Signal Communications SCVT-010313 TeleEye III Video Monitoring System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	153446
Application ID	AZ6QBU3Rx8EFZLc+j5jDkA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	27.31kB (341395 bits)
Date Submitted	2001-06-06 00:00:00
Date Available	2001-06-06 00:00:00
Creation Date	2001-04-11 11:18:09
Producing Software	Acrobat 4.0 Scan Plug-in for Windows
Document Lastmod	2001-04-11 11:18:55
Document Title	User manual
Document Creator	Acrobat 4.0 Scan Plug-in for Windows

Te/eEye [11
Transmission Unit
VT3-4B
VT3-4C
VT3-4BA
VT3-4CA
User Guide
Pagel
Notice:
Signal Communications Limited reserves the right to make improvements to the
product described in this manual at any time and without notice.
This manual is copyrighted. All rights are reserved. This manual may not be copied,
reproduced or translated in whole or part without prior consent from Signal
Communications Limited.
Third party trademarks are the property of their respective holders.
Copyright (c) 1995-2000 Signal Communications Limited.
All rights reserved.
Version 2.7
Limits of Liability and Disclaimer of Warranty
Signal Communications Limited have taken care in preparation of this manual, but
makes no expressed or implied warranty of any kind and assume no responsibility for errors or
omissions. No liability is assumed for incidental or consequential damages in connection with or
arising out of the use of the information or accessories contained herein.
Page2
Table of Contents
SECTION 1
INTRODUCTION 4
INSTALLING Te/eEye 111
What You Need
System Connections
Soflware Installation
Connecting TeIéWin to Te/eEye 111
Pin Definitions of the Crossover RJ45 Cable
Transmission Unit
Functional Description
WOOOOQNG‘JI
SECTION 3
SBECIEICAIIQNS
0 Model: VT3-4B, VT3—4C, VT3-4BA and VT3-4CA 10
PageS
SECTION 1
INTRODUCTION
TeIeEye III is an advanced Video Monitoring System. The transmission unit is
especially designed for monitoring medium sized firm, factory and warehouse.
Four models are available to suit for different applications as follows.
o VT3-4B: Transmitting B/W video frames.
0 VT3—4C: Transmitting color video frames.
0 VT3-4BA: Transmitting B/W video frames with 4 alarm inputs and 1
output switch supported.
0 VT3-4CA: Transmitting color video frames with 4 alarm inputs and 1
output switch supported.
The hardware design of the four models above are the same. The alarm and switch
function provided for the VT3—4B and VTC-4C will be permanently disabled in
sofiware but the function provided for the VTC3-4BA and VTC3-4CA will be
permanently enabled in software. In short, there is only the software difference
among the models above.
Features
Transmits high quality videos of multiple CCTV cameras.
Achieves fast video update by using an interframe image compression.
Password protection on connections.
Built-in real time clock.
Multiple alarm inputs with independent NC / NO trigger contacts.
Remote control through 1 relay switch,
About the Reception Software
The fe/eWin Reception Software is a Win95/98 application program (IBM or
compatible PC). It implements the system controls as well as image decoding of
the Te/eEye III system. The compressed data are decoded and displayed
through the PC monitor.
Page4
SECTION
— 2
INSTALLING Te/eEye [I]
What You Need
To install and operate the Te/eEye [1] transmission unit, the following
items are required:
. Te/eEye III Transmission Unit
The image transmitter supports up to 4 video sources in all PAL or
NTSC format.
- QQD nggrg
Color / monochrome, PAL or NTSC.
- QQQM (RG-59 recommended)
It is used to connect the video output of the CCD camera to the video
input of Te/eEye III transmission unit
' M
It is used to connect the Te/eEye III transmission unit to Ethernet socket
of the PC.
- Adam
A d.c. 12V Adaptor.
PageS
System Connections
Up to 4 alarms
Up to 4 cameras ..
“Her-r if
R145 LAN cable
IElM Compatible
Bemmmendedfluflmedures:
Step 1:
Step 2:
Step 3:
Step 4:
step 5:
Plug one end of the RJ45 LAN cable into the socket marked Ethernet on the
Te/éye III transmitter, then plug the other end to the Ethernet socket of the
computer.
Plug one end of the HMO cable into the VIDEO OUTPUT of the CCD camera.
then plug the other end to the re/eEye 111 's VIDEO INPUT connector (CH1
preferred)
If more than one camera, plug the BNC cable sequentially to the CHZ to CH4 of
the re/eEye III.
Plug one end of the Alarm & SW cable into the 03-9 male connector of the
alarm sensor box and plug the other end of the cable to the 05-9 female
connector of the Te/eEye 111 marked Alarm & SW.
Plug the round end of the dc. adaptor Into the socket marked POWER on the
Ts/sEye III transmitter. (Note: transmitter can support 9V d.c. to 12V d.c.
supply voltage)
Plug the adaptor to a.c. power source tor switching on the re/eEye III.
The Ts/eEye III's LED should light up.
Pagcfi
Software Installation
Before setting up Te/eWin, please change the video setting to 800 x 600 true
colour or 16-bit high colour in Win95/98’s Display Properties,
