Smarfid Security Equipment MG38152K Magic MINI 125 kHz Reader User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2059155
Application ID	gkvY/VG6Cxj1+kRFGVyYwg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.56kB (144515 bits)
Date Submitted	2013-08-30 00:00:00
Date Available	2013-08-30 00:00:00
Creation Date	2017-10-26 02:12:53
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-26 02:12:53
Document Title	Microsoft Word - Users Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

Keypad & Proximity Flash Mount Reader Installation Manual
Mounting:
1.
2.
Install the metal plate on the wall with two or four screws, which depends on different kinds of
Recommendation:
gang box being installed1.
1.
Linear DC Power Supply;
2.
22AWG shielded cable; it’s required to do “one-point” ground. (As shown in the diagram)
The cover shall clip on the upper edge
2 the push in the bottom part as show in
diagram3.
3.
Tighten the secure non-dropout screw, which located underneath of the reader to fix the
reader and the back plate4, installation is completed.
Specification:
Input Voltage (at
Reader end)
Operating Current
Operating
Temperature
Power up Sequences:
DC10V~15V
160mA (max)
-30ºC~70 ºC
Typical Read
range
Maximum Cable
Length
Number pad
> 5cm
150m
Color
Label
Description
Red
+12V dc
Black
GND
Signal GND
Green
Data0
Wiegand Output data, D0
White
Data1
Wiegand Output data, D1
Yellow
RED LED
RED LED control, active low.
Blue
Green LED
Green LED control, active low
Brown
Buzzer
Buzzer input, active low
Orange
Tamper
Tamper output (open collector, Active low, max 100mA)
Power Supply to the reader
Wiring:
4 bits burst by default
format
1.
When reader is powered up, the Green back will flicker for 5 seconds. The reader will beep
Keypad & Proximity Flash Mount Reader Installation Manual
once and the reader is in Ready mode.
2.
Present the card. The Blue LED will flicker once; buzzer will beep once.
3. When card is present and read by the reader, blue back lit will flash once; and buzzer will
beep once as well. The card data will then transmit to the controller. After, weather the back lit
FCC Warning:
Any Changes or modifications not expressly approved by the party responsible for
of the reader will remain ON or Flash or change to Green or Red color, this shall depend on
the Green and Red LED inputs.
4. For number pad reader, when a number is pressed and successfully detected, the back lit
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
under the number will flash 1 time and the buzzer will beep once. The number being pressed
will burst out by default (4 bits burst).
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Troubleshooting:
Physical Dimension:
Trouble List
No Response
when Power Up
Auto Restart
Solution
correctly connected (See “Wiring” above).
Check the input voltage is sufficient (See “Specifications” above).
Check the input voltage is sufficient (See “Specifications” above).
Check the format setting on the controller if it is the same as the card
format. Use approved card (known format and Facility Code) to test.
Cannot read card
number correctly
Discount the power and confirm that the power supply cable is
Check if the shield cable is correctly connected to Classis Ground at
ONE point only.
above).
Reader beeps but
No card data info
Check if data 0 & data 1 cable is correctly connected (See “Wiring”
Check the input voltage at the card reader end is correct (See
“Specifications” above).
Buzzer error
Back Lit Error
Check if the buzzer cable is correctly connected (See “Wiring” above).
Check the Led cable is correctly connected (See “Wiring” above).
Use Default Configuration Card to set it back to normal.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Extract
Author                          : Administrator
Create Date                     : 2013:08:28 13:59:19+08:00
Modify Date                     : 2013:08:30 16:50:33-07:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Metadata Date                   : 2013:08:30 16:50:33-07:00
Format                          : application/pdf
Title                           : Microsoft Word - Users Manual
Creator                         : Administrator
Document ID                     : uuid:eba35bda-5e1d-46e7-b446-c2859a51b444
Instance ID                     : uuid:e73e834a-614b-46d6-ae8e-13622a9c542c
Page Count                      : 2

EXIF Metadata provided by EXIF.tools