Sichuan AI Link Technology WFM603UWS2 Wireless Module User Manual

Sichuan AI-Link Technology Co.,Ltd. Wireless Module Users Manual

User Manual

WF-M603-UWS2 Wireless Module Features：➢ Supported WLAN Standard IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n ➢ Chip Solution Mediatek MT7603U ➢ Size 40mm*33mm*5.5mm Model Overview： Model Standard Rate Band Ant Power WF-M603-UWS2 IEEE 802.11b/g/n 300Mbps 2.4G Internal Antennas 5V Sichuan AI-Link Technology Co.,Ltd. Add: Anzhou,Industrial park,Mianyang,Sichuan Tell: +86-13881190925 Web : http://www.changhong.com
WF-M603-UWS2 IEEE 802.11b/g/n 2T2R USB WIFI Module Sichuan AI-Link Technology Co.,Ltd. page 2 of 9 Record of Modification Version Date of modification Main content of modification Reason of modification Serial number of modification Confirm V1.0 2018/11/24 First release Huang Wei
WF-M603-UWS2 IEEE 802.11b/g/n 2T2R USB WIFI Module Sichuan AI-Link Technology Co.,Ltd. page 3 of 9 1. Introduction WF-M603-UWS2 module design is based on Mediatek MT7603U solution, The MT7603U is a highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio. The Module is a highly integrated MAC/BBP and 2.4 PA/LNA single chip which supports a 300Mbps PHY rate. The Module is designed to support standard-based features in the areas of security, quality of service, and international regulations, giving end users the greatest performance anytime and in any circumstance. This documentation describes the engineering requirements specification. 1.1 RF module Overview The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based on Mediatek MT7603U. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN (WLAN) network interface controller complying with the 802.11 specification over USB interface. It combines a MAC, a 2T2R capable baseband, and RF in a single chip. An intelligent Wi-Fi coexistence algorithm is implemented to provide the best harmonized Wi-Fi radio performance. Figure 1 WF-M603-UWS2 Block Diagram 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n
WF-M603-UWS2 IEEE 802.11b/g/n 2T2R USB WIFI Module Sichuan AI-Link Technology Co.,Ltd. page 4 of 9 1.3 System Functions Table1: General Specification as below: Main Chipset Mediatek MT7603U Operating Frequency 2.4G WiFi Standard 802.11 b/g/n Modulation WIFI:11b: DBPSK, DQPSK and CCK and DSSS 11g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM Data rates 11b: 1, 2, 5.5 and 11Mbps 11g: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 11n: MCS0~15, up to 300Mbps Form factor 7pins Host Interface USB 2.0 PCB Stack 2-layers designDimension Typical，40mm x 33mm x 5.5mm Antenna Integral Antennas Design , peak gain：2dBi Operation Temperature -10℃ to +60℃Storage Temperature -40℃ to +125℃Operation Voltage 5V +/-5% Current Consumption 410mA 2. Mechanical Specification2.1 Mechanical Outline Drawing Typical Dimension (W x L ): 40.0mmx 33.0mm x 5.5mm General tolerance: ±0.2mm
WF-M603-UWS2 IEEE 802.11b/g/n 2T2R USB WIFI Module Sichuan AI-Link Technology Co.,Ltd. page 5 of 9 2.2 Product Picture Top view bot view 2.3 Pin define Pin Define 1 5V 2 DN 3 DP 4 GND 5 GND 6 WOW 7 RESET
WF-M603-UWS2 IEEE 802.11b/g/n 2T2R USB WIFI Module Sichuan AI-Link Technology Co.,Ltd. page 6 of 9 3. Electrical SpecificationThis Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0℃,+25℃,+40℃) and overall voltage (4.75V,5V,5.25V). 3. 