Sierra Wireless MC8805 Radio Module User Manual TempConfidential 411xxxx AirPrime MC8805 Hardware Integration Guide v1 Draft B

Sierra Wireless Inc. Radio Module TempConfidential 411xxxx AirPrime MC8805 Hardware Integration Guide v1 Draft B

UserManual.wiki >

Sierra Wireless >

MC8805 User Manual

TempConfidential_411xxxx AirPrime MC8805 Hardware Integration Guide v1 - Draft B

AirPrime MC8805Hardware Integration Guide411xxxxRev 1Distribution under NDA only Contents subject to change

PrefaceRev 1 Dec.12 Proprietary and Confidential - Contents subject to change 3Important NoticeDue to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data.Safety and HazardsDo not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem MUST BE POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with this equipment.Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems.Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time.The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence.Limitation of LiabilityThe information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product.

Rev 1 Dec.12 Proprietary and Confidential - Contents subject to change 5ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Required connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Module power states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9RF Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11RF connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Antenna and cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Ground connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Interference and sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Interference from other wireless devices . . . . . . . . . . . . . . . . . . . . . . . . .14Host-generated RF interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Device-generated RF interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Methods to mitigate decreased Rx performance . . . . . . . . . . . . . . . . . . .14Radiated Spurious Emissions (RSE) . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Radiated sensitivity measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Regulatory Compliance and Industry Certifications . . . . . . . . . . . . . . . . . . .17Important notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Safety and hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Important compliance information for North American users . . . . . . . . . . . . 18Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Hardware Integration Guide6 Proprietary and Confidential - Contents subject to change 411xxxx

Rev 1 Dec.12 Proprietary and Confidential - Contents subject to change 711: IntroductionThe Sierra Wireless MC8805 PCI Express Mini Card is a compact, lightweight, wireless UMTS-based modem.The MC8805 provides DC-HSPA+, HSPA+, HSDPA, HSUPA, WCDMA, GSM, GPRS, EDGE, and GNSS connectivity for notebook, ultrabook, and tablet computers over several radio frequency bands. The device also supports 2G / 3G roaming, subject to carrier provisioning.AccessoriesThe Universal Development Kit (UDK) is a hardware development platform for AirPrime MC-series modules. It contains hardware components for evaluating and developing with the module, including:•Development board•Cables•Antennas (Additional antennas may be required to support all bands.)•Initial allotment of support hours•Other accessoriesFor instructions on setting up the UDK (part number 6000270), see [4] PCI Express Mini Card Dev Kit Quick Start Guide (Doc# 2130705).Required connectorsTabl e 1-1 describes the connectors used to integrate the MC8805 into your host device.Table 1-1: Required host-module connectors1Connector type DescriptionRF cables •Mate with Hirose U.FL connectors (model U.FL #CL331-0471-0-10)•Two connector jacksEDGE (52-pin) •Industry-standard mating connector•Some manufacturers include Tyco, Foxconn, Molex•Example: UDK board uses Molex 67910-0001SIM •Industry-standard connector. Type depends on how host device exposes the SIM socket•Example: UDK board uses ITT CCM03-3518

Hardware Integration Guide8 Proprietary and Confidential - Contents subject to change 411xxxx1. Manufacturers / part numbers are for reference only and are subject to change. Choose connectors that are appropriate for your own design.

Rev 1 Dec.12 Proprietary and Confidential - Contents subject to change 922: PowerPower supplyThe host provides power to the MC8805 through multiple power and ground pins.The host must provide safe and continuous power at all times; the module does not have an independent power supply, or protection circuits to guard against electrical issues.For detailed pinout and voltage / current requirements of this module, see the AirPrime MC8805 Product Technical Specification Document & Customer Design Guidelines.Module power statesThe module has four power states, as described in Ta b l e 2-1. Table 2-1: Module power states State DetailsHost is poweredModule is poweredUSB interface activeRF enabledNormal(Default state)•Module is active•Default state when VCC is first applied in the absence of W_DISABLE_N control•Module is capable of placing / receiving calls, or establishing data connections on the wireless network•Current consumption is affected by several factors, including:•Radio band being used•Transmit power•Receive gain settings•Data rate•Number of active Tx time slots   Low power(‘Airplane mode’)•Module is active•Module enters this state:•Under host interface control:·Host issues AT+CFUN=0 ([1] AT Command Set for User Equipment (UE) (Release 6) (Doc# 3GPP TS 27.007))), or·Host asserts W_DISABLE_N, after AT!PCOFFEN=0 has been issued.•Automatically, when critical temperature or voltage trigger limits have been reached   

