Smarfid Security Equipment VITTO Card Reader User Manual

Shanghai Smarfid Security Equipment Co, Ltd. Card Reader Users Manual

Users Manual

Keypad & Proximity Flash Mount Reader Installation Manual Mounting: 1. Install the metal plate on the wall with two or four screws, which depends on different kinds of gang box being installed1. 2. The cover shall clip on the upper edge 2 the push in the bottom part as show in diagram3. 3. Tighten the secure non-dropout screw, which located underneath of the reader to fix the reader and the back plate4, installation is completed. Specification: Recommendation: 1. Linear DC Power Supply; 2. 22AWG shielded cable; it’s required to do “one-point” ground. (As shown in the diagram) Wiring: Input Voltage (at Reader end) DC10V~15V Typical Read range > 5cm Operating Current 160mA (max) Maximum Cable Length 150m Operating Temperature -30ºC~70 ºC Number pad format 4 bits burst by defaultColor Label Description Red +12V dc Power Supply to the reader Black GND Signal GND Green Data0 Wiegand Output data, D0 White Data1 Wiegand Output data, D1 Yellow RED LED RED LED control, active low. Blue Green LED Green LED control, active low Brown Buzzer Buzzer input, active low Grey Tamper Tamper output (open collector, Active low, max 100mA) Purple Doorbell Door bell output (open collector, +5Vdc output ≤ 5mA)
Keypad & Proximity Flash Mount Reader Installation Manual Power up Sequences: 1. When reader is powered up, the Green back will flicker for 5 seconds. The reader will beep once and the reader is in Ready mode. 2. Present the card. The Blue LED will flicker once; buzzer will beep once. 3. When card is present and read by the reader, blue back lit will flash once; and buzzer will beep once as well. The card data will then transmit to the controller. After, weather the back lit of the reader will remain ON or Flash or change to Green or Red color, this shall depend on the Green and Red LED inputs. 4. For number pad reader, when a number is pressed and successfully detected, the back lit under the number will flash 1 time and the buzzer will beep once. The number being pressed will burst out by default (4 bits burst). Physical Dimension: Troubleshooting: Trouble List Solution No Response when Power Up z Discount the power and confirm that the power supply cable is correctly connected (See “Wiring” above). z Check the input voltage is sufficient (See “Specifications” above). Auto Restart z Check the input voltage is sufficient (See “Specifications” above). Cannot read card number correctlyz Check the format setting on the controller if it is the same as the card format. Use approved card (known format and Facility Code) to test. z Check if the shield cable is correctly connected to Classis Ground at ONE point only. Reader beeps but No card data infoz Check if data 0 & data 1 cable is correctly connected (See “Wiring” above). z Check the input voltage at the card reader end is correct (See “Specifications” above). Buzzer error z Check if the buzzer cable is correctly connected (See “Wiring” above). Back Lit Error z Check the Led cable is correctly connected (See “Wiring” above). z Use Default Configuration Card to set it back to normal.
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 　 Reorient or relocate the receiving antenna. 　 Increase the separation between the equipment and receiver. 　 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 　 Consult the dealer or an experienced radio/TV technician for help.

Navigation menu