Siemens Canada WIN7025 Base Station Transceiver User Manual RUGGEDCOM WIN7000

Siemens Canada Limited Base Station Transceiver RUGGEDCOM WIN7000

Users Manual

RUGGEDCOM WIN7000Installation Guide9/2014FCC Statement andCautionsIntroduction 1Site and InstallationRequirements 2Installation Procedures 3Setup 4Troubleshooting 5Connector and CablePinouts AWIN7000 Specifications BList of Acronyms CWarranty DRC1062-EN-02
RUGGEDCOM WIN7000Installation Guideii
RUGGEDCOM WIN7000Installation Guide Table of ContentsiiiTable of ContentsFCC Statement and Cautions ............................................................................. vChapter 1Introduction .......................................................................................................... 11.1 About this Guide .......................................................................................................................... 11.2 Capabilities and Features ............................................................................................................. 11.3 Safety Information ........................................................................................................................ 21.3.1 General ............................................................................................................................. 21.3.2 Power Supply Requirements .............................................................................................. 21.3.3 Equipment Installation ........................................................................................................ 41.3.4 Radio Frequency (RF) Exposure ........................................................................................ 41.3.5 Lightning Protection ........................................................................................................... 41.3.6 Power Cord Protection ....................................................................................................... 41.3.7 Servicing ........................................................................................................................... 41.3.8 Antenna Grounding Requirements ...................................................................................... 51.3.9 Outdoor Grounding System ................................................................................................ 51.3.10 User Ports and Power Supply .......................................................................................... 51.3.11 Safety Hazards ................................................................................................................ 51.4 WIN7000 Physical Specifications .................................................................................................. 6Chapter 2Site and Installation Requirements ..................................................................... 72.1 Mounting Considerations .............................................................................................................. 7Chapter 3Installation Procedures ........................................................................................ 93.1 Pre-Installation Safety Instructions ................................................................................................ 93.2 Package Components and Unpacking ........................................................................................... 93.3 Installation Tools .......................................................................................................................... 93.4 Installing the Base Station .......................................................................................................... 103.4.1 Sealing Screw ................................................................................................................. 103.4.2 WIN7000 Mounting Bracket .............................................................................................. 113.4.3 Pole Mounting ................................................................................................................. 123.4.4 Wall Mounting ................................................................................................................. 133.4.5 Tower Mount ................................................................................................................... 14
Table of ContentsRUGGEDCOM WIN7000Installation Guideiv3.4.6 Power and Cable Connections ......................................................................................... 153.4.6.1 PEC (Copper) Type Base Station .......................................................................... 153.4.6.2 SFA (Optical) Type Base Station ............................................................................ 173.4.6.3 SFD Type Base Station ......................................................................................... 183.4.7 Grounding the Device ...................................................................................................... 213.4.8 Installing the GPS Antenna .............................................................................................. 213.4.9 2.3GHz Band Cavity Filters Installation ............................................................................. 223.5 Weatherproofing ......................................................................................................................... 303.5.1 Weatherproofing Cable Connections ................................................................................. 313.6 Hazardous Location Information .................................................................................................. 343.7 Hazardous Location Installation ................................................................................................... 34Chapter 4Setup .................................................................................................................. 374.1 Connecting to the WIN7000 Web Interface .................................................................................. 37Chapter 5Troubleshooting .................................................................................................. 415.1 No IP connectivity ...................................................................................................................... 415.2 No Serial Connection ................................................................................................................. 41Appendix AConnector and Cable Pinouts ............................................................................ 43A.1 Power and Ethernet Cable Pinouts ............................................................................................. 43A.2 Console Cable Pinouts ............................................................................................................... 44Appendix BWIN7000 Specifications ..................................................................................... 45Appendix CList of Acronyms ................................................................................................ 47Appendix DWarranty ............................................................................................................. 49
RUGGEDCOM WIN7000Installation Guide FCC Statement and CautionsvFCC Statement and CautionsFederal Communications Commission Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferencewhen the equipment is operated in a commercial environment. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instruction manual, may causeharmful interference to radio communications. Operation of this equipment in a residential area is likely to causeharmful interference in which case the user will be required to correct the interference at his own expense.CAUTION!Caution: ServiceThis product contains no user-serviceable parts. Attempted service by unauthorized personnel shallrender all warranties null and void.Changes or modifications not expressly approved by SIEMENS could invalidate specifications,test results, and agency approvals, and void the user’s authority to operate the equipment.CAUTION!Caution: Physical AccessThis product should be installed in a restricted access location where access can only be gained byservice personnel or users who have been instructed about the reasons for the restrictions applied tothe location and about any precautions that shall be taken; and access is through the use of a tool orlock and key, or other means of security, and is controlled by the authority responsible for the location.