Hardware Integration Guide10 Proprietary and Confidential - Contents subject to change 411xxxxSleep •Normal state of module between calls or data connections•Module cycles between wake (polling the network) and sleep, at network provider-determined interval.   Disconnected •Host power source is disconnected from the module and all voltages associated with the module are at 0 V.   Table 2-1: Module power states (Continued)State DetailsHost is poweredModule is poweredUSB interface activeRF enabled

Rev 1 Dec.12 Proprietary and Confidential - Contents subject to change 1133: RF SpecificationsThe MC8805 operates on the frequency bands listed below. Table 3-1: WCDMA frequency band support11. WCDMA channel spacing is 5 MHz, but this can be adjusted to optimize performance in a particular deployment scenario.Band FrequenciesBand 1WCDMA 2100 Tx: 1920–1980 MHzRx: 2110–2170 MHzBand 2WCDMA 1900 Tx: 1850–1910 MHzRx: 1930–1990 MHzBand 5WCDMA 850 Tx: 824–849 MHzRx: 869–894 MHzBand 8WCDMA 900 Tx: 880–915 MHzRx: 925–960 MHzTable 3-2: GSM frequency band support Band FrequenciesGSM 850 Tx: 824–849 MHzRx: 869–894 MHzEGSM 900 Tx: 880–915 MHzRx: 925–960 MHzGSM 1800 Tx: 1710–1785 MHzRx: 1805–1880 MHzGSM 1900 Tx: 1850–1910 MHzRx: 1930–1990 MHzTable 3-3: GNSS frequency band support Band FrequenciesGPS Rx: 1575.42 MHzGLONASS Rx: 1602 MHz

RF SpecificationsRev 1 Dec.12 Proprietary and Confidential - Contents subject to change 13high levels of broadband or spurious noise can degrade the module’s perfor-mance.•Connecting cables between the module and the antenna must have 50  impedance. If the impedance of the module is mismatched, RF performance is reduced significantly.•Antenna cables should be routed, if possible, away from noise sources (switching power supplies, LCD assemblies, etc.). If the cables are near the noise sources, the noise may be coupled into the RF cable and into the antenna.Disabling the diversity antenna•Use the AT command !RXDEN=0 to disable receive diversity or !RXDEN=1 to enable receive diversity.Note: A diversity antenna is used to improve connection quality and reliability through redundancy. Because two antennas may experience difference interference effects (signal distortion, delay, etc.), when one antenna receives a degraded signal, the other may not be similarly affected.Ground connectionWhen connecting the module to system ground:•Prevent noise leakage by establishing a very good ground connection to the module through the host connector.•Connect to system ground using the two mounting holes at the top of the module.•Minimize ground noise leakage into the RF.Depending on the host board design, noise could potentially be coupled to the module from the host board. This is mainly an issue for host designs that have signals traveling along the length of the module, or circuitry operating at both ends of the module interconnects.Interference and sensitivitySeveral interference sources can affect the module’s RF performance (RF desense). Common sources include power supply noise and device-generated RF.RF desense can be addressed through a combination of mitigation techniques (Methods to mitigate decreased Rx performance on page 14) and radiated sensitivity measurement (Radiated sensitivity measurement on page 15).Note: The MC8805 is based on ZIF (Zero Intermediate Frequency) technologies. When performing EMC (Electromagnetic Compatibility) tests, there are no IF (Intermediate Frequency) components from the module to consider.

