Silicon Laboratories Finland 11 Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module User Manual BGM11Sx User Guide Certification Notes ACB

Download:
Mirror Download [FCC.gov]
Document ID	3425246
Application ID	uMX4C33pe/wjX2uIqcnR/Q==
Document Description	BGM11Sx User Guide Certification Notes - ACB
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.63kB (420322 bits)
Date Submitted	2017-06-14 00:00:00
Date Available	2017-06-14 00:00:00
Creation Date	2017-04-07 15:05:48
Producing Software	Microsoft® Word 2016
Document Lastmod	2017-04-07 15:05:48
Document Title	BGM11Sx User Guide Certification Notes - ACB
Document Creator	Microsoft® Word 2016
Document Author:	Lauren Lehman

INSTALLATION GUIDE
Figure 1: Layout guide for BGM121A/BGM123A
Figure 2: Layout guide for BGM121N/BGM123N
Alberga Business Park, Bertel Jungin aukio 3
FI-02600 Espoo, Finland
Phone: +358 9 435 5060
www.silabs.com
Japan
BGM11S1A / BGM11S2A is certified in Japan with certification number TBD.
IMPORTANT:
The module does is not labeled with Japan certification mark and ID because of the small
physical size. Manufacturer who integrates a radio module in their host equipment must
place the certification mark and certification number on the outside of the host equipment.
TBA
Figure 3: GITEKI mark and ID
The certification mark and certification number must be placed close to the text in the
Japanese language which is provided below.
当該機器には電波法に基づく、技術基準適合証明等を受けた特定無線設備を装着している。
Figure 4:GITEKI mark
Page 2 of 5
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by Silicon Labs could void the user’s authority to
operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter meets both portable and mobile limits as
demonstrated in the RF Exposure Analysis and SAR test report. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter except in
accordance with FCC multi-transmitter product procedures.
OEM Responsibilities to comply with FCC Regulations
The transmitter module must not be co-located or operating in conjunction with any other
antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
OEM integrator is responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
IMPORTANT NOTE: In the event that the above conditions cannot be met (for certain
configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The BGM11S1A / BGM11S2A Module is labeled with its own FCC ID. If the FCC ID is not
visible when the module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed module. In
that case, the final end product must be labeled in a visible area with the following:
“Contains Transmitter Module FCC ID: QOQ11”
or
“Contains FCC ID: QOQ11
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module or change RF related parameters in the user
manual of the end product.
Page 3 of 5
ISEDC
This radio transmitter (IC: 5123A-11) has been approved by Industry Canada to operate with
the embedded chip antenna. Other antenna types are strictly prohibited for use with this
device.
This device complies with Industry Canada’s license-exempt RSS standards. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device
RF Exposure Statement
BGM11S1A/BGM11S2A modules has been tested for worst case RF exposure. As
demonstrated in the SAR test report, BGM121A/BGM123A can be mounted in touch with
human body without further SAR evaluation.
OEM Responsibilities to comply with IC Regulations
The transmitter module must not be co-located or operating in conjunction with any other
antenna or transmitter.
OEM integrator is responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain
configurations or co-location with another transmitter), then the IC authorization is no longer
considered valid and the IC ID cannot be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate IC authorization
End Product Labeling
The BGM11S1A / BGM11S2A Module is labeled with its own IC ID. If the IC ID is not visible
when the module is installed inside another device, then the outside of the device into which
the module is installed must also display a label referring to the enclosed module. In that
case, the final end product must be labeled in a visible area with the following:
“Contains Transmitter Module IC: 5123A-11”
or
“Contains IC: 5123A-11”
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module or change RF related parameters in the user
manual of the end product
Page 4 of 5
CE
The Declaration of Conformity may be consulted at www.silabs.com.
Please note that every application using the BGM11S1A or BGM11S2A will need to perform
the radio EMC tests on the end product according to EN 301 489-17.
The conduced test results can be inherited from the modules test report to the test report of
the end product using BGM11S1A or BGM11S2A. EN300328 radiated spurious emission
test must be repeated with the end product assembly. Test documentation and software for
the EN 300 328 radiated spurious emissions testing can be requested from the Silicon Labs
support.
Page 5 of 5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 5
Language                        : fi-FI
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Creator                         : Lauren Lehman
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2017:04:07 15:05:48+03:00
Modify Date                     : 2017:04:07 15:05:48+03:00
Document ID                     : uuid:063A9144-AEDD-4251-8D57-24853E87D6BB
Instance ID                     : uuid:063A9144-AEDD-4251-8D57-24853E87D6BB
Author                          : Lauren Lehman

EXIF Metadata provided by EXIF.tools