Skidata COX70ITDMC Coder working with 123kHz and 13.56 MHz keycards User Manual Cover COx70TDMC 1 0 en
Skidata AG Coder working with 123kHz and 13.56 MHz keycards Cover COx70TDMC 1 0 en
Skidata >
User manual
Manual
Coder CO x70i TDM/C
Installation & Maintenance Instructions Coder CO x70i TDM/C
Page 2 © SKIDATA AG, April 2003
SKIDATA AG
Technical Documentation
Untersbergstrasse 40
A-5083 Gartenau
Telephone +43-(0)6246 888,
Telefax +43-(0)06246 8887
Internet http://www.skidata.com
e-mail docu@skidata.com
Copyright
© 2003 by SKIDATA AG. All rights reserved. All information in the
following document is protected by copyright law. No part of this
document may be reproduced without the written consent of SKI-
DATA AG. SKIDATA AG reserves the right to make any changes
of specification and other information in this document without
further notice.
Please note
During the compilation of this Technical Documentation, great
care has been taken to ensure the accuracy of the information
contained in it. However, despite our constant effort to ensure the
highest degree of accuracy and comprehensiveness possible,
the information provided cannot be guaranteed to be absolutely
error-free.
Trademarks
This documentation may contain representations of registered
product or service trademarks owned by SKIDATA AG or third
parties, as well as references to proprietary know-how protected
by copyright laws or other legal provisions. In any case the intel-
lectual property rights remain exclusively with their respective
owners.
Declaration of Conformity
The Coders of the CO x70i TDM/C product family have been de-
veloped, designed and manufactured in accordance with the
following EU directions:
R&TTE (99/5/EC)
0408
List of EU countries where these Coders may be sold:
AT, BE, DE, DK, ES, FI, FR, GB, GR, IE, IT, LU, NL, PT, SE
Version April 2003
Coder models CO x70i TDM/C Installation & Maintenance instructions
© SKIDATA AG, April 2003 Page 3
FCC 15.19 :
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause un-
desired operation.
FCC 15.21 :
IMPORTANT: Any changes to or modifications of CO x70i
TDM/C unless expressly approved by SKIDATA™, may void the
user's authority to operate this device.
Installation & Maintenance Instructions Coder CO x70i TDM/C
Page 4 © SKIDATA AG, April 2003
Coder CO x70i TDM/C 1
Document Management – Version Table
Tab. 1: Document Version Table for Installation & Maintenance Instructions
Section Document Pages Version Date
1 Coder CO x70i TDM/C 6 1.0 28-04-2003
Coder CO x70i TDM/C 1
1
Coder
CO x70i TDM/C
Version 1.1
4 pages
Copyright 2003 by SKIDATA AG
Coder CO x70i TDM/C 1
Electrical connections of the device 1.2
© SKIDATA AG, Version 1.1 Page 3
1.2 Electrical connections of the
device
Plug the D-sub connector of the power adapter into the power
D-sub port of the printer.
Use the supplied interface cable to connect the interface port
on the printer to the COM 1 port on the PC.
Plug in the power adapter
Fig. 1:
Back-View
Fig. 2:
Connection layput
1 Coder CO x70i TDM/C
1.2 Electrical connections of the device
Page 4 © SKIDATA AG, Version 1.1