Silex Technology SXPCEACDB SX-PCEAC-DB User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3071223
Application ID	XPdpPNmPrmGRsmNlmyOOpw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	81.91kB (1023889 bits)
Date Submitted	2016-07-21 00:00:00
Date Available	2016-07-25 00:00:00
Creation Date	2016-04-05 22:50:39
Producing Software	iTextSharp™ 5.5.7 ©2000-2015 iText Group NV (AGPL-version); modified using iTextSharp™ 5.5.7 ©2000-2015 iText Group NV (AGPL-version)
Document Lastmod	2016-04-06 12:05:50
Document Title	Users Manual
Document Creator	CubePDF

Title:
PCI Express Half mini card WLAN module
SX-PCEAC-DB
Drawing Type :
User’s manual
Date :
March 18, 2016
© silex technology, Inc.
(1/18)
CONFIDENTIAL
Revision History
Rev.
Description
The first edition.
© silex technology, Inc.
Date
Prepared
Checked
Approved
Mar.18,16
K.Yoshikawa
Y.Shibuya
T.Kometani
Date：March 18, 2016
(2/18)
CONFIDENTIAL
Table of Contents
1.
Introduction ............................................................................. 4
2.
Overview ................................................................................. 4
3.
Hardware system block diagram ............................................................ 5
4.
Board specifications ..................................................................... 6
4.1.
General specifications ......................................................... 6
4.2.
Environmental specifications ................................................... 6
4.3.
Electrical specifications ...................................................... 7
4.4. Wireless LAN general specifications .............................................. 8
5.
Connector interface specifications....................................................... 10
5.1.
PCI Express Mini Card edge pin assignments .................................... 10
6.
Mechanical Specifications ............................................................... 12
7.
System requirements and quick start guide................................................ 13
8.
Notifications ........................................................................... 15
© silex technology, Inc.
Date：March 18, 2016
(3/18)
CONFIDENTIAL
1. Introduction
This document describes about hardware specifications of “SX-PCEAC-DB”.
2. Overview
SX-PCEAC-DB is the radio module which supports Dual Band IEEE802.11ac/a/b/g/n and PCI express
1.1. This module complies with EU RoHS Directive 2011/65/EC(Lead Free). This module is made up
of an Chipset QCA9880-BR4A (Qualcomm Atheros) which contains a MAC/BBP, 2.4GHz RF front end
circuits and a 5GHz RF front end module AWL9581(Anadigics). Also this module supports high speed
3x3 SU-MIMO and 80MHz bandwidth.
Features
❑ IEEE 802.11ac/a/b/g/n conformity (2.4GHz & 5GHz)
❑ Supports the 3 streams 3 x 3 SU-MIMO system and 80MHz band width for 5GHz.
(Throughput up to 1300Mbps)
❑ Data rates of 1 - 54 Mbps for 802.11b/g, 6 - 54 Mbps for 802.11a, MCS0-7 for 802.11n and
MCS0-9 for 802.11ac.
❑ Supports IEEE802.11e, IEEE 802.11h and IEEE 802.11i.
❑ Supports PCI express 1.1 as the host IF of wireless LAN
* Not supported MU-MIMO and 160MHz bandwidth.
© silex technology, Inc.
Date：March 18, 2016
(4/18)
CONFIDENTIAL
3. Hardware system block diagram
①
②
③
④
⑤
QCA9880
Low pass filter
Band pass filter
Single pole double throw switch
Fron end module
⑥
⑦
⑧
⑨
⑩
Single pole double throw switch
Co-axial connector NOTE1
Crystal driver
Voltage stabilizer NOTE2
Switching regulator NOTE2
Wireless Lan base band IC. Generates base band signal.
Cuts off signal above 2.5GHz.
Cuts off signal under 5GHz and above 6GHz.
Switches Tx and Rx of 2.4GHz.
Integrates a 5GHz power amplifier, a 5GHz low noise and
Tx/Rx select swtich.
Switches 2.4GHz and 5GHz.
Antenna port. MHF4 type.
Generates 40MHz system clock.
Stabilize +3.3VDC for RF.
Coverts +3.3VDC to +1.2VDC.
NOTE1
Any signals of 1 stream data, 2 stream data and 3 stream data is output from three antennas.
NOTE2
Any voltage source for RF parts are generated/stabilized on the module.(RF +3.3V, RF +1.2V)
RF performance shown in the product spec is not affected by any behaviors of external +3.3V supply.
