Skyrocket Toys 01206TX24G Remote Control for a Sky Viper Quadcopter User Manual Print
Skyrocket Toys LLC Remote Control for a Sky Viper Quadcopter Print
Exhibit 08 Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1970652 |
| Application ID | 7oh+1f+4fhY179/MNIBaug== |
| Document Description | Exhibit 08 Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 449.26kB (5615777 bits) |
| Date Submitted | 2013-05-22 00:00:00 |
| Date Available | 2013-05-22 00:00:00 |
| Creation Date | 2013-04-25 14:46:13 |
| Producing Software | Adobe PDF library 9.90 |
| Document Lastmod | 2013-05-10 18:56:34 |
| Document Title | |
| Document Creator | Adobe Illustrator CS5.1 |
TROUBLESHOOTING (Problem / Solution) Quadcopter is unresponsive or behaving erratically Ensure the remote has fresh batteries and the LiPo battery is fully charged. Ensure your remote is within unobstructed view of Quadcopter and you are within 20 feet range. Electronic interference may be caused by another source or Quadcopter may be launched from an unlevel surface. Turn the remote off and unplug Quadcopter’s battery for 30 seconds then turn them back on and try from a flat, level launching surface. - Inspect Quadcopter for any possible damage - Ensure that damaged foam body rings are not interfering with propeller movement. Quadcopter drifts in any direction during flight without direction from the remote - Adjust the trim controls during flight until drifting ceases Quadcopter crashes immediately - Propellers may be installed in the wrong position. Ensure proper installation. Quadcopter crashes during when attempting stunt functions - Ensure that Quadcopter is flying a minimum distance of 6 feet from the ground with a minimum 6 feet clearance in all directions. This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help. BATTERY CAUTIONS: •Do not use rechargeable batteries. •Non-rechargeable batteries are not to be recharged. •Different types of batteries or new and old batteries are not to be mixed. •Batteries are to be inserted using correct polarity. •Remove exhausted batteries as soon as possible and discard properly. •Remove all batteries from compartment if toy is not used for a long period (seven months). •The supply terminals are not to be short circuited. LiPo BATTERY CAUTIONS: - Keep away from flammable materials. - Do not expose to direct sunlight. - Do not place in fires or leave in hot places. - Do not drop or make subject to strong impact - Keep dry and away from water. Loosen screws in remote battery compartment door and insert batteries as shown. Replace doors and tighten screws. LiPo batteries must be recycled or disposed of properly. They should not be disposed of with other household waste. Check your local laws and regulations for correct recycling and/or battery disposal. Contact Skyrocket Customer Support for information regarding replacement bodies, batteries and propeller blades and to redeem this special offer! ©2013 Skyrocket Toys LLC, Venice CA 90291 USA. All Rights Reserved. Sky Viper and the Skyrocket logo are trademarks of Skyrocket Toys LLC. MADE IN CHINA. CAUTION: ELECTRIC TOY NOT RECOMMENDED FOR CHILDEN UNDER 8 YEARS OF AGE. AS WITH ALL ELECTRONIC PRODUCTS, PRECAUTIONS SHOULD BE OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK. INPUT: AC 100-240V 50/60HZ 0.2A. OUTPUT: 4.2V DC 800MA. INSTALLING REMOTE BATTERIES LiPo BATTERY DISPOSAL INSTRUCTIONS: BONUS REPLACEMENT BODY & BATTERY OFFER! ADULT SUPERVISION REQUIRED: QUESTIONS OR COMMENTS? www.Sky-Viper.com/support email – support@skyrockettoys.com phone – 1-888-674-5650 4 x AAA (LR03) 1.5V An adult should periodically check this product and the LiPo battery to ensure no damage or hazards exist. Spinning blades can cause injury. Adequate flying space is required. Avoid flying near interior fans and/or vents as they may make flying difficult to control. Keep a safe distance away from streets, public thoroughfares, bodies of water and power lines. Do not fly near spectators or animals. Keep spinning rotors away from fingers, hair, eyes and other body parts. Always launch from a flat surface. Never launch from your hand. Read all enclosed information before operating. THIS PRODUCT CONTAINS A LITHIUM-POLYMER BATTERY 3.7V 500mAH: LiPo batteries have a severe risk of fire and