Silicon Laboratories Finland BLE121LR BLE121LR long range Bluetooth Smart module User Manual Product Data Sheet

Silicon Laboratories Finland Oy BLE121LR long range Bluetooth Smart module Product Data Sheet

UserManual.wiki >

Silicon Laboratories Finland >

BLE121LR User Manual

User Manual

BLE121LR DATA SHEET Sunday, 08 June 2014 Version 1.12

Bluegiga Technologies Oy Copyright © 2000-2014 Bluegiga Technologies All rights reserved. Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual. Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. Bluegiga’s products are not authorized for use as critical components in life support devices or systems. The WRAP is a registered trademark of Bluegiga Technologies The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners.

Bluegiga Technologies Oy VERSION HISTORY Version Comment 1.1 First release 1.11 Standard gain mode option for the receiver added. Figure 22 corrected 1.12 FCC and IC info added

Bluegiga Technologies Oy TABLE OF CONTENTS 1 BLE121LR Product numbering ......................................................................................................................6 2 Pinout and Terminal Description ...................................................................................................................7 2.1 I/O Ports .............................................................................................................................................. 10 2.1.1 I/O Configurations ........................................................................................................................ 10 2.1.2 Reserved I/O’s ............................................................................................................................. 10 2.2 UART ................................................................................................................................................... 10 3 Electrical Characteristics ............................................................................................................................ 11 3.1 Absolute Maximum Ratings ................................................................................................................ 11 3.2 Recommended Operating Conditions ................................................................................................. 11 3.3 DC Characteristics .............................................................................................................................. 11 3.4 Current Consumption .......................................................................................................................... 12 3.5 RF Characteristics ............................................................................................................................... 13 4 Physical Dimensions .................................................................................................................................. 17 5 Power-On Reset and Brownout Detector ................................................................................................... 19 6 Design Guidelines ...................................................................................................................................... 20 6.1 General Design Guidelines ................................................................................................................. 20 6.2 Layout Guide Lines ............................................................................................................................. 20 6.3 BLE121LR-A Layout Guide ................................................................................................................. 21 7 Soldering Recommendations ..................................................................................................................... 23 8 Block diagram ............................................................................................................................................. 24 9 Certifications ............................................................................................................................................... 27 9.1 Bluetooth ............................................................................................................................................. 27 9.2 FCC and IC ......................................................................................................................................... 27 9.2.1 FCC et IC ..................................................................................................................................... 28 9.3 CE ....................................................................................................................................................... 30 9.4 MIC Japan ........................................................................................................................................... 30 9.5 KCC (Korea) ........................................................................................................................................ 30 10 Contact Information................................................................................................................................. 31

Bluegiga Technologies Oy Page 6 of 31 1 BLE121LR Product numbering Available products and product codes Product code Description BLE121LR-A-M256K BLE121LR with an embedded chip antenna and with 256k internal flash

Bluegiga Technologies Oy Page 7 of 31 2 Pinout and Terminal Description Figure 1: BLE121LR Pin Number Pin Name Pad Type Description 1-3, 14, 15, 22 31-36 GND GND GND 13 AVDD Supply voltage 23 DVDD Supply voltage 7 Reset Reset Active low reset Table 1: Supply and RF Terminal Descriptions Pin Number Pin Name Pad Type Description 6 P0_0 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 5 P0_1 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 4 P0_2 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 8 P0_3 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping

Bluegiga Technologies Oy Page 8 of 31 9 P0_4 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 10 P0_5 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 11 P0_6 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 12 P0_7 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 30 P1_2 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 29 P1_3 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 28 P1_4 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 27 P1_5 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 17 P1_6 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 19 P2_0 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 20 P2_1 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping 21 P2_2 I/O Configurable Input/Output. See Table 4: Peripheral I/O Pin Mapping Table 2: Configurable I/O Terminals Pin Number Pin Name Pad Type Description 24 SCL I2C clock 25 SDA I2C data 18 DCDC_CNTRL Output On / by-pass control for an external DCDC converter Table 3: Non-configurable Terminals