Hardware Integration Guide14 Proprietary and Confidential - Contents subject to change 411xxxxInterference from other wireless devicesWireless devices operating inside the host device can cause interference that affects the module.To determine the most suitable locations for antennas on your host device, evaluate each wireless device’s radio system, considering the following:•Any harmonics, sub-harmonics, or cross-products of signals generated by wireless devices that fall in the module’s Rx range may cause spurious response, resulting in decreased Rx performance.•The Tx power and corresponding broadband noise of other wireless devices may overload or increase the noise floor of the module’s receiver, resulting in Rx desense.The severity of this interference depends on the closeness of the other antennas to the module’s antenna. To determine suitable locations for each wireless device’s antenna, thoroughly evaluate your host device’s design.Host-generated RF interferenceAll electronic computing devices generate RF interference that can negatively affect the receive sensitivity of the module.Proximity of host electronics to the antenna in wireless devices can contribute to decreased Rx performance. Components that are most likely to cause this include:•Microprocessor and memory•Display panel and display drivers•Switching-mode power suppliesDevice-generated RF interferenceThe module can cause interference with other devices. Wireless devices such as AirPrime embedded modules transmit in bursts (pulse transients) for set durations (RF burst frequencies). Hearing aids and speakers convert these burst frequencies into audible frequencies, resulting in audible noise. Methods to mitigate decreased Rx performanceIt is important to investigate sources of localized interference early in the design cycle. To reduce the effect of device-generated RF on Rx performance:•Put the antenna as far as possible from sources of interference. The drawback is that the module may be less convenient to use.•Shield the host device. The module itself is well shielded to avoid external interference. However, the antenna cannot be shielded for obvious reasons. In most instances, it is necessary to employ shielding on the components of the host device (such as the main processor and parallel bus) that have the highest RF emissions. •Filter out unwanted high-order harmonic energy by using discrete filtering on low frequency lines.

RF SpecificationsRev 1 Dec.12 Proprietary and Confidential - Contents subject to change 15•Form shielding layers around high-speed clock traces by using multi-layer PCBs.•Route antenna cables away from noise sources.Radiated Spurious Emissions (RSE)When designing an antenna for use with AirPrime embedded modules, the host device with an AirPrime embedded module must satisfy the radiated spurious emission (RSE) test cases described in:•CE/ETSI EN 301 908 (WCDMA), test numbers 5.3.1 (‘Radiated Emissions (UE)’)•CE/ETSI EN 301 511 (GSM), test 5.2.16 (‘Radiated Spurious Emissions - MS allocated a channel’). This test uses the procedure and requirement outlined in 3GPP 51.010 (GSM) section 12.2.1 of the same test name.Note that antenna impedance affects radiated emissions, which must be compared against the conducted 50-ohm emissions baseline. (AirPrime embedded modules meet the 50-ohm conducted emissions requirement.)Note: GSM spurious emissions are most likely to have RSE issues, but in general, RSE requirements must be met on all models with user-designed antennas.Radiated sensitivity measurementA wireless host device contains many noise sources that contribute to a reduction in Rx performance.To determine the extent of any receiver performance desensitization due to self-generated noise in the host device, over-the-air (OTA) or radiated testing is required. This testing can be performed by Sierra Wireless or you can use your own OTA test chamber for in-house testing.

Hardware Integration Guide16 Proprietary and Confidential - Contents subject to change 411xxxx

Rev 1 Dec.12 Proprietary and Confidential - Contents subject to change 1744: Regulatory Compliance and Industry CertificationsThis module is designed to meet, and upon commercial release, will meet the requirements of the following regulatory bodies and regulations, where applicable:•Federal Communications Commission (FCC) of the United States•The National Communications Commission (NCC) of Taiwan, Republic of China•Radio Equipment and Telecommunications Terminal Equipment (R&TTE) Directive of the European UnionUpon commercial release, the following industry approvals will have been obtained, where applicable:•GCF-CC•Full GCFAdditional certifications may be obtained upon customer request — contact your Sierra Wireless account representative for details.Additional testing and certification may be required for the end product with an embedded MC8805 modem and are the responsibility of the OEM. Sierra Wireless offers professional services-based assistance to OEMs with the testing and certification process, if required.Important noticeBecause of the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless and its affiliates accept no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data.Safety and hazardsDo not operate your MC8805 modem:•In areas where blasting is in progress