RUGGEDCOM WIN7000Installation Guide FCC Statement and Cautionsvi
RUGGEDCOM WIN7000Installation GuideChapter 1IntroductionAbout this Guide 1IntroductionThe WIN7000 High Power Base Station is a member of the RUGGEDCOM WIN family, a line of mobile WiMAXbroadband wireless access systems based on the 802.16e mobile WiMAX standard. RUGGEDCOM systems aredesigned for robustness and simplicity, offering feature-rich services with low deployment and operation costs.The WIN7000 is a member of a line of mobile WiMAX broadband wireless access systems based on the 802.16emobile WiMAX standard. These systems are designed for robustness and simplicity, offering feature-rich serviceswith low deployment and operation costs.The WIN7000 is a cost-effective solution for wireless access services, designed for point-to-multipoint broadbandwireless access applications in varying conditions and locations. It is a one-sector base station.The base station communicates with fixed and mobile subscriber units, according to defined service criteria andcustomer service level agreements. The WIN7000 also connects to the service provider backbone, supportingend-to-end Quality of Service (QoS) requirements.The system uses OFDMA radio technology, providing robustness in adverse channel conditions and enablingNon-Line-Of-Sight (NLOS) operation. This improves coverage and maintains a high level of spectral efficiency.Modulation and coding are continuously adapted to prevailing link conditions, ensuring an optimal balancebetween robustness and efficiency. The use of STC/MRC and MIMO radio technologies optimizes linkperformance, ensuring enhanced bandwidth and service coverage.The RUGGEDCOM WIN7000 is a full outdoor base station, designed for easy installation and mounting on poles,street lamps, towers, or walls. The WIN7000 can be equipped with copper or fibre network interfaces for flexibleintegration into the operator’s backbone.The WIN7000 is supported by RUGGEDCOM NMS, Siemens’s comprehensive Network Management System.Section 1.1About this GuideThis installation guides describes the installation of the WIN7000 High Power Base Station.This guide is intended for use by base station installers and operators, and assumes readers have a workingknowledge of WiMAX technologies and procedures. While some safety precautions are reviewed here, itis assumed that installers are trained in safe installation practices. Users unfamiliar with safe installationprocedures, WiMAX technologies, and service procedures should not rely on this manual for comprehensiveguidance.Section 1.2Capabilities and FeaturesThe WIN7000 provides the full base station functionality necessary for serving a single sector:• Supported Frequency Bands: 5251, 5151, 7251• All-outdoor, single-box installation• IEEE802.16e Wave2 Standard Compliance
Chapter 1IntroductionRUGGEDCOM WIN7000Installation Guide2 Safety Information• Backbone Ethernet connectivity via a 10/100 Base-T network interface• Fixed and mobile CPE support• 3.5 MHz, 5MHz, 7MHz and 10MHz channel bandwidth support• MIMO (2×2) support• Various Radio Frequency (RF) options, including 1.x, 2.x and 3.x GHz band support• Traffic classification and connection establishment initiation• Quality of Service (QoS) management• Alarm management• Internal SNMP agent, enabling extensive In-Band (IB) management of the base station and its registered CPEs• R6 interface to ASN-GW profile C• Power requirement: 48VDCSection 1.3Safety InformationSection 1.3.1General• Read this user manual and follow all operating and safety instructions.• The base station and antenna must be installed by a professional installer.• Do not exceed the described limits.Section 1.3.2Power Supply Requirements• The power supply unit should be a Class 2 power supply, safety-certified according to national codes.• Maximum output current should not exceed 5A.• Maximum output voltage of the power supply should not exceed 60VDC.• Minimum output voltage should not be below 42VDC.• The disconnecting device is defined as the following:▪ When connected to an AC/DC power supply, the appliance coupler of the AC/DC power supply is regardedas the main disconnecting device for the base station.▪ When connected to a DC battery power supply, a double pole circuit breaker, rated 10A 60VDC, is regardedas the main disconnecting device for the base station.The unit is considered to be connected to a centralized DC power system, therefore the power line should begrounded. The unit should be permanently connected to ground with 16AWG cable or less. See the figures belowfor two methods of power grounding (from the UL 60950-1 standard; according to UL 60950-22). When the unit isconnected to a centralized DC Power System, the "+" side of the supply should be grounded, as per UL60950-1and UL 60950-22 requirements.
RUGGEDCOM WIN7000Installation GuideChapter 1IntroductionPower Supply Requirements 3Figure 1: Typical Centralized DC Power System, Plant and Distribution Source-Grounded DC Power SystemFigure 2: Typical Centralized DC Power System, Plant and Distribution DC Power System Grounded at EquipmentLocation
Chapter 1IntroductionRUGGEDCOM WIN7000Installation Guide4 Equipment InstallationSection 1.3.3Equipment InstallationInstall the equipment in accordance with the electrical code relevant to the country of installation, such as theNational Electrical Code (NEC), ANSI/NFPA 70; the Canadian Electrical Code (CEC), Part 1, CSA C22.1;and when applicable, the National Electrical Safety Code IEEE C2. Unless marked or otherwise identified, theStandard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75, also applies.Section 1.3.4Radio Frequency (RF) ExposureThe WIN7000 is compliant with the requirements set forth in CFR 47, section 1.1307, addressing RadioFrequency (RF) exposure from radio frequency devices as defined in OET Bulletin 65. The emitted radiationshould be as little as possible. To achieve minimum RF exposure, install the WIN7000 when it is configured notto transmit and set it to operational mode remotely, rather than enabling transmission by the installer on-site. Formaintenance of the WIN7000, or other operations which require RF exposure, the exposure should be minimizedin time and according to the regulations set by the FCC or the regulations relevant to the country of installation.Section 1.3.5Lightning ProtectionWARNING!When the WIN7000 is installed in an outdoor location, all indoor components (such as Ethernet andpower supply) should be connected through a lightning protector.Lightning protection protects people and equipment located indoors from lightning that might strikethe WIN7000 or its outdoor cables. Therefore, install the lightning protector device indoors, as closeas possible to the point where the cables enter the building. The lightning protector can also beinstalled outdoors as long as the cables that lead indoors are well protected from lightning between theprotector and the building entrance.Section 1.3.6Power Cord ProtectionRoute all power supply cords so that people cannot walk on them or place objects on or against them. Walking onthe cords or placing objects on or against the cords can damage the cords.Section 1.3.7ServicingDo not open the cover of this product to attempt service unless instructed by a RUGGEDCOM certifiedtechnician. Refer all repairs to qualified service personnel. Removing the covers or modifying any part of thisdevice voids its warranty.