Bluegiga Technologies Oy Page 9 of 31 HARDWARE.XML Example (*7654321076543210210A7 A6 A5 A4 A3 A2 A1 A0Alt.1CSS MO MI <usart channel="0" mode="spi_master" alternate="1" ...Alt.2MO MI CSS <usart channel="0" mode="spi_master" alternate="2" ...Alt.1RT CT TX RX <usart channel="0" mode="uart" alternate="1" ...Alt.2TX RX RT CT <usart channel="0" mode="uart" alternate="2" ...Alt.1MI MO CSS <usart channel="1" mode="spi_master" alternate="1" ...Alt.2MO CSS <usart channel="1" mode="spi_master" alternate="2" ...Alt.1RX TX RT CT <usart channel="1" mode="uart" alternate="1" ...Alt.2TX RT CT <usart channel="1" mode="uart" alternate="2" ...Alt.143210 <timer index="1" alternate="1" ...Alt.23 4 0 <timer index="1" alternate="2" ...Alt.11 0 <timer index="3" alternate="1" ...Alt.20<timer index="3" alternate="2" ...Alt.1 <timer index="4" alternate="1" ...Alt.20<timer index="4" alternate="2" ...DC DD5432P1PERIPHERAL / FUNCTIONP2USART 0 SPI (**RESERVEDRESERVEDDCDCCONTROLDEBUGOBSSELADCTIMER 3TIMER 4P0USART 0 UARTUSART 1 SPI (**USART 1 UARTTIMER 1 *) Refer to BLE Configuration Guide for detailed settings **) SS is the slave select signal when BLE121LR is set as SPI slave. When set as SPI master, any available I/O can be used as chip select signal of BLE121LR NOTE: Pins configured as peripheral I/O signals do not have pull-up / -down capability Table 4: Peripheral I/O Pin Mapping

Bluegiga Technologies Oy Page 10 of 31 2.1 I/O Ports 2.1.1 I/O Configurations Each I/O port can be configured as an input or output. When configured as input, each I/O port can also be configured with internal pull-up, pull-down or tri-state. Pull-down or pull-up can only be configured to whole port, not individual pins. Unused I/O pins should have defined level and not be floating. See the BLE Configuration Guide for more information about the configuration. During reset the I/O pins are configured as inputs with pull-ups. Note: Pins configured as peripheral I/O signals do not have pull-up / -down capability 2.1.2 Reserved I/O’s The high current driving pins P1_0 and P1_1 are reserved for the internal RF front end control. These pins are not exposed in BLE121LR and they can’t be used for application purposes. P1_7 is also used for the RF front end control but as an output it can be used to control the external DCDC for lowering the peak current drawn from the battery. The function of P1_7 can’t be altered. If external DCD is not used then P1_7 should be left not connected. 2.2 UART UART baud rate can be configured up 2 Mbps. See the BLE Configuration Guide for more information. Following table lists commonly used baud rates for BLE121LR Baud rate (bps) Error (%) 2400 0.14 4800 0.14 9600 0.14 14 400 0.03 19 200 0.14 28 800 0.03 38 400 0.14 57 600 0.03 76 800 0.14 115 200 0.03 230 400 0.03 Table 5: Commonly used baud rates for BLE121LR

Bluegiga Technologies Oy Page 11 of 31 3 Electrical Characteristics 3.1 Absolute Maximum Ratings Note: These are absolute maximum ratings beyond which the module can be permanently damaged. These are not maximum operating conditions. The maximum recommended operating conditions are in the Table 7. Rating Min Max Unit Storage Temperature -40 +85 °C AVDD, DVDD -0.3 3.9 V Other Terminal Volatages VSS-0.4 VDD+0.4 V Table 6: Absolute Maximum Ratings 3.2 Recommended Operating Conditions Rating Min Max Unit Operationg Temperature Range -40 +85 °C AVDD, DVDD (*,**,*** 2.0 3.6 V Table 7: Recommended Operating Conditions *) All supply nets must have the same voltage **) Supply voltage noise should be less than 10mVpp. Excessive noise at the supply voltage will reduce the RF performance. ***) The supply voltage has an impact on the TX power, see Figure 7. 3.3 DC Characteristics Parameter Test Conditions Min Typ Max Unit Logic-0 input voltage 0.5 V Logic-1 input voltage DVDD =3V0 2.5 V Logic-0 input current Input equals 0V -50 50 nA Logic-1 input current Input equals VDD -50 50 nA I/O pin pull-up and pull-down resistors 20 kΩ For detailed I/O terminal characteristic and timings refer to the CC2541 datasheet available in (http://www.ti.com/lit/ds/symlink/cc2541.pdf) Table 8: DC Characteristic

