Silex Technology SXPCEAN Wireless LAN PCI Express Mini Card Module User Manual

Silex Technology, Inc. Wireless LAN PCI Express Mini Card Module Users Manual

Contents

05 Users Manual_Rev.pdf

(1/13) CONFIDENTIAL © silex technology, Inc. Wireless LAN PCI Express Mini Card Module SX-PCEAN User’s Manual
SX-PCEAN User’s Manual Date：July 23, 2012 (2/13) CONFIDENTIAL © silex technology, Inc. Table of Contents 1．Introduction ........................................................................................................................................................ 3 2．Overview ............................................................................................................................................................. 3 3．Block diagram .................................................................................................................................................... 4 4．Specifications .................................................................................................................................................... 5 4-1．General specifications .................................................................................................................. 5 4-2．Environmental specifications ...................................................................................................... 5 4-3．Electrical specifications ............................................................................................................... 5 4-4．Radio configuration and general specifications ......................................................................... 6 5．PCI Express Mini Card Interface Specifications .......................................................................................... 7 5-1．PCI Express Mini Card edge pin assignments .......................................................................... 7 6．Mechanical Specifications ............................................................................................................................... 9 7. System Requirements .................................................................................................................................. 10 8. Notifications .................................................................................................................................................. 11
SX-PCEAN User’s Manual Date：July 23, 2012 (3/13) CONFIDENTIAL © silex technology, Inc. 1．Introduction This document describes about “SX-PCEAN”. 2．Overview SX-PCEAN+ is Dual Band IEEE802.11abgn PCI Express Half Mini Card interface radio module. This module complies with EU RoHS Directive 2011/65/EC(Lead Free) and China RoHS with exemptions. This module has an MAC/BBP Chipset AR9280 (Atheros) and two RF front end modules which contains PA, LNA and RF switch internally. Also this module supports high speed two stream MIMO technology and 40MHz band width mode. Features: -IEEE 802.11a/b/g/n conformity (2.4GHz & 5GHz) -Two stream 2 x 2 MIMO technology and 40MHz band width mode. (Throughput up to 300Mbps) - Data rates of 1 - 54 Mbps for 802.11b/g, 6 - 54 Mbps for 802.11a and MCS0-15 for 802.11n. - Support IEEE802.11e, IEEE 802.11h and IEEE 802.11i. - Support PCI Express Mini Card 1.2 (Signal definitions : PCI Express 1.1) - Support “Short Guard Interval” mode. - Support Tx/Rx selection Tx/Rx diversity at IEEE802.11a/b/g mode.
SX-PCEAN User’s Manual Date：July 23, 2012 (4/13) CONFIDENTIAL © silex technology, Inc. 3．Block diagram ANT Connectors :U.FL Alternative
SX-PCEAN User’s Manual Date：July 23, 2012 (5/13) CONFIDENTIAL © silex technology, Inc. 4．Specifications 4-1．General specifications Item Specification Unit Note Connector Type PCI Express Mini Card edge － Antenna connectors U.FL Alternative connector x 2 － Device Interfaces PCI Express Mini Card v1.2 － Signal definitions : PCI Express v1.1 IEEE802.11a/b/g/n/e/h/i － Weight 4.5 +/- 1.0 g Dimensions 30.0 x 26.8 x 4.5 mm 4-2．Environmental specifications Item Specification Unit Note Storage temperature -20 to +85 ℃ Storage humidity 10 to 85 %RH Non condensing Operating Temperature 0 to +60 ℃ Ambient Operating humidity 20 to 80 %RH Non condensing Maximum temperature change 20 ℃/H 4-3．Electrical specifications Item Specification Unit Note Power supply voltage Min. Typ. Max. -0.3 - 4.0 V Absolute Maximum Ratings 2.97 3.30 3.63 V Recommended Operating Conditions
SX-PCEAN User’s Manual Date：July 23, 2012 (6/13) CONFIDENTIAL © silex technology, Inc. 4-4．Radio configuration and general specifications Item Specification Unit Note Chipset AR9280 (Atheros) － 11a 5180 – 5320 / 5745 – 5825 MHz Center frequency 11na HT20 5180 – 5320 / 5745 – 5825 11na HT40 5190 – 5310 / 5755 – 5795 11b 2412 – 2462 MHz 11g 2412 – 2462 11ng HT20 2412 – 2462 11ng HT40 2422 – 2452 MHz 11a/11naHT20 20 MHz Channel Spacing 11b/11g/11ng HT20/11ng HT40 5 11na HT40 40 11b 1, 2, 5.5L, 5.5S, 11L, 11S Mbps Rate 11a/g 6, 9, 12, 18, 24, 36, 48, 54 11na/11ng 1Stream MCS0, 1, 2, 3, 4, 5, 6, 7 － Scheme code 11na/11ng 2Stream MCS8, 9, 10, 11, 12, 13, 14, 15 － 11a/11na OFDM(64QAM,16QAM,QPSK,BPSK) Modulation type 11b DSSS(CCK,DQPSK,DBPSK) － 11g/11ng DSSS-OFDM (64QAM,16QAM,QPSK,BPSK)
