VU Meter The VU meter is factory-calibrated for use with a 600 Ω terminated line. The VU RANGE switch on the rear panel selects either a +4 or +8 dBm output at 0 VU meter indication. (This switch changes the meter indication but does not change the actual output level.) Microphone output levels are 50 dB below line output. The +4 range is recommended for normal use to provide approximately 14 dB of headroom from operating level to clipping level. BATTERY OPERATION AND EXTERNAL POWERING In addition to ac operation, the M267 can be operated from an internal battery pack. Current drain is typically 17 mA at +8 dBm output level and typically 15 mA at + 4 dBm. Battery power is recommended both for remote, on-location operation, and as an emergency backup source in case of failure of the ac power. The VU meter is illuminated by two No. 86 lamps operating well under their normal ratings for a life expectancy of greater than 10,000 hours. The lamps are only lit during ac operation. Consequently, the illumination serves as a visual alarm if the ac is interrupted and the unit has switched to battery. Access to the battery compartment is provided at the bottom of the chassis. Three 9-volt alkaline batteries power the M267 at full rated output. Use alkaline batteries for maximum life. Duracell MN1604A or Eveready 522 are recommended. Battery life is approximately 20 hours at +4 dBm continuos use. Note that battery operation with phantom power loads and high level headphone monitoring will increase battery drain. The VU meter is connected on the primary side of the output transformer to assure protection from any dc level on a telephone line. Headphones The headphone outlet appears at the front-panel jack panel designated PHONES. The two-circuit phone jack will accommodate most stereo or mono headphones. The output level is sufficient to provide high volume for use in noisy environments. With batteries in the battery compartment, the M267 will automatically and silently switch to battery operation should the ac voltage fall below a suitable level. If the ac power fails completely, the VU meter lamps will go out, providing a visual indication of line failure. Note that the headphone output level is also high enough to use as an auxiliary unbalanced line feed to drive a tape deck or a power amplifier. Battery condition can be determined by using the BATT CHECK switch on the front panel. Activate the BATT CHECK switch and observe the VU meter. A new set of batteries will give about a +2 VU indication. Battery condition is good if the reading is above 0 VU; a lower reading means that new batteries are required for proper operation. Note that the M267 power switch must be turned on to check battery condition. The tip and ring connections of the headphone plugs are in phase with pin 3 of all input and output connectors, and with the tip of the MIX BUS jack. Tone Oscillator The highly stable, low-distortion tone oscillator provides for line test and level checks. The oscillator is instantly activated by the front-panel INPUT 1/OSC 1 switch; its level can then be controlled by the INPUT 1 gain control on the front panel. The tone oscillator frequency is 1,000 Hz, and the signal appears on both the line and microphone outputs, as well as the headphone and mix bus connectors. The oscillator should be switched off (INPUT 1 position) when not in use. Telephone Interconnection When using the M267 connected directly to a telephone line, check to see whether the local telephone company requires an interface coupler between the M267 and the telephone line. If a coupler is required, make certain the coupler selected and the wiring arrangement are in compliance with the telephone company regulations. 4 3. Locate the voltage selector switch (S201) at the right rear of the main printed circuit board (Figure 3). Move SD201 to the 240V position (toward the front panel). Telephone Line Surge Protection When using the M267 connected directly to a telephone line subject to lightning-induced voltage surges, the following commercially available part can be installed across the LINE OUT terminals to provide additional protection for output circuit components: Metal Oxide Varistor, General Electric Co., Type No. V22ZA1 WHT BLK 120V T206 F202 T50/250V F201 ACCESSORIES A268R Rack Panel Kit. The Model A268R Rack Panel Kit includes a 19 in. x 3-1/2 in. (483 mm x 89 mm) precut rack panel and necessary hardware for rack-mounting the M267 (with its cover in place and end caps removed) in a standard 19 in. (483 mm) rack panel. RKC169 Rack Panel Bracket Kit. The Model RKC169 Rack Panel Bracket Kit enables owners of the Shure A68R Rack Panel Kit (originally designed for the M67 and M68 Mixers) to rack-mount the M267 with the A68R. S201 240V 240 V WIRING FIGURE 3 4. Remove fuse F201 (0.1A, 250V, time lag) and replace it with the supplied fuse F202 (0.05A, 250V, time lag). Note that the F202 fuse holder is at right angles to the F201 fuse holder. 