Silicon Laboratories Finland MGM12P3 MGM12P2 802.15.4 module User Manual User Guide

Download:
Mirror Download [FCC.gov]
Document ID	3490225
Application ID	xpPAJyNrc9yZcielQD+4lA==
Document Description	User Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.93kB (436642 bits)
Date Submitted	2017-07-31 00:00:00
Date Available	2017-08-01 00:00:00
Creation Date	2017-07-28 14:11:33
Producing Software	Microsoft® Word 2016
Document Lastmod	2017-07-28 14:11:33
Document Title	User Guide
Document Creator	Microsoft® Word 2016
Document Author:	Lauren Lehman

INSTALLATION GUIDE
Alberga Business Park, Bertel Jungin aukio 3
FI-02600 Espoo, Finland
Phone: +358 9 435 5060
www.silabs.com
Figure 9.4: Recommended PCB Land Pattern
Qualified Antenna Types
This device has been designed to operate with a standard 2.14 dBi dipole antenna. Any
antenna of a different type or with a gain higher than 2.14 dBi is strictly prohibited for use
with this device. Using an antenna of a different type or gain more than 2.14 dBi will require
additional testing for FCC, CE and IC. The required antenna impedance is 50 Ω.
Antenna type
Dipole
Maximum gain
2.14 dBi
Table 1: Qualified antennas for MGM12Px
CE
The MGM12P02 and MGM12P22 modules are in conformity with the essential requirements
and other relevant requirements of the Radio Equipment Directive(RED). Please note that
every application using the MGM12P will need to perform the radio EMC tests on the end
product according toEN 301 489-17. Separate RF testing is not required provided that the
customer follows the module manufacturer's recommendations and instructions and does
not make modifications e.g. to the provided antenna solutions or requirements. A formal DoC
is available via www.silabs.com
MGM12P32 module is inconformity with the essential requirements and other relevant
requirements of the Radio Equipment Directive(RED) at nominal 10 dBm transmit power.
The transmit power of the module is not limited and when an end product is using
MGM12P32, the end product manufacturer is responsible that the end product is in
inconformity of all relevant requirements of the RED.
Page 2 of 7
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by Silicon Labs could void the user’s authority to
operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter meets both portable and mobile limits as
demonstrated in the RF Exposure Analysis. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter except in accordance with
FCC multi-transmitter product procedures.
OEM Responsibilities to comply with FCC Regulations
OEM integrator is responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
•
•
•
With MGM12P22GA, MGM12P22GE, MGM12P02GA and MGM12P02GE the
antenna(s) must be installed such that a minimum separation distance of 6.7mm is
maintained between the radiator (antenna) and all persons at all times.
With MGM12P32GA and MGM12P32GE the antenna(s) must be installed such that a
minimum separation distance of 39mm is maintained between the radiator (antenna)
and all persons at all times.
The transmitter module must not be co-located or operating in conjunction with any
other antenna or transmitter except in accordance with FCC multi-transmitter product
procedures.
IMPORTANT NOTE: In the event that the above conditions cannot be met (for certain
configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The variants of MGM12P Modules are labeled with their own FCC IDs. If the FCC ID is not
visible when the module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed module. In
that case, the final product must be labeled in a visible area with the following:
Page 3 of 7
MODELS MGM12P02GE and MGM12P02GA:
“Contains Transmitter Module FCC ID: QOQMGM12P0”
or
“Contains FCC ID: QOQMGM12P0
MODELS MGM12P22GE and MGM12P22GA:
“Contains Transmitter Module FCC ID: QOQMGM12P2”
or
“Contains FCC ID: QOQMGM12P2
MODELS MGM12P32GE and MGM12P32GA:
“Contains Transmitter Module FCC ID: QOQMGM12P3”
or
“Contains FCC ID: QOQMGM12P3
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module or change RF related parameters in the user
manual of the end product.
ISED Canada
This radio transmitter (IC: 5123A-MGM12P0, IC: 5123A-MGM12P2 and IC: 5123AMGM12P3) has been approved by Industry Canada to operate with the antenna types listed
above with the maximum permissible gain indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device
This device complies with Industry Canada’s license-exempt RSS standards. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device
RF Exposure Statement
Exception from routine SAR evaluation limits are given in RSS-102 Issue 5.
MGM12P22GA, MGM12P22GE, MGM12P02GA and MGM12P02GE modules meets the
given requirements when the minimum separation distance to human body is 20 mm.
MGM12P32GA and MGM12P32GA modules meets the given requirements when the
minimum separation distance to human body is 35 mm.
RF exposure or SAR evaluation is not required when the separation distance is same or
more than stated above. If the separation distance is less than stated above the OEM
integrator is responsible for evaluating the SAR.
OEM Responsibilities to comply with IC Regulations
Page 4 of 7
The MGM12P module has been certified for integration into products only by OEM
integrators under the following conditions:
•
•
The antenna(s) must be installed such that a minimum separation distance as stated
above is maintained between the radiator (antenna) and all persons at all times.
The transmitter module must not be co-located or operating in conjunction with any
other antenna or transmitter.