RUGGEDCOM WIN7000Installation GuideChapter 1IntroductionAntenna Grounding Requirements 5Siemens does not endorse or support the use of proprietary third-party outdoor cable assemblies not supplied bySiemens.WARNING!Keep away from electric power lines.You can be killed if the antennas are in close proximity to electric power lines. Carefully read andfollow all instructions in this manual. By nature of the installation, you may be exposed to hazardousenvironments and high voltage. Use caution when installing the outdoor system.Section 1.3.8Antenna Grounding RequirementsThe antenna installation must be as per Article 810 of the NEC. Of particular note is the requirement that thegrounding conductor not be less than 10 AWG (Cu). The scheme should be either in accordance with UL 96 and96A Lightning Protection Components and Installation Requirements for Lightning Protection Systems, or testedin accordance with UL 50 and UL 497.Section 1.3.9Outdoor Grounding SystemWARNING!Verify that the base station is grounded.The system must be properly grounded to protect against power surges and accumulated staticelectricity. It is the installer’s responsibility to install this device in accordance with the local electricalcodes.Section 1.3.10User Ports and Power SupplyIf the length of outdoor exposed communication lines is greater than 40 m (140 feet), these lines must be treatedas TNV-1 circuits. The installer must ensure that the power supply and network ports are designed for fullcompliance with the TNV-1 telecommunication network.Section 1.3.11Safety HazardsWARNING!Installing the WIN7000 can pose a serious hazard. Be sure to take precautions to avoid the following:• Exposure to high voltage lines during installation• Falling when working at heights or with ladders• Injuries from dropping tools
Chapter 1IntroductionRUGGEDCOM WIN7000Installation Guide6 WIN7000 Physical Specifications• Contact with AC wiring (power system connection)WARNING!To reduce the risk of fire, use only 26AWG or larger telecommunication line cord.Section 1.4WIN7000 Physical SpecificationsThe WIN7000 is packed in a waterproof metal housing. A mounting bracket and mounting kit allows for pole orwall installation. The assembled unit weighs approximately 15kg.For information on the WIN7000 wiring connections, see Section 3.4.6, “Power and Cable Connections”.Figure 3: WIN7000 Dimensions
RUGGEDCOM WIN7000Installation GuideChapter 2Site and Installation RequirementsMounting Considerations 7Site and InstallationRequirementsSection 2.1Mounting ConsiderationsWhen choosing a mounting location, consider the available mounting structures and antenna clearance. Toprovide better weather protection, the WIN7000 should be mounted with the connection panel facing downwards.The base station is equipped with a mounting kit, which allows several mounting options:• Poles: Attach the WIN7000 to any pipe or pole with diameter 1.75" to 10".• Towers and Walls: Attach the WIN7000 to any tower or wall that can support the load of the unit.The following antenna options are available:• 2 × omni-directional antenna• External sector dual slant ±45º antenna• Two separate antennasBefore mounting the antennas, conduct a site survey to determine the optimal position for the antennas. Observethe following guidelines:• Mount the antennas at the highest point possible. Reception will increase according to the height of theantennas.• Mount the antennas in a place with as few obstacles as possible between the antennas and the plannedservice area.• To avoid interference, mount the antennas and base station as far as possible from antennas of other devicesand other base stations.• To keep the cable from the base station to the antenna as short as possible, mount the antennas as closeas possible to the base station. Using a cable longer than 2 meters will result in greater loss and moreinterference, as the cable will act as an antenna.• Do not point the antennas directly at populated areas, and locate the antennas at least 3.6 m from people andpublic areas.• Mount the antennas and base station in a place that allow for maintenance access to the unit.• Mount the GPS antenna in a position where the whole sky is visible to the antenna. If the base station ismounted on a wall and the GPS antenna is mounted on top of the base station, only half of the sky will bevisible to the antenna. This may not be enough for proper operation.
RUGGEDCOM WIN7000Installation GuideChapter 2Site and Installation RequirementsMounting Considerations 8
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresPre-Installation Safety Instructions 9Installation ProceduresSection 3.1Pre-Installation Safety InstructionsWARNING!Installing the WIN7000 can pose a serious hazard. Be sure to take precautions to avoid the following:• Exposure to high voltage lines during installation• Falling when working at heights or with ladders• Injuries from dropping tools• Contact with AC wiring (power system connection)Section 3.2Package Components and UnpackingCheck that the package contains:• WIN7000.• GPS antenna• 2 × RF cables 1.6 m for connection to antenna• Pole / wall mount kit• WINPS 48V power supply for Copper and SFA configurationSection 3.3Installation Tools• Phillips screwdriver• Wrench or socket set• Drill and 5/16" drill bit• Self-fusing electrical tape or insulating putty suitable for use in the unit’s installation environment
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide10 Installing the Base StationSection 3.4Installing the Base StationWARNING!The equipment should be installed in compliance with the National Electrical Code (NEC), ANSI/NFPA 70, the Canadian Electrical Code (CEC), Part 1, CSA C22.1; and when applicable, the NationalElectrical Safety Code IEEE C2. Unless marked or otherwise identified, the Standard for the Protectionof Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.The following components are required for the installation:• Mounting bracket• WIN7000• RF antennas• GPS antenna• Power supply• Ground, data, and power cablesTo install the WIN7000, follow these general steps:1. Install the mounting bracket at the chosen location.2. Install the antennas.3. Prepare the grounding cables.4. Lay out the connection cables.5. Mount the power supply.6. Mount the base station to the mounting bracket.7. Connect all cables to the WIN7000 and seal connections with suitable electrical tape or putty.Section 3.4.1Sealing ScrewCAUTION!Do not attempt to open the sealing screw on the bottom side of base-station. Opening the screw willbreak the sealing and will cause the moisture getting into the base-station.