Hardware Integration Guide18 Proprietary and Confidential - Contents subject to change 411xxxx•Where explosive atmospheres may be present including refuelling points, fuel depots, and chemical plants•Near medical equipment, life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the MC8805 modem MUST BE POWERED OFF. Otherwise, the MC8805 modem can transmit signals that could interfere with this equipment.In an aircraft, the MC8805 modem MUST BE POWERED OFF. Otherwise, the MC8805 modem can transmit signals that could interfere with various onboard systems and may be dangerous to the operation of the aircraft or disrupt the cellular network. Use of a cellular phone in an aircraft is illegal in some jurisdictions. Failure to observe this instruction may lead to suspension or denial of cellular telephone services to the offender, or legal action or both.Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. The MC8805 modem may be used normally at this time.Important compliance information for North American usersNote: Details are preliminary and subject to change.The MC8805 modem has been granted modular approval for mobile applications. Integrators may use the MC8805 modem in their final products without additional FCC certification if they meet the following conditions. Otherwise, additional FCC approvals must be obtained.1. At least 20 cm separation distance between the antenna and the user’s body must be maintained at all times.2. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed:Note: Gain values are preliminary and subject to change.·6.5 dBi in Cellular band·3 dBi in PCS band3. The MC8805 modem may transmit simultaneously with other collocated radio transmitters within a host device, provided the following conditions are met:·Each collocated radio transmitter has been certfied by FCC for mobile application.·At least 20 cm separation distance between the antennas of the collocated transmitters and the user’s body must be maintained at all times.

Regulatory Compliance and Industry CertificationsRev 1 Dec.12 Proprietary and Confidential - Contents subject to change 19·The output power and antenna gain must not exceed the limits and configu-rations stipulated in the following table.4. A label must be affixed to the outside of the end product into which the MC8805 modem is incorporated, with a statement similar to the following:· This device contains FCC ID: N7NMC88055. A user manual with the end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines.The end product with an embedded MC8805 modem may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15.Note: If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093.Device Technology Band Frequency(MHz) Maximum conducted power(dBm)Maximum antenna gain(dBi)MC8805 Mini Card UMTS 21850–1910 23.5 35824–849 23.5 3GSM Cellular (850) 824–849 33 3PCS (1900) 1850–1910 30 3Collocated transmitters1WLAN 2400–2500 29 5.05150–5850 29 5.0WiMAX 2300–2400 29 5.02500–2700 29 5.03300–3800 29 5.0BT 2400–2500 15 5.01. Valid collocated transmitter combinations: WLAN+BT; WiMAX+BT.(WLAN+WiMAX+BT is not permitted.)

Hardware Integration Guide20 Proprietary and Confidential - Contents subject to change 411xxxx

Rev 1 Dec.12 Proprietary and Confidential - Contents subject to change 2155: AcronymsTable 5-1: Acronyms and definitions Acronym or term Definition3GPP 3rd Generation Partnership Project8PSK Octagonal Phase Shift KeyingAGC Automatic Gain ControlA-GPS Assisted GPSAPI Application Programming InterfaceBER Bit Error Rate — A measure of receive sensitivityBLER Block Error Ratebluetooth Wireless protocol for data exchange over short distancesCDG CDMA Development Group—a consortium of companies that develop and promote the products and services for CDMA wireless systems.CDMA Code Division Multiple Access.A wideband spread spectrum technique used in digital cellular, personal communications services, and other wireless networks. Wide channels (1.25 MHz) are obtained through spread spectrum transmissions, thus allowing many active users to share the same channel. Each user is assigned a unique digital code, which differentiates the individual conversations on the same channel.CQI Channel Quality IndicationCOM Communication portCS Circuit-switchedCW Continuous waveformdB Decibel = 10 x log10 (P1 / P2)P1 is calculated power; P2 is reference powerDecibel = 20 x log10 (V1 / V2)V1 is calculated voltage, V2 is reference voltagedBm A logarithmic (base 10) measure of relative power (dB for decibels); relative to milliwatts (m). A dBm value will be 30 units (1000 times) larger (less negative) than a dBW value, because of the difference in scale (milliwatts vs. watts).DC-HSPA+ Dual Carrier HSPA+DCS Digital Cellular SystemA cellular communication infrastructure that uses the 1.8 GHz radio spectrum.DL Downlink (network to mobile)DUN Dial-Up NetworkingDRX Discontinuous Reception

