Silicon Labs RS9110N1103 802.11 abgn MODULE User Manual
Redpine Signals Inc 802.11 abgn MODULE
Contents
- 1. User Manual
- 2. Certification Leaflet
Certification Leaflet
WLAN Access Point Card
MODEL: CG2102
CONTAINS FCC ID: XF6-RS9110N1103
CONTAINS IC: 8407A-RS9110N1103
CAN ICES-3 (B)/NMB-3(B)
Certification Leaflet
Federal communications commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly
approved by Option could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada license-exempt RSS standard(s)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Exposure Information to Radio Frequency Energy
Users concerned with the risk of Radio Frequency exposure may wish to limit the duration of their calls and to position the
antenna as far away from the body as is practical.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than
necessary for successful communication.
Notification d’exposition aux radiofréquences
Le présent appareil est conforme aux limites d’exposition aux radiofréquences (RF) du CNR-102 pour utilization par le
grand public (environnement non contrôlé). En plus, le produit doit être installé de manière à assurer une distance de
séparation de 20 cm minimum entre le corps de l’utilisateur et les antennes.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un
type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
External antennas
The max allowed antenna gain to comply with the RF Exposure and radiated output power requirements is 3 dBi.
In addition the product shall be installed in a way that a distance of at least 20 cm is maintained between the antennas
and the user’s body.
External antennas
This radio transmitter, IC: 8407A-RS9110N1103, has been approved by Industry Canada to operate with the antenna
types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
2.4GHz band: 3dBi (50Ω)
5GHz band: 3dBi (50Ω)
Antennes externes
Le présent émetteur radio, IC 8407A-RS9110N1103, a été approuvé par Industrie Canada pour fonctionner avec les
types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type
d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
2.4GHz: 3dBi (50Ω)
5GHz band: 3dBi (50Ω)
5GHz WLAN operation
Operation in the 5.15 - 5.25 GHz frequency band (channels 36 to 48) is restricted to indoor usage only in order to reduce
the potential for harmful interference to co-channel mobile satellite systems.
The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified
for point-to-point and non point-to-point operation as appropriate.
Opération 5GHz
Les dispositifs fonctionnant dans la bande 5 150-5 250 MHz (canaux 36 à 48) sont réservés uniquement pour une
utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux.
Le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz)doit se conformer à la limite
de p.i.r.e. spécifiée pour l'exploitation point à point et non point à point, selon le cas.
Manufacturer's Disclaimer Statement
The information in this document is subject to change without notice and does not represent a commitment on the part of
the vendor. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy, or
fitness for any particular purpose of this document. The manufacturer reserves the right to make changes to the content of
this document and/or the products associated with it at any time without obligation to notify any person or organization of
such changes. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages.
For questions regarding your product or declaration, contact:
Option | Gaston Geenslaan 14 | 3001 Leuven | Belgium | www.option.com
To identify this product we refer to the Part, Series, or Model number found on the product.