Sichuan AI Link Technology WFM668UWP1 Wireless Module&Bluetooth; Module User Manual 01 23

Sichuan AI-Link Technology Co.,Ltd. Wireless Module&Bluetooth; Module 01 23

Contents

Users manual

Sichuan AI-Link Technology Co., Ltd. page 1 of 17 WF-M668-UWP1 Wireless Module&Bluetooth Module Features： ¾ Reserving System IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11a IEEE Std. 802.11ac Bluetooth 2.1+EDR,4.2 LE,5.0 ¾ Chip Solution MT7668AUN ¾ Band 2.4G+5 G Model Standard Rate Channel POWER IEEE 802.11a/b/g/n/ac 866.7Mbps 2.4G/5G WF-M668-UWP1 Bluetooth 5.0 3Mbps 2.4G 5V Sichuan AI-Link Technology Co.,Ltd Add: Anzhou, Industrial park, Mianyang, Sichuan, China Fax : +86-0816-2416943 http://www.changhong.com
Sichuan AI-Link Technology Co., Ltd. page 2 of 17 Record of Modification Feedback of customer’s Confirmation We accept the specification after Confirmed Customer name Customer signature Confirmation Date Please feed back this paper and first paper after your signature by the address,thanks! ADD： Anzhou,Industrial park,Mianyang,Sichuan,China Factory： Sichuan AI-Link Technology Co.,Ltd. Approved Checked Designed Product WIFI Module WF-M668-UWP1 Date 2017-11-10
Sichuan AI-Link Technology Co., Ltd. page 3 of 17 No Date of modification Main content of modification Reason of modification Serial number of modification Confirm A 2017-11-10 Confirmed for the first time Fan xijun
Sichuan AI-Link Technology Co., Ltd. page 4 of 17 1. Introduction WF-M668-UWP1 is based on MT7668AUN,complied with IEEE 802.11ab/g/n/ac dual-band WIFI subsystem and a Bluetooth subsystem.. 1.1 RF module Overview The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based on MTK MT7668AUN. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN (WLAN) USB2.0 network interface controllercomplying with the 802.11n specification. It combines a MAC, a 2T2R capable baseband,and RF in a single chip. The MT7668 provides a complete solution for a highthroughput performance wireless client.The Bluetooth subsystem contains the Bluetooth radio,baseband,link controller.It also uses the 32-bit RISC MCU for the Bluetooth protocols. Figure 1 WF-M668-UWP1 Block Diagram 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11a _ IEEE Std. 802.11ac 1.3 System Functions Table1: General Specification as below: Standard IEEE 802.11 b/a/ac/g/n Bluetooth 2.1+EDR,4.2 LE,5.0 Interface USB 2.0 ANT 2T2R Modulation 802.11b:DBPSK,DQPSK,CCK for DSSS 802.11a/g:BPSK,QPSK,16QAM,64QAM for OFDM 802.11n:BPSK,QPSK,16QAM,64QAM for OFDM 802.11ac:BPSK, QPSK, 16QAM, 64QAM ,256QAM for OFDM BT: FHSS/GFSK/DQPSK/8DPSK
Sichuan AI-Link Technology Co., Ltd. page 5 of 17 Operating Frequency 2.400 ~ 2.4835 GHz,5.150~5.350 GHz,5.470~5.725 GHz,5.725~5.850 GHz TX Power WiFi: 11b: 17 +/- 1.5dBm (11Mbps) 11g: 15 +/- 1.5dBm (54Mbps) 11a: 15 +/- 1.5dBm (54Mbps) 11n: 15 +/- 1.5dBm (MCS7 HT20) 11n: 15 +/- 1.5dBm (MCS7 HT40) 11ac: 13 +/- 1.5dBm (MCS9 HT20) 11ac: 13 +/- 1.5dBm (MCS9 HT40) 11ac: 13 +/- 1.5dBm (MCS9 HT80) BT: DH5,Class 1(5dBm Typical) Frequency offset ≤+-15PPM EVM 11b @ 11Mbps: (Max.) : 35%, (Typical) : 6% 11a/g @ 54Mbps: (Max.) : -25dB , (Typical) : -30dB 11n @ MCS7 (2.4G/5.8GHT20): (Max.) : -28dB, (Typical) : -32dB 11n @ MCS7 (2.4G/5.8G HT40): (Max.) : -28dB, (Typical) : -32dB 11n @ MCS7 (ac