© silex technology, Inc.
Date：March 18, 2016
(5/18)
CONFIDENTIAL
4.
Board specifications
4.1. General specifications
Items
Specifications
Units
Connector Type
PCI express mini card edge
－
Antenna connectors
MHF4 Alternative connector x 3
pcs
Device Interfaces
PCI Express Mini Card v1.2
－
RF Interface
IEEE802.11ac/a/b/g/n
MTBF
90,000
Remarks
Signal definitions : PCI
Express v1.1
Min.
4.2. Environmental specifications
Items
Specifications
Units
Remarks
Min.
Typ.
Max.
-20
－
+60
℃
Case temperature
After assembled with powered
Operating humidity
20
－
80
%RH
Non condensing
After assembled with powered
Assembled storage
temperature
-20
－
+85
℃
After assembled with no-powered
Storage humidity
20
－
85
%RH
Non condensing
After assembled with no-powered
Operating Temperature
© silex technology, Inc.
Date：March 18, 2016
(6/18)
CONFIDENTIAL
4.3. Electrical specifications
Absolute Maximum Ratings (Ta=+25℃)
Specifications
Items
Main Power supply voltage (VDD)
Min.
Typ.
Max.
-0.3
－
+3.6
Units
Remarks
Recommended Operating Conditions (Ta=+25℃)
Specifications
Items
Main Power supply voltage (VDD)
Units
Min.
Typ.
Max.
+3.135
+3.3
+3.465
Remarks
Digital logic signal level (Ta=+25℃)
Items
Parameters
Specifications
Sink current
Min.
Typ.
Max.
Units
VIH
Input High Voltage
0.7 x VDD
－
－
VIL
Input Low Voltage
－
－
0.3 x VDD
VOH
Output High Voltage
0.9 x VDD
－
－
VOL
Output Low Voltage
－
－
0.1 x VDD
Remarks
※All voltage source for the analog RF power supply is internally regulated in the module, and RF
performance described in this document is not affected by any variation for external power source.
© silex technology, Inc.
Date：March 18, 2016
(7/18)
CONFIDENTIAL
4.4.
Wireless LAN general specifications
Items
Specifications
Units
Chipset
QCA9880-BR4A (Qualcomm Atheros)
－
Country code
US
－
Center frequency
11a/11nHT20/11acVHT20
5180 - 5825
11n HT40/11ac VHT40
5190 - 5795
11ac VHT80
5210 - 5775
11b
2412 - 2462
MHz
11g
2412 - 2462
MHz
11ng HT20
2412 - 2462
MHz
11ng HT40
2422 - 2452
MHz
11a/11nHT20/11acVHT20
20
11nHT40/11acVHT40
40
11acVHT80
80
11b/11g/11ngHT20/11ngHT40
Channel spacing
Link rate
Modulation type
engine
US:2412–2462MHz
MHz
1,2,5.5L,5.5S,11L,11S
Mbps
11a/g
6,9,12,18,24,36,48,54
Mbps
11ng/na/ac 1-3 Stream
MCS0,1,2,3,4,5,6,7,8,9
－
11b
DSSS(CCK,DQPSK,DBPSK)
11na/11ng/11ac
Hardware encryption
US:W52/W53/W56/W58
MHz
11b
11a/11g
WiFi
© silex technology, Inc.