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresWIN7000 Mounting Bracket 11Figure 4: Location of the Sealing ScrewSection 3.4.2WIN7000 Mounting BracketThe mounting bracket is used for both pole- and wall-mount installations.Figure 5: Mounting Bracket
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide12 Pole MountingSection 3.4.3Pole MountingFigure 6: WIN7000 Pole Mounting DiagramTable: WIN7000 Pole Mount Parts ListItem Quantity Description1 1 Mounting brackets2 1 WIN70003 2 Fastening brackets4 4 Screw 5/16" hex cap × 6"5 8 Nut NF 16 hex6 10 Washer flat 5/16"7 10 Washer spring 5/16"8 4 Screw NC 1/4" × 1/2" hex9 4 Washer flat NC 1/4"10 4 Washer spring NC 1/411 1 Pole12 2 Bolt NC 1/4"13 2 Screw NC 5/16" × 1/2"14 1 Mounting Upper Bracket
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresWall Mounting 13Procedure: Installing the WIN7000 on a Pole1. Select a mounting location on the pole.2. Assemble the fastening brackets to the mounting bracket using the 5/16" × 6" hex cap screws (Item 4), NF16 hex nuts (Item 5), 5/16" flat washers (Item 6), and 5/16" spring washers (Item 7).3. Lift the base station by the eye bolts and secure it to the mounting bracket. At the top of the unit andmounting bracket, use NC 1/4" × 1/2" hex screws (Item 8) and NC 1/4" flat washers (Item 9). At the bottom ofthe unit and mounting bracket, use 5/16" flat washers (Item 6), 5/16" spring washers (Item 7), and NC 5/16" ×1/2" screws (Item 13).4. Complete the wiring connections.NOTESeal all connectors with self-fusing electrical tape or insulating putty suitable for use in the unit’sinstallation environmentSection 3.4.4Wall MountingFigure 7: WIN7000 Wall Mounting DiagramTable: WIN7000 Wall Mount Parts ListItem Quantity Description1 1 Mounting brackets
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide14 Tower MountItem Quantity Description2 1 WIN70003 4 Screw NC 1/4" × 1/2" hex4 4 Washer flat NC 1/4"5 4 Washer spring NC 1/4"6 2 Bolt NC 1/4"7 4 Screw 5/16" hex cap × 2"8 4 Washer flat 5/16"9 4 Washer spring 5/16"10 4 Dowel 5/16"11 1 Mounting upper bracketProcedure: Installing the WIN7000 on a Wall1. Select a mounting location.2. Place the mounting bracket on the wall and mark the location of the four mounting holes, two at the top andtwo at the bottom.3. With a 5/16" drill bit suitable for the wall material, drill holes at the marked locations.4. Insert the 5/16" dowels (Item 10) into the holes.5. Assemble four 5/16" flat washers (Item 8), four 5/16" spring washers (Item 9), and four 5/16" × 2" hex capscrews (Item 7) into the holes on the mounting bracket.6. Secure the mounting bracket to the wall.7. Lift the base station by the eye bolts and secure it to the mounting bracket. At the top of the unit andmounting bracket, use NC 1/4" × 1/2" hex screws (Item 3), NC 14" flat washers (Item 4), and NC 1/4" springwashers (Item 5).8. Complete the wiring connections.NOTESeal all connectors with self-fusing electrical tape or insulating putty suitable for use in the unit’sinstallation environment. For more information on sealing the connectors, see Section 3.5,“Weatherproofing”.Section 3.4.5Tower MountFollow the same procedure as for wall mounting; see Section 3.4.4, “Wall Mounting”. Ensure that the tower canhold the load of the base station.
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresPower and Cable Connections 15Section 3.4.6Power and Cable ConnectionsThere are three power connection options for the WIN7000, which are described in the following sections. Thepower connection options are as follows:• PEC (Copper) Type Base Station• SFA (Optical) Type Base Station• SFD Type Base StationThe WIN7000 can be equipped with copper or fiber Ethernet connections. These copper and fiber port optionsare described in Section 3.4.6.1, “PEC (Copper) Type Base Station” and Section 3.4.6.2, “SFA (Optical) TypeBase Station”.Use the following tools to fasten or loosen the connectors:Description Manufacturer Tool Number Type Torque Connector NameType-N 1 Nm VariantWrench, 20 mmTessco 13055 Hexagon 1.35 N·m (11.9 lbf-in) ANT1/ANT2Modular PlugsConnector RemovalTool, BNC/TNC, 12"Ideal 35-042 Round 0.56 N·m (4.9 lbf-in) GPSCurved Jaw LockingPlierIrvin 502L3 Curved 4 N·m (35.4 lbf-in) DC/ETHSection 3.4.6.1PEC (Copper) Type Base StationThe power system is supplied by Siemens (WINPS).To connect the power system and cables, do the following:Procedure: Connecting the Power System and Cables1. Connect the supplied combo (DC + Ethernet cable) to the power system (WINPS) port labeled DC + ETH.2. Connect the other end to port 6 on the WIN7000 unit as shown in Figure 9.3. Connect the Ethernet input to the 10/100 Base-T connector on the power system.The following figure shows the physical connection between the WIN7000, the power system, and the AC powersource.
