Skyrocket Toys 01598TX24G Sky Viper Nano Drone-Remote User Manual 01598 ENF16 SVNano IM 050416 PREVIEW

Skyrocket Toys LLC Sky Viper Nano Drone-Remote 01598 ENF16 SVNano IM 050416 PREVIEW

User manual

1 23 421OFFLOW21OFFHIGHOnline Video Instructions & Flying Tips available now at SKYVIPER.COMFLYING TIPSPOWERING UP AND PAIRING (WITH ALTITUDE ON) FLYING GUIDEPress Auto Launch to launch a few feet off the ground.Press the directional Thumbstick to fly in any direction. Press the Altitude button to fly approximately 12” higher or lower.Press the Auto Land button to land. Turn on drone. Turn on remote. Wait for flashing green lights to turn solid.FLYING BASICSPlace drone on flat surface.TOGGLE INTO MANUAL FLIGHT WHILE IN AUTO-HOVER• Hold stunt button and press auto land/auto launch button and a tone will sound from the remote. Make sure your throttle stick is in the down position.• After the tone is heard, move the throttle stick up until the drone starts to rise. (If throttle is not matched in 5 seconds then manual flight will be cancelled.)TOGGLE INTO AUTO HOVER WHILE IN MANUAL FLIGHT• Press either the up or down altitude locking button totoggle back into auto hover. (Your drone will hover at thecurrent throttle.)TOGGLE INTO MANUAL FLIGHT BEFORE TAKE-OFF• Hold stunt button and press auto land/auto launch button and a tone will sound from the remote. Make sure your throttle stick is in the down position. • Push the throttle stick up to begin manual flight.FLIGHT CONTROLSDIRECTION STICK• Push the direction stick forward to fly forward oraway from you (Green blade in front). Pushbackwards to fly backward. The further you push,the faster the drone will fly in that direction.• Push the direction stick left to fly left. Push right to fly right. The further you push, the faster the drone will fly sideways.FLIGHT SENSITIVITY SWITCHThe Drone’s responsiveness may be adjusted on the Controller to match your flying skills. There are three choices: 1 LOW sensitivity 2 HIGH sensitivity It is best to start in the low sensitivity position until you have mastered flying. Flight sensitivity can be adjusted before or during flight.THROTTLE/ROTATION STICKPress up tofly forwardPress down to fly backwardPress leftto fly leftPress right to fly rightDIRECTION STICKPress upto liftPress downto descendPress left to rotate counter-clockwisePress right to rotate clockwiseNANO DRONEONOFFStunt ButtonRotation Trim Left/Right TrimForward/Backward TrimPower On/off Switch/sensitivity SwitchPower indicator LEDTHROTTLE/ROTATION STICK• While in manual flight mode push the throttle stick forward to make drone lift.• The further you push the throttle stick, the faster you lift. Up and down controls only apply to manual flight mode. ((ALTITUDE BUTTONS• Press the up or down arrow to adjust the drone’s altitude. The drone will lift or lower approximately 12” each time the up or down arrow is pressed.(Distance may vary.)• Hold the up or down buttons for continuous lift or descent.AUTO LAUNCH/LAND BUTTON• Press the auto launch button to launch a few feet from the ground. (Exact height may vary.)• Press the auto land button to land the drone by itself.• When launching the drone, face the samedirection as the drone. Green blades and greenLEDs should be in front.• If your drone drifts in any direction when you arehovering, you will need to make Trimadjustments to correct the driving. Trimadjustments are sometimes needed when thedrone is first flown after purchase. See TRIMADJUSTMENTS section for details.• Practice launching, hovering and landing beforeattempting to learn other moves.• Flying 2 to 3 feet above the ground will reduceground turbulence and make flying easier.• When first attempting to fly in differentdirections, start by tapping the direction stickuntil you have a feel for it. Always move controlsslowly until you become comfortable operatingthe drone.• Once you’ve mastered flying in directions,practice rotational controls. Spinning andkeeping drone facing the same direction as youmakes flying easier and more intuitive.• Stay 2 to 3 feet away from walls and ceilingsas drone will be drawn towards them if you flytoo close.• If propeller blades come in contact withanother object or you crash, throttle down orauto land immediately to prevent possible orfurther damage.• If anything prevents drone’s blades fromspinning or they become jammed, throttledown or auto land immediately. Do not attemptto fly until obstruction has been removed anddamage fixed.• Should something prevent drone’s blades fromspinning, drone may auto shutdown. LiPobattery will need to be unplugged thenreconnected to restore flying power.• If the drone flies too far away, beyond thecontrol range of the remote, the drone willauto-land to prevent the drone from flying awayout of control.01598
3 x1.5 V AAA (LR03)+ AAA/LR03/R03 1.5V –+ AAA/LR03/R03 1.5V –– AAA/LR03/R03 1.5V +®If the drone drifts in any direction while hovering (and you are not pressing the direction stick), you may need to make trim adjustments. Press the recommended trim button as described below to make adjustments.Tip 1: When the remote LED flashes 3 times quickly, the trim will revert back to middle of trim range.Tip 2: If you are uncomfortable trimming the drone in flight, you can land onto a flat surface and make your trim adjustments. NOTE:Trim adjustments will remain saved until remotes batteries are removed. ONE TOUCH STUNTSTRIM ADJUSTMENTS BARREL ROLLWhile flying forward (or reverse), tap the stunt button.NOTE: Once a stunt has been initiated, DO NOT adjust Throttle or press any other controls until the stunt has been completed.CAUTION!The drone should be flying at least 6 feet in the air with a minimum clearance of 6 feet in all directions before attempting stunt functions.FLIP1 Bring the drone to a mid-air hover without flying in any direction. Remove finger from the direction stick. 2 While hovering, tap and hold the stunt button. 