OFDM
(64QAM,16QAM,QPSK,BPSK)
OFDM
(256QAM,64QAM,16QAM,QPSK,BPSK)
Remarks
－
RC4(64-128bit)
－
AES(128-256bit)
－
Date：March 18, 2016
(8/18)
CONFIDENTIAL
Usable channel list
11b
Ch.1, Ch.2, Ch.3, Ch.4, Ch.5, Ch.6, Ch.7, Ch.8, Ch.9, Ch.10, Ch.11
11g
Ch.1, Ch.2, Ch.3, Ch.4, Ch.5, Ch.6, Ch.7, Ch.8, Ch.9, Ch.10, Ch.11
11ng HT20
Ch.1, Ch.2, Ch.3, Ch.4, Ch.5, Ch.6, Ch.7, Ch.8, Ch.9, Ch.10, Ch.11
11ng HT40
Ch.3, Ch.4, Ch.5, Ch.6, Ch.7, Ch.8, Ch.9
11a
Ch.36, Ch.40, Ch.44, Ch.48, Ch.52, Ch.56, Ch.60, Ch.64
Ch.100, Ch.104, Ch.108, Ch.112, Ch.116, Ch.120, Ch.124, Ch.128, Ch.132, Ch.136, Ch140
Ch.145, Ch.149, Ch.153, Ch.157, Ch.161, Ch.165
11n HT20
Ch.36, Ch.40, Ch.44, Ch.48, Ch.52, Ch.56, Ch.60, Ch.64
11ac VHT20
Ch.100, Ch.104, Ch.108, Ch.112, Ch.116, Ch.120, Ch.124, Ch.128, Ch.132, Ch.136, Ch140
Ch.145, Ch.149, Ch.153, Ch.157, Ch.161, Ch.165
11n HT40
Ch.38, Ch.46, Ch.54, Ch.62
11ac VHT40
Ch.102, Ch.110, Ch.118, Ch.126, Ch.134
Ch.151, Ch.159
11ac VHT80
Ch.42, Ch.58
Ch.106, Ch.122
Ch.155
・Above region code relating channel list is programmed in the module by module manufacturer
(Silex).
・Since programmed region code and channel list is binary data and user cannot know the structure
of program, any customers cannot change usable channels.
Operation theory
Client mode (Station)
Operation frequencies
2.4GHz band
W52
W53
11b/g/n
11a/an/ac
11a/an/ac
W56
11a/an/ac
W58
11a/an/ac
2412-2462MHz
5180-5240MHz
5260-5320MHz
5500-5700MHz
※IC:5600-5650MHz disable
5745-5825MHz
Active/Passive
ad-hoc mode
Active scan
Active scan
Passive scan
No
No
No
Passive scan
No
Active scan
No
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down through the MAC,
through the digital and analog baseband, and finally to the RF chip. Several special packets
are initiated by the MAC. These are the only ways the digital baseband portion will turn on the
RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter
will be on only while one of the aforementioned packets is being transmitted. In other words,
this device automatically discontinue transmission in case of either absence of information to
transmit or operational failure.
© silex technology, Inc.
Date：March 18, 2016
(9/18)
CONFIDENTIAL
5. Connector interface specifications
5.1. PCI Express Mini Card edge pin assignments
Pin
Numbers
Pin Names
Types
RESERVED
OD
+3.3Vaux
PWR
RESERVED
IO
GND
GND
RESERVED
IO
RESERVED
NC
RESERVED
OD
RESERVED
NC
GND
GND
10
RESERVED
NC
11
REFCLK-
IA
12
RESERVED
NC
13
REFCLK+
IA
14
RESERVED
NC
15
GND
GND
16
RESERVED
NC
Descriptions
WAKE_L
Connected to GPIO.
Connected to GPIO.
CLKREQ_L
PCI Express differential reference clock (100MHz)
PCI Express differential reference clock (100MHz)
Mechanical key
17
RESERVED
NC
18
GND
GND
19
RESERVED
NC
20
RESERVED
IO
21
GND
GND
22
PERST_L
IL
Express reset. Internal weak pull-down
23
PERn0
OA
Module : Differential data transmit
24
+3.3Vaux
PWR
25
PERp0
OA
© silex technology, Inc.
Disable wireless module. On board Pull-up(10kohm)
Module : Differential data transmit
Date：March 18, 2016
(10/18)
CONFIDENTIAL
NC
IO
IA
OA
OD
IL
PWR
GND
Pin
Numbers
Pin Names
Types
26
GND
GND
27
GND
GND
28
RESERVED
NC
29
GND
GND
30
RESERVED
NC
31
PETn0
IA
32
RESERVED
NC
33
PETp0
IA
34
GND
GND
35
GND
GND
36
RESERVED
NC
37
RESERVED
NC
38
RESERVED
NC
39
RESERVED
NC
40
GND
GND
41
RESERVED
NC
42
RESERVED
NC
43
RESERVED
GND
Connected to GND
44
RESERVED
IO
Connected to GPIO.
45
RESERVED
IO
Connected to GPIO
46
RESERVED
NC
47
RESERVED
IO
48
RESERVED
NC
49
RESERVED
NC
50
GND
GND
51
RESERVED
NC
52
+3.3V
PWR
Descriptions
Module : Differential data receive
Module : Differential data receive
Connected to pin 41 internally
Connected to pin 39 internally
Connected to GPIO.
