Sierra Wireless Q2698 Cellular/PCS GSM/EDGE/WCDMA Modem User Manual AirPrime Q2698 Hardware Integration Guide V0 1x

Download:
Mirror Download [FCC.gov]
Document ID	1787528
Application ID	OGnWcopBgA3kOP4T2fFZiQ==
Document Description	TempConfidential_AirPrime_Q2698_Hardware_Integration_Guide_V3
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.19kB (239868 bits)
Date Submitted	2012-09-11 00:00:00
Date Available	2013-03-13 00:00:00
Creation Date	2012-08-14 12:14:52
Producing Software	Acrobat Distiller 9.2.0 (Windows)
Document Lastmod	2012-08-14 12:14:52
Document Title	Microsoft Word - AirPrime_Q2698_Hardware_Integration_Guide_V0.1.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	rlei

Hardware Integration Guide
AirPrime Q2698
WA_DEV_Q2698_001
June 18, 2011
Hardware Integration Guide
Important Notice
Due to the nature of wireless communications, transmission and reception of data can never be
guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant
delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used
in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used
in situations where failure to transmit or receive data could result in damage of any kind to the user or
any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless
accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or
received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or
receive such data.
Safety and Hazards
Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive
atmospheres may be present, near medical equipment, near life support equipment, or any equipment
which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem
MUST BE POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with
this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on
the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When
operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard
systems.
Note:
Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door
is open. Sierra Wireless modems may be used at this time.
The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of
a vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In
some states and provinces, operating such communications devices while in control of a vehicle is an
offence.
Limitations of Liability
This manual is provided “as is”. Sierra Wireless makes no warranties of any kind, either expressed or
implied, including any implied warranties of merchantability, fitness for a particular purpose, or
noninfringement. The recipient of the manual shall endorse all risks arising from its use.
The information in this manual is subject to change without notice and does not represent a
commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES
SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL,
GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR
REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS
PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY
THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability
arising under or in connection with the Sierra Wireless product, regardless of the number of events,
occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the
Sierra Wireless product.
WA_DEV_Q2698_HWIG
Rev 1.0
JuneJune 18, 2011
Hardware Integration Guide
Patents
This product may contain technology developed by or for Sierra Wireless Inc.
This product includes technology licensed from QUALCOMM® 3G.
This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents
licensed from InterDigital Group.
Copyright
© 2011 Sierra Wireless. All rights reserved.
Trademarks
AirCard® and Watcher® are registered trademarks of Sierra Wireless. Sierra Wireless™, AirPrime™,
AirLink™, AirVantage™ and the Sierra Wireless logo are trademarks of Sierra Wireless.
, ®, inSIM®, WAVECOM®, WISMO®, Wireless Microprocessor®,
Wireless CPU , Open AT are filed or registered trademarks of Sierra Wireless S.A. in France and/or
in other countries.
®
®
Windows® and Windows Vista® are registered trademarks of Microsoft Corporation.
Macintosh and Mac OS are registered trademarks of Apple Inc., registered in the U.S. and other
countries.
QUALCOMM® is a registered trademark of QUALCOMM Incorporated. Used under license.
Other trademarks are the property of the respective owners.
Contact Information
Sales Desk:
Post:
Fax:
Web:
Phone:
1-604-232-1488
Hours:
8:00 AM to 5:00 PM Pacific Time
E-mail:
sales@sierrawireless.com
Sierra Wireless
13811 Wireless Way
Richmond, BC
Canada
V6V 3A4
1-604-231-1109
www.sierrawireless.com
Consult our website for up-to-date product descriptions, documentation, application notes, firmware
upgrades, troubleshooting tips, and press releases: www.sierrawireless.com
WA_DEV_Q2698_HWIG
Rev 1.0
JuneJune 18, 2011
Hardware Integration Guide
Document History
Version
Date
Updates
001
June 18, 2012
Creation
WA_DEV_Q2698_HWIG
Rev 1.0
JuneJune 18, 2011
Contents
1. INTRODUCTION .................................................................................................. 7
1.1.
Hardware Development Components ...............................................................................7
2. POWER INTERFACE ........................................................................................... 8
2.1.
Power Supply ....................................................................................................................8
2.2.
Electrostatic Discharge (ESD) ...........................................................................................8
2.3.
Power States .....................................................................................................................9
3. RF INTEGRATION ............................................................................................. 10
3.1.
Supported RF Bands .......................................................................................................10
3.1.1.
Ground Connection Guidelines ................................................................................11
3.1.2.
Shielding Guidelines ................................................................................................11
3.2.
Antenna Guidelines .........................................................................................................11
3.2.1.
Choosing the Correct Antenna and Cabling ............................................................11
3.2.2.
Determining the Antenna’s Location ........................................................................11
3.3.
RF Desense Sources ......................................................................................................12
4. AUDIO INTERFACE ........................................................................................... 13
5. REGULATORY INFORMATION......................................................................... 14
5.1.
Important Notice ..............................................................................................................14
5.2.
Safety and Hazards .........................................................................................................14
5.3.
Important Compliance Information for North American Users ........................................15
6. REFERENCES ................................................................................................... 17
6.1.
Reference Documents.....................................................................................................17
6.2.
List of Abbreviations ........................................................................................................17
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
List of Tables
Table 1.
Power Supply Requirements ............................................................................................. 8
Table 2.
ESD Specifications ............................................................................................................ 8
Table 3.
Supported Q2698 Power States........................................................................................ 9
Table 4.
Supported Frequency Ranges ........................................................................................ 10
Table 5.
PCM Audio Interface Features ........................................................................................ 13
Table 6.
Audio Pin Description ...................................................................................................... 13
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
1. Introduction
The Sierra Wireless AirPrime Q2698 soldered-down module forms the radio component for the
products in which it is embedded.
Module-specific performance and physical characteristics are described in the corresponding product
specification document.
Note:
An understanding of network technology, and experience in integrating hardware components into
electronic equipment is assumed.
1.1.
Hardware Development Components
Sierra Wireless manufactures two hardware development components to facilitate the hardware
integration process:

AirPrime Delelopment kit for Q26 on which an Q2698 module is embedded. This board may
be used as a stand-alone platform for basic hardware development.

AirPrime Q26 Development Kit – Hardware development board on which an Q26 module is
plugged.. The development kit provides access to all of the interfaces supported by the Q26
module.
For instructions on using theQ26 Development Kit, see document [1] Universal Development Kit User
Guide for AirPrime Q26 Series.
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
2. Power Interface
2.1.
Power Supply
The host device must provide power to the AirPrime soldered-down module over pins 1, 2, 3 and 4
(VCC_3V6) as detailed in the following table.
Table 1.
Power Supply Requirements
Requirement Type
Value
Power Supply
3.8V (nominal)
Voltage Range (VMIN – VMAX)
3.4V – 4.2V
Current (instantaneous (5ms))
3A
Current (continuous)
700mA
Note:
The host must provide safe and continuous power to the module; the module does NOT have
protection circuits to guard against electrical overstress.
2.2.
Electrostatic Discharge (ESD)
The host device must provide adequate ESD protection on digital circuits and antenna ports as
detailed in the following table.
Note:
Table 2.
The level of protection required depends on the application.
ESD Specifications
Category
Connection
Specification
Operational
RF ports
IEC-61000-4-2 — Level (Electrostatic Discharge Immunity
Test)
Non-operational
Host connector interface
Unless otherwise specified:
Signals
USIM connector
Other host signals
WA_DEV_Q2698_HWIG
Rev 001

JESD22-A114 +/- 2kV Human Body Model

JESD22-A115 +/- 200V Machine Model

JESD22-C101C +/- 500V Charged Device Model
ESD protection is highly recommended at the point where
the USIM contacts are exposed, and for any other signals
that would be subjected to ESD by the user.
June 18, 2011
Hardware Integration Guide
2.3.
Power Interface
Power States
The Q2698 module has five power states as detailed in the following table.
Table 3.
Supported Q2698 Power States
State
Description
Host
Powered
Module
Powered
USB
Interface
Active
RF
Enabled




















 Capable of placing / receiving calls or
establishing data connections on
network
 USB interface is fully active
Normal
(Default state)
 Current consumption in a call or data
connection is affected by:
 Radio band in use
 Tx power
 Receive gain settings
 Data rate
 Number of active Tx time slots
 ‘Airplane’ mode — Rx / Tx are disabled;
USB interface is active
Airplane
Mode (RF off)
Sleep (Idle
Mode)
 State entered automatically when
critical voltage / temperature thresholds
are exceeded. Host should consider
powering off module to prevent damage
to unit.
 Normal state of module between calls
or data connections.
 Module cycles between wake (polling
the network) and sleep, at network
provider-determined interval.
 Host power is connected
Off
Disconnected
 Module is powered down (drawing
minimal current from host power
supply)
 Host power is disconnected from
module
 All module-related voltages are at 0V
WA_DEV_Q2698_HWIG
Rev 1.0
JuneJune 18, 2011
3. RF Integration
3.1.
Supported RF Bands
Table 4.
Supported Frequency Ranges
Band
Frequencies (MHz)
Q2698
GSM 850
Transmit: 824 – 849
Receive: 869 – 894