Bluegiga Technologies Oy Page 12 of 31 3.4 Current Consumption Power mode hardware.xml Min Typ Max Unit Transmit <txpower power = ”1”/> <slow clock enable = ”true”/> 25 mA <txpower power = ”9”/> <slow clock enable = ”true”/> 36 mA <txpower power = ”9”/> <slow clock enable = ”false”/> 38 mA Receive <slow clock enable = ”true”/> 28 mA <slow clock enable = ”false”/> 33 mA Power mode 1 2.7 mA Power mode 2 1.3 µA Power mode 3 0.5 µA Figure 2: BLE121LR TX peak current as a function of the setting in the HW configuration file Figure 3: BLE121LR TX peak current as a function of hardware.xml TXP setting (Example: <txpower power="9" bias="5" />)

Bluegiga Technologies Oy Page 14 of 31 Figure 6: Typical transmit power as a function of temperature Figure 7: BLE121LR transmit power as a function of supply voltage

Bluegiga Technologies Oy Page 15 of 31 Figure 8: BLE121LR TX power as a function of the setting in the HW configuration file (Example: <txpower power="9" bias="5" />) Figure 9: Radiation pattern of BLE121LR when mounted to the DKBLE

Bluegiga Technologies Oy Page 16 of 31 Figure 10: Radiation pattern of BLE121LR when mounted to the DKBLE Figure 11: Radiation pattern of BLE121LR when mounted to the DKBLE

Bluegiga Technologies Oy Page 17 of 31 4 Physical Dimensions PINOUT AND DIMENSIONS OF BLE121LR Figure 12: Footprint of BLE121LR (top view) Physical Dimensions of BLE121LR14.7 mm13.0 mm4.8 mm6.8 mm8.4 mm13.7 mm3.9 mm1.8 mm 1.8 mm1.9 mm Figure 13: Physical dimensions (top view) Physical Dimensions of BLE121LR14.7 mm13.0 mm4.8 mm6.8 mm8.4 mm13.7 mm3.9 mm1.8 mm 1.8 mm1.9 mm Figure 14: Physical dimensions (side view)

Bluegiga Technologies Oy Page 18 of 31 Figure 15: Recommended land pattern for BLE121LR-A

Bluegiga Technologies Oy Page 19 of 31 5 Power-On Reset and Brownout Detector BLE121LR includes a power-on reset (POR), providing correct initialization during device power on. It also includes a brownout detector (BOD) operating on the regulated 1.8-V digital power supply only. The BOD protects the memory contents during supply voltage variations which cause the regulated 1.8-V power to drop below the minimum level required by digital logic, flash memory, and SRAM. When power is initially applied, the POR and BOD hold the device in the reset state until the supply voltage rises above the power-on-reset and brownout voltages.

Bluegiga Technologies Oy Page 20 of 31 6 Design Guidelines 6.1 General Design Guidelines BLE121LR can be used directly with a coin cell battery. Due to relatively high internal resistance of a coin cell battery it is recommended to place a 100uF capacitor in parallel with the battery. The internal resistance of a coin cell battery is initially in the range of 10 ohms but the resistance increases rapidly as the capacity is used. Basically the higher the value of the capacitor the higher is the effective capacity of the battery and thus the longer the life time for the application. The minimum value for the capacitor depends on the end application and the maximum transmit power used. The leakage current of a 100uF capacitor is in the range of 0.5 uA to 3 uA and generally ceramic capacitors have lower leakage current than tantalum or aluminum electrolytic capacitors. Optionally TI’s TPS62730 can be used to reduce the current consumption during TX/RX and data processing stages. TPS62730 is an ultra-low power DC/DC converter with by-pass mode and will reduce the current consumption during transmission nominally by ~20% when using 3V coin cell battery. Figure 16: Example schematic for BLE121LR with a coin cell battery, TPS62730 DCDC converter and an I2C accelerometer 6.2 Layout Guide Lines Use good layout practices to avoid excessive noise coupling to supply voltage traces or sensitive analog signal traces. If using overlapping ground planes use stitching vias separated by max 3 mm to avoid emission from the edges of the PCB. Connect all the GND pins directly to a solid GND plane and make sure that there is a low impedance path for the return current following the signal and supply traces all the way from start to the end. A good practice is to dedicate one of the inner layers to a solid GND plane and one of the inner layers to supply voltage planes and traces and route all the signals on top and bottom layers of the PCB. This

