Smarfid Security Equipment MH322 Magic Series 13.56MHZ&125KHZ Reader User Manual

Shanghai Smarfid Security Equipment Co, Ltd. Magic Series 13.56MHZ&125KHZ Reader

User manual

125KHz & 13.56HMz Dual Frequencies Magic Series Reader Design & Technologies Number pad use “touching sensor”, the latest technology and individual number backlit when touch. Economical Mini Magic can be mullion mount. Display Magic can provide customer a full series of choices Front plate customization and back lit design is available. Design with End User logo is possible. Support on-site Reader Configuration Card to change certain parameters. OLED Display allow user to see the message clearly under direct sunlight. Door Bell function for Number pad reader. Tamper protection Friendly Installation “Touch” number pad does not carry any moving parts, which implies more durable. All weather proof design with IP65 certificate. Universal back plate allows the reader be installed on different size of gang box. Non-drop bottom screw made servicing handier. Metal back plate allows the reader install on metal surface and back-to back without affecting the read range. All input and output signals are protected against static charges. 和输出信号受到防静电保护 Reverse power protection. 接保护 Stainless steel Security screw is an option All inputs are 12Vdc protected. Display reader can display CSN/UID number or Programmed Card Number or user Name when the user card is present.* (Supported Multiple Languages) Available Later! Standard Magic Available Later! Number pad Magic Read both low frequencies (125KHz) and high frequencies card; supported high frequency technologies are Legic, Mifare, Mifare Plus, DesFire or FuDan CPU). A PIN can be set inside the card to authenticate with the reader so that “Card + PIN” mode can be implemented without relying on the controller.*
Model Number: X1 X2 N1 N2 N3 – N4 X3 Model Functions Standard & Mini Reader Keypad Reader Display Reader Configurable Functions Re-configure Window 5 seconds (Default) or Half an hour after Power up Reader Output Format CSN/UID 32bits, 34bits, 56bits (backward/forward), file content reading for programmed ID Wiegand Plus Width Different choices to fit with different Controller’s requirements Keypad Output N/A Definable Definable Buzzer Control Reader & Controller control (Default) or Controller control only LED/Back lit Control Define different LED color response base on Green LED N/A Display Clock Synchronization. N/A N/A  H/W reset  Via RS485 TimeSyn S/W Technical Specifications Typical Read range 3 – 5 cm Reader Standard Output Wiegand (RS232 & RS485 optional) Standard Keypad output N/A Wiegand with 4 bits burst Wiegand with 4 bits burst Display N/A N/A OLED Display Display Message N/A N/A  Access Granted, Access Denied, Enter PIN;  Time;  Card Number Wiring Distance 150m (22 AWG with shielded cable) 120m (22 AWG with shielded cable) Operating Specification: Operating Voltage 10 - 15VDC Operating Current 150mA (max) Operating Temperature -30℃-70℃ Exterior dimension (Mini) 115.5*84.5*20.5mm (84.05*54.05*16.5mm) Case material PC+ABS Standard Color Black Operating Humidity 10% - 90% Weight (Mini) 210g (160g) RF Technologies Reader Appearance and Function X1X2 HM = Mifare & 125KHz Technologies HL = Legic & 125KHz Technologies N1 3 = Normal Reader ; 5 = Display Reader N2 2 = Normal Size 8 = Mini Size N3 2 = Read UID / Card Number 3 = Read Sector (Mifare) / Segment (Legic) N4 3 = Terminal (for Display Reader) 8 = Pigtail X3 N = No Number pad; K = Number pad
FCC Caution.§ 15.19 Labelling requirements.This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that maycause undesired operation.§ 15.21 Information to user.Any Changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.§ 15.105 Information to the user.Note: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.-Consult the dealer or an experienced radio/TV technician for help.

Navigation menu