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide16 PEC (Copper) Type Base StationFigure 8: Base Station Power ConnectionThe following figure and table show the ports, connectors and cables.Figure 9: Copper Ethernet Port OptionTable: WIN7000 Connectors and CablesPortNumberConnectorName Connector Type Cable Type Function Connected to1 ANT1 N type Female RG 6 or 9Connected to externalantenna or omni-directionalantennaAntenna2 GND Adjustable nut #10 AWG barecopper wire Grounding Central earth ground, toweror pole chassis3 GPS TNC Female Proprietary cable GPS signal GPS antenna4 Not used5 Console 3-pin UART 3P toDB9F"Low level CLI fortechnicians PC6 DC/ETH DC + ETH Proprietary cable 48 VDC/ Return / 5A +Ethernet Cat5Power supply + Network/Router/Switch
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresSFA (Optical) Type Base Station 17PortNumberConnectorName Connector Type Cable Type Function Connected to7 ANT2 N type Female RG 6 or 9Connected to externalantenna or omni-directionalantennaAntennaSection 3.4.6.2SFA (Optical) Type Base StationThe power system is supplied by Siemens (WINPS).To connect the power system and cables, do the following:Procedure: Connecting the Power System and Cables1. Connect the supplied DC cable to the power system (WINPS) port labeled DC+ETH.2. Connect the other end of the cable to the DC/ETH port on the WIN7000 shown as port 4 in Figure 11.3. Connect the optical cable to the F/O connector on the WIN7000 (for more information, see Figure 11).4. Connect the optical cable to the network switch.NOTEThe fiber optic standard is Gigabit Ethernet 1000 Base-LX.The following figure shows the physical connection between the WIN7000, the power system, and the AC powersource.Figure 10: Base Station Power ConnectionThe following figure and table show the ports, connectors and cables.
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide18 SFD Type Base StationFigure 11: Fiber Optic Ethernet Port OptionTable: WIN7000 Connectors and CablesPortNumberConnectorName Connector Type Cable Type Function Connected to1 ANT1 N type Female RG 6 or 9Connected to externalantenna or omni-directionalantennaAntenna2 GND Adjustable nut #10 AWG barecopper wire Grounding Central earth ground, toweror pole chassis3 GPS TNC Female Proprietary cable GPS signal GPS antenna4 DC/ETH or DC DC/ETH or DC Proprietary cable48 VDC / Return / 5A +Ethernet Cat5Or 48 VDC / Return / 5APower supply +Network/Router/SwitchOr Power supply5 Console 3-pin UART 3P toDB9F"Low level CLI fortechnicians PC6 F/O Optic SM Mini LCFiber Optic SMOFNR I/O withIndustrial Plug,ODVA CableOptic 100M/1GMbit Network/Router/Switch7 ANT2 N type Female RG 6 or 9Connected to externalantenna or omni-directionalantennaAntennaSection 3.4.6.3SFD Type Base StationThe power system is supplied by the operator.To connect the power system and cables, do the following:Procedure: Connecting the Power System and Cables1. Connect the power system DC output to the supplied connector.
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresSFD Type Base Station 192. Connect the other end (open end) of the supplied cable to the operator’s power system (according to thelabelling on the cable and the following tables). For more information, see Figure 12 and Figure 13, whichshow +48V and -48V configurations.Figure 12: Positive 48V ConfigurationFigure 13: Negative 48V Configuration3. Connect the optical cable to the F/O connector on the WIN7000 (for more information, see Figure 14).
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide20 SFD Type Base StationFigure 14: Fiber Optic Ethernet Port Option4. Connect the optical cable to the network switch (for more information, see Figure 15).NOTEThe fiber optic standard is Gigabit Ethernet 1000 Base-LX.Figure 15: Base Station Power ConnectionTable: +48 VDC Power SystemSupplied Cable Power Supply Note-48VDC -48VDC GND+48VDC +48VDC/ GND “HOT Line”GND -48VDC/ GND Connect -48V and GNDTable: -48 VDC Power SystemSupplied Cable Power Supply Note-48VDC -48VDC “HOT Line”+48VDC +48VDC/ GND GND
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresGrounding the Device 21Supplied Cable Power Supply NoteGND +48VDC/ GND Connect +48V and GNDSection 3.4.7Grounding the DeviceTo ground the device, do the following:Procedure: Grounding the Device1. Assemble the ground connection as shown:65234321Figure 16: Ground Cable Assembly1. Ground Stud 2. Flatwasher 3. External Tooth Lockwasher 4. 10 AWG Isolated Ring 5. Nut 6. 10 AWG Ground Wire2. Using a 1/4" square drive socket, torque the nut to 8.5 N·m (75 lbf-in).Section 3.4.8Installing the GPS AntennaTo install the GPS antenna, do the following:Procedure: Installing the GPS Antenna1. Mount the GPS antenna as shown in Figure 17.
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide22 2.3GHz Band Cavity Filters InstallationFigure 17: Installing the GPS Antenna2. Connect the GPS cable (TNC female connector) between the antenna and the base station.Section 3.4.92.3GHz Band Cavity Filters InstallationTo comply with FCC limits, the unit must be connected to cavity filters (for full-power configuration only).Follow these steps to assemble the 2.3GHz cavity filters and connect them to the base station antennas.There are two types of cavity filters: one for A+B band, and one for C+D band.Figure 18: A+B Band Cavity Filter
RUGGEDCOM WIN7000Installation GuideChapter 3Installation Procedures2.3GHz Band Cavity Filters Installation 23Figure 19: C+D Band Cavity FilterThe cavity filter mounting kit provides the following mounting options:• Pole mounting: Attach the filters to any pipe or pole with a diameter of 1.75" to 10".• Wall mounting: Attach the filters to any wall that can support the weight of the filters and mounting bracket.Procedure: Assembling and Connecting Cavity Filters1. Position the cavity filters (Item 1 × 2) on the baseplate (Item 2).2. Secure the filters to the baseplate using Flat Washer (M5), Spring Washer (M5), and Screw (M5) (Items 3, 4,and 5 × 8).