HT20): (Max.) : -28dB, (Typical) : -32dB 11n @ MCS7 (ac HT40): (Max.) : -28dB, (Typical) : -32dB 11n @ MCS7 (ac HT80): (Max.) : -28dB, (Typical) : -32dB RX Sensitivity WiFi: 11b @ 11Mbps: (Max.): -85dBm, (Typical): -86dBm (PER<8%) 11g @ 54Mbps: (Max.): -65dBm, (Typical): -73dBm (PER<10%) 11n @ MCS7 (2.4G/5.8G HT20): (Max.): -64dBm, (Typical): -71dBm (PER<10%) 11n @ MCS7 (2.4G/5.8G HT40): (Max.): -61dBm, (Typical): -68dBm (PER<10%) 11ac@ MCS9(HT20): (Max.): -57dBm, (Typical): -67dBm (PER<10%) 11ac@ MCS9(HT40): (Max.): -54dBm, (Typical): -63dBm (PER<10%) 11ac@ MCS9(HT80): (Max.): -51dBm, (Typical): -58dBm (PER<10%) BT: GFSK: typical -93dBm π/4 DQPSK: typical -93dBm 8DPSK: typical -87dBm -97 dBm(BLE) Channel 2.4GHz：CH1-CH13 5.8GHz：CH36-CH165 Operation Voltage 5V+/-5% Power consumption WIFI
Sichuan AI-Link Technology Co., Ltd. page 6 of 17 BT ANT ＢＴ　gain 1dBi，２．４Ｇ／5G ＷＩＦＩgain 2dbi Operation Temperature -10℃ to +70℃ Storage Temperature -40℃ to +125℃ Hardware version JUB7.820.0243-1 Software version customer_package_UIv1.84_DLLv3.84_20170627_WinDriverV.0.0.4.26_FWv.66103 above.
Sichuan AI-Link Technology Co., Ltd. page 7 of 17 2. Mechanical Specification Typical Dimension (W x L x T): 70mmx 33mm x6.0mm (tolerance : +/-0.2 mm) PCB Thickness: 1.0mm
Sichuan AI-Link Technology Co., Ltd. page 8 of 17 NO Defintion NOTE 1 DC_EN Control the DC/DC to reset the Module 2 NC No Connect 3 VCC Power supply 4 DN USB D- 5 DP USB D+ 6、7 GND Ground 8 3D_SYNC 3D signal synchronization 9 REG_ON Reset 10 WLAN_DEV_WAKE WIFI wake host 3. Product Picture 10 1 Top view Bottom view Noet: No marked size tolerance: ±0.2mm 4. Electrical Specification
Sichuan AI-Link Technology Co., Ltd. page 9 of 17 This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0℃,+25℃,+60℃) . 4 1 IEEE 802.11g/a Section: Items Contents Specification IEEE802.11g IEEE802.11a Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH1 to CH13 @ 11g CH36 to CH165 @ 11a Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Remark1. Power Levels 1) 15dBm Target (For Each antenna port) @ 11g 13 15 17 dBm 2) 14dBm Target (For Each antenna port) @ 11a 13 15 17 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) 6Mbps - - -5 dB 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - - -25 dB 4. Frequency Error 1) IEEE802.11g -10 - 10 ppm 2) IEEE802.11a -10 10 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER ≦10%) - - -82 dBm 2) 9Mbps (PER ≦10%) - - -81 dBm 3) 12Mbps (PER ≦10%) - - -79 dBm 4) 18Mbps (PER ≦10%) - - -77 dBm 5) 24Mbps (PER ≦10%) - - -74 dBm 6) 36Mbps (PER ≦10%) - - -70 dBm 7) 48Mbps (PER ≦10%) - - -66 dBm 8) 54Mbps (PER ≦10%) - - -65 dBm 6. Maximum Input Level (PER ≦10%) 1) IEEE802.11g -20 - - dBm 2) IEEE802.11a -30 dBm 4.2 IEEE 802.11b Section: Items Contents
Sichuan AI-Link Technology Co., Ltd. page 10 of 17 Specification IEEE802.11b Mode DBPSK, DQPSK and CCK and DSSS Channel CH1 to CH13 Data rate 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max. Unit Remark1. Power Levels(Calibrated) 1) 17dBm Target (For Each antenna port) 15 17 19 dBm 2. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz - - -30 dBr 2) fc > +/-22MHz - - -50 dBr 3. Constellation Error(EVM) @ Target Power 1) 1Mbps - - -10 dB 2) 2Mbps - - -10 dB 3) 5.5Mbps - - -10 dB 4) 11Mbps - -20 -10 dB 4. Frequency Error -10 - 10 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 1Mbps (FER ≦8%) - -83 -76 dBm 2) 2Mbps (FER ≦8%) - -80 -76 dBm 3) 5.5Mbps (FER ≦8%) - -79 -76 dBm 4) 11Mbps (FER ≦8%) - -76 -76 dBm 6. Maximum Input Level (FER ≦8%) -10 - - dBm 4.3 IEEE 802.11n HT20 Section: Items Contents Specification IEEE802.11n HT20 @ 2.4G