1 IEEE 802.11g/a Section:Items Contents Specification IEEE802.11g Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH1 to CH13 @ 11g Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels15dBm Target (For Each antenna port) @ 11g/6Mbps~54Mbps 11 13 15 dBm 2. Spectrum Mask @ Target Power1) at fc +/-11MHz- - -20dBr 2) at fc +/-20MHz- - -28dBr 3) at fc > +/-30MHz- - -40dBr 3.Constellation Error(EVM) @ Target Power1) 6Mbps- - -5dB 2) 9Mbps- - -8dB 3) 12Mbps- - -10dB 4) 18Mbps- - -13dB 5) 24Mbps- - -16dB 6) 36Mbps- - -19dB 7) 48Mbps- - -22dB 8) 54Mbps- - -25dB 4. Frequency Error1) IEEE802.11g-15- 15 ppm 2) IEEE802.11a-1515 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain)1) 6Mbps (PER ≦10%)- - -82dBm 2) 9Mbps (PER ≦10%)- - -81dBm 3) 12Mbps (PER ≦10%)- - -79dBm 4) 18Mbps (PER ≦10%)- - -77dBm 5) 24Mbps (PER ≦10%)- - -74dBm 6) 36Mbps (PER ≦10%)- - -70dBm 7) 48Mbps (PER ≦10%)- - -66dBm 8) 54Mbps (PER ≦10%)- - -65dBm 6. Maximum Input Level (PER ≦10%)1) IEEE802.11g-20- - dBm 2) IEEE802.11a-30dBm
WF-M603-UWS2 IEEE 802.11b/g/n 2T2R USB WIFI Module Sichuan AI-Link Technology Co.,Ltd. page 7 of 9 3.2 IEEE 802.11b Section: Items Contents Specification IEEE802.11b Mode DBPSK, DQPSK and CCK and DSSS Channel CH1 to CH13 Data rate 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels(Calibrated)1) 17dBm Target (For Each antenna port)@1Mbps~11Mbps13 15 17 dBm 2. Spectrum Mask @ Target Power1) fc +/-11MHz to +/-22MHz- - -30dBr 2) fc > +/-22MHz- - -50dBr 3.Constellation Error(EVM) @ Target Power1) 1Mbps- - -10dB 2) 2Mbps- - -10dB 3) 5.5Mbps- - -10dB 4) 11Mbps- -20 -10dB 4. Frequency Error-15- 15 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain)1) 1Mbps (FER ≦8%)- -83 -76dBm 2) 2Mbps (FER ≦8%)- -80 -76dBm 3) 5.5Mbps (FER ≦8%)- -79 -76dBm 4) 11Mbps (FER ≦8%)- -76 -76dBm 6. Maximum Input Level (FER ≦8%)-10- - dBm
WF-M603-UWS2 IEEE 802.11b/g/n 2T2R USB WIFI Module Sichuan AI-Link Technology Co.,Ltd. page 8 of 9 3.3 IEEE 802.11n HT20 Section: Items Contents Specification IEEE802.11n HT20 @ 2.4G Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH1 to CH13 @ 2.4G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels1) 15dBm Target (For Each antenna port)@ 2.4G/MCS0~MCS710 12 14 dBm 2. Spectrum Mask @ Target Power1) at fc +/-11MHz- - -20dBr 2) at fc +/-20MHz- - -28dBr 3) at fc > +/-30MHz- - -45dBr 3. Constellation Error(EVM) @ Target Power1) MCS0- - -5dB 2) MCS1- - -10dB 3) MCS2- - -13dB 4) MCS3- - -16dB 5) MCS4- - -19dB 6) MCS5- - -22dB 7) MCS6- - -25dB 8) MCS7- - -28dB 4. Frequency Error1) IEEE802.11n HT20 @ 2.4G-15- 15 ppm 2) IEEE802.11n HT20 @ 5G-15- 15 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain)1) MCS0 (PER ≦10%)- - -82dBm 2) MCS1 (PER ≦10%)- - -79dBm 3) MCS2 (PER ≦10%)- - -77dBm 4) MCS3 (PER ≦10%)- - -74dBm 5) MCS4 (PER ≦10%)- - -70dBm 6) MCS5 (PER ≦10%)- - -66dBm 7) MCS6 (PER ≦10%)- - -65dBm 8) MCS7 (PER ≦10%)- - -64dBm 6. Maximum Input Level (PER ≦10%)1) IEEE802.11n HT20 @ 2.4G-20- - dBm 2) IEEE802.11n HT20 @ 5G-30- - dBm
WF-M603-UWS2 IEEE 802.11b/g/n 2T2R USB WIFI Module Sichuan AI-Link Technology Co.,Ltd. page 9 of 9 3.4 IEEE 802.11n HT40 Section: Items Contents Specification IEEE802.11n HT20 @ 2.4G Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH3 to CH11 @ 2.4G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels (Calibrated)1) 14dBm Target (For Each antenna port)@ 2.4G/MCS0~MCS710 12 14 dBm 2. Spectrum Mask @ Target Power1) at fc +/-21MHz- - -20dBr 2) at fc +/-40MHz- - -28dBr 3) at fc > +/-60MHz- - -45dBr 3. Constellation Error(EVM) @ Target Power1) MCS0- - -5dB 2) MCS1- - -10dB 3) MCS2- - -13dB 4) MCS3- - -16dB 5) MCS4- - -19dB 6) MCS5- - -22dB 7) MCS6- - -25dB 8) MCS7- - -28dB 4. Frequency Error1) IEEE802.11n HT20 @ 2.4G-15- 15 ppm 2) IEEE802.11n HT20 @ 5G-15- 15 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain)1) MCS0 (PER ≦10%)- - -79dBm 2) MCS1 (PER ≦10%)- - -76dBm 3) MCS2 (PER ≦10%)- - -74dBm 4) MCS3 (PER ≦10%)- - -71dBm 5) MCS4 (PER ≦10%)- - -67dBm 6) MCS5 (PER ≦10%)- - -63dBm 7) MCS6 (PER ≦10%)- - -62dBm 8) MCS7 (PER ≦10%)- - -61dBm 6. Maximum Input Level(PER ≦10%)1) IEEE802.11n HT20 @ 2.4G-20- - dBm 2) IEEE802.11n HT20 @ 5G-30- - dBm 4. Software RequirementsThe driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7. Mfg. software tool is MT7603U_QA_Tool.