Te/éNin software CD contains an installation program, SETUP. EXE. Please use
this program to setup the necessary files into the hard disk of the reception unit.
Once you have completed the following installation procedure, you can run
Te/e‘WIn directly from your hard disk.
Connecting Te/eWin to Te/eEye [II
Step 1: Make sure your video setting of Win95/98 environment is 800 x 600 true colour or 800): 600 16-
bit High Colour. To start Ts/dNin Reception Software, click on the Start button on the
taskbnr, then choose Programs -> Te/eEye 111 -> Ta/aEye IIIWRSS-AD.
Step 2: To connect to the Ts/sEye 11], click Connect under the Connection menu or the Connect button.
Step 3: In the Connect Using box, select TCP/IP and enter the IP address as 210.177.50.155. This allows
the TeldNin to communicate with the T a/aEye [11 through the N45 LAN cable.
Step 4: Fill in the password for connection. The defnnlt password is 000000.
Step 5: You may now click the connect button to make connection.
You may disconnect the connection by selecting Disconnect on the Connections menu
or clicking the Disconnect button.
You may reset the alarms by clicking Reset Alarm under the Alarm menu or with the
Reset Alarm button.
Tr lh '
If you encounter problem in connecting the TeleEye III transmitter successfully. Check
the following.
Please make sure your PC has a network card and is configmred with network settings. Go
to Control Panel->Network to enter the following network settings.
[ . IP= 210.177.50154’ \
- Subnet mask: 255.255.2550 Y
5? Lia. qu'fiffl
Page7
Pin Definitions of the crossover RJ45 CABLE
When linking Te/eEye III to PC, you need the crossover RJ45-to-RJ45 cable.
Table F-2 lists the definitions for the crossover RJ45-to-RJ45 cable.
__Termin.al A 1 Terminal B
White 1 TD+ 3 RD+ White green
orange
Orange 2 TD- 6 RD- Green
White green 3 RD+ l TD+ White orange
White blue 4 BI_H (Not used by 7 BI_2+ (Not used by White brown
lOaneT! lOBaseT)
Blue 5 BI_l- (Not used by 8 BI_2- (Not used by Brown
_ lOBaseT! lOBaseT!
Green 6 RD- 2 TD- Orange
White 7 BI_2+ (Not used by 4 BI_1+ (Not used by White blue
brown 10BaseT) lOBaseT)
Brown 8 BI_2- (Not used by S BI_l— (Not used by Blue
lOBaseT! lOBaseT!
Table F-2: Crossover RJ45-w-RJ45 cable definitions.
Transmission Unit
The panels of the re/eEye III transmission unit are shown below:
Te/eEye III 0
Front Panel
\ mm
6006 -' —- --- --- lei
(HI {H‘ illX rm ' - mw' i in. \.i\ minim I‘
i'ti:\
Rear Panel
PageS
Functional Description
11 HI - 4
Standard BNC connectors for the video sources.
A composite video signal should be supplied to these connectors.
ALARM 3; SW (Innngmx
This connector is used for connecting l remote control switches and 4
alarm inputs.
All alarm channels have the same priority.
Elem
The Ethernet socket is used for making connection to the Ethernet socket of
PC.
ALLXAnslMQllEML‘nnnm
These two connectors are used for future development.
mm
A 2.1mm DC power jack is used for the connection to the power supply (9V-
12V DC)
Page9
SECTION 3
SPECIFICATIONS
MODEL
STANDARD
INTERFACE
RESOLUTION H x
VT3—4B VT3—4C VT3-4CA
VIDEO
(P): PAL/CCIR, 625 LINES, 50 FIELDS PER SECOND
: NTSC/EIA 525 LINES 60 FIELDS PER SECOND
4 CHANNELS, 1.0Vm, COMPOSITE,
BNC WITH 750 TERMINATION
FRA .\II{ (IAI’TI IRF,
320 x 240 PIXELS
VT3 -4BA
GRAY LEVELS
COLORS
INPUT
OUTPUT
256
. 16 MILLION — 16 MILLION
SCALEABLE ADAPTIVE IMAGE COMPRESSION
,\III\R.\I
4 INDEPENDENT CHANNELS
C / NO
I CHANNEL, DRY CONTACT
CONTACT RATING: 24Vac, 2A
RESISTIVE LOAD : 24Vdc, 2A
INTERFACE
TYPE R145 CONNECTOR
RATE 10/100 Mbps
PROTOCOL TCP/IP
PO“ LR RILQLIRICM ‘NI'
9 - 12V DC
12W MAXA
If“ \'I RI )1\ \I FNT (1 ”VIII PIONS
AMBIENT +5°C TO +40°c
TEMPERATURE 40vc TO [04°F
RELATIVE HUMIDITY 20° TO 85% NO CONDENSATION
DIMENSION x D x
COLOR
WEIGHT
ML'CIIANKAI. DESIGN
254mm x 203mm x 38mm
SILVER
l.3k.
Pagel 0
1 B—QPR—Bl
FCC Statement on Class B
31 RNING
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Purl 15 ofthe FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates. uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications,
llouever, there is no guarantee that interference will not occur in a
particular installation. If lhis equipment does euuse hurmt'ul interference to
rudio or television reception. which can be determine by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
0 Increase the separation between the equipment and receiver.
0 Connect the equipment into an outlet on a circuit tlif went from that to
which the receiver is needed.
- Comull the dealer or an capcricncctl radio/TV tcchniciun for help.
Shielded cables must be used with this unit to ensure compliance with the
Class B FCC limits‘
lfi—RPR—Zem 12124 972 F.62

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:04:11 11:18:55+08:00
Create Date                     : 2001:04:11 11:18:09+08:00
Creator                         : Acrobat 4.0 Scan Plug-in for Windows
Producer                        : Acrobat 4.0 Scan Plug-in for Windows
Page Count                      : 11

EXIF Metadata provided by EXIF.tools