Sichuan AI-Link Technology Co., Ltd. page 11 of 17 IEEE802.11n HT20 @ 5G Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH1 to CH13 @ 2.4G CH36 to CH165 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 14dBm Target (For Each antenna port) @ 2.4G 13 15 17 dBm 2) 13dBm Target (For Each antenna port) @ 5G 13 15 17 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G -10 - 10 ppm 2) IEEE802.11n HT20 @ 5G -10 - 10 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) - - -82 dBm 2) MCS1 (PER ≦10%) - - -79 dBm 3) MCS2 (PER ≦10%) - - -77 dBm 4) MCS3 (PER ≦10%) - - -74 dBm 5) MCS4 (PER ≦10%) - - -70 dBm 6) MCS5 (PER ≦10%) - - -66 dBm 7) MCS6 (PER ≦10%) - - -65 dBm 8) MCS7 (PER ≦10%) - - -64 dBm 6. Maximum Input Level (PER ≦10%) 1) IEEE802.11n HT20 @ 2.4G -20 - - dBm 2) IEEE802.11n HT20 @ 5G -30 - - dBm
Sichuan AI-Link Technology Co., Ltd. page 12 of 17 4.4 IEEE 802.11n HT40 Section: Items Contents Specification IEEE802.11n HT20 @ 2.4G IEEE802.11n HT20 @ 5G Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH3 to CH11 @ 2.4G CH38 to CH163 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark1. Power Levels (Calibrated) 1) 14dBm Target (For Each antenna port) @ 2.4G 13 15 17 dBm 2) 13dBm Target (For Each antenna port) @ 5G 13 15 17 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-21MHz - - -20 dBr 2) at fc +/-40MHz - - -28 dBr 3) at fc > +/-60MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G -10 - 10 ppm 2) IEEE802.11n HT20 @ 5G -12 - 12 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) - - -79 dBm 2) MCS1 (PER ≦10%) - - -76 dBm 3) MCS2 (PER ≦10%) - - -74 dBm 4) MCS3 (PER ≦10%) - - -71 dBm 5) MCS4 (PER ≦10%) - - -67 dBm 6) MCS5 (PER ≦10%) - - -63 dBm 7) MCS6 (PER ≦10%) - - -62 dBm 8) MCS7 (PER ≦10%) - - -61 dBm 6. Maximum Input Level(PER ≦10%) 1) IEEE802.11n HT20 @ 2.4G -20 - - dBm 2) IEEE802.11n HT20 @ 5G -30 - - dBm
Sichuan AI-Link Technology Co., Ltd. page 13 of 17 4.5 IEEE 802.11ac Section: Items Contents Specification IEEE802.11ac Mode BPSK, QPSK, 16QAM, 64QAM ,256QAM and OFDM Channel CH36 to CH165 VHT20 CH38 to CH163 VHT40 CH42 to CH157 VHT80 Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels (Calibrated) 1) 11dBm Target (For Each antenna port) 11 13 15 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz /20MHz/30MHz - - -20 dBr 2) at fc +/-21MHz /40MHz/60MHz - - -28 dBr 3) at fc +/-41MHz /80MHz/120MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -27 dB 9) MCS8 -30 dB 10) MCS9 -32 dB 4. Frequency Error -10 - 10 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) VHT20 VHT40 VHT80 1) MCS0 (PER ≦10%) - - -82 -79 -76 dBm 2) MCS1 (PER ≦10%) - - -79 -76 -73 dBm 3) MCS2 (PER ≦10%) - - -77 -74 -71 dBm 4) MCS3 (PER ≦10%) - - -74 -71 -68 dBm 5) MCS4 (PER ≦10%) - - -70 -67 -64 dBm 6) MCS5 (PER ≦10%) - - -66 -63 -60 dBm 7) MCS6 (PER ≦10%) - - -65 -62 -59 dBm 8) MCS7 (PER ≦10%) - - -64 -61 -58 dBm 9) MCS8 (PER ≦10%) - - -59 -56 -53 dBm 10) MCS9 (PER ≦10%) - - -57 -54 -51 dBm 6. Maximum Input Level(PER ≦10%) -30 - - dBm
