SmartAnt Telecom SAG-1020 IEEE 802.11b/g Outdoor CPE User Manual Wireless Access Point
SmartAnt Telecom Co., Ltd. IEEE 802.11b/g Outdoor CPE Wireless Access Point
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 885863 |
| Application ID | TyDJADq9SXep6sVFk6+eYg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 204.64kB (2557953 bits) |
| Date Submitted | 2008-01-04 00:00:00 |
| Date Available | 2008-01-04 00:00:00 |
| Creation Date | 2007-12-21 18:06:03 |
| Producing Software | Acrobat Distiller 7.0.5 (Windows) |
| Document Lastmod | 2008-01-03 10:03:53 |
| Document Title | Wireless Access Point |
| Document Creator | Acrobat PDFMaker 7.0.7 for Word |
| Document Author: | Eleen Lin |
802.11 b/g WLAN CPE User’s Guide FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: y Reorient or relocate the receiving antenna. y Increase the separation between the equipment and receiver. y Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. y Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. FCC Statement For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. All trademarks and brand names are the property of their respective proprietors. Specifications are subject to change without prior notification. CE Statement： Hereby, declares that this device is in compliance with the essential requirement and other relevant provisions of the R&TTE Directive 1999/5/EC. Table of Content Introduction ............................................................................................................................ 1 FEATURES ............................................................................................................................. 1 FACTORY DEFAULT SETTINGS ............................................................................................... 6 Wireless AP....................................................................................................................... 6 Hardware Connection ............................................................................................................ 7 About the Operation Modes .................................................................................................. 8 ACCESS POINT MODE ............................................................................................................ 8 WDS REPEATER MODE ......................................................................................................... 8 CLIENT MODE (INFRASTRUCTURE) ....................................................................................... 8 CLIENT MODE (AD-HOC) ...................................................................................................... 8 WDS BRIDGE MODE ............................................................................................................. 9 Configuration ........................................................................................................................ 10 LOGIN .................................................................................................................................. 10 STATUS................................................................................................................................ 11 System ............................................................................................................................. 11 Statistics.......................................................................................................................... 12 WIRELESS ............................................................................................................................ 13 Basic Settings.................................................................................................................. 13 Advanced Settings........................................................................................................... 14 Security ........................................................................................................................... 18 Access Control................................................................................................................ 20 TCP/IP ................................................................................................................................ 22 Basic ............................................................................................................................... 22 OTHER ................................................................................................................................. 24 Upgrade Firmware ......................................................................................................... 24 Save/Reload Settings....................................................................................................... 25 Password ........................................................................................................................ 