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide24 2.3GHz Band Cavity Filters InstallationFigure 20: A+B Band Cavity Filters Mounted on Baseplate
RUGGEDCOM WIN7000Installation GuideChapter 3Installation Procedures2.3GHz Band Cavity Filters Installation 25Figure 21: C+D Band Cavity Filters Mounted on Baseplate3. Position the adaptor plate (MT-120018) on the baseplate in the position shown in Figure 22.4. Secure the adaptor plate using Flat Washer (M5), Spring Washer (M5), and Hex Nut (M5) (Items 2, 3, and 4× 4).
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide26 2.3GHz Band Cavity Filters InstallationFigure 22: Adaptor Plate Mounted on Baseplate5. Insert the adaptor bracket into the adaptor plate.6. Secure the adaptor bracket with Set Screw (M5) as shown in Figure 23.
RUGGEDCOM WIN7000Installation GuideChapter 3Installation Procedures2.3GHz Band Cavity Filters Installation 27Figure 23: Adaptor Bracket Mounted to Adaptor Plate7. Attach the wall mount bracket to the adaptor bracket.8. Secure the wall mount bracket with Flat Washer (M5), Spring Washer (M5), and Set Screw (M5) as shown inFigure 24.Figure 24: Wall Mount Bracket Assembly
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide28 2.3GHz Band Cavity Filters InstallationNOTEFor the wall mounting option, assembly of the cavity filter mounting bracket is now complete.Mount the assembly to the wall and complete the antenna connections described in Step 11.9. For pole mounting, attach the pole mounting bracket to the wall mounting bracket as shown in Figure 25.10. Secure the pole mounting bracket with Flat Washer (M5), Spring Washer (M5), and Set Screw (M5) asshown in Figure 25.Figure 25: Pole Mount Bracket Assembly11. Connect the RF cables to the cavity filters and the base station. Connect cavity filter IN to the base station.Connect cavity filter OUT to the antenna.
RUGGEDCOM WIN7000Installation GuideChapter 3Installation Procedures2.3GHz Band Cavity Filters Installation 29Figure 26: A+B Band Cavity Filter Antenna Connections
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide30 WeatherproofingFigure 27: C+D Band Cavity Filter Antenna ConnectionsSection 3.5WeatherproofingIt is extremely important to weatherproof all outdoor cable connections. Weatherproofing the connections at theoutdoor unit and antennas prevents corrosion, prevents water from interfering with the connection, and helps tokeep the connection tight. Because cables also carry DC current, the need for proper weatherproofing cannot beoverstated.We recommend the use of sealing tapes designed for outdoor use:• 3M™ Scotch® Super 88 Electrical Tape• Heavy-duty weather-, abrasion-, and UV-resistant rubber splicing tape or self-amalgamating tapeRubber mastic putty or duct sealing putty must also be used to complete the weatherproofing where needed.We do not recommend silicon seal or glue. These materials are difficult to apply accurately and are difficult toremove. Do not use PVC tape.
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresWeatherproofing Cable Connections 31Section 3.5.1Weatherproofing Cable ConnectionsMost outdoor unit, antenna, or cable problems are caused by coaxial cable connections loosened by vibration,allowing moisture to penetrate the connector interface. We recommend that all outdoor unit-to-cable connectionsbe weatherproofed using a procedure similar to the one described below.This method of weatherproofing must be completed on all external connections. If surge arrestors are used, allthe associated connections and arrestors must be completely wrapped with splicing tape or self-amalgamatingtape.NOTEBefore waterproofing, ensure all connectors are correctly tightened. Ensure the connector and cablesare free of foreign substances such as oil, water, grease, and dirt. Ensure that the cable extends belowthe connector to which it is attached, providing a path for water to follow away from the connecteddevice.Procedure: Weatherproofing Cable Connectors1. Begin to wrap the rubber-splicing or self-amalgamating tape. Start as close to the equipment body aspossible. Stretch and wind the tape around the connector housing, ensuring there are no gaps in the tape.Figure 28: Wrapping the Connector with Rubber-splicing or Self-amalgamating Tape2. Tightly wrap the connector and the cable. Overlap the tape, without gaps, all the way along the connector.Continue wrapping the tape 25 mm (1") onto the cable.
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide32 Weatherproofing Cable ConnectionsFigure 29: Wrapping the Cable with Rubber-splicing or Self-amalgamating Tape3. For UV protection of the rubber splicing tape, wrap two layers of electrical tape on top of the rubber splicingtape.Figure 30: Wrapping the Connector with Electrical Tape4. Work mastic putty or duct sealing putty between the connector and the body of the radio or antenna. Ensurethe putty fills any gaps not covered by the tape.
