Signal Communications SCVT-000126 TeleEye Pro User Manual

Download:
Mirror Download [FCC.gov]
Document ID	92572
Application ID	ZNDIztU5beWZqisoFymY5w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.47kB (318386 bits)
Date Submitted	2000-03-22 00:00:00
Date Available	2000-03-29 00:00:00
Creation Date	2000-03-20 17:07:16
Producing Software	Acrobat 4.0 Scan Plug-in for Windows
Document Lastmod	2000-03-20 17:07:34
Document Title	User Manual
Document Creator	Acrobat 4.0 Scan Plug-in for Windows

Te/eEye 73m
Transmission Unit
PTA1 6-31 I PTA1 6-C1l
User Guide
s.::
Notice:
Signal Communications Limited reserves the right to make improvements to the
product described in this manual at any time and without notice.
This manual is copyrighted. All rights are reserved. This manual may not be copied,
reproduced or translated in whole or part without prior consent fiom Signal
Communications Limited-
Third party trademarks are the property of their respective holders.
Copyfight (0) 199598 Signal Communications Limited-
All rights reserved.
Version 2.6
Limits of Liability and Disclaimer of Warranty
Signal Communications Limited have taken care in preparation ofthis manual, but
makes no expressed or implied warranty of any kind and assume no responsibility for errors or
omissions. No liability is assumed for incidental or consequential damages in connection with or
arising out of the use of the information or accessories contained herein.
FCC Statement on Class B
WARNING
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determine by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
0 Reorient or relocate the receiving antenna.
0 Increase the separation between the equipment and receiver.
0 Connect the equipment into an outlet on a circuit different from that to
which the receiver is needed.
- Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the
Class B FCC limits.
Table of Contents
SECTION 1
INTRODUCTION
SECTION 2
INSTALLING TeleEye fig
What You Need
System Connections
Software Installation
Registering the Transmission Unit
Connecting re/eWin to TeIeEye f?”
Alarm Port Definition
Pin Definitions for Null Modem Cable
Transmitter Unit
SECTION 3
SPECIFICATIONS
. Model: PTA16-B1 and PTAl6-Cl
we»
.—-O\D\Dmm
11
SECTION 1
INTRODUCTION
Te/eEye 77m is an advanced Video Monitoring System. The transmission
unit is especially designed for monitoring medium sized firm, factory and
warehouse. Two models are available to suit for different applications. PTA16-
B1 is a monitoring system transmitting B/W video frames PTA16-C1 functions
as standard model for the transmission of color video.
Features
Transmits high quality videos of multiple CCTV cameras
Achieves fast video update by using an interframe image compression
Password protection on connections and settings
Built—in real time clock
Multiple alarm inputs with independent NC / NO trigger contacts
Remote control through 2 relay switches
About the Reception Software
The TeIeWin Reception Software is a Win95 application program (IBM or
compatible PC)‘ It implements the system controls as well as image decoding of
the Ts/sEye 7)” systems. The compressed data are decoded and displayed
through the PC monitor
PageS
What You Need
THO—Fl
INSTALLING TeIeEye "Pro
To install and operate the Te/eEye 7)” transmission unit, the following
items are required:
- Te/eEye he Transmission Unit
The image transmitter supports up to 16 video sources in all PAL or
NTSC format.
a CCD Camera
Color / monochrome, PAL or NTSC.
- Coaxial Cable (RG-59 recommended)
It is used to connect the video output of the CCD camera to the video
input of TeIeEye an transmission uniti
~4Mm
It is a shielded 37 ways cable.
. MM
It is used to connect the TeleEye 'Pn transmission unit to one of the
COM port of the PC.
PageG
System Connections
Up to 1621313115
Up to 16 Cameras ._.5
IBM Compatlhle
Recommended Setup Procedures:
Step 1: Plug one end at the Null Modem cable into the socket marked MODEM on the
TeIeEye 'Pu transmitter, then plug the other end to the COM port of the
computer.
Step 2: Plug one end of the BNC cable into the VIDEO OUTPUT of the CCD camera,
then plug the other end to the TeIeEye 7» 's VIDEO INPUT connector (CH1
preferred)
It more than one camera, plug the BNC cable to the Te/eEye 7)» CH: to CH16
sequentially.
Step 3: Plug one end of the alarm cable into the connector of the elan'n sensor and plug
the other end of the cable to the appropriate pins of the ALARM CONNECTOR
of the TeIeEye $14 ‘
step 4: Plug the round and of the ac, adaptor Into the socket marked POWER on the
re/eEye 'Pn transmitter. (Note: transmitter can support 9V dc. to 12V do.
supply voltage)
Step 5: Plug the ac. adapter to ac, power source and switch on the TeIeEye 7:4.
The TeIeEye 7M: ‘s LED should light up,