EGSM 900
Transmit: 880 – 915
Receive: 925 – 960

DCS 1800
Transmit: 1710 – 1785
Receive: 1805 – 1880

PCS 1900
Transmit: 1850 – 1910
Receive: 1930 – 1990

Band I
WCDMA 2100
Transmit: 1920 – 1980
Receive: 2110 – 2170

Band II
WCDMA 1900
Transmit: 1850 – 1910
Receive: 1930 – 1990

Band V
WCDMA 850
Transmit: 824 – 849
Receive: 869 – 894

Band VI
WCDMA 800
Transmit: 830 – 840
Receive: 875 – 885

Band VIII
WCDMA 900
Transmit: 880 – 915
Receive: 925 – 960

GSM Bands
WCDMA Bands
WCDMA Bands RX Diversity
Band I
WCDMA 2100
Transmit: 1920 – 1980
Receive: 2110 – 2170

Band II
WCDMA 1900
Transmit: 1850 – 1910
Receive: 1930 – 1990

Band V
WCDMA 850
Transmit: 824 – 849
Receive: 869 – 894

Band VI
WCDMA 800
Transmit: 830 – 840
Receive: 875 – 885

Band VIII
WCDMA 900
Transmit: 880 – 915
Receive: 925 – 960


GPS
GPS

1575.42
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
10
Hardware Integration Guide
3.1.1.
RF Integration
Ground Connection Guidelines
When connecting the module to system ground:

Prevent noise leakage by establishing a very good ground connection to the module through
the host connector.

Minimize ground noise leakage into the RF.
Depending on the host board design, noise could potentially be coupled to the module from
the host board. This is mainly an issue for host designs that have signals traveling along the
length of the module, or circuitry operating at both ends of the module interconnects.
3.1.2.
Shielding Guidelines
The module is fully shielded to protect against EMI and to ensure compliance with FCC Part 15 “Radio Frequency Devices” (or equivalent regulations in other jurisdictions).
Note:
This shielding must NOT be removed.
3.2.
Antenna Guidelines
3.2.1.
Choosing the Correct Antenna and Cabling
Consider the following points for appropriate antenna selection:

The antenna (and associated circuitry) should have a nominal impedance of 50Ω with a return
loss of better than 10 dB across each frequency band of operation.

The system gain value affects both radiated power and regulatory (FCC, IC, CE, etc.) test
results.
3.2.2.
Determining the Antenna’s Location
Consider the following points when deciding where to place the antenna:

Antenna location may affect RF performance. Although the module is shielded to prevent
interference in most applications, the placement of the antenna is still very important—if the
host device is insufficiently shielded, high levels of broadband or spurious noise can degrade
the module’s performance.

Connecting cables between the module and the antenna must have 50Ω impedance. If the
impedance of the module is mismatched, RF performance is reduced significantly.

Antenna cables should be routed, if possible, away from noise sources (switching power
supplies, LCD assemblies, etc.). If the cables are near the noise sources, the noise may be
coupled into the RF cable and into the antenna.
WA_DEV_Q2698_HWIG
Rev 1.0
JuneJune 18, 2011
11
Hardware Integration Guide
3.3.
RF Integration
RF Desense Sources
Common sources of interference that may affect the module’s RF performance (RF desense) include

Power supply noise
 Can lead to noise in the RF signal
 Module power supply ripple limit <= 100 mVp-p 1 Hz–100 kHz

Interference from other embedded wireless devices
 Any harmonics, sub-harmonics, or cross-products of signals that fall in the module’s Rx
range may cause spurious response, resulting in decreased Rx performance.
 Tx power and corresponding broadband noise may overload or increase the noise floor of
the module’s receiver, resulting in RF desense.
 Severity of interference depends on proximity of other antennas to the module’s antennas.

