Skyrocket Toys 01599TX24G Sky Viper Stunt Drone-Remote User Manual 01599 ENF16 SVStunt IM 5 04 16

Skyrocket Toys LLC Sky Viper Stunt Drone-Remote 01599 ENF16 SVStunt IM 5 04 16

User manual

Download: Skyrocket Toys 01599TX24G Sky Viper Stunt Drone-Remote User Manual 01599 ENF16 SVStunt IM 5 04 16
Mirror Download [FCC.gov]Skyrocket Toys 01599TX24G Sky Viper Stunt Drone-Remote User Manual 01599 ENF16 SVStunt IM 5 04 16
Document ID3021282
Application IDXUflWT5EUCigUUADPAh6fA==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize140.39kB (1754936 bits)
Date Submitted2016-06-08 00:00:00
Date Available2016-06-08 00:00:00
Creation Date2016-05-04 17:23:42
Producing SoftwareAdobe PDF library 10.01
Document Lastmod2016-06-03 14:10:04
Document Title01599_ENF16_SVStunt_IM_5_04_16
Document CreatorAdobe Illustrator CS6 (Macintosh)

FLYING GUIDE
01599
STUNT DRONE
POWERING UP AND PAIRING (WITH ALTITUDE ON)
Connect battery wires on bottom of drone.
Place drone on flat surface.
Turn on remote.
Wait for flashing green light to turn solid.
FLYING BASICS
TOGGLE INTO MANUAL FLIGHT BEFORE TAKE-OFF
• Hold stunt button and press auto land/auto launch button
and a tone will sound from the remote. Make sure your
throttle stick is in the down position.
• Push the throttle stick up to begin manual flight.
Press Auto Launch to launch a few feet off the ground.
TOGGLE INTO MANUAL FLIGHT WHILE IN AUTO-HOVER
• Hold stunt button and press auto land/auto launch button
and a tone will sound from the remote. Make sure your
throttle stick is in the down position.
• After the tone is heard, move the throttle stick up until
the drone starts to rise. (If throttle is not matched in
5 seconds then manual flight will be cancelled.)
Press the Altitude button to fly 12” higher or lower.
TOGGLE INTO AUTO HOVER WHILE IN MANUAL FLIGHT
• Press either the up or down altitude locking button to
toggle back into auto hover. (Your drone will hover at the
current throttle speed.)
Press the directional Thumbstick to fly in any direction.
Press the Auto Land button to land.
FLYING TIPS
FLIGHT CONTROLS
Press up
to lift
THROTTLE/ROTATION STICK
• While in manual flight mode push the throttle
stick forward to make drone lift.
• The further you push the throttle stick, the
faster you lift.
Up and down controls only apply to manual
flight mode.
DIRECTION STICK
• Push the direction stick forward to fly forward or
away from you (Green blade in front). Push
backwards to fly backward. The further you push,
the faster the drone will fly in that direction.
• Push the direction stick left to fly left. Push right
to fly right. The further you push, the faster
the drone will fly sideways.
THROTTLE/
ROTATION STICK
Press left
to rotate
counterclockwise
•
If your drone drifts in any direction when you are
hovering, you will need to make Trim
adjustments to correct the driving. Trim
adjustments are sometimes needed when the
drone is first flown after purchase. See TRIM
ADJUSTMENTS section for details.
•
Practice launching, hovering and landing before
attempting to learn other moves.
•
Press down
to fly
backward
Flying 2 to 3 feet above the ground will reduce
ground turbulence and make flying easier.
•
When first attempting to fly in different
directions, start by tapping the direction stick
until you have a feel for it. Always move controls
slowly until you become comfortable operating
the drone.
Press left
to fly left
•
Once you’ve mastered flying in directions,
practice rotational controls. Spinning and
keeping drone facing the same direction as you
make flying easier and more intuitive.
•
Stay 2 to 3 feet away from walls and ceilings
as drone will be drawn towards them if you fly
too close.
•
If propeller blades come in contact with
another object or you crash, throttle down or
auto land immediately to prevent possible or
further damage.
•
If anything prevents drone’s blades from
spinning or they become jammed, throttle
down or auto land immediately. Do not attempt
to fly until obstruction has been removed and
damage fixed.
•
Should something prevent drone’s blades from
spinning, drone may auto shutdown. LiPo
battery will need to be unplugged then
reconnected to restore flying power.
•
If the drone flies too far away, beyond the
control range of the remote, the drone will
auto-land to prevent the drone from flying away
out of control.
Power Indicator LED
Press down
to descend
When launching the drone, face the same
direction as the drone. Green blades and green
LEDs should be in front.