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresWeatherproofing Cable Connections 33Figure 31: Sealing Gaps with Putty5. Apply two layers of electrical tape over the rubber splicing tape for UV protection.Figure 32 and Figure 33 show the base station connectors wrapped with splicing and electrical tape, before theapplication of mastic or duct sealing putty.Figure 32: Wrapped Connectors before the application of Weathproofing Putty
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide34 Hazardous Location InformationFigure 33: Detail of Wrapped ConnectorsWARNING!Assembly without waterproof sealing tape or removing the waterproof sealing tape from this devicevoids its warranty.Section 3.6Hazardous Location InformationThe following is the hazardous location information for this equipment:nA IIC T4 GC X II 3GRating: 48VDC,4AClass I Division 2 Groups A,B,C,DT4Section 3.7Hazardous Location InstallationHazardous Location ConsiderationsThis equipment is suitable for use in Class 1, Division 2, Groups A, B, C, D or non-hazardous locations only. Thefollowing ATTENTION statement applies to use in hazardous locations.WARNING!EXPLOSION HAZARD• Substitution of components may impair suitability for Class I, Division 2• Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
RUGGEDCOM WIN7000Installation GuideChapter 3Installation ProceduresHazardous Location Installation 35Environnements DangereuxCet équipement est conçu pour être utilisé dans des environnements de Classe 1 ,Division 2, Groupes A, B, C, Dou non dangereux. La mise en garde suivante s’applique à une utilisation dans des environnements dangereux.WARNING!RISQUE D’EXPLOSION• La substitution decomposants peut rendre ce matériel inacceptable pour les emplacements deClasse I, Division 2.• Avant de déconnecter l’equipment, couper le courant ou s’assurer que l’emplacement est désignénon dangereux.This equipment is suitable for use in Class 1, Division 2, Groups A, B, C, D hazardous locations when installedusing the Class 1, Division 2 installation kit (P/N MKIT0109).Contents of the Class 1, Division 2 Installation Kit:• WIN1212 Surge Suppression Unit• DC cable for connection between the power supply unit (PSU) and the WIN1212 unitTo install the equipment in a hazardous location, do the following:1. Connect a DC cable between the PSU and WIN1212 unit.WIN1212Figure 34: Complete Class 1 Division 2 Installation Kit2. Connect a Category 5e cable between the WIN1212's Data and Power Output connections and the basestation. For more information, refer to the RUGGEDCOM WIN1210/1212 Installation Guide.3. Connect a Category 5e cable between the Ethernet switch and the WIN1212's Data Input port.
Chapter 3Installation ProceduresRUGGEDCOM WIN7000Installation Guide36 Hazardous Location Installation4. Connect the AC open-ended cable to the PSU.CAUTION!The power supply AC cord should be 3 wires, 18 AWG minimum, with a length of less than 4.5 m, andsafety certified according to national rules.
RUGGEDCOM WIN7000Installation GuideChapter 4SetupConnecting to the WIN7000 Web Interface 37SetupThe initial setup procedure consists of:• Configuring the computer’s network parameters and connecting to the WIN7000 Web interface• Verifying IP connectivitySection 4.1Connecting to the WIN7000 Web InterfaceThis section describes how to configure the network parameters in Microsoft Windows so you can connect acomputer to the WIN7000. For instructions on how to configure the network parameters for other operatingsystems, refer to your operating system documentation.Before beginning, ensure that the base station is connected to the Power over Ethernet (PoE) power adaptor andthat power is applied.Follow these steps connect a computer to the WIN7000 Web interface:Procedure: Connecting a computer to the base station1. Ensure that the PoE adaptor is connected to the base station. Connect the computer’s Ethernet port to thePoE adaptor’s Ethernet port.2. On the computer, click Start and select Control Panel.3. In the Control Panel, select Network and Internet Connections.4. Select Network Connections and then double-click Local Area Connection. The Local Area ConnectionsProperties dialog appears with the General tab selected.
Chapter 4SetupRUGGEDCOM WIN7000Installation Guide38 Connecting to the WIN7000 Web InterfaceFigure 35: Microsoft Windows Local Area Connection Properties dialog box5. In the Items list, select Internet Protocol (TCP/IP) and click the Properties button. The Internet Protocol(TCP/IP) Properties dialog appears.6. Assign your computer the IP address 192.168.100.99 and the subnet 255.255.255.0.Figure 36: Microsoft Windows Internet Protocol (TCP/IP) Properties dialog box7. On the Internet Protocol (TCP/IP) Properties dialog, click OK. On the Local Area Connection Propertiesdialog, click Close.8. Launch your web browser and type https://192.168.100.100 in the address field.
RUGGEDCOM WIN7000Installation GuideChapter 4SetupConnecting to the WIN7000 Web Interface 39NOTEFor information on browser versions and compatibility, refer to the release notes for your softwareversion.9. The Login window appears. Enter your user name and password and click Log In. The WIN7000 webinterface appears.Figure 37: WIN7000 Web Interface: General Status page
RUGGEDCOM WIN7000Installation GuideChapter 4SetupConnecting to the WIN7000 Web Interface 40
RUGGEDCOM WIN7000Installation GuideChapter 5TroubleshootingNo IP connectivity 41TroubleshootingSection 5.1No IP connectivityIf there is no IP connectivity between the WIN7000 unit and the NMS, perform the following steps:1. Connect the the computer and the WIN7000 Console connector (serial connection), located on the unit’sbottom panel.2. In the terminal, type showIPAddr and press Enter. The base station’s IP address will be displayed.3. Ping the WIN7000 unit address.4. If connectivity is still not established, contact Siemens customer support.Section 5.2No Serial ConnectionIf there is no serial connection when using the serial cable, perform the following:1. Verify IP connectivity using a ping to the WIN7000 unit IP address.2. If there is no IP connectivity, verify the power connections.3. If the power connections are okay and there is still no serial connection or IP connectivity, contact Siemenscustomer support.
