Sigma Designs SG-ZIRC3502 Z-Wave & Infra Red Remote Control User Manual
Sigma Designs Inc Z-Wave & Infra Red Remote Control
User Manual.pdf
ZIRC-SD3502 Z-Wave AV / IR Remote Control ZIRC-SD3502 Z-Wave & IR Remote Control User’s Manual All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control CONTENTS 1. INTRODUCTION ..........................................................................................................................3 2. USAGE ........................................................................................................................................4 2.1 Z-Wave Network Overview .....................................................................................................4 2.2 Initial Inclusion .......................................................................................................................4 2.3 Audio Video control ................................................................................................................4 2.4 Low battery ............................................................................................................................7 2.5 Subsequent Inclusion/Exclusion ..............................................................................................7 2.6 Reset ......................................................................................................................................7 2.7 Enable Over-The-Air firmware upgrade ...................................................................................7 2.8 Send Node Info .......................................................................................................................8 2.9 Wake up .................................................................................................................................8 2.10 Update Associations ...............................................................................................................8 2.11 Test mode...............................................................................................................................8 2.11.1 Carrier frequency ................................................................................................................8 2.11.2 Response to HomeID 0 ........................................................................................................8 3. FCC NOTICE TO USERS .................................................................................................................9 4. EU DECLARATION OF CONFORMITY........................................................................................... 10 All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control 1. INTRODUCTION ZiRC is a low cost Remote Control reference design based on the SD3502 for dual-mode, Z-Wave and InfraRed (IR), control of Sigma Designs Internet Television (IPTV) Set Top Boxes (STB). User feedback is through a tricolor LED (red, green, amber) located next to the power button. As a Z-Wave device it can interwork with any other Z-Wave certified device from any vendor. ZiRC can control the STB both in IR mode and in Z-Wave AV mode. The IR mode is using NEC format with a target address of 0xCB04. On first power up, the ZiRC is in Z-Wave AV (Audio Video) mode. While the IR mode can be used immediately, the ZiRC mode requires the remote to be included into the STB’s Home Area Network first. From time to time, this manual may refer to STB operations that are not covered in this document, but rather in the STB’s manual. Figure 1: ZiRC All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control 2. USAGE ZiRC is a low cost Remote Control reference design based on the SD3502 for dual-mode, Z-Wave and InfraRed (IR), control of Sigma Designs Internet Television (IPTV) Set Top Boxes (STB). User feedback is through a tricolor LED (red, green, amber) located next to the power button. As a Z-Wave device it can interwork with any other Z-Wave certified device from any vendor. 2.1 Z-Wave Network Overview Z-Wave® is an interoperable, lightweight wireless technology that empowers both consumers and manufacturers with an ecosystem of products that work together. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All constantly powered nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. 2.2 Initial Inclusion To start using a newly acquired ZiRC, set the STB into inclusion mode. Insert 2 AAA batteries as indicated in the battery compartment of the ZiRC. Any button press on the ZiRC will start learn mode. While in learn mode, the LED will blink amber every 3 seconds. After a few seconds, the LED should blink green 3 times on success or red on failure. Any button press would exit the inclusion mode with failure. After successful inclusion, the ZiRC waits 10 seconds for any association to be set up during which time the LED should blink amber every 3 seconds. If any association was successfully set up during this time, it will blink green thrice. Otherwise any button press or timeout would exit the association mode with the LED blinking red thrice. After this process the ZiRC goes to sleep and is now ready to control the STB. After any successful exclusion or reset operation, any button press will enter inclusion mode. 2.3 Audio Video control To switch the ZiRC between Z-Wave AV and IR mode, press & hold SETUP+RED for 1 second. The ZiRC remembers the mode it is in even when its batteries are replaced. On entering IR mode, the LED will blink amber once. All button presses are acknowledged by a single amber blink, as there is no feedback from the STB for IR. Note that while in IR mode, only the switch mode combo will work and all other combos are ignored. All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control