Skytech II 1003TX Remote Control Transmitter User Manual

Skytech II, Inc. Remote Control Transmitter 1

a href="https://usermanual.wiki/Skytech-II" itemprop="url"> Skytech II >

User Manual

SKYTECH 1001SR/P TH REV. 09/02 Page 1 of 6 1001SR/P TH INSTALLATION AND OPERATING INSTRUCTIONS MULIT-FUNCTION WIRELESS REMOTE CONTROL SYSTEM FOR OPERATING SERVO MOTORS VALVES OR PULSE SOLENOIDS VALVES INTRODUCTION This remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas heating appliances. The system is operated manually from the transmitter. The system operates on radio frequencies (RF) within a 20' range using non-directional signals. The system operates on one of 255 security codes that are programmed into the transmitter at the factory; the remote receiver's code must be matched to that of the transmitter prior to initial use. Review THERMO SAFETY SECTION under RECEIVER section. This high temperature safety feature shuts down the appliance when a potentially unsafe condition exists. TRANSMITTER This remote control SYSTEM offers the user a battery-operated remote control to power up to a 6 VDC servo motor or solenoid such as those used with gas valves used in some heater rated gas logs, gas fireplaces and other gas heating appliances. The servo motor or solenoid circuit uses the battery power from the receiver to operate a servo motor or solenoid. The circuit has reversing polarity software which reverses the positive (+) and negative (-) output of the receiver's battery power to drive the servo motor or solenoid forward/backward (HI/LO FLAME) or open/close (FLAME SOLENOID - ON/OFF). The SYSTEM is controlled by the remote transmitter. The transmitter operates on a (2) 1.5V AAA batteries made specifically for remote controls and electronic lighters. Before using the transmitter, remove the insulation tab protecting one end of the battery in the battery compartment. It is recommended that ALKALINE batteries always be used for longer battery life and maximum operational performance. KEY SETINGS • ON/HI -Operates unit to on position. • LO/OFF - Operates unit to off position • MODE - Changes unit from manual feature to thermo feature. • SET - Sets temperature in thermo in feature. 1. DISPLAY Indicates CURRENT room temperature . 2. 0 F OR 0 C Indicates degrees Fahrenheit or Celsius. 3. FLAME Indicates burner/valve in operation. 4. ROOM Indicates remote is in THERMO operation. 5. TEMP Appears during manual operation. 6. SET Appears d uring time the of setting the desired temperature in the thermo operation. ON/HIMODELO/OFFBUTTONWALL CLIPSLOT12VBATTERYCOMPARTMENTFRONT BACKLO/OFFSETON/HIBUTTONMODEBUTTONSETBUTTON ROOMLCD - Liquid Crystal DisplayTEMP123SET456 ON/HIMODELO/OFFSET1234
SKYTECH 1001SR/P TH REV. 09/02 Page 2 of 6 SETTING 0 F / 0C SCALE The factory setting for temperature is 0 F. To change this setting to 0 C, first • Press the ON/HI key and the LO/OFF key on the transmitter at the same time this will change from 0 F to 0 C. Follow this same procedure to change from 0 C back to 0 F. MANUAL FUNCTION To operate the system in the manual mode do the following. ON OPERATION Press and hold the ON/HI key until the appliance flame comes on and reaches the desired flame height or is at full on. During this time the LCD screen will show HI, after 3 seconds the LCD screen will default to display room temperature and the word TEMP will show. OFF OPERATION Press and hold the LO/OFF key until the appliance flame reaches the desire flame height or completely shuts off. During this time the LCD screen will show LO, after 3 seconds the LCD screen will default to display room temperature and the word TEMP will show. THERMOSTAT FUNCTION SETTING DESIRED ROOM TEMPERATURE This remote control system can be thermostatically controlled when the transmitter is in the THERMO mode (SET must be displayed on the screen). To set the DESIRED room temperature, Press the MODE key the display will show the words SET TEMP and the temperature display will began to flash. Press and hold the SET key until the desired set temperature is reached then release the SET key. Press the MODE key to disengage the thermo mode. The word ROOM on the LCD screen will not show when the thermo is not in operation. NOTE: The highest SET temperature is 990 Fahrenheit (320 Celsius) and the lowest temperature (450 F, or 60 C ). TEMP TEMPSET THERMO SET SCREEN DURING ADJUSTING TO ON SCREEN DURING ADJUSTING TO OFF TEMP SCREEN AFTER 3 SECOUND DEFAULT ROOM TEMP THERMO OFF ROOM TEMP THERMO ON TEMP SCREEN AFTER 3 SECOUND DEFAULT
Download:
Mirror Download [FCC.gov]
Document ID274586
Application IDi2g4LjKE6HeeONBwzT4y7Q==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize16.12kB (201519 bits)
Date Submitted2002-10-03 00:00:00
Date Available2002-10-03 00:00:00
Creation Date2002-09-24 10:48:30
Producing SoftwareAcrobat PDFWriter 4.0Windows ª©
Document Lastmod2002-09-25 19:09:01
Document Title穨_1_.PDF
Document Creator穨Microsoft Word
Document Author: 穨hyt
FCC ID Filing: K9L1003TX

Navigation menu