27 System Log...................................................................................................................... 27 INTRODUCTION This is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet Wireless Access Point. The Wireless Access Point is equipped with two 10/100 M Auto-sensing Ethernet ports for connecting to LAN and also for cascading to next Wireless Access Point. This Access Point provides 64/128bit WEP encryption, WPA and IEEE802.1x which ensures a high level of security to protect users’ data and privacy. The MAC Address filter prevents the unauthorized MAC Addresses from accessing your Wireless LAN. Your network security is therefore double assured. The web-based management utility is provided for easy configuration that your wireless network connection is ensured to be always solid and hassle free. Features • Two LAN ports for Wireless AP cascade • Support WPA • Support AP client mode • Support WDS for bridge mode • Support data rate automatic fallback • Automatic channel selection • Client access control • Support 802.1x/Radius client with EAP-TLS, TKIP, AES encryption • Support IAPP • Adjustable Tx power, Tx rate, and SSID broadcast • Allow WEP 64/128 bit • Web interface management • Support System event log and statistics • MAC filtering (For wireless only) • Support High power • Support POE (Power Over Ethernet), which enables an Ethernet network cable to deliver both data and power • SAG-1020 series WLAN 802.11 b/g Outdoor CPE Product illustration The SAG-1020 is an all-in-one device for outdoor wireless application that includes high RF power for outdoor wireless connection. Robust and costeffective structure is an ideal solution for outdoor environment and last-mile solution. The SAG-1020 builds in high gain 12 dBi directional antenna. Moreover, it provides an option to adopt versatile external antennas in order to be flexible for different wireless scenarios. It extends wireless signal to several kilometers and supports Power-over-Ethernet which facilitates installation process and accomplish long range wireless association. SAG-1020 series WLAN 802.11 b/g Outdoor CPE FEATURES ‧Compatible with IEEE 802.11b/g standards ‧Point-to-point, point-to-multipoint wireless connectivity ‧Support Router/AP, WDS, and Client mode ‧High transmit output power 20 dBm (100 mW) ‧Built-in 12 dBi high gain directional antenna ‧Conjunction with versatile external antenna. ‧Support Point-to-Point, Point-to-Multipoint connection. ‧Wireless LAN access for all indoor and outdoor areas. ‧Power over Ethernet (PoE) support; compatible to IEEE802.3af. ‧High standard watertight (IP67) and weatherproof; Wide temperature range and robust mechanical design ‧Delivers reliable, top performance in the most demanding environments ‧Powerful security with: 64/128Bit WEP, WPA, WPA2. ‧Support IAPP ‧High speed data rate up to 54Mbps SAG-1020 series WLAN 802.11 b/g Outdoor CPE Hardware Standard Transmit Output Power Antenna Interface Channel Data Rate LED Power Supply Accessory Dimension Weight Certification Temperature Humidity Green Policy Software Operating Mode Security Management Networking IEEE 802.11 b/g IEEE 802.3af 11b CCK: 20 dBm 11g OFDM: 20 dBm Adjustable Internal 12 dBi directional antenna (SAG-1020) External N-type antenna connector (SAG-102A) LAN：1×10/100 Mbps Auto-MDIX Ethernet ports 1~11 channel (N. America) 1~14 channel (Japan) 1~13 channel (Europe ETSI) 802.11b (11 Mbps, 5.5 Mbps, 2 Mbps, 1 Mbps) 802.11g (54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12 Mbps, 9 Mbps, 6 Mbps) Power / Wireless / Ethernet AC Input: 100V~240V(50~60Hz) PoE support RJ-45 Cat-5 cable 3m (non-waterproof) Waterproof RJ-45 Cat-5 cable 30m (option) Pole and Wall mounting kits Power over Ethernet Midspan: 48V, 15.4W min L*W*H = 16 * 13.4 * 7.2 cm 424 g FCC Part 15B CE 0~55 ℃(operation) ; -20~70 ℃(storage) 5~95 % (non-condensing) ROHS compliance Router/AP WDS Client Mode 64 / 128 bit WEP encryption Support WPA / WPA2, AES-CCM, and TKIP security enhanced function Support Web-based configuration utility via Ethernet IAPP support DHCP server/client support WLAN 802.11 b/g Outdoor CPE series SAG-1020 SAG-102A 12 dBi directional antenna External N-type connector Waterproof RJ-45 connector Mounting Configuration Pole mount Wall mount Order Information: 1. SAG-1020 Outdoor CPE with internal 12 dBi directional antenna 2. SAG-102A Outdoor CPE with external N-type antenna connector (without internal antenna) 3. Option accessories: a. Cat-5 waterproof cable 30m b. Versatile external antenna: i. Omni-directional: 8 / 10 dBi ii. Directional: 9 / 12 / 14 / 18 dBi Factory Default Settings Setting Device Name SSID Channel WEP IP Address Wireless Access Point Wireless AP Default value: 802.11g-AP 11 Default value: Disabled 192.168.1.254 HARDWARE CONNECTION Note: Before you starting hardware connection, you are advised to find an appropriate location to place the Access Point. Usually, the best place for the Access Point is at the center of your wireless network, with line of straight to all your wireless stations. Also, remember to adjust the antenna; usually the higher the antenna is placed, the better will the performance be. Connection of using the included Power adapter: Connect to your local area network: connect a Ethernet cable to one of the Ethernet port of this Wireless Access Point, and the other end to a hub, switch, router, or another wireless access point. Connection of using PoE: The hardware connection is basically the same as using a power adapter to supply power to your wireless access point, except for a different power origin it gains. With PoE, your wireless access point gains power from a PSE device through simply an Ethernet UTP cable! Configure your PC: Make sure your local PC(s) has wireless