CE tatementHerby, Sichuan AI-Link Technology Co., Ltd. declares that this Wireless Module，WF-M603-UWS2 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.Use the WF-M638-UWP1 in the environment with the temperature between 0℃ and 60℃Operation Frequency range: 2412MHz~2472MHz (802.11b/802.11g/802.11n(HT20)) 2422MHz~2462MHz (802.11n(HT40))Max RF Output Power: Manufacturer：Sichuan AI-Link Technology Co., Ltd.Address：Anzhou, Industrial park, Mianyang, Sichuan, ChinaTel: +86- 0816-2438701Fax: +86- 0816-2438701E-mail: caixia.hu@changhong.comFCC StatementChanges or modifications not expressly approved by the party responsible for compliance could voidthe user's authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates uses and canradiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.-- Consult the dealer or an experienced radio/TV technician for helpThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions(1)this device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your bodyFCC Radiation Exposure StatementThe modular can be installed or integrated in mobile or fix devices only. This modular be installed inany portable device, for example, USB dongle like transmitters is forbidden. This modular complieswith FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter mustnot be collocated or operating in conjunction with antenna or transmitter. If the FCC identificationnumber is not visible when the module is installed inside another device, then the outside of the deviceinto which the module is installed must also display label referring to the enclosed module. Thisexterior label can use wording such as the following:” Contains Transmitter Module FCC ID: 2AOKI-WFM603UWS2 Or Contains FCC ID: 2AOKI-WFM603UWS2 when the module is installed inside anotherdevice, the user manual of this device must contain below warning statements;1. This device complieswith Part 15 of the FCC Rules. Operation is subject to the following two conditions :(1) This device maynot cause harmful interference.(2) This device must accept any interference received, includinginterference that may undesired operation.2. Changes or modifications not expressly approved by theparty responsible for compliance could void the user's authority to operate the equipment. The devicesmust be installed and used in strict accordance with the manufacturer’s instructions as described inthe user documentation that comes with the product. This device is intended only for OEM integratorsunder the followingconditions:1) The antenna must be installed such that 20 cm is maintained betweenthe antenna and user.2) The transmitter module may not be co-located with any other transmitter orantenna. Module Antenna Type: Integral Antenna, ANT Gain: 2dBi0.0356W
IC StatementThis device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to thefollowing two conditions:(1) This device may not cause interference; and(2) This device must accept any interference, including interference that may cause undesiredoperation of the device.The term “IC: “ before the certification/registration number only signifies that the Industry Canadatechnical specifications were met. This product meets the applicable Industry Canada technicalspecifications.Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio exemptsde licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pasproduire de brouillage,et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillageest susceptible d'en compromettre le fonctionnement

Navigation menu