Signal Communications SCVT-000125 TeleEye Pro Unit User Manual

Download:
Mirror Download [FCC.gov]
Document ID	92553
Application ID	h67c0MXq+LB/2YGn5umezg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.16kB (627043 bits)
Date Submitted	2000-03-22 00:00:00
Date Available	2000-03-29 00:00:00
Creation Date	2000-03-20 17:34:51
Producing Software	Acrobat 4.0 Scan Plug-in for Windows
Document Lastmod	2000-03-20 17:35:04
Document Title	User Manual
Document Creator	Acrobat 4.0 Scan Plug-in for Windows

TeIeEye 73:30
Transmission Unit
PTA-B1 l PTA-C1!
User Guide
Page]
Notice:
Signal Communications Limited reserves the right to make improvements to the
product described in this manual at any time and without notice.
This manual is copyrighted, All rights are reserved. This manual may not be copied,
reproduced or translated in whole or part without prior consent fi'om Signal
Communications Limited
Third party trademarks are the property of their respective holders.
Copyright (0) 1995-98 Signal Communications Limited-
All rights reserved.
Version 2.6
Limits of Liability and Disclaimer of Warranty
Signal Communications Limited have taken care in preparation of this manual, but
makes no expressed or implied warranty of any kind and assume no responsibility for errors or
omissions No liability is assumed for incidental or consequential damages in connection with or
arising out of the use of the infon‘nation or accessories contained herein.
FCC Statement on Class B
WARNING
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determine by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
0 Reorient or relocate the receiving antenna.
e Increase the separation between the equipment and receiver.
0 Connect the equipment into an outlet on a circuit different from that to
which the receiver is needed.
0 Consult the dealer or an experienced radio/T V technician for help.
Shielded cables must be used with this unit to ensure compliance with the
Class B FCC limits.
Table of Contents
SECTION 1
INTRODUCTION
SECTION 2
INSTALLING TeIeEjte fig
What You Need
System Connections
Sofiware Installation
Registering the Transmission Unit
Connecting re/eWin to TeIeEye %
Alarm P011 Definition
Pin Definitions for Null Modem Cable
Transmitter Unit
SECTION 3
SPECIFICATIONS
Model: PTA-Bl and PTA-CI
ox
-—-\o~c\oonoo\1
11
SECTION
—1
INTRODUCTION
Te/eEye fin is an advanced Video Monitoring System. The transmission
unit is especially designed for monitoring medium sized firm, factory and
warehouse. Four models are available to suit for different applications. PTA-B1 is
monitoring systems transmitting B/W video frames. PTA-C1 functions as
standard model for the transmission of color video. PTA-B1 and PTA-C1
supports up to 4 alarm inputs and 1 output switch.
Features
Transmits high quality Videos of multiple CCTV cameras
Achieves fast video update by using an interframe image compression
Password protection on connections and settings
Built-in real time clock
Multiple alarm inputs with independent NC / NO trigger contacts
Remote control through I relay switch
About the Reception Software
The Te/ern Reception Software is a Win95 application program (IBM or
compatible PC). It implements the system controls as well as image decoding of
the Te/eEye 'Pn systems. The compressed data are decoded and displayed
through the PC monitor.
PageS
SECTION 2
lNSTALLlNG Te/eEye 7)”
What You Need
To install and operate the Te/eEye We transmission unit, the following
items are required:
. TeleEye 2» Transmission Unit
The image transmitter supports up to 4 video sources in all PAL or
NTSC format.
. CCD Camera
Color / monochrome, PAL or NTSCA
. Coaxial Cable (RG—59 recommended)
It is used to connect the video output of the CCD camera to the video
input of Te/eEye We transmission unit.
, Null Modem] Cable
It is used to connect the Te/eEye 'Pn transmission unit to one of the
COM port ofthe PC.
Pageé
System Connections
“MAM”
“harm-z T:
WW“,
IBM Compatible
Recommended Setug Procedures:
step 1: Plug one end of the Null Modem cable into the socket marked MODEM on the
TeIeEye 7714 transmitter, fiten plug the other end to the COM port of the
computer.
Step 2: Plug one end at the BNC cable into the VIDEO OUTPUT of the CCD camera,
then plug the other end to the re/eEye 7” 's VIDEO INPUT connector (CH1
preferred)
If more than one camera. plug the BNC cable to the TeleEye ’Pn CH: to CH4
sequentially/r
step 3: Plug one end of the alarm cable into the connector of the alarm sensor and plug