As long as the two conditions above are met, further transmitter testing will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example, digital
device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain
configurations or co-location with another transmitter), then the ISEDC authorization is no
longer considered valid and the IC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate ISEDC authorization.
End Product Labeling
The MGM12P modules are labeled with their own IC ID. If the IC ID is not visible when the
module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. In that case,
the final end product must be labeled in a visible area with the following:
MODELS MGM12P02GE and MGM12P02GA:
“Contains Transmitter Module IC: 5123A-MGM12P0”
or
“Contains IC: 5123A-MGM12P0
MODELS MGM12P22GE and MGM12P22GA:
“Contains Transmitter Module IC: 5123A-MGM12P2”
or
“Contains IC: 5123A-MGM12P2
MODELS MGM12P32GE and MGM12P32GA:
“Contains Transmitter Module IC: 5123A-MGM12P3”
or
“Contains IC: 5123A-MGM12P3”
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module or change RF related parameters in the user
manual of the end product
ISEDC (Français)
Industrie Canada a approuvé l’utilisation de cet émetteur radio (IC: 5123A-MGM12P0, IC:
5123A-MGM12P2, IC: 5123A-MGM12P3) en conjonction avec des antennes de type
dipolaire à 2.14dBi ou des antennes embarquées, intégrée au produit. L’utilisation de tout
autre type d’antenne avec ce composant est proscrite. Ce composant est conforme aux
normes RSS, exonérées de licence d'Industrie Canada. Son mode de fonctionnement est
soumis aux deux conditions suivantes :
Page 5 of 7
1. Ce composant ne doit pas générer d’interférences
2. Ce composant doit pouvoir est soumis à tout type de perturbation y compris celle pouvant
nuire à son bon fonctionnement.
Déclaration d'exposition RF
L'exception tirée des limites courantes d'évaluation SAR est donnée dans le document RSS102 Issue 5. Les modules MGM12P22GA, MGM12P22GE, MGM12P02GA et GM12P02GE
répondent aux exigences requises lorsque la distance minimale de séparation avec le corps
humain est de 20 mm.
Les modules MGM12P32GA et MGM12P32GA répondent aux exigences requises lorsque la
distance minimale de séparation avec le corps humain est de 35 mm.
La déclaration d’exposition RF ou l'évaluation SAR n'est pas nécessaire lorsque la distance
de séparation est identique ou supérieure à celle indiquée ci-dessus. Si la distance de
séparation est inférieure à celle mentionnées plus haut, il incombe à l'intégrateur OEM de
procédé à une évaluation SAR.
Responsabilités des OEM pour une mise en conformité avec le Règlement du Circuit
Intégré
Le module MGM12P a été approuvé pour l'intégration dans des produits finaux
exclusivement réalisés par des OEM sous les conditions
suivantes:
• L'antenne (s) doit être installée de sorte qu'une distance de séparation minimale indiquée
ci-dessus soit maintenue entre le radiateur
(antenne) et toutes les personnes avoisinante, ce à tout moment.
• Le module émetteur ne doit pas être localisé ou fonctionner avec une autre antenne ou un
autre transmetteur que celle indiquée plus haut.
Tant que les deux conditions ci-dessus sont respectées, il n’est pas nécessaire de tester ce
transmetteur de façon plus poussée. Cependant, il incombe à l’intégrateur OEM de s’assurer
de la bonne conformité du produit fini avec les autres normes auxquelles il pourrait être
soumis de fait de l’utilisation de ce module (par exemple, les émissions des périphériques
numériques, les exigences de périphériques PC, etc.).
REMARQUE IMPORTANTE: dans le cas où ces conditions ne peuvent être satisfaites (pour
certaines configurations ou co-implantation avec un autre émetteur), l'autorisation ISEDC
n'est plus considérée comme valide et le numéro d’identification ID IC ne peut pas être
apposé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera responsable de
la réévaluation du produit final (y compris le transmetteur) et de l'obtention d'une autorisation
ISEDC distincte.
Étiquetage des produits finis
Les modules MGM12P sont étiquetés avec leur propre ID IC. Si l'ID IC n'est pas visible
lorsque le module est intégré au sein d'un autre produit, cet autre produit dans lequel le
module est installé devra porter une étiquette faisant apparaitre les référence du module
intégré. Dans un tel cas, sur le produit final doit se trouver une étiquette aisément lisible sur
laquelle figurent les informations suivantes :
MODÈLES MGM12P02GE et MGM12P02GA:
"Contient le module transmetteur : 5123A-MGM12P0"
ou
"Contient le circuit: 5123A-MGM12P0
MODÈLES MGM12P22GE et MGM12P22GA:
"Contient le module transmetteur: 5123A-MGM12P2"
Page 6 of 7
ou
"Contient IC: 5123A-MGM12P2
MODÈLES MGM12P32GE et MGM12P32GA:
"Contient le module émetteur IC: 5123A-MGM12P3"
ou
"Contient IC: 5123A-MGM12P3"
L'intégrateur OEM doit être conscient qu’il ne doit pas fournir, dans le manuel d’utilisation,
d'informations relatives à la façon d'installer ou de d’enlever ce module RF ainsi que sur la
procédure à suivre pour modifier les paramètres liés à la radio.
Page 7 of 7

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 7
Language                        : fi-FI
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Creator                         : Lauren Lehman
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2017:07:28 14:11:33+03:00
Modify Date                     : 2017:07:28 14:11:33+03:00
Document ID                     : uuid:857C1A29-7B31-431E-B1F8-099EF6D3F92B
Instance ID                     : uuid:857C1A29-7B31-431E-B1F8-099EF6D3F92B
Author                          : Lauren Lehman

EXIF Metadata provided by EXIF.tools