Press up to
fly forward
Forward/
Backward Trim
Stunt Button
•
DIRECTION STICK
Rotation Trim
Power On/
Off Switch
Left/Right Trim
Press right
to rotate
clockwise
Press right
to fly right
ALTITUDE BUTTONS
• Press the up or down arrow to adjust
the drone’s altitude. The drone will lift
or lower approximately 12” each time
the up or down arrow is pressed.
(Distance may vary.)
• Hold the up or down buttons for
continuous lift or descent.
AUTO LAUNCH/LAND BUTTON
• Press the auto launch
button to launch a few feet
from the ground.
(Exact height may vary.)
• Press the auto land button
to land the drone by itself.
FLIGHT SENSITIVITY SWITCH
The Drone’s responsiveness may be adjusted on the controller to match your flying skills.
There are three options: 1 LOW sensitivity 2 MEDIUM sensitivity 3 HIGH sensitivity
It is best to start in the low sensitivity position until you have mastered flying. Flight sensitivity
can be adjusted before or during flight.
LOW
MED
12 3
HIGH
12 3
12 3
Online Video
Instructions & Flying
Tips available now at
SKYVIPER.COM
TRIM ADJUSTMENTS
ONE TOUCH STUNTS
If the drone drifts in any direction while hovering (and you are not pressing the
direction stick), you may need to make trim adjustments.
Press the recommended trim button as described below to make adjustments.
Tip 1: When the remote LED flashes 3 times quickly, the trim will revert back to middle of trim range.
Tip 2: If you are uncomfortable trimming the drone in flight, you can land onto a flat surface and make
your trim adjustments.
If the drone drifts forward
– Press B button
If the drone drifts backwards
– Press F button
If the drone drifts left
– Press R button
NOTE:
BARREL ROLL
While flying forward (or reverse), Once a stunt has been initiated, DO NOT adjust Throttle or press
any other controls until the stunt has been completed.
tap the stunt button.
FLIP
1 Bring the drone to a mid-air
hover without flying in any
direction. Remove finger
from the direction stick.
2 While hovering, tap and
hold the stunt button.
3 Then quickly tap the
direction stick in the
direction you want the
drone to flip.
CAUTION!
The drone should be flying at least 6 feet in the air with a minimum clearance of 6 feet in all directions
before attempting stunt functions.
If the drone drifts right
– Press L button
If the drone spins counter-clockwise,
when viewed from the top
– Press
button
If the drone spins clockwise,
when viewed from the top
– Press
button
TROUBLESHOOTING
PROBLEM
SOLUTION
MORE STUNTS!
Drone drifts in any
direction during flight
without direction from
the remote
•
Adjust the trim controls until drifting ceases.
For flying tips and instructions on how to perform more
one-touch stunts, please visit www.skyviper.com
All blades spin, but drone
will not fly properly or
crashes immediately
•
Drone’s blade may have been installed incorrectly. Reinstall and
remember that the GREEN blades point forward.
FOR BETTER STUNT PERFORMANCE
•
Drone is
unresponsive
•
•
Drone crashes when
attempting stunt
functions
•
Ensure the remote has fresh batteries and the LiPo battery is
fully charged.
Drone may be miscalibrated by launching from an un-level surface. Turn
the remote off. Turn off the drone then turn them back on and try again
from a flat, level launching surface.
Inspect drone for any possible damage.
Ensure that drone is flying a minimum distance of 6 feet from the
ground with a minimum 6 feet clearance in all directions.
ADULT SUPERVISION REQUIRED
Before each use, an adult should check this product and the LiPo battery to ensure no damage or
hazards exist. Drone has rotating blades that move at high speed, posing danger of damage and
injury. Pilots are responsible for any actions that result in damage or injury from the improper
operation of drone. Adequate flying space is required. Avoid flying near interior fans and/or vents as
they may make flying difficult to control. Keep a safe distance away from streets, public thoroughfares and power lines. Never attempt to retrieve drone from any location higher than your reach
(such as rooftops or trees) or from any location that poses a safety hazard. Never fly drone at night.
Keep drone in sight at all times during operation. Discontinue operation immediately if drone flies out
of your field of view. Do not fly near spectators or animals. Keep spinning rotors away from fingers,
hair, eyes and other body parts. Always launch from a flat surface. Never leave drone unattended
while it is turned on. Read all enclosed information before operating.
Blade guards are great for beginners and are highly recommended
when first learning how to fly a drone. Blade guards add weight and
reduce the drone’s agility. For maximum flight and stunt
performance, blade guards should be removed. When flying in Flight
Sensitivity Mode 3, blade guards should be removed.
SKY VIPER FLIGHT SIMULATOR
BATTERY REPLACEMENT
Learn and practice maneuvers on your phone,
then apply your new skills in real life. Download the app for free!