5. Replace the ac line cord (if necessary) with one designed for the 240 Vac source. If the M267 is to be used outside the U.S. and Canada, local regulations may require replacing the line cord with one having wire insulation colors as follows: SERVICE WARNING Voltages in this equpment are harzardous! Refer servicing to qualified service personnel. 240 Vac Operation To change the M267 operating voltage from 120 Vac to 240 Vac, follow these steps: 1. Disconnect the M267 from the ac line. 2. Remove the end caps and cover. “Live” or “Hot” Neutral Earth or Ground U.S., Canada Black White Green Europe Brown Blue Green/ Yellow 6. Replace the cover and end caps, and mark the rear panel to reflect the new operating voltage. 5 PRINTED CIRUCIT BOARDS COMPONENT SIDE INPUT TRANSFORMERS T201-T204 6 REPLACEMENT PARTS LIST REFERENCE DESIGNATION PART NUMBER DESCRIPTION COMMERCIAL ALTERNATE C101,C209, C219, C227, C232 86T628 Capacitor, Electrolytic, 5 µF, 25V Sprague TVA 1303 C115 86L628 Capacitor, Electrolytic, 250 µF, 50V REFERENCE DESIGNATION Sprague 501D227F063PR PART NUMBER DESCRIPTION COMMERCIAL ALTERNATE PL301-PL302 95A8010 Lamp, 6.3V, 0.2A Sylvania 86 Q201 86A350 Transistor, NPN Motorola 2N5210 Q202, Q204 86A334 Transistor, NPN Rohm TIS92 Q203, Q205 86A348 Transistor, PNP Motorola 2N5087 C201, C204C205, C208 86V628 Capacitor, Electrolytic, 22 µF, 6.3V Sprague 501D226F016LL Q206 86A335 Transistor, PNP Rohm TIS93 C210 C212-C213 86M630 86R630 Capacitor, Electrolytic, 10 µF, 25V Capacitor, Electrolytic, 68 µF, 25V Sprague TE 1204 Sprague 501D686F025MN Q207 86A8302 Transistor, PNP Motorola TIP30A R250 46A8016 Potentiometer, 100k None C215, C218 86L626 Capacitor, Electrolytic, 470 µF, 35V Sprague 503D477F035QE R302, R306, R310, R314 46B8000 Potentiometer, 100k None C216, C222 C221, C229 C223 D209, D211-D214, D222-D223, D226-D229 D210, D217, D230-D235 86A630 86N630 86S628 86A415 Capacitor, Electrolytic, 5 µF, 35V Capacitor, Electrolytic, 22 µF, 35V Capacitor, Electrolytic, 1 µF, 50V Diode, Silicon, Computer, 75V Sprague TE1303 Mallory F226KM Sprague TVA1300 TI 1N4148 R317 46C8000 Potentiometer, 200k None R322 46D8000 Potentiometer, 5k None S101-S104 55B8008 Switch, Slide, 3PDT None S105, S302, S306 55B8007 Switch, Slide, DPDT None 55B8001 Switch, Slide, DPDT None 86A404 Silicon Rectifier, 100V, 1/2A Motorola 1N4002 S106-S107, S301, S303-S305 S201 55A8035 Switch, Slide, DPDT Switchcraft EPS1-PC1 D218-D221 D301 86A405 86F422 Diode, Germanium, 30V Diode,Light-Emitting RCA 1N48, 1N60 General Instrument MV5075C S307 90CB2600 Switch, Pushbutton, SPDT Switchcraft 953 S308 55A8009 Switch, Slide, 3PDT None F201 80F159 Fuse, Slow–Blow, 3AG, 0.1A, 250V Littlefuse 313000 Series T201-T204 95B8165 Transformer, Input None F202 J1 J2A, B J101-J104 J105 J301 L101-L113 80C380 95C450 90T2600 95B8011 95B8012 90BJ2600 80A365 Fuse, Time Lag, 0.05A, 250V Jack, Phono Connectors, Binding Post Connector, 3-Pin Female XLR Connector, 3-Pin Male XLR Phone Jack Ferrite Bead Ring Schurter 034.3104 Switchcraft 3511A None Switchcraft Y3FDPC Switchcraft Y3MPC Switchcraft L-1128PC Panasonic Exc-ELSA35 T205 51E235A Transformer, Output None T206 51A8021 Transformer, Power None U201 86B808A Integrated Circuit, Quad Op Ampl (Selected for NF) Raytheon RC4156N U202 86A8908 Opto-Isolator None U203 86A811A Integrated Circuit, Dual Op Ampl Raytheon RC4559NB U204 86A806A Integrated Circuit, Quad Comparator Raytheon LM339DB M1 RKC170 (95A8214) Meter, 190 µA None U205 86A811A Integrated Circuit, Dual Op Ampl Raytheon RC4559NB U206 86A803 Integrated Circuit, Dual Op Ampl Motorola MC1458C-P1 90A8028 90A8029 90A8027 65A8008 Knob, MIC 1-4, MASTER Knobs, PHONE Cover, Battery End Cap U207 86B8930 Integrated Circuit, Voltage Regulator National Semiconductor LM317AT W1 90A8045 Line Cord, AC None MP1-MP5 MP6 MP7 MP8-MP9 None None None None Parts listed as RKC Kits should be ordered by that kit number. 9
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 1999:05:24 12:22:15 Producer : Acrobat Distiller Daemon 3.01 for HP-UX A.09.01 and later (HPPA) Author : Shure Incorporated Creator : Interleaf, Inc. Title : Shure M267 User Guide English Modify Date : 2007:02:07 10:50:30-06:00 Page Count : 8EXIF Metadata provided by EXIF.tools