Host electronic device-generated RF
 Proximity of host electronics to the module’s antenna can contribute to decreased Rx
performance.
 Some devices include microprocessor and memory, display panel and display drivers,
and switching mode power supplies.
Note:
In practice, there are usually numerous interfering frequencies and harmonics. The net effect can
be a series of desensitized receive channels.
WA_DEV_Q2698_HWIG
Rev 1.0
JuneJune 18, 2011
12
4. Audio Interface
The AirPrime Q2698 embedded module only supports digital audio interface (PCM) as summarized in
the following tables. Refer to document [2] AirPrime Q2698Product Technical Specification and
Customer Design Guidelines for detailed information about the digital audio interface.
Table 5.
PCM Audio Interface Features
Feature
Details
Implementation
Primary PCM supported to interface with external codec
Power
1.8 V (use VREF_1V8 as logic reference)
Features

IOM-2 compatible device on physical level

Master mode only with 16 slots by frame (user only on slot 0)

Bit rate single clock mode at 2.048 MHz

16 bits data word MSB first only

Linear Law only (no compression law)

Long Frame Synchronization only

Push-pull configuration on PCM-OUT and PCM-IN
Table 6.
Audio Pin Description
Pin #
Signal Name
Description
Notes
8 kHz
64
PCM_SYNC
PCM synchronization bit
65
PCM_DOUT
PCM output
66
PCM_DIN
PCM input
67
PCM_CLK
PCM clock
WA_DEV_Q2698_HWIG
Rev 001
2.048 MHz for primary PCM mode
June 18, 2011
13
5. Regulatory Information
5.1.
Important Notice
Because of the nature of wireless communications, transmission and reception of data can never be
guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant
delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used
in a normal manner with a well constructed network, the Sierra Wireless modem should not be used in
situations where failure to transmit or receive data could result in damage of any kind to the user or
any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless
and its affiliates accept no responsibility for damages of any kind resulting from delays or errors in
data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless
modem to transmit or receive such data.
5.2.
Safety and Hazards
Do not operate your AirPrime Q2698 modem:

In areas where blasting is in progress

Where explosive atmospheres may be present including refueling points, fuel depots, and
chemical plants