- Auto & Manual Flight Modes
- Practice & Challenge Simulations
- 1st and 3rd Person Views
- Choose from the entire Sky Viper fleet
Double your flying time with a 2nd battery!
Details of how to purchase additional or
replacement battery packs available at
SKYVIPER.COM
THIS PRODUCT CONTAINS A LITHIUM-POLYMER BATTERY 3.7V 350mAh:
LiPo batteries have a severe risk of fire and injury if they are improperly handled or misused. They may
explode, overheat or ignite. Read all following precautions and instructions regarding the care and use
of LiPo batteries.
The built-in LiPo battery is only to be used with the drone and charger included with this product.
• Keep away from flammable materials.
• Do not expose to direct sunlight.
• Do not place in fires or leave in hot places.
• Do not drop or make subject to strong impact.
• Keep dry and away from water.
• Remove exhausted batteries as soon as possible and discard properly.
• Remove all batteries from the compartment if toy is not used for a long period.
• The supply terminals are not to be short circuited.
• Never throw batteries in a fire or attempt to open outer casing.
LiPo Battery Disposal: LiPo batteries must be recycled or disposed of properly. They should not be
disposed of with other household waste. Check your local laws and regulations for correct recycling
and/or battery disposal.
ALKALINE BATTERY CAUTIONS
• Do not use rechargeable batteries.
• Different types of batteries or new and old batteries are not to be mixed.
• Batteries are to be inserted using correct polarity.
• Remove exhausted batteries as soon as possible and discard properly.
• Remove all batteries from compartment if toy is not used for a long period.
• Never throw batteries in a fire or attempt to open the outer casing.
WARNING: Batteries are harmful if swallowed. Please keep away from children.
Battery Disposal: Dispose of batteries according to the local laws and regulations of your region. Some
batteries may be recycled, and may be accepted for disposal at your local recycling center. If you are not able
to identify the applicable rules in your area, please check the instructions of the battery manufacturer.
This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected - Consult the dealer or an experienced
radio/TV technician for help.
Remove all packaging attachments before giving the toy to a child.
Not suitable for children under 3 years due to small parts that could be swallowed.
Conforms to product safety standards ASTM F963.
Keep instructions for future reference. Do not discard.
©2016 Skyrocket Toys LLC, Los Angeles CA 90066 USA. All Rights Reserved. Sky
Viper and Skyrocket and their respective logos are trademarks and/or
registered trademarks of Skyrocket Toys LLC. All other trademarks, logos and
copyrights are the property of their respective owners, and there is no
relationship express or implied with Skyrocket Toys LLC.
MADE IN CHINA.
®
The software included in this product contains copyrighted software that is licensed under the GPLv3. A copy of that license is included in our
website at the URL below. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment
of this product and/or spare parts therefor, which will be no earlier than 05-01-2019, on our website at http://www.skyrockettoys.com/GPL/
BATTERIES AND MAINTENANCE
S1700
STUNT DRONE
CONTENTS
REMOTE BATTERIES
• RC Stunt Drone
• Rechargeable 3.7v 350mAH LiPo Battery
• Screwdriver
• Remote Control
• Screws
• 4 Replacement Blades
• USB Charging Cable
• Alternative Pro Thumbsticks
Loosen the screw in
the Remote Control
battery compartment
door with a Phillips
screwdriver and insert
batteries as shown.
Replace door and
tighten screw.
– AAA/LR03/R03 1.5V +
+ AAA/LR03/R03 1.5V –
+ AAA/LR03/R03 1.5V –
3 x1.5 V AAA (LR03)
CHARGING THE DRONE
1 Disconnect battery wires. Push down the battery
2 Plug charging cord into computer or USB
box holder on the rear side of the drone. Pull battery
power block. Once charged, disconnect
box out of underside of drone.
battery from USB charging cable.
3 Insert LiPo battery into back of drone.
Reconnect the battery wires.
LiPo BATTERY
Disconnect battery wires
Push down
Pull battery box out
CHARGING PRECAUTIONS:
• After use, allow drone (battery on bottom) to cool down to room
temperature before charging again.
• Charge drone in an isolated area, away from excessive heat
or moisture.
•
•
ALTERNATIVE
PRO THUMBSICKS
1 Unplug battery on drone.
3 Remove the small screw using the mini
screwdriver provided.
2 Make note of the blade color and letter
(A or B) before removing the blade
4 Replace the damaged blade with a new
from Drone. (Markings are located on
blade with matching color and letter.
the underside of blades and Drone).
Secure the blade with the retaining screw.
Bottom View of Drone
GREEN
BLADES
FRONT
Plug into charging wire
If you suspect that the battery is damaged or swelling, turn off the
drone immediately.
Do not modify, heat, or wet the battery in any way. Only recharge with
provided charger.