3 Then quickly tap the direction stick in the direction you want the drone to flip.Before each use, an adult should check this product and the LiPo battery to ensure no damage or hazards exist. Drone has rotating blades that move at high speed, posing danger of damage and injury. Pilots are responsible for any actions that result in damage or injury from the improper operation of drone. Adequate flying space is required. Avoid flying near interior fans and/or vents as they may make flying difficult to control. Keep a safe distance away from streets, public thoroughfares and power lines. Never attempt to retrieve drone from any location higher than your reach (such as rooftops or trees) or from any location that poses a safety hazard. Never fly drone at night. Keep drone in sight at all times during operation. Discontinue operation immediately if drone flies out of your field of view. Do not fly near spectators or animals. Pets can become excited about R/C vehicles therefore keep away from pets at all times. Keep spinning rotors away from fingers, hair, eyes and other body parts. Always launch from a flat surface. Never leave drone unattended while it is turned on. Read all enclosed information before operating.If the drone drifts forward – Press B button If the drone drifts backwards – Press F button If the drone drifts left – Press R button If the drone drifts right– Press L button If the drone spins counter-clockwise, when viewed from the top – Press button If the drone spins clockwise,when viewed from the top – Press button ADULT SUPERVISION REQUIRED1 Turn drone off. Connect charging cord to plug on drome. 2 Plug charging cord into computer or USB power block. 3 Red light = chargingGreen light = fully chargedCHARGING PRECAUTIONS:• After use, allow drone (battery on bottom) to cool down to room temperature before charging again.• Charge drone in an isolated area, away from excessive heat or moisture.• If you suspect that the battery is damaged or swelling, turn off the drone immediately.• Do not modify, heat, or wet the battery in any way. Only recharge with provided charger.• Nano Drone• USB Charging Cable• Remote Control• 4 Replacement BladesCONTENTS REMOTE BATTERIESCHARGING THE DRONELoosen the screw in the Remote Control battery compartment door with a Phillips screwdriver and insert batteries as shown. Replace door and tighten screw.THIS PRODUCT CONTAINS A LITHIUM-POLYMER BATTERY 3.7V 100mAh:LiPo batteries have a severe risk of fire and injury if they are improperly handled or misused. They may explode, overheat or ignite. Read all following precautions and instructions regarding the care and use of LiPo batteries. The built-in LiPo battery is only to be used with the drone and charger included with this product. • Keep away from flammable materials.• Do not expose to direct sunlight.• Do not place in fires or leave in hot places.• Do not drop or make subject to strong impact.• Keep dry and away from water.LiPo Battery Disposal: LiPo batteries must be recycled or disposed of properly. They should not be disposed of with other household waste. Check your local laws and regulations for correct ALKALINE BATTERY CAUTIONS• Do not use rechargeable batteries.• Different types of batteries or new and old batteries are not to be mixed.• Batteries are to be inserted using correct polarity.WARNING: Batteries are harmful if swallowed. Please keep away from children.Battery Disposal: Dispose of batteries according to the local laws and regulations of your region. Some batteries may be recycled, and may be accepted for disposal at your local recycling centre. If you are not able to identify the applicable rules in your area, please check the instructions of the battery manufacturer.recycling and/or battery disposal. ©2016 Skyrocket Toys LLC, Los Angeles CA 90066 USA. All Rights Reserved. Sky Viper and Skyrocket and their respective logos are trademarks and/or registered trademarks of Skyrocket Toys LLC. All other trademarks, logos and copyrights are the property of their respective owners, and there is no relationship express or implied with Skyrocket Toys LLC.Remove all packaging attachments before giving the toy to a child.Not suitable for children under 3 years due to small parts that could be swallowed. Conforms to product safety standards ASTM F963. Keep instructions for future reference. Do not discard. This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help.Charging cord Plug in USB cableTurn on drone.• Remove exhausted batteries as soon as possible and discard properly.• Remove all batteries from the compartment if toy is not used for a long period.• The supply terminals are not to be short circuited.• Never throw batteries in a fire or attempt to open outer casing.• Remove exhausted batteries as soon as possible and discard properly.• Remove all batteries from compartment if toy is not used for a long period.• Never throw batteries in a fire or attempt to open the outer casing.TROUBLESHOOTING• Drone’s blade may have been installed incorrectly. Reinstall and remember that the GREEN blades point forward. • Adjust the trim controls until drifting ceases.• Ensure that drone is flying a minimum distance of 6 feet from the ground with a minimum 6 feet clearance in all directions.Drone is unresponsiveAll blades spin, but drone will not fly properly or crashes immediatelyDrone crashes when attempting stunt functionsPROBLEM SOLUTIONDrone drifts in any direction during flight without direction from the remote• Ensure the remote has fresh batteries and the LiPo battery is fully charged.• Drone may be miscalibrated by launching from an un-level surface. Turn the remote off. Turn off the drone then turn them back on and try again from a flat, level launching surface.• Inspect drone for any possible damage. ONOFFONOFFMADE IN CHINAThe software included in this product contains copyrighted software that is licensed under the GPLv3. A copy of that license is included in our website at the URL below. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product and/or spare parts therefor, which will be no earlier than 05-01-2019, on our website at http://www.skyrockettoys.com/GPL/

Navigation menu