Bluegiga Technologies Oy Page 21 of 31 arrangement will make sure that any return current follows the forward current as close as possible and any loops are minimized. Layout•Supply voltage–If possible use solid power plane–Make sure that solid GND plane follows the traces all the way–Do not route supply voltage traces across separated GND regions so that the path for the return current is cut•MIC input–Place LC filtering and DC coupling capacitors symmetrically as close to audio pins as possible–Place MIC biasing resistors symmetrically as close to microhone as possible.–Make sure that the bias trace does not cross separated GND regions (DGND -> AGND) so that the path for the return current is cut. If this is not possible the do not separate GND regions but keep one solid GND plane.–Keep the trace as short as possibleSignalsGNDPowerSignalsRecommended PCB layer configuration Figure 17: Typical 4-layer PCB construction Overlapping GND layers without GND stitching vias Overlapping GND layers with GND stitching vias shielding the RF energy Figure 18: Use of stitching vias to avoid emissions from the edges of the PCB 6.3 BLE121LR-A Layout Guide For optimal performance of the antenna place the module at the edge of the PCB as shown in the Figure 19. Do not place any metal (traces, components, battery etc.) within the clearance area of the antenna. Connect all the GND pins directly to a solid GND plane. Place the GND vias as close to the GND pins as possible. Use good layout practices to avoid any excessive noise coupling to signal lines or supply voltage lines. Do not place plastic or any other dielectric material in touch with the antenna. Min 17mm Min 17mmMetal clearanceareaBoard edge Figure 19: Recommended layout for BLE121LR-A

Bluegiga Technologies Oy Page 22 of 31 Figure 20: Poor layouts for BLE121LR

Bluegiga Technologies Oy Page 24 of 31 8 Block diagram BLE121LR is based on TI’s CC2541 chip. Embedded 32 MHz and 32.678 kHz crystals are used for clock generation. Matched balun and low pass filter provide optimal radio performance with extremely low spurious emissions. Balun + LPFChip antennaI/O controllerCC2541I/O32 MHz XTAL32.768 kHz XTALClockDebug interface8051 CPU core and memory arbitratorVoltage regulatorSRAMFlashAnalog comparatorOPAMPADCIRQ controller DMAUSART 0USART 1TIMER 1TIMER 2TIMER 3TIMER 4Radio arbiterRadio registersLink layer engineSRAMModulatorDemodulator SynthReceive TransmitFrequency synthetisizerResetPower-on reset2V –3.6V ResetPA/LNA BPF Figure 22: Simplified block diagram of BLE121LR CPU and Memory The 8051 CPU core is a single-cycle 8051-compatible core. It has three different memory access buses (SFR, DATA, and CODE/XDATA), a debug interface, and an 18-input extended interrupt unit. The memory arbiter is at the heart of the system, as it connects the CPU and DMA controller with the physical memories and all peripherals through the SFR bus. The memory arbiter has four memory-access points, access of which can map to one of three physical memories: an SRAM, flash memory, and XREG/SFR registers. It is responsible for performing arbitration and sequencing between simultaneous memory accesses to the same physical memory. The SFR bus is a common bus that connects all hardware peripherals to the memory arbiter. The SFR bus also provides access to the radio registers in the radio register bank, even though these are indeed mapped into XDATA memory space. The 8-KB SRAM maps to the DATA memory space and to parts of the XDATA memory spaces. The SRAM is an ultralow-power SRAM that retains its contents even when the digital part is powered off (power modes 2 and 3). The 256 KB flash block provides in-circuit programmable non-volatile program memory for the device, and maps into the CODE and XDATA memory spaces. Peripherals Writing to the flash block is performed through a flash controller that allows page-wise erasure and 4-bytewise programming. A versatile five-channel DMA controller is available in the system, accesses memory using the XDATA memory space, and thus has access to all physical memories. Each channel (trigger, priority, transfer mode,