Hardware Integration Guide22 Proprietary and Confidential - Contents subject to change 411xxxxDSM Distributed Shared MemoryDUT Device Under TestEDGE Enhanced Data rates for GSM EvolutionEIRP Effective (or Equivalent) Isotropic Radiated PowerEMC Electromagnetic CompatibilityEMI Electromagnetic InterferenceERP Effective Radiated PowerESD Electrostatic DischargeFCC Federal Communications CommissionThe U.S. federal agency that is responsible for interstate and foreign communications. The FCC regulates commercial and private radio spectrum management, sets rates for communications services, determines standards for equipment, and controls broadcast licensing. Consult www.fcc.gov.FDMA Frequency Division Multiple AccessFER Frame Error Rate — A measure of receive sensitivity.firmware Software stored in ROM or EEPROM; essential programs that remain even when the system is turned off. Firmware is easier to change than hardware but more permanent than software stored on disk.FOTA Firmware Over The Air — Technology used to download firmware upgrades directly from the service provider, over the air.FOV Field Of ViewFSN Factory Serial Number—A unique serial number assigned to the mini card during manufacturing.GCF Global Certification ForumGLONASS Global Navigation Satellite System — A Russian system that uses a series of 24 satellites in middle circular orbit to provide navigational data.GMSK Gaussian Minimum Shift Keying modulationGNSS Global Navigation Satellite Systems (GPS plus GLONASS)GPRS General Packet Radio ServiceGPS Global Positioning SystemAn American system that uses a series of 24 satellites in middle circular orbit to provide navigational data.GSM Global System for Mobile CommunicationsHost The device into which an embedded module is integratedHSDPA High Speed Downlink Packet AccessTable 5-1: Acronyms and definitions (Continued)Acronym or term Definition

AcronymsRev 1 Dec.12 Proprietary and Confidential - Contents subject to change 23HSPA+ Enhanced HSPA, as defined in 3GPP Release 7 and beyondHSUPA High Speed Uplink Packet AccessHz Hertz = 1 cycle / secondIC Industry CanadaIF Intermediate FrequencyIMEI International Mobile Equipment Identityinrush current Peak current drawn when a device is connected or powered oninter-RAT Radio Access TechnologyIOT Interoperability TestingIS Interim Standard.After receiving industry consensus, the TIA forwards the standard to ANSI for approval.LED Light Emitting Diode.A semiconductor diode that emits visible or infrared light.LHCP Left-Hand Circular PolarizedLNA Low Noise AmplifierLPM Low Power ModeLPT Line Print TerminalLTE Long Term Evolution—a high-performance air interface for cellular mobile communication systems.MCS Modulation and Coding SchemeMHz Megahertz = 10e6 HzMIMO Multiple Input Multiple Output—wireless antenna technology that uses multiple antennas at both transmitter and receiver side. This improves performance.NAS / AS Network Access ServerNC No ConnectNIC Network Interface CardNMEA National Marine Electronics AssociationOEM Original Equipment Manufacturer—a company that manufactures a product and sells it to a reseller.OFDMA Orthogonal Frequency Division Multiple AccessOMA DM Open Mobile Alliance Device Management — A device management protocol.OTA ‘Over the air’ (or radiated through the antenna)Table 5-1: Acronyms and definitions (Continued)Acronym or term Definition

Hardware Integration Guide24 Proprietary and Confidential - Contents subject to change 411xxxxPA Power Amplifierpacket A short, fixed-length block of data, including a header, that is transmitted as a unit in a communications network.PCB Printed Circuit BoardPCS Personal Communication SystemA cellular communication infrastructure that uses the 1.9 GHz radio spectrum.PDN Packet Data NetworkPMI Pre-coding Matrix IndexPSS Primary synchronisation signalPST Product Support ToolsPTCRB PCS Type Certification Review BoardQAM Quadrature Amplitude Modulation.This form of modulation uses amplitude, frequency, and phase to transfer data on the carrier wave.QMI Qualcomm MSM/Modem InterfaceQOS Quality of ServiceQPSK Quadrature Phase-Shift KeyingQPST Qualcomm Product Support ToolsRAT Radio Access TechnologyRF Radio FrequencyRI Ring Indicatorroaming A cellular subscriber is in an area where service is obtained from a cellular service provider that is not the subscriber’s provider.RSE Radiated Spurious EmissionsRSSI Received Signal Strength IndicationSDK Software Development KitSED Smart Error DetectionSensitivity (Audio) Measure of lowest power signal that the receiver can measure.Sensitivity (RF) Measure of lowest power signal at the receiver input that can provide a prescribed BER / BLER / SNR value at the receiver output.SG An LTE signaling interface for SMS (“SMS over SGs”)SIB System Information BlockTable 5-1: Acronyms and definitions (Continued)Acronym or term Definition