Page7
Software Installation
Before setting up TeIeWin, please change the video setting to 800 x 600 true
colour or 16—bit high colour in Win95’s Display Properties.
Te/eWin software contains an installation program, SETUP.EXE. Please use this
program to setup the necessary files into the hard disk of the reception unit.
Once you have completed the following installation procedure, you can run
Te/eWin directly from your hard disk
Registering the Transmission Unit
Before connecting to the transmission unit, you have to perform transmission unit
registration. This can be done under the Transmitter menu. Transmission unit
registration is required only once; all the information will be recorded in the hard
disk.
In the package, you are provided with a Registration Code and a Serial Number of
the transmission unit. You need to fill them in the Registration Message Box as
shown below. Besides, please keep them in a safe place for future reference
negmmnmn
mm a
Page8
Connecting Te/eWin to TeIeEye $0.3
Step]: Make sure you video setting of Win95 environment is 800 x 600 true colour
or 800 x 600 16-bit High Colour. To sum Te/eWin Reception Software,
click on the Start button on the taskbar, then choose Programs —>
Te/eEye ”Pm _> TeleEye ‘Pn WRS-AD-l.
StepZ: To connect to the TeIeEye ?" , click Connect under the Connection menu or
the Connect icon.
Step3: In the Connect Using box, select Direct to COM] or Direct to COM2. That
is the COM port that the null modem cable is physically connecting to.
Step4: Fill in the password in order to connect. The default password is 000000.
StepS: You may now click the connect button to make connection.
You may disconnect the connection by selecting Disconnect on the Connections menu
or clicking the Disconnect button.
You may reset the alarms by clicking Reset Alarm under the Alarm menu and fill in the
password. The default password is 000000
Alarm Port Definition
Pin1 - ALARM IN 1 Pin 19 - GND Pin 9 - ALARM IN 9 Pin 27 - GND
Pin 2 - ALARM IN 2 Pin 20 - GND Pin 10 - ALARM IN 10 Pin 28 - GND
Pin 3 ~ ALARM IN 3 Pin 21 - GND Pin 11 -AMRM IN 11 Pln 29 - GND
Pin 4 - ALARM IN 4 Pln 22 - GND Pin 12 -AI.ARM IN 12 Pin 30 - GND
Pin 5 - ALARM IN 5 Pin 23 - GND Pin 13 - ALARM IN 13 Pln 31 - GND
Pin 6 - ALARM [N 6 Pin 24 - GND Pln14 - ALARM IN 14 Pin 32 - GND
Pin 7 ~ ALARM IN 7 Pin 25 - GND Pin 15 - ALARM IN 15 Pin 33 ~ GND
Pin 8 - ALARM IN 8 Pin 26 - GND Pin 16 - ALARM IN 16 Pin 34 - GND
Pin 35 ~ GND
Pin 17 - OUTPUT SWITCH 1 A Pin 36 -0UTPUT SWITCH 1 B
Pin 18 - OUTPUT SWITCH 2 A Pin 37 - OUTPUT SWITCH 2 B
Pin Definitions of NULL MODEM CABLE
TeIeEye 7” PC PC
Pin definitions of a Transmission Unit DBZS DB9
DB-9 (female) to 2 RXD <——-————> m 2 3
DB-25 (female) or 3 TXD % RXD 3 2
DB-9 (female) to 1 CD % DTR 20 4
DB-9 (female) null 4 DTR M CD g g
5 GND % GND
modem cable 7 RTS CTS 5 8
s CTS % RTS 4 7
Page9
Transmission Unit
The panels of the Te/eEye 7” transmission unit are shown below :
PT A] 6-B1/PT AI 6-CI Front Panel
Tale-Eye P” 76
Functional Description
VIDEO IN Connectors (CHI - CHSI
- Standard BNC connectors for the video sources
- A composite video signal should be supplied to these connectors
ALARM IN Connector
- This connector is used for connecting 2 remote control switches and 8 alarm
inputs
- All alarm channels have the same priority
Communication Port
A DB—9 male connector for connecting to COM port of PC
Power Connector
A 2.1mm DC powerjack for the connection to the power supply (9V-12V DC)
Power Switch
A onloff switch of power.
Page 1 0
SECTION3
SPECIFICATIONS
MODEL
PTA 1 6-B1 / PTAIG-CI
STANDARD (P): PAUCCIR, 625 LINES, 50 FIELDS PER SECOND
(N): NTSC/EIA, 525 LINES, 60 FIELDS PER SECOND
INTERFACE I6 CHANNELS, 1.0Vpp COMPOSITE,
BNC WITH 750 TERMINATION
INPUT
SWITCH
RESOLUTION (H x V) 256 x 192 PIXELS
GRAY LEVELS 256
COLORS 16 MllLION
COIVH’RESSION SCALEABLE ADAPTIVE IMAGE COMPRESSION
16 INDEPENDENT CHANNELS, NC / N0
2 CHANNEL, DRY CONTACT
CONTACT RATING : 2A, 120V AC,
RESISTIVE LOAD : 2A, 28V DC.
TYPE RS-232C, DB-9 MALE CONNECTOR
RATE 38,400 BITS PER SECOND
FORMAT ASYNCH'RONOUS‘ 8 DATA BITS, NO PARITY, 1 STOP BIT
,8,]
FLOW CONTROL HARDWARE RTS, CTS!
DIMENSION (yv x D x H)
PROTOCOL EFFICIENT ERROR CONTROL PROTOCOL
INPUT VOLTAGE 9 - 12V DC
POWER CONSUMPTION 12W (MAX)
AMBIENT +5°c TO +40°C
TEMPERATURE (40°C TO 104°F)
RELATIVE HUMIDITY 20% TO 85%, NO CONDENSATION
330mm x 280mm x 65mm
COLOR
BLACK
WEIGHT
27 kg
Page] I

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2000:03:20 17:07:34+08:00
Create Date                     : 2000:03:20 17:07:16+08:00
Creator                         : Acrobat 4.0 Scan Plug-in for Windows
Producer                        : Acrobat 4.0 Scan Plug-in for Windows
Page Count                      : 11

EXIF Metadata provided by EXIF.tools