Bluegiga Technologies Oy Page 25 of 31 addressing mode, source and destination pointers, and transfer count) is configured with DMA descriptors that can be located anywhere in memory. Many of the hardware peripherals (AES core, flash controller, USARTs, timers, ADC interface, etc.) can be used with the DMA controller for efficient operation by performing data transfers between a single SFR or XREG address and flash/SRAM. Each CC2541 contains a unique 48-bit IEEE address that can be used as the public device address for a Bluetooth device. Designers are free to use this address, or provide their own, as described in the Bluetooth specification. The interrupt controller services a total of 18 interrupt sources, divided into six interrupt groups, each of which is associated with one of four interrupt priorities. I/O and sleep timer interrupt requests are serviced even if the device is in a sleep mode (power modes 1 and 2) by bringing the CC2541 back to the active mode. The debug interface implements a proprietary two-wire serial interface that is used for in-circuit debugging. Through this debug interface, it is possible to erase or program the entire flash memory, control which oscillators are enabled, stop and start execution of the user program, execute instructions on the 8051 core, set code breakpoints, and single-step through instructions in the code. Using these techniques, it is possible to perform in-circuit debugging and external flash programming elegantly. The I/O controller is responsible for all general-purpose I/O pins. The CPU can configure whether peripheral modules control certain pins or whether they are under software control, and if so, whether each pin is configured as an input or output and if a pullup or pulldown resistor in the pad is connected. Each peripheral that connects to the I/O pins can choose between two different I/O pin locations to ensure flexibility in various applications. The sleep timer is an ultra-low power timer that uses an external 32.768-kHz crystal oscillator. The sleep timer runs continuously in all operating modes except power mode 3. Typical applications of this timer are as a real-time counter or as a wake-up timer to exit power modes 1 or 2. Timer 1 is a 16-bit timer with timer/counter/PWM functionality. It has a programmable prescaler, a 16-bit period value, and five individually programmable counter/capture channels, each with a 16-bit compare value. Each of the counter/capture channels can be used as a PWM output or to capture the timing of edges on input signals. It can also be configured in IR generation mode, where it counts timer 3 periods and the output is ANDed with the output of timer 3 to generate modulated consumer IR signals with minimal CPU interaction. Timer 2 is a 40-bit timer used by the Bluetooth low energy stack. It has a 16-bit counter with a configurable timer period and a 24-bit overflow counter that can be used to keep track of the number of periods that have transpired. A 40-bit capture register is also used to record the exact time at which a start-of-frame delimiter is received/transmitted or the exact time at which transmission ends. There are two 16-bit timer-compare registers and two 24-bit overflow-compare registers that can be used to give exact timing for start of RX or TX to the radio or general interrupts. Timer 3 and timer 4 are 8-bit timers with timer/counter/PWM functionality. They have a programmable prescaler, an 8-bit period value, and one programmable counter channel with an 8-bit compare value. Each of the counter channels can be used as PWM output. USART 0 and USART 1 are each configurable as either an SPI master/slave or a UART. They provide double buffering on both RX and TX and hardware flow control and are thus well suited to high-throughput full-duplex applications. Each USART has its own high-precision baud-rate generator, thus leaving the ordinary timers free for other uses. When configured as SPI slaves, the USARTs sample the input signal using SCK directly instead of using some oversampling scheme, and are thus well-suited for high data rates. The AES encryption/decryption core allows the user to encrypt and decrypt data using the AES algorithm with 128-bit keys. The AES core also supports ECB, CBC, CFB, OFB, CTR, and CBC-MAC, as well as hardware support for CCM. The ADC supports 7 to 12 bits of resolution with a corresponding range of bandwidths from 30-kHz to 4-kHz, respectively. DC and audio conversions with up to eight input channels (I/O controller pins) are possible. The inputs can be selected as single-ended or differential. The reference voltage can be internal, AVDD, or a single-ended or differential external signal. The ADC also has a temperature-sensor input channel. The ADC can automate the process of periodic sampling or conversion over a sequence of channels. The I2C module provides a digital peripheral connection with two pins and supports both master and slave

Bluegiga Technologies Oy Page 26 of 31 operation. I2C support is compliant with the NXP I2C specification version 2.1 and supports standard mode (up to 100 kbps) and fast mode (up to 400 kbps). In addition, 7-bit device addressing modes are supported, as well as master and slave modes.. The ultralow-power analog comparator enables applications to wake up from PM2 or PM3 based on an analog signal. Both inputs are brought out to pins; the reference voltage must be provided externally. The comparator output is connected to the I/O controller interrupt detector and can be treated by the MCU as a regular I/O pin interrupt. RF front end RF front end includes balun, power amplifier, low noise amplifier, band pass filter, and a ceramic chip antenna with matching network. Optimal matching combined with effective low pass filter provides extremely low in-band spurious emissions and harmonics.