RUGGEDCOM WIN7000Installation GuideChapter 5TroubleshootingNo Serial Connection 42
RUGGEDCOM WIN7000Installation GuideAppendix AConnector and Cable PinoutsPower and Ethernet Cable Pinouts 43Connector and Cable PinoutsPower and Ethernet Cable PinoutsThe pinout of the power cable is shown below:Figure 38: WIN7000 Power Cable PinoutTable: WIN7000 Power Cable PinoutPin Number TypeA NCB NCC +TX EthernetD - TX EthernetE +RX EthernetF - RX EthernetG NCH NCJ NCK 48VDC (RTN)L 48VDC (+)M Ethernet GND
Appendix AConnector and Cable PinoutsRUGGEDCOM WIN7000Installation Guide44 Console Cable PinoutsConsole Cable PinoutsNOTEIn normal operation, the console connector should remain closed and should only be used by anauthorized technician.The console connection is a 3-pin female connector, based on the RS-232 serial standard. The port provides astandard terminal connection through which a technician can configure and monitor the base station through itscommand line interface (CLI).• Cable type: 3 wire 28AWG• Cable connectors: proprietary 3 pin console connector; DBF9• Cable length: 2m• The cable is supplied by Siemens.Figure 39: 3-pin Console Connector PinoutFigure 40: DB9F Console Connector PinoutTable: WIN7000 Console Connector Pinout3-Pin Connector Pin Number DB9F Connector Pin Number Connection1 2 TX3 3 RX4 5 GND
RUGGEDCOM WIN7000Installation GuideAppendix BWIN7000 Specifications45WIN7000 SpecificationsRadio and Modem:• Frequency, by Base Station model number:▪ WIN7023: 2300 MHz to 2400 MHz▪ WIN7025: 2496 MHz to 2690 MHz▪ WIN7035: 3400 MHz to 3600 MHz▪ WIN7015: 1400 MHz to 1520 MHz▪ WIN7018: 1800 MHz to 1830 MHz• IEEE802.16-2005 (16e OFDMA)• WiMAX Forum Wave 2 Profile• Time Division Duplex (TDD)• Channel Bandwidth (MHz) 3.5, 5, 7, 10• Frequency Resolution 0.25 MHz• Diversity Support 2x2, STC/MIMO-SM• FEC Convolution Code and Turbo Code• Transmit Power Control• Output Power (average) 2 X 36 dBm• Modulation 512/1024 FFT points; QPSK, 16QAM, 64QAMRadio Interfaces:• Number of Antennas: 2• Antenna Connectors 2 × N-Type, 50 ohm• Integrated or External Sector or Omni Antenna• Built-in GPS includedNetwork Interfaces:• 10/100BaseT Half/Full Duplex IEEE 802.3 CSMA/CD• ASN GW Compatibility WiMAX Forum R6, Profile C• Compatible with Cisco and WiChorus ASN-GW• Fiber Optic (Optional)Configuration and Management:• Web GUI• Management SNMP• SNMP Agent SNMP ver 2 client/v3• Software Upgrade via FTP, SFTP• Remote Configuration via FTP, SFTP
Appendix BWIN7000 SpecificationsRUGGEDCOM WIN7000Installation Guide46Mechanical:• Dimensions [H × W × D] 756 mm × 290mm × 195 mm• Weight <15kgPower Interface:• Power supply Input▪ 85-265VAC▪ 37-60VDC(customer supplied for SFD version)• Power Consumption 120W maxStandards ComplianceEMC:• FCC part 15, subpart B, class A• ETSI EN 301 489-1 V1.8.1• ETSI EN 301 489-4 V1.3.1• 1613 section 6.3, 7, 8, 9 Class 1• IEC 61850-3 section 5.7, 5.8• EN55022Safety:• EN60950-22• TUV 60950-1• IEC 60950-1• 1613 Section 5, 6.2• IEC 60255-5 section 6.14Environmental:• Operating Temperature: -40°C to +65°C• Operating Humidity: 5% to 95% non condensing• Weather protected: IP67• IEC 61850-3 section 5.2, 5.3, 5.5• IEC 870-2-2 section 3• Corrosion: MIL-STD-810F 509.4 - salt fogRadio:• FCC: 47CFR Part 15, Part 27, Part 90 Subpart B• IC: SRSP 301.7 Issue 24
RUGGEDCOM WIN7000Installation GuideAppendix CList of Acronyms47List of AcronymsTable: List of AcronymsAcronym DescriptionASN Access Service NetworkBST Base StationIP Internet ProtocolLAN Local Area NetworkLOS Line-of-sightMIMO Multiple-Input, Multiple-OutputNMS Network Management SystemNLOS Non-line-of-sightRF Radio FrequencyWiMAX Worldwide Interoperability for Microwave AccessRUGGEDCOM RUGGEDCOM WiMAX Product FamilyRUGGEDCOMNMS RUGGEDCOM Network Management System
RUGGEDCOM WIN7000Installation GuideAppendix CList of Acronyms48
RUGGEDCOM WIN7000Installation GuideAppendix DWarranty49WarrantySiemens warrants this product for a period of five (5) years from the date of purchase. This product contains nouser-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Forwarranty details, visit www.siemens.com/ruggedcom or contact your customer service representative.Should this product require service, contact the factory at:Siemens Canada Ltd.300 Applewood CrescentConcord, OntarioCanada L4K 5C7Phone: +1 905 856 5288Fax: +1 905 856 1995
RUGGEDCOM WIN7000Installation GuideAppendix DWarranty50

Navigation menu