AcronymsRev 1 Dec.12 Proprietary and Confidential - Contents subject to change 25SIM Subscriber Identity Module. Also referred to as USIM or UICC.SIMO Single Input Multiple Output—smart antenna technology that uses a single antenna at the transmitter side and multiple antennas at the receiver side. This improves performance and security.SISO Single Input Single Output—antenna technology that uses a single antenna at both the transmitter side and the receiver side.SKU Stock Keeping Unit—identifies an inventory item: a unique code, consisting of numbers or letters and numbers, assigned to a product by a retailer for purposes of identification and inventory control.SMS Short Message Service.A feature that allows users of a wireless device on a wireless network to receive or transmit short electronic alphanumeric messages (up to 160 characters, depending on the service provider).S/N Signal-to-noise (ratio)SNR Signal-to-Noise RatioSOF Start of Frame — A USB function.SSS Secondary synchronisation signal.SUPL Secure User Plane LocationTIA/EIA Telecommunications Industry Association / Electronics Industry Association.A standards setting trade organization, whose members provide communications and information technology products, systems, distribution services and professional services in the United States and around the world. Consult www.tiaonline.org.TIS Total Isotropic SensitivityTRP Total Radiated PowerUDK Universal Development Kit (for PCI Express Mini Cards)UE User EquipmentUICC Universal Integrated Circuit Card (Also referred to as a SIM card.)UL Uplink (mobile to network)UMTS Universal Mobile Telecommunications SystemUSB Universal Serial BusUSIM Universal Subscriber Identity Module (UMTS)VCC Supply voltageVSWR Voltage Standing Wave RatioWAN Wide Area NetworkWCDMA Wideband Code Division Multiple Access (also referred to as UMTS)Table 5-1: Acronyms and definitions (Continued)Acronym or term Definition

Hardware Integration Guide26 Proprietary and Confidential - Contents subject to change 411xxxxWLAN Wireless Local Area NetworkZIF Zero Intermediate FrequencyTable 5-1: Acronyms and definitions (Continued)Acronym or term Definition

Rev 1 Dec.12 Proprietary and Confidential - Contents subject to change 27IndexAaccessories, 7acronyms and definitions, 21– 26antennaconnection considerations, 12custom, design, 12diversity antenna, disabling, 13limit, matching coaxial connections, 12location, considerations, 12matching, considerations, 12maximum cable loss, 12routing, 13approvals, regulatory and industry, 17Bbands supported, RFGSM, 11WCDMA, 11Ccable lossantenna, maximum, 12connectiongrounding, 13connectors, requiredhost-module, 7Ddesense. See RFDevelopment Kit contents, 7diversity antennadisabling, 13EEDGEconnector, required, 7Ffiltering, RF desense, 14frequency band supportGSM, 11WCDMA, 11Ggainmaximum, 18groundingconnection considerations, 13GSMfrequency band support, 11Iimpedancemodule–antenna, 13industry approvals, 17interferencedevice generated, 14host-generated, 14wireless devices, 14Mmodulepower states, 9–??Nnoiseleakage, minimizing, 13PPCBmulti-layer, shielding for RF desense, 15powerstates, module, 9–??Rradiated sensitivity measurement, 15radiated spurious emissions, 15regulatory approvals, 17regulatory information, 17– 19FCC, 18limitation of liability, 17safety and hazards, 17

Hardware Integration Guide28 Proprietary and Confidential - Contents subject to change 411xxxxRFantenna cable loss, maximum, 12antenna connection, considerations, 12connectors, required, 7desensedevice-generated, 14harmonic energy, filtering, 14mitigation suggestions, 14shielding suggestions, 14interferenceother devices, 14wireless devices, 14RF bands supportedGSM, 11WCDMA, 11RF specifications, 11–??RSE, 15Ssensitivityradiated measurement, overview, 15shieldingmodule, compliance, 12reducing RF desense, 14SIMconnector, required, 7specificationsRF, 11–??UUDK, 7Universal Development Kit, 7WWCDMAfrequency band support, 11ZZIF (Zero Intermediate Frequency), 13

Navigation menu