injury if they are improperly handled or misused. They may explode, overheat or ignite. Read all following precautions and instructions regarding the care and use of LiPo batteries. The enclosed LiPo battery is only to be used with the vehicle and charger included with this product. Remove all packaging attachments before giving the toy to a child. Not suitable for children under 3 years due to small parts that could be swallowed. Keep fingers, hair and loose clothing away from tires and wheels. Keep instructions for future reference. Do not discard. Conforms to product safety standards ASTM F963. Contents: R/C Quadcopter, Remote Control, Full Body Hull, Ultra-Light Stunt Body, 4 Replacement Blades, Rechargeable 3.7V 500mAH LiPo Battery, Charger, Screw Driver, Screws, Adhesive Strips and Instructions CHARGING & INSTALLING LiPo BATTERY IN QUADCOPTER Unplug and remove LiPo Battery from underside of Quadcopter. Plug LiPo battery into AC power adaptor and charge for 30-50 minutes. (RED light = Charging / GREEN light = Fully Charged) Once charged, disconnect LiPo battery from AC power adaptor and reassemble back into underside of Quadcopter for flying. NOTE: Always unplug LiPo battery when Quadcopter is not in use. After use, allow LiPo battery 15 minutes to cool before charging. Charge LiPo battery in an isolated area Never leave LiPo battery unattended while charging. If LiPo battery swells, unplug it immediately and permanently discontinue use. FLYING QUADCOPTER LAUNCHING Install LiPo battery and place Quadcopter on flat smooth surface. Turn remote control power switch to ON. IMPORTANT: Quadcopter calibrates when remote is turned on, so SURFACE MUST BE LEVEL. Launching from uneven surfaces may affect flying performance. Ensure surrounding area is free of obstacles and suitable for flying. HELPFUL TIP: Stand behind Quadcopter when launching so you are facing what Quadcopter is facing. This makes flying easier. Slowly push remote control Throttle stick UP until Quadcopter lifts into the air. CAUTION: DO NOT FLY NEAR SPECTATORS OR ANIMALS. READ ALL WARNINGS IN THIS MANUAL BEFORE FLYING. LOW VOLTAGE PROTECTION: - If battery voltage drops to an extremely low level, Quadcopter will severe battery electrical supply preventing any possible damage to battery or Quadcopter. Lipo battery will need to be recharged to restore function. - Unplug LiPo battery on Quadcopter. - Turn foam body upside down and rest on level surface. - Turn Quadcopter upside down and place it over foam body, aligning 4 rotor arms with foam body’s 4 plastic clips. Ensure that GREEN blades are facing forward with foam body. - Insert Quadcopter into plastic clips. Snap clips closed to secure Quadcopter to foam body then flip back to upright position. - Flip Body Switch on remote control to ON. - NOTE: Do not carry Quadcopter by foam rings as this may cause unnecessary damage to foam body. Forward/Backward Trim Throttle/Spin(Yaw) Stick Direction Stick ATTACHING THE ULTRA-LIGHT STUNT BODY - Unplug LiPo battery on Quadcopter. - Place stunt body over Quadcopter, aligning 4 side holes with 4 rotor arms. Ensure that stunt body points forward between the GREEN blades. - Gently press stunt body down until holes clip over rotor arms. - Flip Body Switch on remote control to OFF. REPAIR & MAINTAINENCE The foam body is designed to protect Quadcopter from impact and improve your flying experience. Overtime however the foam body will become damaged and break. DO NOT RETURN QUADCOPTER TO YOUR LOCAL RETAILER. You can repair or replace the foam body and propeller blades as follows: FOAM BODY REPAIR Power indicator LED Stunt Button - If Quadcopter’s blades become jammed and users continue to throttle up causing a high current, Quadcopter will severe battery connection protecting it from over current. Lipo battery will need to be unplugged then reconnected to restore function. ATTACHING THE FOAM 4-RING BODY HULL Power On/Off Switch 4-Ring Body On/Off Switch Repair a break in the foam body by applying adhesive binding strips to the damaged area. Applying 2 binding strips in a criss-cross pattern across a damaged area will increase repair strength. Inspect foam body regularly for signs of damage. GREEN Cracks in progress can be reinforced with repair strips before full breaks