Bluegiga Technologies Oy Page 27 of 31 9 Certifications BLE121LR is compliant to the following specifications. 9.1 Bluetooth TBA 9.2 FCC and IC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Bluegiga Technologies could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter meets both portable and mobile limits as demonstrated in the RF Exposure Analysis. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. IC Statements: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. OEM Responsibilities to comply with FCC and Industry Canada Regulations The BLE121LR module has been certified for integration into products only by OEM integrators under the following condition:  The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

Bluegiga Technologies Oy Page 28 of 31 IMPORTANT NOTE: In the event that the above condition can not be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. End Product Labeling The BLE121LR module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: QOQBLE121LR” “Contains Transmitter Module IC: 5123A-BGTBLE121LR” or “Contains FCC ID: QOQBLE121LR” “Contains IC: 5123A-BGTBLE121LR” The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. 9.2.1 FCC et IC Déclaration d’IC : Ce dispositif est conforme aux normes RSS exemptes de licence d’Industrie Canada. Son fonctionnement est assujetti aux deux conditions suivantes : (1) ce dispositif ne doit pas provoquer de perturbation et (2) ce dispositif doit accepter toute perturbation, y compris les perturbations qui peuvent entraîner un fonctionnement non désiré du dispositif. Selon les réglementations d’Industrie Canada, cet émetteur radio ne doit fonctionner qu’avec une antenne d’une typologie spécifique et d’un gain maximum (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Pour réduire les éventuelles perturbations radioélectriques nuisibles à d’autres utilisateurs, le type d’antenne et son gain doivent être choisis de manière à ce que la puissance isotrope rayonnée équivalente (P.I.R.E.) n’excède pas les valeurs nécessaires pour obtenir une communication convenable. Responsabilités des OEM quant à la conformité avec les réglementations de FCC et d’Industrie Canada Les modules BLE121LR ont été certifiés pour entrer dans la fabrication de produits exclusivement réalisés par des intégrateurs dans les conditions suivantes :  Le module transmetteur ne doit pas être installé ou utilisé en concomitance avec une autre antenne ou un autre transmetteur. Tant que ces deux conditions sont réunies, il n’est pas nécessaire de procéder à des tests supplémentaires sur le transmetteur. Cependant, l’intégrateur est responsable des tests effectués sur le produit final afin de se

Bluegiga Technologies Oy Page 29 of 31 mettre en conformité avec d’éventuelles exigences complémentaires lorsque le module est installé (exemple : émissions provenant d’appareils numériques, exigences vis-à-vis de périphériques informatiques, etc.) REMARQUE IMPORTANTE : En cas d’inobservance de ces conditions (en ce qui concerne certaines configurations ou l’emplacement du dispositif à proximité d’un autre émetteur), les autorisations de FCC et d’Industrie Canada ne seront plus considérées valables et l’identification de FCC et le numéro de certification d’IC ne pourront pas être utilisés sur le produit final. Dans ces cas, l’intégrateur OEM sera chargé d’évaluer à nouveau le produit final (y compris l’émetteur) et d’obtenir une autorisation indépendante de FCC et d’Industrie Canada. Étiquetage du produit final Le module BLE121LR est étiqueté avec sa propre identification FCC et son propre numéro de certification IC. Si l’identification FCC et le numéro de certification IC ne sont pas visibles lorsque le module est installé à l’intérieur d’un autre dispositif, la partie externe du dispositif dans lequel le module est installé devra également présenter une étiquette faisant référence au module inclus. Dans ce cas, le produit final devra être étiqueté sur une zone visible avec les informations suivantes : « Contient module émetteur identification FCC : QOQBLE121LR » « Contient module émetteur IC : 5123A-BGTBLE121LR » ou « Contient identification FCC : QOQBLE121LR » « Contient IC : 5123A-BGTBLE121LR » Dans le guide d’utilisation du produit final, l’intégrateur OEM doit s’abstenir de fournir des informations à l’utilisateur final portant sur les procédures à suivre pour installer ou retirer ce module RF ou pour changer les paramètres RF. .

Bluegiga Technologies Oy Page 30 of 31 9.3 CE TBA 9.4 MIC Japan TBA 9.5 KCC (Korea) TBA .

Bluegiga Technologies Oy Page 31 of 31 10 Contact Information Sales: sales@bluegiga.com Technical support: http://www.bluegiga.com/support Orders: orders@bluegiga.com WWW: www.bluegiga.com Head Office / Finland: Phone: +358-9-4355 060 Fax: +358-9-4355 0660 Sinikalliontie 5A 02630 ESPOO FINLAND Postal address / Finland: P.O. BOX 120 02631 ESPOO FINLAND Sales Office / USA: Phone: +1 770 291 2181 Fax: +1 770 291 2183 Bluegiga Technologies, Inc. 3235 Satellite Boulevard, Building 400, Suite 300 Duluth, GA, 30096, USA Sales Office / Hong-Kong: Bluegiga Technologies Ltd. Phone: +852 3972 2186

Navigation menu