Sierra Wireless HL7519 Wireless module User Manual

Sierra Wireless Inc. Wireless module

User manual

Download: Sierra Wireless HL7519 Wireless module User Manual
Mirror Download [FCC.gov]Sierra Wireless HL7519 Wireless module User Manual
Document ID2752812
Application IDT7g3lTq4hM48Fl3IEKeShw==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize37.13kB (464127 bits)
Date Submitted2015-09-18 00:00:00
Date Available2016-03-17 00:00:00
Creation Date2017-09-14 04:32:22
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-09-14 04:32:22
Document TitleUser manual
Document CreatorPScript5.dll Version 5.2.2

User Guide
AirPrime HL7519
TBC
1.0
July 28, 2015
User Guide
Important Notice
Due to the nature of wireless communications, transmission and reception of data can never be
guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant
delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used
in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used
in situations where failure to transmit or receive data could result in damage of any kind to the user or
any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless
accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or
received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or
receive such data.
Safety and Hazards
Do not operate the Sierra Wireless modem in areas where cellular modems are not advised without
proper device certifications. These areas include environments where cellular radio can interfere such
as explosive atmospheres, medical equipment, or any other equipment which may be susceptible to
any form of radio interference. The Sierra Wireless modem can transmit signals that could interfere
with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is
on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When
operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard
systems.
Note:
Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door
is open. Sierra Wireless modems may be used at this time.
The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of
a vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In
some states and provinces, operating such communications devices while in control of a vehicle is an
offence.
Limitations of Liability
This manual is provided “as is”. Sierra Wireless makes no warranties of any kind, either expressed or
implied, including any implied warranties of merchantability, fitness for a particular purpose, or
noninfringement. The recipient of the manual shall endorse all risks arising from its use.
The information in this manual is subject to change without notice and does not represent a
commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES
SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL,
GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR
REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS
PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY
THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability
arising under or in connection with the Sierra Wireless product, regardless of the number of events,
occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the
Sierra Wireless product.
Customer understands that Sierra Wireless is not providing cellular or GPS (including A-GPS)
services. These services are provided by a third party and should be purchased directly by the
Customer.
TBC
Rev 1.0
July 28, 2015
User Guide
SPECIFIC DISCLAIMERS OF LIABILITY: CUSTOMER RECOGNIZES AND ACKNOWLEDGES
SIERRA WIRELESS IS NOT RESPONSIBLE FOR AND SHALL NOT BE HELD LIABLE FOR ANY
DEFECT OR DEFICIENCY OF ANY KIND OF CELLULAR OR GPS (INCLUDING A-GPS)
SERVICES.
Patents
This product may contain technology developed by or for Sierra Wireless Inc.
This product includes technology licensed from QUALCOMM®.
This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents
licensed from InterDigital Group and MMP Portfolio Licensing.
Copyright
© 2015 Sierra Wireless. All rights reserved.
Trademarks
Sierra Wireless®, AirPrime®, AirLink®, AirVantage®, WISMO® and the Sierra Wireless and Open AT
logos are registered trademarks of Sierra Wireless, Inc. or one of its subsidiaries.
Watcher® is a registered trademark of NETGEAR, Inc., used under license.
Windows® and Windows Vista® are registered trademarks of Microsoft Corporation.
Macintosh® and Mac OS X® are registered trademarks of Apple Inc., registered in the U.S. and other
countries.
QUALCOMM® is a registered trademark of QUALCOMM Incorporated. Used under license.
Other trademarks are the property of their respective owners.
Contact Information
Sales Desk:
Post:
Technical Support:
RMA Support:
Fax:
Web:
Phone:
1-604-232-1488
Hours:
8:00 AM to 5:00 PM Pacific Time
Contact:
http://www.sierrawireless.com/sales
Sierra Wireless
13811 Wireless Way
Richmond, BC
Canada
V6V 3A4
support@sierrawireless.com
repairs@sierrawireless.com
1-604-231-1109
http://www.sierrawireless.com/
Consult our website for up-to-date product descriptions, documentation, application notes, firmware
upgrades, troubleshooting tips, and press releases: www.sierrawireless.com
TBC
Rev 1.0
July 28, 2015
User Guide
Document History
Version
Date
Updates
1.0
July 28, 2015
Creation
TBC
Rev 1.0
July 28, 2015
Contents
1. INTRODUCTION .................................................................................................... 8