REPAIRING DAMAGED BLADES
Plug in USB cable
Red light = charging
Green light = fully charged
BACK
BLACK
BLADES
MAINTENANCE
• Over time, loose hair or carpet fibers may get wound in blades, reducing
performance. Unplug the Drone and remove fibers from motors. (Remove
blades if necessary)
•
•
Lift joystick upward to remove.
Insert thumbstick into stem to replace.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Format                          : application/pdf
Title                           : 01599_ENF16_SVStunt_IM_5_04_16
Metadata Date                   : 2016:06:03 14:10:04+08:00
Modify Date                     : 2016:06:03 14:10:04+08:00
Create Date                     : 2016:05:04 17:23:42-07:00
Creator Tool                    : Adobe Illustrator CS6 (Macintosh)
Thumbnail Width                 : 256
Thumbnail Height                : 116
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 13690 bytes, use -b option to extract)
Instance ID                     : uuid:e0ae4309-bb76-4d2a-ab92-d41b2fb7c8b9
Document ID                     : xmp.did:66353EA43920681183D1A858E3736B30
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:65353EA43920681183D1A858E3736B30
Derived From Document ID        : xmp.did:65353EA43920681183D1A858E3736B30
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:FB7F11740720681183D1F7CD751CB142, xmp.iid:66353EA43920681183D1A858E3736B30
History When                    : 2016:04:14 19:01:43-07:00, 2016:05:04 17:23:21-07:00
History Software Agent          : Adobe Illustrator CS6 (Macintosh), Adobe Illustrator CS6 (Macintosh)
History Changed                 : /, /
Manifest Link Form              : EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference
Manifest Reference File Path    : /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone front.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone front.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone bottom.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/streaming_Front_Prop_off.png, /Users/noodle/Desktop/Joystick.png, /Users/noodle/Desktop/Thumbstick.png, /Users/noodle/Desktop/Empty.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/streaming_Controler_gry.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/streaming_Controler_gry.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/streaming_Controler_gry.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Top_View.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Top_View.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Top_View.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/streaming_Controler_gry.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/streaming_Controler_gry.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/streaming_Controler_gry.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone front.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone top.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Top_View.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Top_View.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Top_View.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Battery Cross Sell_GREY.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone bottom.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/battery out.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Google logo_BW.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/iphone_6_BW.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Straight Streaming.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Straight Streaming.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Straight Streaming.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone bottom.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/battery in.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone front.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone front.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone front.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone front.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/remote controller back.png
Startup Profile                 : Print
Has Visible Overprint           : True
Has Visible Transparency        : True
N Pages                         : 1
Max Page Size W                 : 11.692919
Max Page Size H                 : 16.535414
Max Page Size Unit              : Inches
Font Name                       : EurostileRegular, EurostileBold, Myriad-Roman, EurostileLTStd-Ex2, EurostileLTStd-BoldEx2, PirulenRg-Regular
Font Family                     : Eurostile, Eurostile, Myriad, EurostileLTStd Ex2, EurostileLTStd BoldEx2, PirulenRg Regular
Font Face                       : Regular, Bold, Roman, Ex2, BoldEx2, Regular
Font Type                       : Open Type, Open Type, Type 1, Open Type, Open Type, Unknown
Font Version                    : Version 1.51, Version 1.51, 001.001, OTF 1.029;PS 001.003;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.029;PS 001.003;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.006;PS 001.000;Core 1.0.23;hotunix 1.28
Font Composite                  : False, False, False, False, False, False
Font File Name                  : Eurostile, Eurostile, MyriaRom; Myriad, EurostileLTStd-Ex2.otf, EurostileLTStd-BoldEx2.otf, MyriadPro-Regular.otf
Plate Names                     : PANTONE 294 C copy, Deleted Global Color, PANTONE 294 C 2
Swatch Groups Colorants L       : 18.823500
Swatch Groups Colorants A       : 4
Swatch Groups Colorants B       : -43
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Group Name        : Brights
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: CMYK Yellow
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 0.000000
Swatch Groups Colorants Magenta : 0.000000
Swatch Groups Colorants Yellow  : 100.000000
Swatch Groups Colorants Black   : 0.000000
Producer                        : Adobe PDF library 10.01
Slug Family                     : Myriad
Slug Version                    : 001.000
Slug Outline File Size          : 31315
Slug Kerning Checksum           : 418590
Slug Foundry                    : Adobe Systems
Slug Font Kind                  : PostScript
Slug Checksum                   : 2245842652
Slug Post Script Name           : Myriad-Roman
Slug Font Sense 12 Checksum     : 2245842652
Page Count                      : 4
Creator                         : Adobe Illustrator CS6 (Macintosh)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: O5301599TX24G

Navigation menu