Siemens 277IWLAN-V200 MOBILE PANEL 277/277F IWLAN User Manual ET 200pro Interface module IM 154 6 PN HF IWLAN

Siemens AG MOBILE PANEL 277/277F IWLAN ET 200pro Interface module IM 154 6 PN HF IWLAN

Contents

User Manual Statements

sCopyright ¤ Siemens AG 2009 SIMATICProduct Information 05/2009 For the operating instructions manual "ET 200pro Interface module IM 154-6 PN HF IWLAN, Edition 02/2009, A5E01648493-02 This product information contains additional reference notes to approvals according to FCC and RSS-210 of Industry Canada and is an extension of chapter 10.1 Standards and approvals. The Product Information is part of the supplied product and the statements made therein are binding in case of doubt. Approval according to FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation. IEEE802.11b or g operation of this product in the USA is firmware-limited to channels 1 through 11.Notice Changes or modifications made to this equipment not expressly approved by SIEMENS may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, wich can be determined by turning the equipment off and on, the user encouraged to try to correct the interference by one or more of the following measures: x Reorient or relocate the receiving antenna. x Increase the separation between the equipment and receiver. x Connect the equipment into an outlet on a circuit different from that to wich the receiver is connected. .
Product Information 2A5E02574910 01Consult the dealer or an experienced radio/TV technician for help. Notice This equipment complies with FCC radiation exposure limits set forth for an uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Professional Installation Notice: To comply with FCC Part 15 rules in the United States, the system must be professionally installed to ensure compliance with the Part 15 certification. It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed in the United States. The use of the system in any other combination (such as co-located antennas transmitting the same information) is expressly forbidden.RSS-210 of Industry Canada "Operation is subjecte to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." "This device has been designed to operate with the antennas listed below, and having a maximum gain of 18 dBi. Antennas not included in this list or having a gain greater than 18 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms." "To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication." That the device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems." "Users should also be cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices." 22Within the 5.15 -5.25 GHz band, this device is only for indoor use operations to reduce anypotential for harmful interference to co-channel MSS operations.

Navigation menu