network adapter installed. ABOUT THE OPERATION MODES This device provides four operational applications with Access Point, Bridge, Client (Ad-hoc) and Client (Infrastructure) modes, which are mutually exclusive. This device is shipped with configuration that is functional right out of the box. If you want to change the settings in order to perform more advanced configuration or even change the mode of operation, you can use the web-based utility provided by the manufacturer as described in the following sections. Access Point Mode When acting as an access point, this device connects all the stations (PC/notebook with wireless network adapter) to a wired network. All stations can have the Internet access if only the Access Point has the Internet connection. WDS Repeater Mode While acting as Bridges, AP1 (with Station 1 being associated to) and AP2 (with Station 2 being associated) can communicate with each other through wireless interface (with WDS). Thus Station 1 can communicate with Station 2 and both Station 1 and Station 2 are able to access the Internet if only AP1 or AP2 has the Internet connection. Client Mode (Infrastructure) If set to Client (Infrastructure) mode, this device can work like a wireless station when it’s connected to a computer so that the computer can send packets from wired end to wireless interface. Client Mode (Ad-hoc) If set to the Client (Ad-hoc) mode, this device can work like a wireless station when it is connected to a computer so that the computer can send packets from wired end to wireless interface. You can share files and printers between wireless stations (PC and laptop with wireless network adapter installed). WDS Bridge Mode The WDS (Wireless Distributed System) function lets this access point act as a wireless LAN access point and repeater at the same time. Users can use this feature to build up a large wireless network in a large space like airports, hotels and schools …etc. This feature is also useful when users want to bridge networks between buildings where it is impossible to deploy network cable connections between these buildings. CONFIGURATION Login 1. 2. 3. Start your computer. Connect an Ethernet cable between your computer and the Wireless Access Point. Make sure your wired station is set to the same subnet as the Wireless Access Point, i.e. 192.168.1.254 Start your WEB browser. In the Address box, enter the following: HTTP://192.168.1.254 The configuration menu is divided into four categories: Status, Wireless, TCP/IP, and Other settings. Click on the desired setup item to expand the page in the main navigation page. The setup pages covered in this utility are described below. No password required for the first login (the default setting), just enter the User name 'admin' which is systematically fixed. Afterwards, you can assign a password for a security consideration without changing the fixed user name. 10 Status In this screen, you can see the current settings and status of this Access Point. You can change settings by selecting specific tab described in below. System System The time period since the device was up. Uptime The current version of the firmware installed in this device. Firmware Version Wireless Configuration There are four modes supported, Access Point, Client (AdWireless Mode hoc and Infrastructure), WDS Bridge and WDS repeater. The default mode is Access Point. If you want to change to bridge mode, please go to Wireless/WDS Setting to enable the WDS function. The SSID differentiates one WLAN from another, therefore, SSID all access points and all devices attempting to connect to a specific WLAN must use the same SSID. It is case-sensitive and must not exceed 32 characters. A device will not be permitted to join the BSS unless it can provide the unique SSID. An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network. 11 Channel Number Encryption Associated Clients BSSID TCP/IP Configuration IP Protocol br0 IP Address br0 Subnet Mask br0 Default Gateway br0 MAC Address The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel. WEP Encryption (Wired Equivalent Privacy) is set to Disabled by default. When WEP is enabled, data packet is encrypted before being transmitted. The WEP prevents data packets from being eavesdropped by unrelated people. By using WEP data encryption, there may be a significant degradation of the data throughput on the wireless link. Displays the total number of clients associated to this AP. You can have up to 64 clients to associate to this Access Point. BSSID displays the ID of current BSS, which uniquely identifies each BSS. In AP mode, this value is the MAC address of this Access Point. Display the method to get the IP of this AP, which could be obtained by Fixed-IP or DHCP-client. Current IP address for this Access Point Current Subnet mask for this Access Point Default Gateway for this Access Point The MAC Address for this Access Point Statistics The Statistics table shows the packets sent/received over wireless and ethernet LAN respectively. 