occur. CHANGING DAMAGED PROPELLER BLADES - Remove the small retaining screw holding the damaged blade in place using the mini screwdriver provided. - Make note of the blade color and letter (A,B,C or D) before removing the blade from Quadcopter. - Replace the damaged blade with a new blade with matching color and letter. Secure the blade with the retaining screw. Flip quadcopter upside down to see blade markings WARNING: Do not fly with broken or damaged propeller blades as it may cause damage or lead to injury. Spin (Yaw) Trim Flight Sensitivity Dial Left/Right Trim FLIGHT CONTROL Press Throttle stick UP to climb Press Throttle stick DOWN to descend Press Throttle stick LEFT to spin (yaw) to the left Press Throttle stick RIGHT to spin (yaw) to the right Press Direction stick UP to fly forward Press Direction stick DOWN to fly backward Press Direction stick LEFT to fly left Press Direction stick RIGHT to fly right ONE-TOUCH STUNT FUNCTIONS (For use with stunt body or no body at all—Do not perform stunts with 4-ring foam body attached) - Tap the Direction stick in one of 4 directions while pressing the Stunt Button to do amazing flips and barrel rolls! - FLIP FORWARD: Tap Direction stick UP while pressing Stunt Button. - FLIP BACKWARD: Tap Direction stick DOWN while pressing Stunt Button. - FLIP LEFT: Tap Direction stick LEFT while pressing Stunt Button. - FLIP RIGHT: Tap Direction stick RIGHT while pressing Stunt Button. IMPORTANT: QUADCOPTER SHOULD BE FLYING AT LEAST 6 FEET IN THE AIR WITH A MINIMUM CLEARANCE OF 6 FEET IN ALL DIRECTIONS BEFORE ATTEMPTING STUNT FUNCTIONS. STUNT FUNCTIONS SHOULD BE PERFORMED OUTSIDE ONLY. FLIGHT SENSITIVITY ADJUSTMENT: Quadcopter responsiveness may be adjusted to match your flying skills. Rotate knob CLOCKWISE to increase responsiveness. Rotate COUNTER-CLOCKWISE to decrease responsiveness. BLACK
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : 3.1-701 Format : application/pdf Title : Print Metadata Date : 2013:05:10 18:56:34+08:00 Modify Date : 2013:05:10 18:56:34+08:00 Create Date : 2013:04:25 14:46:13-07:00 Creator Tool : Adobe Illustrator CS5.1 Thumbnail Width : 256 Thumbnail Height : 176 Thumbnail Format : JPEG Thumbnail Image : (Binary data 22296 bytes, use -b option to extract) Instance ID : uuid:8ffc0a8c-5635-470c-bb1d-05c8eddef944 Document ID : xmp.did:4538A9A61AADE211BC58F5116AD6166D Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : uuid:ae9148ef-3000-a144-9ee3-ddb3557e196e Derived From Document ID : xmp.did:8AF5709C0E20681188C6A12CE4B46A4D Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved History Instance ID : xmp.iid:4538A9A61AADE211BC58F5116AD6166D History When : 2013:04:25 14:46:13-07:00 History Software Agent : Adobe Illustrator CS5.1 History Changed : / Manifest Link Form : EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference Manifest Reference File Path : C:\Users\Petrick Mc Arthur\Documents\Clients\SkyRocket\VMD\4Blade Helibomber\SkyViper\svinstructionsillustrations3\B.tif, C:\Users\Petrick Mc Arthur\Documents\Clients\SkyRocket\VMD\4Blade Helibomber\SkyViper\Instructions\Quadcopter logo.psd, C:\Users\Petrick Mc Arthur\Documents\Clients\SkyRocket\VMD\4Blade Helibomber\SkyViper\SkyViper\Sky Viper\SkyViper Print File\Sky Viper Logo.psd, C:\Users\Petrick Mc Arthur\Documents\Clients\SkyRocket\VMD\4Blade Helibomber\SkyViper\Instructions\Copter and swoosh.psd Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : True N Pages : 1 Max Page Size W : 11.692912 Max Page Size H : 8.267782 Max Page Size Unit : Inches Font Name : FranklinGothic-Medium, FranklinGothic-Book Font Family : Franklin Gothic Medium, Franklin Gothic Book Font Face : Regular, Regular Font Type : Open Type, Open Type Font Version : Version 5.01, Version 2.01 Font Composite : False, False Font File Name : framd.ttf, FRABK.TTF Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : Brights Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Cyan : 60.000002 Swatch Groups Colorants Magenta : 90.000004 Swatch Groups Colorants Yellow : 0.003099 Swatch Groups Colorants Black : 0.003099 Producer : Adobe PDF library 9.90 Page Count : 2 Creator : Adobe Illustrator(R) 15.0 For : Petrick Mc Arthur, Bounding Box : 27 -584 845 -24 Creator Version : 15 Container Version : 11EXIF Metadata provided by EXIF.tools