the other end of the cable to the appropriate pins of the ALARM CONNECTOR
of the Te/eEye ‘Pn ,
step 4: Plug the round end of the ac adaptor into the socket marked POWER on the
reIeEye 73:4 transmitter. (Note: transmitter can support 9V d.c. to 12V d.c.
supply voltage)
step 5: Plug the ac adapter to ac power source and switch on the TelsEye 'Pn.
The TeIaEyo ‘Pn ‘s LED should light up.
Page7
Software Installation
Before setting up Te/eWin, please change the video setting to 800 x 600 true
colour or 16-bit high colour in Win95’s Display Properties
TeIeWin software contains an installation program, SETUP.EXE~ Please use this
program to setup the necessary files into the hard disk of the reception unit.
Once you have completed the following installation procedure, you can run
TeIeWin directly from your hard disk.
Registering the Transmission Unit
Before connecting to the transmission unit, you have to perform transmission unit
registration. This can be done under the Transmitter menu. Transmission unit
registration is required only once; all the information will be recorded in the hard
disk.
In the package, you are provided with a Registration Code and a Serial Number of
the transmission unit. You need to fill them in the Registration Message Box as
shown below. Besides, please keep them in a safe place for fixture reference.
Hmunmum.
1 E Burr n
Connecting TeIeWin to TeIeEye ”Pm
Stepl: Make sure you video setting of Win95 environment is 800 x 600 true colour
or 800 x 600 16—bit High Colour. To start Te/qmn Reception Software,
click on the Start button on the taskbar, then choose Programs _>
TeleEye $1» _> TeIeEye We WRS-AD-l.
Step2: To connect to the TeleEye 7m , click Connect under the Connection menu or
the Connect icon.
Step3: In the Connect Using box, 531°“ Direct to COM] 01' Direct to COM2. That
is the COM port that the null modem cable is physically connecting to.
Step4: Fill in the password in order to connect. The default password is 000000.
StepS: You may now click the connect button to make connection.
You may disconnect the connection by selecting Disconnect on the Connections menu
or clicking the Disconnect button
You may reset the alarms by clicking Reset Alarm under the Alarm menu and fill in the
password The default password is 000000
Pin Definitions of NULL MODEM CABLE
‘ _ _ TeleEye7ho PC PC
Pm definitions Ofa Transmission Unit D325 DB9
DB-9 (female) to 2 RXD M TXD 2 3
DB-ZS (female) or 3 TXD M RXD 3 2
DB-9 (female) to 1 CD % DTR 20 4
DB-9 (female) null 4 DTR % CD 8 1
modem cable 5 GND % GND 7 5
7 RTS M CTS 5 8
8 CTS F) RTS 4 7
Page9
Transmission Unit
The panels of the Te/eEye 'PM transmission unit are shown below :
Front Panel
Functional Description
fig mgr, mun *
cm rm‘ Du
crw mm meR
u: vzv
Rear Panel for PTA-BI and PTA-CI
VIDEO IN Connectors gCHl — CHQ
- Standard BNC connectors for the video sources
— A composite video signal should be supplied to these connectors
ALARM IN Connector
- This connector is used for connecting 1 remote control switches and 4 alarm
inputs.
- All alarm channels have the same priority
Communication Port
A DB~9 male connector for connecting to COM port of PC
Power Connector
A 2,lmm DC power jack for the connection to the power supply (9V—12V DC)
Power Switch
A on/off switch of powerr
Page 1 0
SECTION 3
SPECIFICATIONS
MODEL PTA-Cl PTA-B1
STANDARD (P): PAIJCCIR1 625 LINES, 50 FELDS PER SECOND
(N): NTSC/EIA, 525 LINES, 60 FIELDS PER SECOND
INTERFACE 4 CHANNELS, 1.0V,,P COIVH’OSITE,
BNC WITH 750 TERMINATION
RESOLUTION (H x V) 256 x 192 PIXELS
GRAY LEVELS 256
I6 WLION
COLORS SCALEABLE ADAPTIVE IMAGE COMPRESSION
INPUT 4 INDEPENDENT CHANNELS, NC / NO
OUTPUT I CHANNEL, DRY CONTACT
CONTACT RATING: 24Vac 2A
RESISTIVE LOAD 124Vdc, 2A
TYPE RS- 232C DB 9 MALE CONNECTOR
RATE 38, 400 BITS PER SECOND
FORMAT ASYNCHRONOUS, 8 DATA BITS, NO PARJTY, I STOP BIT
,8,]
FLOW CONTROL HARDWARE RTS, CTS
PROTOCOL EFFICIENT ERROR CONTROL PROTOCOL
MODEM CONTROL HAYES COMMANDS
INPUT VOLTAGE 9 - 12V DC
POWER CONSUIVR’TION 12W igfii.)
AMBLENT +5°C TO +40°C
TEMPERATURE (40°C TO 104°F)
RELATIVE HU'NEDITY 20% TO 85%, NO CONDENSATION
DIMENSION (W x D x H) 254mm x 203mm x 38mm
COLOR DARK GRAY
WEIGHT 1,3kg
Page] 1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2000:03:20 17:35:04+08:00
Create Date                     : 2000:03:20 17:34:51+08:00
Creator                         : Acrobat 4.0 Scan Plug-in for Windows
Producer                        : Acrobat 4.0 Scan Plug-in for Windows
Page Count                      : 11

EXIF Metadata provided by EXIF.tools