12 Wireless Basic Settings This page includes all primary and major parameters. Any parameter change will cause the device to reboot for the new settings to take effect. Disable Wireless LAN Interface Band Mode Network Type Check the box to disable the Wireless LAN Interface, by so doing, you won’t be able to make wireless connection with this Access Point in the network you are located. In other words, this device will not be visible by any wireless station. You can choose one mode of the following you need. ~2.4GHz (B): 802.11b supported rate only. ~2.4GHz (G): 802.11g supported rate only. ~2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate. The default is 2.4GHz (B+G) mode. This Wireless Access Point can support four modes AP, Client, Bridge and Repeater. When in Client mode, you can select between Ad-Hoc and Infrastructure. 13 The SSID differentiates one WLAN from another, therefore, all access points and all devices attempting to connect to a specific WLAN must use the same SSID. It is casesensitive and must not exceed 32 characters. A device will not be permitted to join the BSS unless it can provide the unique SSID. An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network. Allow user to set the channel manually or Channel Number automatically. If set channel manually, just select the channel you want to specify. If “Auto” is selected, user can set the channel range to have Wireless Access Point automatically survey and choose the channel with best situation for communication. The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel. Enable Mac Clone (Single Ethernet If your ISP restricts service to PCs only, use the MAC Clone feature to copy a PC Media Client) Access Control (MAC) address to your router. This procedure will cause the router to appear as a single PC, while allowing online access to multiple computers on your network. SSID Apply Changes Reset Press to save the new settings on the screen. Press to discard the data you have entered since last time you press Apply Change. Advanced Settings It is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance 14 Authentication Type To provide a certain level of security, the IEEE 802.11 standard has defined two types of authentication methods, Open System and Shared Key. With Open System authentication, a wireless PC can join any network and receive any messages that are not encrypted. With Shared Key authentication, only those PCs that possess the correct authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an Open System network. Wired Equivalent Privacy (WEP) data encryption is used when the wireless devices are configured to operate in Shared Key authentication mode. If the Access Point is using Open System, then the wireless adapter will need to be set to the same authentication mode. Shared Key is used when both the sender and the recipient share a secret key. Select Auto for the network adapter to select the Authentication mode automatically depending on the Access Point Authentication mode. 15 Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network. If your 802.11g Wireless LAN PC Card often transmit large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. RTS Threshold RTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem. “Hidden Node” is a situation in which two stations are within range of the same Access Point, but are not within range of each other. Therefore, they are hidden nodes for each other. When a station starts data transmission with the Access Point, it might not notice that the other station is already using the wireless medium. When these two stations send data at the same time, they might collide when arriving simultaneously at the Access Point. The collision will most certainly result in a loss of messages for both stations. Thus, the RTS Threshold mechanism provides a solution to prevent data collisions. When you enable RTS Threshold on a suspect “hidden station”, this station and its Access Point will use a Request to Send (RTS). The station will send an RTS to the Access Point, informing that it is going to transmit the data. Upon receipt, the Access Point will respond with a CTS message to all station within its range to notify all other stations to defer transmission. It will also confirm the requestor station that the Access Point has reserved it for the time-frame of the requested transmission. If the “Hidden Node” problem is an issue, please specify the packet size. The RTS mechanism will be activated if the data size exceeds the value you set.. The default value is 2347. Warning: Enabling RTS Threshold will cause redundant network overhead that could negatively affect the throughput performance instead of providing a remedy. This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Beacon Interval Beacon Interval is the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point). 16 Data Rate Preamble Type Broadcast SSID IAPP 802.11g Protection Tx Power Level Apply Change Reset By default, the unit adaptively selects the highest possible rate for transmission. Select the basic rates to be used among the following options: Auto, 1, 2, 5.5, 11or 54 Mbps. For most networks the default setting is Auto which is the best choice. When Auto is enabled the transmission rate will select the optimal rate. If obstacles or interference are present, the system will automatically fall back to a lower rate. A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. In a "noisy" network environment, the Preamble Type should be set to Long Preamble. The Short Preamble is intended for applications where minimum overhead and maximum performance is desired. If in a "noisy" network environment, the performance will be decreased. Select enabled to allow all the wireless stations to detect the SSID of this Access Point. IAPP (Inter Access Point Protocol) is designed for the enforcement of unique association throughout a ESS (Extended Service Set) and a secure exchange of station’s security context between current access point (AP) and new AP during handoff period. The 802.11g standard includes a protection mechanism to ensure mixed 802.11b and 802.11g operations. If there is no such kind of mechanism exists, the two kinds of standards may mutually interfere and decrease network’s performance. Select the Transmission rate level ranging from Highest, High, Middle, Low and Lowest. Press to save the new settings on the screen. Press to discard the data you have entered since last time you press Apply Change. 