No Connection.
Digital bidirectional pin.
Analog input signal.
Analog output signal.
Digital output signal with open drain.
Input signal with weak internal pull-down.
Power signal.
Ground signal.
© silex technology, Inc.
Date：March 18, 2016
(11/18)
CONFIDENTIAL
6.
Mechanical Specifications
4.00
2.10
1.00
TOP View
SIDE View
BOTTOM View
*Solder thickness=0.1mm
+/-0.15mm
0.15mm
Thickness +/-0.25mm
+/ 0.25mm
+/ 0.15 mm, unless otherwise specified.
All dimension tolerances are +/-0.15
© silex technology, Inc.
Date：
：March
March 18, 2016
(12/18
18)
CONFIDENTIAL
7. System requirements and quick start guide
1) System requirements
Prepare the host CPU board whose spec requirements are shown below.
System pecifications
Items
Descriptions
MCU (CPU)
ARM based 1.0GHz or greater SoC from any companies.
Eg. Freescale i.MX6SX – 1200MHz
Memory size
ROM : 512MB, RAM : 1GB or greater
OS
Linux any kernel distribution
Host interface
PCI Express 1.1
2) Install the driver which is provided by Silex to the CPU board.
Any other 3rd party’s software shall be rejected due to Subsystem ID mismatch.
3) Install the SX-PCEAC-DB board to the CPU board.
SX-PCEAC-DB
Board
PCI Express
mini Card
connector
CPU board
© silex technology, Inc.
Date：March 18, 2016
(13/18)
CONFIDENTIAL
System block diagram
4) Antenna location
Attach the antenas to the co-axial connectors on the SX-PCEAC-DB board. This product doesn’
t include the CPU board and the plastic case. The figure below is an assumed example of embedded
system. Both the baseboard and the case does not affect to RF performance including Antenna
performance as long as distance between each antenna is farther than 30mm. Installater must keep
this distance when installing this module.
© silex technology, Inc.
Date：March 18, 2016
(14/18)
CONFIDENTIAL
8.
Notifications
FCCID ：N6C-SXPCEACDB
IC
：4908A-SXPCEACDB
Regulatory notice
Channel Selection
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection
of other channels is not possible.
Fcc Rules Part 15
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s
authority to operate the equipment.
FCC Rules, Part 15 §15.19(a)(3) / IC RSS Gen §8.4
Below sentences must be indicated on the final product which contains this module inside.
This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs.
Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil
ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
FCC Rules Part 15 Subpart C §15.247 and Subpart E / IC RSS-102 §2.6
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC
radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping
the radiator at least 20cm or more away from person’s body.
Cet équipement est conforme aux limites d ’ exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes
directrices d'exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’
IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre
le radiateur et le corps humain.
© silex technology, Inc.
Date：March 18, 2016
(15/18)
CONFIDENTIAL
FCC Rules Part 15 Subpart E §15.407(c)
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down through the MAC,
through the digital and analog baseband, and finally to the RF chip. Several special packets
are initiated by the MAC. These are the only ways the digital baseband portion will turn on the
RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter
will be on only while one of the aforementioned packets is being transmitted. In other words,
this device automatically discontinue transmission in case of either absence of information to
transmit or operational failure.
FCC Rules Part 15 Subpart E §15.407(g)
Frequency Tolerance: +/-20 ppm
FCC Rules Part 15 Subpart C §15.247(g) / Subpart E
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
RSS-Gen §8.3
This radio transmitter 4908A-SXPCEACDB has been approved by Industry Canada to operate with
the antenna types listed below with the maximum permissible gain and required antenna impedance
for each antenna type indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le numéro IC du présent émetteur radio 4908A-SXPCEACDB a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal
et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette
liste, ou dont le gain est supérieur au gain maximal indiqué pour ce type, sont strictement
interdits pour l'exploitation avec cet appareil.
Certified antenna list
Part number
Vendor
146153
H2B1PC1A1C (AA258)
H2B1PD1A1C (AA222)
Molex
Unictron
Unictron
© silex technology, Inc.