Near medical equipment, life support equipment, or any equipment which may be susceptible
to any form of radio interference.
In such areas, the Q2698 modem MUST BE POWERED OFF. Otherwise, the Q2698 modem can
transmit signals that could interfere with this equipment. In an aircraft, the Q2698 modem MUST BE
POWERED OFF. Otherwise, the Q2698 modem can transmit signals that could interfere with various
onboard systems and may be dangerous to the operation of the aircraft or disrupt the cellular network.
Use of a cellular phone in an aircraft is illegal in some jurisdictions. Failure to observe this instruction
may lead to suspension or denial of cellular telephone services to the offender, or legal action or both.
Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is
open. The Q2698 modem may be used normally at this time.
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
14
Hardware Integration Guide
5.3.
Regulatory Information
Important Compliance Information for North
American Users
The Q2698 modem has been granted modular approval for mobile applications. Integrators may use
the Q2698 modem in their final products without additional FCC/IC (Industry Canada) certification if
they meet the following conditions. Otherwise, additional FCC/IC approvals must be obtained.
1. At least 20 cm separation distance between the antenna and the user’s body must be
maintained at all times.
2. To comply with FCC/IC regulations limiting both maximum RF output power and human
exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only
exposure condition must not exceed 7.5 dBi in the cellular band and 3.5 dBi in the PCS band
for the Q2698.
3. The Q2698 modem and its antenna must not be co-located or operating in conjunction with
any other transmitter or antenna within a host device.
4. The RF signal must be routed on the application board using tracks with a 50Ω characteristic
impedance.
Basically, the characteristic impedance depends on the dielectric, the track width and the
ground plane spacing.
In order to respect this constraint, Sierra Wireless recommends using MicroStrip or StripLine
structure and computing the Tracks width with a simulation tool (like AppCad shown in the
figure below and that is available free of charge at http://www.agilent.com).
If a multi-layered PCB is used, the RF path on the board must not cross any signal (digital,
analog or supply).
If necessary, use StripLine structure and route the digital line(s) "outside" the RF structure as
shown in the figure below.
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
15
Hardware Integration Guide
Regulatory Information
Stripline and Coplanar design requires having a correct ground plane at both sides.
Consequently, it is necessary to add some vias along the RF path.
It is recommended to use Stripline design if the RF path is fairly long (more than 3cm), since
MicroStrip design is not shielded. Consequently, the RF signal (when transmitting) may
interfere with neighbouring electronics (AF amplifier, etc.). In the same way, the neighbouring
electronics (micro-controllers, etc.) may degrade the reception performances.
The GSM/GPRS connector is intended to be directly connected to a 50Ω antenna and no
matching is needed.
5. A label must be affixed to the outside of the end product into which the Q2698 modem is
incorporated, with a statement similar to the following for Q2698:
This device contains FCC ID: N7NQ2698
This equipment contains equipment certified under IC: 2417C-Q2698
6. A user manual with the end product must clearly indicate the operating requirements and
conditions that must be observed to ensure compliance with current FCC/IC RF exposure
guidelines.
The end product with an embedded Q2698 modem may also need to pass the FCC Part 15
unintentional emission testing requirements and be properly authorized per FCC Part 15.
Note:
If this module is intended for use in a portable device, you are responsible for separate approval to
satisfy the SAR requirements of FCC Part 2.1093 and IC RSS-102.
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
16
6. References
6.1.
[1]
Reference Documents
Universal Development Kit User Guide for AirPrime Q26 Series
Reference: User Guide for AirPrime Q26 Series Development Kit-Rev8.0
[2]
AirPrime Q2698Product Technical Specification and Customer Design Guidelines
Reference: Product Technical Specification and Customer Design Guidelines for AirPrime
Q2698-Rev2.0
6.2.
List of Abbreviations
Acronym or Term
Definition
AGC
Automatic Gain Control
BER
Bit Error Rate - a measure of receive sensitivity
BLER
Block Error Rate
Call Box
Base Station Simulator - Agilent E8285A or 8960, Rohde & Schwarz CMU200
CDMA
Code Division Multiple Access
dB
Decibel = 10 x log10 (P1/P2)
P1 is calculated power; P2 is reference power
Decibel = 20 x log10 (V1/V2)
V1 is calculated voltage, V2 is reference voltage
dBm
Decibels, relative to 1 mW - Decibel(mW) = 10 x log10 (Pwr (mW)/1mW)
DUT
Device Under Test
EDGE
Enhanced Data rates for GSM Evolution
EM
Embedded Module
ESD
ElectroStatic Discharge
FER
Frame Error Rate - a measure of receive sensitivity
GPRS
General Packet Radio Services
GPS
Global Positioning System
GSM
Global System for Mobile communications
Hz
Hertz = 1 cycle/second
inrush current
Peak current drawn when a device is connected or powered on
IS-2000
3G radio standards for voice and data (CDMA only)
IS-95
2G radio standards targeted for voice (cdmaONE)
LDO
Low Drop Out - refers to linear regulator
MHz
MegaHertz = 10E6 Hertz (Hertz = 1 cycle/second)
MIO
Module Input/Output
MPE
Maximum Permissible Exposure—the level of radiation to which a person may be
exposed without hazardous effect or adverse biological changes
OTA
Over-The-Air or Radiated through the antenna
PCS
Personal Communication System - PCS spans the 1.9 GHz radio spectrum
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
17
Hardware Integration Guide
References
Acronym or Term
Definition
RF
Radio Frequency
RMS
Root Mean Square
SA
Selective Availability
Sensitivity (Audio)
Measure of lowest power signal that the receiver can measure
Sensitivity (RF)
Measure of lowest power signal at the receiver input that can provide a prescribed
BER/BLER/SNR value at the receiver output.
SIM
Subscriber Identity Module
Q2698
Sierra Wireless AirPrime soldered-down module used on GSM/UMTS networks
SNR
Signal to Noise Ratio
SOF
Start of Frame - a USB function
UART
Universal Asynchronous Receiver Transmitter
UMTS
Universal Mobile Telecommunications System
USB
Universal Serial Bus
USIM
Universal Subscriber Identity Module
VCC
Supply voltage
WCDMA
Wideband Code Division Multiple Access—In this document, the term “UMTS” is
used instead of “WCDMA”.
XIM
In this document, XIM is used as part of the contact identifiers for the USIM interface
(XIM_VCC, XIM_CLK, etc.).
WA_DEV_Q2698_HWIG
Rev 001
June 18, 2011
18

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : rlei
Create Date                     : 2012:08:14 12:14:52+08:00
Modify Date                     : 2012:08:14 12:14:52+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - AirPrime_Q2698_Hardware_Integration_Guide_V0.1.docx
Creator                         : rlei
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Document ID                     : uuid:df729a61-e31a-4688-8844-1dfc7ff62ff8
Instance ID                     : uuid:a036b155-87dd-43b8-9b14-e0c4a6b11071
Page Count                      : 18

EXIF Metadata provided by EXIF.tools