SX-PCEAN User’s Manual Date：July 23, 2012 (7/13) CONFIDENTIAL © silex technology, Inc. 5．PCI Express Mini Card Interface Specifications 5-1．PCI Express Mini Card edge pin assignments Pin Number Pin Name Type Description 1 WAKE# OD PCI Express request to service function - initiated wake event, open drain 2 +3.3Vaux PWR 3 RESERVED OD Connected to GPIO. WLAN active signal 4 GND GND 5 RESERVED OD Connected to GPIO. Bluetooth active signal 6 +1.5V NC 7 CLKREQ# OD PCI Express reference clock request, open drain 8 UIM_PWR NC 9 GND GND 10 UIM_DATA NC 11 REFCLK- IA PCI Express differential reference clock (100MHz) 12 UIM CLK NC 13 REFCLK+ IA PCI Express differential reference clock (100MHz) 14 UIM_RESET NC 15 GND GND 16 UIM_VPP NC Mechanical key 17 RESERVED (UIM_C8) NC 18 GND GND 19 RESERVED (UIM_C4) NC 20 RESERVED ID Connected to GPIO. Disable wireless module. Pull-up(10kohm) 21 GND GND 22 PRESET# IH PCI Express reset. Weak pull-up 23 PERn0 OA Module : Differential data transmit 24 +3.3Vaux PWR 25 PERp0 OA Module : Differential data transmit
SX-PCEAN User’s Manual Date：July 23, 2012 (8/13) CONFIDENTIAL © silex technology, Inc. Pin Number Pin Name Type Description 26 GND GND 27 GND GND 28 +1.5V NC 29 GND GND 30 SMB_CLK NC 31 PETn0 IA Module : Differential data receive 32 SMB_DATA NC 33 PETp0 IA Module : Differential data receive 34 GND GND 35 GND GND 36 USB_D- NC 37 RESERVED NC 38 USB_D+ NC 39 RESERVED NC : Connected to pin 41 internally 40 GND GND 41 RESERVED NC : Connected to pin 39 internally 42 LED_WWAN# NC 43 RESERVED GND Connected to GND 44 LED_WLAN# OD LED control for WLAN module. Pull-up high (10kohm) 45 RESERVED NC 46 LED_WPAN# NC 47 RESERVED NC 48 +1.5V NC 49 RESERVED NC 50 GND GND 51 RESERVED NC 52 +3.3Vaux PWR NC : No connection IA : Analog input ID : Digital input IH : Digital output with weak pull-up OA : Analog output OD : Digital output PWR : Power GND : Ground
SX-PCEAN User’s Manual Date：July 23, 2012 (9/13) CONFIDENTIAL © silex technology, Inc. 6．Mechanical Specifications Thickness = 4.5mm Board thickness = 1.0mm
SX-PCEAN User’s Manual Date：July 23, 2012 (10/13) CONFIDENTIAL © silex technology, Inc. 7. System Requirements The system requirements below or compatible system are necessary to stably use this module. Recommended system : Items Descriptions Notes OS Linux/Windows/other CPU 1GHz Memory 1GByte Peripheral IF PCI Express x1 Slot It uses Driver and a utility of Atheros Communications. （Atheros client utility） It completes installation according to setup Wizard
SX-PCEAN User’s Manual Date：July 23, 2012 (11/13) CONFIDENTIAL © silex technology, Inc. 8. Notifications FCC ID：N6C-SXPCEAN IC ：4908B-SXPCEAN NOTICE Federal Communication Interference Statement (United States only) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Re-orient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. Canadian Depertment of Communications Industry Canada Notice (Canada only) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC Rules, Part 15./ Industry Canadian This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference, including interference that may cause undesired operation of this device. Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : • l'appareil ne doit pas produire de brouillage, et • l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
SX-PCEAN User’s Manual Date：July 23, 2012 (12/13) CONFIDENTIAL © silex technology, Inc. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition dans le Supplément C à OET65 et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles). Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This radio transmitter 4908B-SXPCEAN has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio 4908B-SXPCEAN a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is going to be operated in 5.15~5.35GHz frequency range, it is restricted in indoor environment only. Antenna information: Sleeve Antenna: 1.5dBi (2.4GHz), 2.1dBi (5GHz) Frequency Tolerance：+/-20ppm WARNING： The FCC / The Industry Canada regulations provide that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Manual and Product Labeling information To The End User The end user manual shall include all required regulatory information/warning as show in this manual. And when this module is installed in the host product, you must include a "Contain FCC ID : N6C-SXPCEAN" and a “Contain IC: 4908B-SXPCEAN” in the label of the host product.
SX-PCEAN User’s Manual Date：July 23, 2012 (13/13) CONFIDENTIAL © silex technology, Inc. This module is designed for embedded purpose into the general electric devices, and is not designed for high reliability demands like aircraft instruments, nuclear control instruments, high reliability medical instruments(Class III, IV), high reliability security instruments or any other devices required extremely high reliability and quality. In the case embedded into the medical instrument, please ask to silex despite the medical class. ･ As this module communicates by radio wave, it is strongly recommended to use some security system to prevent unexpected information leakage to others. ･ This module is a radio module for embedded purpose. Please understand functions and features of this module, and evaluate as the final product which has this module embedded. Also, as evaluation of EMC conformity of this module has not been performed, EMC conformity evaluation and application must be performed with the final product which this module is embedded. ･ This module will effect to some other device or be affected by the some other device using the same frequency band. Please investigate the environment to use this module beforehand. ･ Disassembling or modifying the radio module leads to punishment based on radio law. ･ This module is the embedded module that has the exposed connectors or some devices. Please be careful for electro static, condensing, and other dusts.

Navigation menu