2.4GHz
+3.25
+2.90
+2.80
W52
+5.00
+4.40
+4.20
Antenna Gain
W53
W56
+5.00
+5.00
+4.40
+4.40
+4.20
+4.20
W58
+5.00
+4.40
+4.20
Units
dBi
dBi
dBi
Date：March 18, 2016
(16/18)
CONFIDENTIAL
RSS-247 Issue 1 May 2015
Radio Standards Specification RSS-247, Issue 1, Digital Transmission Systems (DTSs), Frequency
Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices, is a new standard
to replace annexes 8 and 9 of RSS-210, Issue 8, Licence-exempt Radio Apparatus (All Frequency
Bands): Category I Equipment.
At the date of publication of this standard, devices covered under the scope of this document
will no longer be certified under RSS-210, Issue 8.
Le Cahier des normes radioélectriques 247, 1re édition, Les systèmes de transmission numérique
(STN), les systèmes à sauts de fréquence (SSF) et les dispositifs de réseaux locaux exempts de
licence (RL-EL), remplace les annexes 8 et 9 du CNR-210, 8e édition, Appareils radio exempts
de licence (pour toutes les bandes de fréquences) : matériel de catégorie I.
À la date de publication de la présente norme, les dispositifs visés par ce document ne seront
plus certifiés conformément au CNR-210, 8e édition.
Frequency Band 5150 – 5250 MHz
LE-LAN devices are restricted to indoor operation only in the band 5150-5250 MHz.
Les dispositifs LAN-EL sont restreints à une utilisation à l'intérieur, dans la bande
5150-5250MHz.
High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350
MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN
devices.
Les radars de haute puissance sont désignés comme utilisateurs principaux (c ’ est-à dire
utilisateurs prioritaires) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et que ces radars
peuvent provoquer du brouillage et/ou des dommages aux dispositifs LAN-EL.
© silex technology, Inc.
Date：March 18, 2016
(17/18)
CONFIDENTIAL
WARNING：
The FCC / The Industry Canadaregulations provide that changes or modifications not expressly
approved by the party responsible for compliance could void the user’sauthority to operate the
equipment.
Manual and Product Labeling information To The End User
The end user manual shall include all required regulatory information/warning as show in this
manual.And when this module is installed in the host product, you must include a “Contain FCC
ID : N6C-SXPCEACDB”and a “Contain IC: 4908A- SXPCEACDB” in the label of the host product.
This module is designed for embedded purpose into the general electric devices, and is not
designed for high reliability demands like aircraft instruments, nuclear control instruments,
high reliability medical instruments, high reliability security instruments or any other devices
required extremely high reliability and quality.
• As this module communicates by radio wave, it is strongly recommended to use some security
system to prevent unexpected information leakage to others.
• This module is a radio module for embedded purpose. Please understand functions and features
of this module, and evaluate as the final product which has this module embedded. Also, as
evaluation of EMC conformity of this module has not been performed, EMC conformity evaluation
and application must be performed with the final product which this module is embedded.
• This module will effect to some other device or be affected by the some other device using
the same frequency band.Please investigate the environment to use this module beforehand.
• Disassembling or modifying the radio module leads to punishment based on radio law.
• This module is the embedded module that has the exposed connectors or some devices.Please be
careful for electro static, condensing, and other dusts.
• “The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module.”
IMPORTANT NOTE: In the event that these conditions cannot be met (for example co-location with
another transmitter), then the FCC / IC authorization is no longer considered valid and the
FCC / IC ID cannot be used on the final product. In these circumstances, the OEM integrator
will be responsible for reevaluating the end product (including the transmitter) and obtaining
a separate FCC / IC authorization. As long as a condition above is met, further transmitter
test will not be required. However, the OEM integrator is still responsible for testing their
end product for any additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.
© silex technology, Inc.
Date：March 18, 2016
(18/18)
CONFIDENTIAL

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : 
Create Date                     : 2016:04:05 22:50:39+09:00
Modify Date                     : 2016:04:06 12:05:50+08:00
Subject                         : 
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : 
Description                     : 
Title                           : 
Creator Tool                    : CubePDF
Metadata Date                   : 2016:04:06 12:05:50+08:00
Keywords                        : 
Producer                        : iTextSharp™ 5.5.7 ©2000-2015 iText Group NV (AGPL-version); modified using iTextSharp™ 5.5.7 ©2000-2015 iText Group NV (AGPL-version)
Document ID                     : uuid:b2b2bdf3-7c6d-4001-a532-f2f7967b151b
Instance ID                     : uuid:27568292-ed7d-4a42-a2b7-4fe513b34eb2
Page Count                      : 18

EXIF Metadata provided by EXIF.tools