1.1.
Common Flexible Form Factor (CF3)............................................................................... 8
1.2.
Physical Dimensions ....................................................................................................... 8
1.3.
General Features ............................................................................................................ 9
1.4.
Architecture ................................................................................................................... 11
1.5.
Interfaces ...................................................................................................................... 11
1.6.
Connection Interface ..................................................................................................... 12
1.7.
ESD .............................................................................................................................. 12
1.8.
Environmental & Certifications ...................................................................................... 13
1.8.1.
Environmental Specifications ................................................................................. 13
1.8.2.
Regulatory ............................................................................................................. 13
1.8.3.
RoHS Directive Compliant ..................................................................................... 13
1.8.4.
Disposing of the Product ........................................................................................ 14
1.8.5.
References ............................................................................................................ 14
2. DETAILED INTERFACE SPECIFICATIONS ....................................................... 15
2.1.
Power Supply ................................................................................................................ 15
2.2.
VGPIO........................................................................................................................... 15
3. MECHANICAL DRAWINGS................................................................................. 16
4. FCC REGULATIONS ........................................................................................... 18
5. TERMS AND ABBREVIATIONS.......................................................................... 20
TBC
Rev 1.0
July 28, 2015
List of Figures
Figure 1.
AirPrime HL7519 Architecture Overview ....................................................................... 11
Figure 2.
AirPrime HL7519 Mechanical Overview ........................................................................ 12
Figure 3.
AirPrime HL7519 Mechanical Drawing .......................................................................... 16
Figure 4.
AirPrime HL7519 Dimensions Drawing ......................................................................... 17
TBC
Rev 1.0
July 28, 2015
List of Tables
Table 1.
Supported Bands/Connectivity ........................................................................................ 8
Table 2.
AirPrime HL7519 Features .............................................................................................. 9
Table 3.
ESD Specifications........................................................................................................ 12
Table 4.
AirPrime HL7519 Environmental Specifications ............................................................ 13
Table 5.
Regulation Compliance ................................................................................................. 13
Table 6.
Power Supply ................................................................................................................ 15
Table 7.
VGPIO Electrical Characteristics ................................................................................... 15
TBC
Rev 1.0
July 28, 2015
1.
Introduction
This document is the Product Technical Specification for the AirPrime HL7519 Embedded Module. It
defines the high level product features and illustrates the interfaces for these features. This document
is intended to cover the hardware aspects of the product, including electrical and mechanical.
The AirPrime HL7519 belongs to the AirPrime HL Series from Essential Connectivity Module family.
These are industrial grade Embedded Wireless Modules that provide data connectivity on wireless
networks (as listed in Table 1 Supported Bands/Connectivity).
The HL7519 supports a large variety of interfaces such as USB 2.0, UART, GPIOs, and dual SIM to
provide customers with the highest level of flexibility in implementing high-end solutions.
Table 1.
1.1.
Supported Bands/Connectivity
RF Band
Transmit band (Tx)
Receive band (Rx)
LTE B2
1850 to 1910 MHz
1930 to 1990 MHz
LTE B4
1710 to 1755 MHz
2110 to 2155 MHz
LTE B13
777 to 787 MHz
746 to 756 MHz
Common Flexible Form Factor (CF3)
The AirPrime HL7519 belongs to the Common Flexible Form Factor (CF3) family of modules. This
family consists of a series of WWAN modules that share the same mechanical dimensions (same
width and length with varying thicknesses) and footprint. The CF3 form factor provides a unique
solution to a series of problems faced commonly in the WWAN module space as it:

Accommodates multiple radio technologies (from 2G to LTE advanced) and band groupings

Supports bit-pipe (Essential Module Series) and value add (Smart Module Series) solutions

Offers electrical and functional compatibility

Provides Direct Mount as well as Socketability depending on customer needs
1.2.
Physical Dimensions
AirPrime HL7519 module is a compact, robust, fully shielded module with the following dimensions:

Length: 23 mm

Width: 22 mm

Thickness: 2.5 mm

Weight: 3.5 g
Note:
TBC
Dimensions specified above are typical values.
Rev 1.0
July 28, 2015
User Guide
Introduction
1.3.
General Features
The table below summarizes the AirPrime HL7519 features.
Table 2.
AirPrime HL7519 Features
Feature
Physical
Electrical
RF
SIM interface
Application interface
Protocol Stack
TBC
Description

Small form factor (146-pin solderable LGA pad) – 23mm x 22mm x 2.5mm
(nominal)

Complete body shielding

RF connection pads (RF main interface)

Baseband signals connection
Single or double supply voltage (VBATT and VBATT_PA) – 3.2V – 4.5V
Tri=band LTE:

LTE B2: 1900 PCS

LTE B4: 1700 AWS

LTE B13: 700

1.8V/3V support

SIM extraction / hot plug detection

SIM/USIM support

Conforms with ETSI UICC Specifications

Supports SIM application tool kit with proactive SIM commands

NDIS NIC interface support (Windows XP, Windows 7, Windows 8,
Windows CE, Linux)

Multiple non-multiplexed USB channel support

Dial-up networking

USB selective suspend to maximize power savings

CMUX multiplexing over UART (not available on the HL7519)

AT command interface – 3GPP 27.007 standard, plus proprietary extended
AT commands

Single mode LTE operation:

LTE FDD, bandwidth 1.4-20 MHz

System Release: 3GPP Rel. 9

Category 4 (up to 150 Mbit/s in downlink, 50 Mbit/s in uplink)

MIMO 2x2

Max modulation 64 QAM DL, 16 QAM UL

Intra-frequency and inter-frequency mobility

SMS over SGs and IMS

SON ANR

Public Warning System PWS
Rev 1.0
July 28, 2015
User Guide
Feature
SMS
Introduction
Description

SMS over SGs and IMS

SMS MO and MT

SMS saving to SIM card or ME storage

SMS reading from SIM card or ME storage

SMS sorting

SMS concatenation

SMS Status Report

SMS replacement support

SMS storing rules (support of AT+CNMI, AT+CNMA)

Multiple (up to 20) cellular packet data profiles

Sleep mode for minimum idle power draw

Mobile-originated PDP context activation / deactivation

Support QoS profile

Release 97 – Precedence Class, Reliability Class, Delay Class, Peak
Throughput, Mean Throughput

Release 99 QoS negotiation – Background, Interactive, and Streaming

Static and Dynamic IP address. The network may assign a fixed IP address
or dynamically assign one using DHCP (Dynamic Host Configuration
Protocol).
Connectivity

Supports PAP and CHAP authentication protocols

PDP context type (IPv4, IPv6, IPv4v6). IP Packet Data Protocol context

RFC1144 TCP/IP header compression
Operating temperature ranges (industrial grade):
Environmental
RTC
TBC


Class A: -30°C to +70°C
Class B: -40°C to +85°C
Real Time Clock (RTC) with calendar
Rev 1.0
July 28, 2015
10
User Guide
1.4.
Introduction
Architecture
The figure below presents an overview of the AirPrime HL7519’s internal architecture and external
interfaces.
Figure 1.
1.5.
AirPrime HL7519 Architecture Overview
Interfaces
The AirPrime HL7519 module provides the following interfaces and peripheral connectivity:
TBC