Sichuan AI-Link Technology Co., Ltd. page 14 of 17 4.6 Bluetooth Section: Items Contents Specification BT2.1/3.0/4.0/5.0 Mode FHSS,GFSK,DPSK,DQPSK Number of Channel 79 Channels Frequency Band 2.402 GHz ~2.480GHz Min. Typ. Max. Unit Remark1. Output Power - 3 - dBm 2.Gain step 5 dB Class1 3. Receiver sensitivity (BER ≦0.1%) - -93.5 -80 dBm 4. Maximum usable signal (BER ≦0.1%) - -5 - 5. C/I co-channel (BER<0.1%) - 4 11 dB 6. C/I 1MHz (BER<0.1%) - -14 0 dB 7. C/I 2MHz (BER<0.1%) - -42 -30 dB 8. C/I≥3MHz (BER<0.1%) - -49 -40 dB 9. C/I Image channel (BER<0.1%) - -25 -9 dB 10. C/I Image 1MHz (BER<0.1%) - -50 -20 dB 11. Inter-modulation - -13 - dB 12. Out-of-band blocking 1). 30MHz to 2000MHz -10 - - dBm 2). 2000MHz to 2399MHz -27 - - dBm 3). 2498MHz to 3000MHz -27 - - dBm 4). 3000MHz to 12.75GHz -10 - - dBm 13. Modulation characteristics 1). Δf1avg 140 157 175 KHz 2). Δf2max (For at least 99.9% of all Δf2max) 115 140 - KHz 3). Δf1avg /Δf2avg 0.8 0.98 - KHz 14. ICFT -75 ±20 +75 KHz 15. Carrier frequency drift 1). One slot packet (DH1) -25 ±15 +25 KHz 2). Two slot packet (DH3) -40 ±15 +40 KHz 3). Five slot packet (DH5) -40 ±15 +40 KHz 4). Max drift rate - 6 20 KHz/50us 16. TX output spectrum(20dB bandwidth) - 922 1000 KHz 17. In-Band spurious emission 1). ±2MHz offset - -45 -20 dBm 2). ±3MHz offset - -48 -40 dBm 3). >±3MHz offset - -48 -40 dBm
Sichuan AI-Link Technology Co., Ltd. page 15 of 17 6、The connector
Sichuan AI-Link Technology Co., Ltd. page 16 of 17 7、Statement： A、CE Radiation Exposure Statement Herby, Sichuan AI-Link Technology Co., Ltd. declares that this Wireless Module&Bluetooth Module，WF-M668-UWP1 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Operation Temperature：Use the WF-M668-UWP1 in the environment with the temperature between -10℃ and 70℃ Operation Frequency range:2.400 ~ 2.4835 GHz,5.150~5.350 GHz,5.470~5.725 GHz,5.725~5.850 GHz The above frequency can be used of Europe without restriction. Max RF Output Power: 20dBm Manufacturer：Sichuan AI-Link Technology Co., Ltd. Address：Anzhou,Industrial park,Mianyang,Sichuan, China Tel: +86- 0816-2438701 Fax: +86-0816-2416943 E-mail: caixia.hu@changhong.com B、FCC Radiation Exposure Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display label referring to the enclosed module. This exterior label can use wording such as the following:” Contains Transmitter Module FCC ID: 2AOKI-WFM668UWP1 Or Contains FCC ID: 2AOKI-WFM668UWP1 when the module is installed inside another device, the user manual of this device must contain below warning statements;1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may undesired operation.2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device is intended only for OEM integrators under the followingconditions:1) The antenna must be installed such that 20 cm is maintained between the antenna and user.2) The transmitter module may not be co-located with any other transmitter or antenna. Module Antenna Type: BT: Ceramic Antenna, Wifi: Integral Antenna, ANT Gain: BT: 1dBi, 2.4G Wifi: 1dBi, 5G Wifi: 2dBi.
Sichuan AI-Link Technology Co., Ltd. page 17 of 17 C、IC Radiation Exposure Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement

Navigation menu