On entering Z-Wave AV mode, the LED will blink green once. In this mode, successful AV commands sent to the STB are indicated by a single green LED blink. While the button is kept depressed, keep alive is sent every 200 milliseconds and the LED will continue to blink green accordingly. Pressing SETUP+PLAY or SETUP+STOP will send a Basic ON or OFF respectively to turn on and off any ZWave equipment that is not AV capable. In Z-Wave AV mode the buttons are mapped as in the table below. All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control Table 1: Button Mapping Button / IR code Z-Wave AV code ON_OFF 0x0027 FILE_MODE 0x017E SETUP 0x0115 SUSPEND 0x0194 PAGEUP 0x0022 USB_DVDROM_EJECT 0x0091 TV_MODE 0x017C MUTE 0x0001 PAGE_DOWN 0x0023 BT_1 0x0007 BT_2 0x0008 BT_3 0x0009 BT_4 0x000A BT_5 0x000B BT_6 0x000C BT_7 0x000D BT_8 0x000E BT_9 0x000F DELETE 0x007D BT_0 0x0006 CAPS_NUM 0x017B RETURN 0x004B UP 0x001E SOURCE 0x017D LEFT 0x0020 ENTER 0x0024 RIGHT 0x0021 INFO 0x017A DOWN 0x001F HOME 0x00AF MENU 0x001D PREV 0x011C PLAY 0x0013 NEXT 0x011B TITLE 0x0156 All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control REV STOP FWD REPEAT ANGLE PAUSE SLOW TIME_SEEK AUDIO SUBTITLE ZOOM RED GREEN YELLOW BLUE 0x0017 0x0014 0x0016 0x0107 0x003C 0x0015 0x011E 0x017F 0x0041 0x0130 0x0169 0x009D 0x009B 0x009F 0x009A 2.4 Low battery When battery is low, any key press will be immediately followed by 3 red LED blinks. This is an indication to replace batteries. This replaces the normal LED indications described in this document. 2.5 Subsequent Inclusion/Exclusion Set the STB to add or remove the remote control as required. Press & hold SETUP+HOME for 5 seconds. The LED should blink green once to signal it has entered learn mode, at which point the use may release the buttons. The LED should blink 3 times green on success or red on failure. 2.6 Reset Press & hold SETUP+RETURN for 10 seconds. The LED should blink green once on success. This will restore ZIRC to factory default setting. 2.7 Enable Over-The-Air firmware upgrade Press & hold SETUP+ENTER for 5 seconds. The LED will start to blink amber and the firmware upgrade can start. If the firmware is transferred successfully the LED will blink GREEN 3 times. If the firmware upgrade fails the LED will blink RED 3 times and a retry must be done. All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control 2.8 Send Node Info Some devices set up automatic associations on receiving a Z-Wave Node Information Frame (NIF) from the target device. For this purpose, pressing & holding SETUP+INFO for 3 seconds will cause the LED to blink green once and send out the NIF once. This feature is also a requirement for Z-Wave certification. 2.9 Wake up To conserve power, the ZiRC remains asleep until a key is pressed after which it goes back to sleep after 3 seconds. To enable the ZiRC to stay awake for an extended period of time and to notify that it has woken up so as to carry out any configuration, press & hold SETUP+YELLOW for 5s. The LED should blink green once to signal it has woken up and notified the STB, at which point the user may release the buttons. The remote stays awake for 10 seconds only during which time the LED will blink amber every 3 seconds. 2.10 Update Associations From time to time, the STB may create associations with other STBs to allow simultaneous control from one remote control. Wake the remote up as described in 2.7. Note that wake up time is extended only by association commands received from the STB. So quickly set the STB to update the associations. The LED should blink green thrice on successful association. The process is terminated by any button press or timeout with the LED blinking red thrice. If no associations are set up, the ZiRC will control the controller that added it to the network. Otherwise it will target all the nodes in the group. 2.11 Test mode This is not a normal user function but rather an advanced function used for testing. When the remote is in test mode the green led will keep flashing every second. The remote exits test mode after 60 seconds. 2.11.1 Carrier frequency Press FILE+PGUP+ZOOM+PAUSE and hold for 10s. 2.11.2 Response to HomeID 0 Press FILE+PGUP+REV+MENU and hold for 10s. All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control 3. FCC NOTICE TO USERS Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: FCC Caution Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control 4. EU DECLARATION OF CONFORMITY EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN 60950-1: 2006/A12: 2011 Safety of Information Technology Equipment EN 300 220-1/-2 V2.4.1 (2012-05) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels EN 301 489-1 V1.9.2 (2011-09) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-3 V1.4.1: (2002) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range EN 62479: 2010 Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz 0560 Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma malħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc. ZIRC-SD3502 Z-Wave AV / IR Remote Control Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2012 Sigma Designs, Inc.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Annotate, Fill forms XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2013:08:14 10:51:58Z Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2013:08:22 15:51:51+08:00 Metadata Date : 2013:08:22 15:51:51+08:00 Format : application/pdf Creator : GQuat Title : Microsoft Word - 8. ZiRC-SD3502 New User Manual D02.doc Producer : GPL Ghostscript 8.15 Document ID : uuid:7a96e604-7d83-48b2-b6b6-e4e2f00801a4 Instance ID : uuid:903c5514-401d-476f-a388-eb4c9b0a1e47 Page Count : 12 Author : GQuatEXIF Metadata provided by EXIF.tools