1x - 4-pin UART

1x - Active Low RESET

1x - USB 2.0

1x - Backup Battery Interface

2x - System Clock Out

1x - Active Low POWER-ON

1x - 1.8V/3V SIM

1x - JTAG Interface

14x - GPIOs (5 of which have multiplexes)

1x - Main Antenna

1x - RX Diversity Antenna

1x – VGPIO

1x – TX ON

1x - ADC

1x – Debug Interface
Rev 1.0
July 28, 2015
11
User Guide
Introduction
1.6.
Connection Interface
The AirPrime HL7519 module is an LGA form factor device. All electrical and mechanical connections
are made through the 146 Land Grid Array (LGA) pads on the bottom side of the PCB.
Figure 2.
AirPrime HL7519 Mechanical Overview
The 146 pads have the following distribution:

66 inner signal pads, 1x0.5mm, pitch 0.8mm

1 reserved test point (do not connect), 1.0mm diameter

7 test point (JTAG), 0.8mm diameter, 1.20mm pitch

64 inner ground pads, 1.0x1.0mm, pitch 1.825mm/1.475mm

4 inner corner ground pads, 1x1mm

4 outer corner ground pads, 1x0.9mm
1.7.
ESD
Refer to the following table for ESD Specifications.
Note:
Table 3.
Information specified in the following table is preliminary and subject to change.
ESD Specifications
Category
Connection
Operational
RF ports
Specification
IEC-61000-4-2 — Level (Electrostatic Discharge Immunity Test)
Unless otherwise specified:
Non-operational
Signals
TBC



Host connector
interface
SIM connector
Other host signals
Rev 1.0
JESD22-A114 +/- 2kV Human Body Model
JESD22-A115 +/- 200V Machine Model
JESD22-C101C +/- 250V Charged Device Model
Adding ESD protection is highly recommended at the point where
the USIM contacts are exposed, and for any other signals that
would be subjected to ESD by the user.
July 28, 2015
12
User Guide
Introduction
1.8.
Environmental & Certifications
1.8.1.
Environmental Specifications
The environmental specification for both operating and storage conditions are defined in the table
below.
Table 4.
AirPrime HL7519 Environmental Specifications
Conditions
Range
Operating Class A
-30°C to +70°C
Operating Class B
-40°C to +85°C
Storage
-40°C to +85°C
Class A is defined as the operating temperature ranges that the device:

Shall exhibit normal function during and after environmental exposure.

Shall meet the minimum requirements of 3GPP or appropriate wireless standards.
Class B is defined as the operating temperature ranges that the device:

Shall remain fully functional during and after environmental exposure

Shall exhibit the ability to establish an SMS or DATA call (emergency call) at all times even
when one or more environmental constraint exceeds the specified tolerance.

Unless otherwise stated, full performance should return to normal after the excessive
constraint(s) have been removed.
1.8.2.
Regulatory
The AirPrime HL7519 is compliant with FCC and IC regulations.
FCC and IC compliance will be reflected on the AirPrime HL7519 label.
Table 5.
Regulation Compliance
Document
Current Version
Description
FCC Part 22, 24, 27
NA
Federal Communications Commission
1.8.3.
RoHS Directive Compliant
The AirPrime HL7519 modules are compliant with RoHS Directive 2011/65/EU which sets limits for
the use of certain restricted hazardous substances. This directive states that “from 1st July 2006, new
electrical and electronic equipment put on the market does not contain lead, mercury, cadmium,
hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE)”.
TBC
Rev 1.0
July 28, 2015
13
User Guide
1.8.4.
Introduction
Disposing of the Product
This electronic product is subject to the EU Directive 2012/19/EU for Waste Electrical
and Electronic Equipment (WEEE). As such, this product must not be disposed of at a
municipal waste collection point. Please refer to local regulations for directions on
how to dispose of this product in an environmental friendly manner.
1.8.5.
[1]
References
AirPrime HL Series Customer Process Guidelines
Reference Number: 4114330
[2]
AirPrime HL7519, HL7548 and HL7519 AT Commands Interface Guide
Reference Number: TBC
TBC
Rev 1.0
July 28, 2015
14
2.
Detailed Interface Specifications
Note:
If not specified, all electrical values are given for VBATT=3.7V and an operating temperature of
25°C.
For standard applications, VBATT and VBATT_PA must be tied externally to the same power
supply. For some specific applications, AirPrime HL7519 modules support separate VBATT and
VBATT_PA connection if requirements below are fulfilled.
2.1.
Power Supply
The AirPrime HL7519 module is supplied through the VBATT signal with the following characteristics.
Table 6.
Power Supply
Supply
Minimum
Typical
Maximum
VBATT voltage (V)
3.21
3.7
4.5
VBATT_PA voltage (V) Full Specification
3.21
3.7
4.5
VBATT_PA voltage (V) Extended Range
2.8
3.7
4.5
This value has to be guaranteed during the burst.
Note:
Load capacitance for VBATT is around 32µF ± 20% embedded inside the module.
Load capacitance for VBATT_PA is around 10µF ± 20% embedded inside the module.
2.2.
VGPIO
The VGPIO output can be used to:

Pull-up signals such as I/Os

Supply the digital transistors driving LEDs
The VGPIO output is available when the AirPrime HL7519 module is switched ON.
Table 7.
VGPIO Electrical Characteristics
Parameter
Min
Typ
Max
Remarks
Voltage level (V)
1.7
1.8
1.9
Both active mode and sleep mode
Current capability
Active Mode (mA)
50
Power management support up to 50mA output
in Active mode
Current capability
Sleep Mode (mA)
Power management support up to 3mA output in
Sleep mode
Rise Time(ms)
1.5
Start-Up time from 0V
TBC
Rev 1.0
July 28, 2015
15
3.
Figure 3.
TBC
Mechanical Drawings
AirPrime HL7519 Mechanical Drawing
Rev 1.0
July 28, 2015
16
User Guide
Figure 4.
TBC
Mechanical Drawings
AirPrime HL7519 Dimensions Drawing
Rev 1.0
July 28, 2015
17
4.
FCC Regulations
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE – FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
The HL7519 module has been granted modular approval for mobile applications. Integrators may use
the HL7519 module in their final products without additional FCC certification if they meet the
following conditions. Otherwise, additional FCC approvals must be obtained.
1. At least 20 cm separation distance between the antenna and the user’s body must be
maintained at all times.
2. To comply with FCC regulations limiting both maximum RF output power and human
exposure to RF radiation, the maximum antenna gain including cable loss in a mobileonly exposure condition must not exceed:

9.01 dBi in Band 2

6.00 dBi in Band 4

10.91 dBi in Band 13
3. This device and its antenna(s) must not transmit be co-located or operating in conjunction
with any other antenna or transmitter, except in accordance with FCC multi-transmitter RF
exposure product procedures.
4. The RF signal must be routed on the application board using tracks with a 50Ω
characteristic impedance. Basically, the characteristic impedance depends on the
dielectric, the track width and the ground plane spacing. In order to respect this constraint,
Sierra Wireless recommends using MicroStrip or StripLine structure and computing the
Tracks width with a simulation tool (like AppCad shown in the figure below and that is
available free of charge at http://www.agilent.com).
TBC
Rev 1.0
July 28, 2015
18
User Guide
FCC Regulations
If a multi-layered PCB is used, the RF path on the board must not cross any signal (digital,
analog or supply).
If necessary, use StripLine structure and route the digital line(s) "outside" the RF structure. An
example of proper routing is shown in the figure below.
Stripline and Coplanar design requires having a correct ground plane at both sides.
Consequently, it is necessary to add some vias along the RF path. It is recommended to use
Stripline design if the RF path is fairly long (more than 3cm), since MicroStrip design is not
shielded. Consequently, the RF signal (when transmitting) may interfere with neighbouring
electronics (AF amplifier, etc.). In the same way, the neighbouring electronics (microcontrollers, etc.) may degrade the reception performances. The antenna connector is
intended to be directly connected to a 50Ω antenna and no matching is needed.
5. A label must be affixed to the outside of the end product into which the HL7519 module is
incorporated, with a statement similar to the following:
This device contains FCC ID: N7NHL7519
6. A user manual with the end product must clearly indicate the operating requirements and
conditions that must be observed to ensure compliance with current FCC RF exposure
guidelines.
The end product with an embedded HL7519 module may also need to pass the FCC Part 15
unintentional emission testing requirements and be properly authorized per FCC Part 15.
Note:
TBC
If this module is intended for use in a portable device, you are responsible for separate approval to
satisfy the SAR requirements of FCC Part 2.1093.
Rev 1.0
July 28, 2015
19
5.
Terms and Abbreviations
Abbreviation
Definition
ADC
Analog to Digital Converter
AGC
Automatic Gain Control
AT
Attention (prefix for modem commands)
CDMA
Code Division Multiple Access
CF3
Common Flexible Form Factor
CLK
ClocK
CODEC
Coder DECoder
CPU
Central Processing Unit
DAC
Digital to Analog Converter
DTR
Data Terminal Ready
EGNOS
European Geostationary Navigation Overlay Service
EMC
ElectroMagnetic Compatibility
EMI
ElectroMagnetic Interference
EN
Enable
ESD
ElectroStatic Discharges
ETSI
European Telecommunications Standards Institute
FDMA
Frequency-division multiple access
GAGAN
GPS aided geo augmented navigation
GLONASS
GLObal NAvigation Satellite System
GND
GrouND
GNSS
Global Navigation Satellite System
GPIO
General Purpose Input Output
GPRS
General Packet Radio Service
GSM
Global System for Mobile communications
Hi Z
High impedance (Z)
IC
Integrated Circuit
IMEI
International Mobile Equipment Identification
I/O
Input / Output
LED
Light Emitting Diode
LNA
Low Noise Amplifier
MAX
MAXimum
MIN
MINimum
MSAS
Multi-functional Satellite Augmentation System
N/A
Not Applicable
PA
Power Amplifier
PC
Personal Computer
PCB
Printed Circuit Board
PCL
Power Control Level
PLL
Phase Lock Loop
PWM
Pulse Width Modulation
TBC
Rev 1.0
July 28, 2015
20
User Guide
Abbreviation
Terms and Abbreviations
Definition
QZSS
Quasi-Zenith Satellite System
RF
Radio Frequency
RFI
Radio Frequency Interference
RMS
Root Mean Square
RST
ReSeT
RTC
Real Time Clock
RX
Receive
SCL
Serial CLock
SDA
Serial DAta
SIM
Subscriber Identification Module
SMD
Surface Mounted Device/Design
SPI
Serial Peripheral Interface
SW
SoftWare
PSRAM
Pseudo Static RAM
TBC
To Be Confirmed
TBD
To Be Defined
TP
Test Point
TX
Transmit
TYP
TYPical
UART
Universal Asynchronous Receiver-Transmitter
UICC
Universal Integrated Circuit Card
USB
Universal Serial Bus
UIM
User Identity Module
VBATT
Main Supply Voltage from Battery or DC adapter
VSWR
Voltage Standing Wave Ratio
WAAS
Wide Area Augmentation System
TBC
Rev 1.0
July 28, 2015
21

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : 
Create Date                     : 2015:09:15 14:00:28+08:00
Modify Date                     : 2015:09:16 15:54:56+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2015:09:16 15:54:56+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Creator                         : 
Title                           : 
Document ID                     : uuid:751687c9-3db7-4ff4-a4e0-6307bc8aff6f
Instance ID                     : uuid:5256511d-00fd-4683-8bbd-404126d507f8
Page Count                      : 21
EXIF Metadata provided by EXIF.tools
FCC ID Filing: N7NHL7519

Navigation menu