Smarfid Security Equipment REX2140433M Contactless Door Egress Device User Manual

Shanghai Smarfid Security Equipment Co., Ltd. Contactless Door Egress Device

User Manual

Contactless Door Egress Device (North America Version)Match OEM reader design in order to maximize the marketing value at the door.Design PhilosophyCapacitance Proximity Technology has been used instead of Infar-red technology – environmentalindependent design.Back Light design.Built-in buzzerWhen triggered, the back lit will change color with an audible tone – very user friendly.Provide a dry contact output to interface with any Access Control controller.Build-in Mechanical Override in case of power failure or electronic failure.Build-in a digital timer to control the relay output timing from 1 to 63 sec..Optional with Remote Control (433MHz) to trigger the REX output remotely.Each Remote Control can “learn” up to 5 Remote Buttons.Technology & FunctionFriendly InstallationAll input and output signals areprotected against staticcharges.Reverse power protection.All inputs are 12Vdc protected.Fit with US single gang box
Specification:ModelFunctionsREX2140-cFunctional SpecificationRequest to ExitindicationColor changes from Blue to Green with a beepRequest to Exit outputDry contact outputREX RelayNC/NO jumper selectable rated @ 30Vdc; 1AMechanical OverrideAvailableOutput TimerFrom 1 sec to 63 secRemote Button(Optional)433MHz(Max supports 5 remote buttons at the same time.)Dimension118.2 (L) X 74.2 (W) X 8.5 (H) mm (above surface)Technical SpecificationsTypical Read range~2.5 cmElectric Gang BoxRequirementShall fit with most of the North America single gang box installationWeight157gOperating Specification:Operating Voltage10 - 15VDCCase materialPC+ABSOperating Current150mA (max @ 12Vdc)Standard ColorBlack & WhiteOperating Temperature0℃-60℃Operating Humidity10% - 90%
FCC Caution.§ 15.19 Labelling requirements.This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that maycause undesired operation.§ 15.21 Information to user.Any Changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.§ 15.105 Information to the user.Note: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.-Consult the dealer or an experienced radio/TV technician for help.
Version 1.0 15JUN2016 REX2-c Installation and Operation Manual REX2 (US Gang Box version) is a contactless proximity exit button. It is using capacitive proximity technology instead of Infra-Red to realize the contactless triggering. While Infra-Red technology exit button will trigger by sunlight, air conditioner or even a paper…etc, capacitive proximity technology does not have such problems. This makes REX2 a very ideal product for applications which requires a high hygiene requirement standard. Function:  Put your hand near the exit button then you will trigger the device. The color of the exit button will change to green when triggered. At the same time, the relay inside the exit button device will trigger for 1 second, and the buzzer will beep once.  To adjust the door open duration, please power off the exit button. Change the DIP Switch setting to alter the door open duration from 1 to 63 seconds, and then power it up again.  Support manually door open  Support remote controlled door open PCB setting description: FT Function switch RC Function switch For door open duration setting from 1 to 63 seconds.
Version 1.0 15JUN2016 Wiring DIP Switch Setting: 1 ON 1 No.1,2,4,8,16,32 are used for adjusting door open duration ON = valid OFF =invalid Door open duration=To add all the ON position switch numbers Example: If we set #1 and #8 to “ON”, the door open during will be: 1+0+0+8+0+0=9, the decimal number is 9 seconds ( decimal number) *Setting all DIP Switch to OFF position means door open duration=1sec. OFF 0 2 ON 2 OFF 0 4 ON 4 OFF 0 8 ON 8 OFF 0 16 ON 16 OFF 0 32 ON 32 OFF 0 RC ON RC ON In certain installation environments, when the device’s maximum capacitive value is reached, setting RC to the ON position can reset the baseline of measured capacitive by offsetting a pre-programmed value to return it to a normalized triggering status. OFF RC OFF FT ON FT ON When FT is set to the ON position. a higher triggering threshold value will be adopted to prevent false trigger OFF FT OFF Installation:1) Confirm if the size of installation box fits for the REX2 as shown in Fig.1 2) Confirm all wirings are in the correct position, then set the jumpers to the right position 3) Put the whole module into the installation box and fixed by screw as Fig.2. 4) There are 2 M-type buckles at the bottom of the cover as shown in Fig.3. Buckle them into the slot at the bottom of the module and push the upper part of the cover up as Fig.4 Label Description +12V Power Input (+12VDC) RTE_COM Exit Button Output (Dry Contact) RTE_NO RTE_NC MO Manual Open Input，Active Low GND Signal Ground (0 VDC) Fig.1 Fig.4 Fig.3 Fig.2 M-type Buckles
Version 1.0 15JUN2016 baseline value Setting RC to the ON position can adjust the baseline value downward to return it to a normalized triggering status Setting FT to the ON position can adjust the triggering threshold value upward to prevent false trigger Normal triggering waveform FT OFF triggering threshold value FT ON triggering threshold value baseline value

Navigation menu