17 Security Here you can configure the security of your wireless network. Selecting different method will enable you to have different level of security. Please note that by using any encryption, by which data packet is encrypted before transmission to prevent data packets from being eavesdropped by unrelated people, there may be a significant degradation of the data throughput on the wireless link. Encryption: None ( Encryption is set to None by default. ) If Use 802.1x Authentication is selected, the RADIUS Server will proceed to check the 802.1x Authentication. Encryption: WEP If WEP is selected, users will have to Set WEP keys either manually, or select to Use 802.1x Authentication to make the RADIUS server to issue the WEP key dynamically. 18 Set WEP key Click the Set WEP Keys will prompt you a window to set 64bit or 128bit Encryption. Select HEX if you are using hexadecimal numbers (0-9, or A-F). Select ASCII if you are using ASCII characters (case-sensitive). Ten hexadecimal digits or five ASCII characters are needed if 64-bit WEP is used; 26 hexadecimal digits or 13 ASCII characters are needed if 128-bit WEP is used. Encryption: WPA (TKIP) WPA (TKIP): If WPA is selected, users will have to select the Authentication modes between Enterprise (RADIUS) and Personal (Pre-shared Key). Pre-shared Key Pre-Shared-Key serves as a password. Users may key in a 8 to 63 characters string to set the password or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is used on client's end. There are two formats for choice to set the Pre-shared key, i.e. Passphrase and Hex. If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the Passphrase (at least 8 characters) format is recommended. 19 Enter the number of seconds that will elapse before the group key change automatically. The default is 86400 seconds. Enable Pre-Authentication The two most important features beyond WPA to become standardized through 802.11i/WPA2 are: preauthentication, which enables secure fast roaming without noticeable signal latency. Preauthentication provides a way to establish a PMK security association before a client associates. The advantage is that the client reduces the time that it's disconnected to the network. Authentication RADIUS Port: Enter the RADIUS Server’s port number provided by your ISP. The default is 1812. Server IP Address: Enter the RADIUS Server’s IP Address provided by your ISP. Password: Enter the password that the AP shares with the RADIUS Server. Group Key Life Time Apply Change Press to save the new settings on the screen. Reset Press to discard the data you have entered since last time you press Apply Change. Access Control When Enable Wireless Access Control is checked, only those clients whose wireless MAC addresses listed in the access control list can access this Access Point. If the list contains no entries with this function being enabled, then no clients will be able to access this Access Point. 20 Wireless Access Control Select the Access Control Mode from the pull-down menu. Disable: Select to disable Wireless Access Control Mode. Mode Allow Listed: Only the stations shown in the table can associate with the AP. MAC Address Comment Apply Changes Reset Delete Selected Delete All Reset Deny Listed: Stations shown in the table won’t be able to associate with the AP. Enter the MAC Address of a station that is allowed to access this Access Point. You may enter up to 20 characters as a remark to the previous MAC Address. Press to save the new settings on the screen. Press to discard the data you have entered since last time you press Apply Change. To delete clients from access to this Access Point, you may firstly check the Select checkbox next to the MAC address and Comments, and press Delete Selected. To delete all the clients from access to this Access Point, just press Delete All without selecting the checkbox. If you have made any selection, press Reset will clear all the select mark. 21 TCP/IP Basic In this page, you can change the TCP/IP settings of this Access Point, select to enable/disable the DHCP Client, 802.1d Spanning Tree, and Clone MAC Address. IP Address Subnet Mask Default Gateway DHCP DHCP Client Range Show Client DNS Server This field can be modified only when DHCP Client is disabled. If your system manager assigned you static IP settings, then you will have to enter the information provided. Enter the information provided by your system manager. Enter the information provided by your system manager. Select Disable, Client or Server from the pull-down menu. Disable: Select to disable DHCP server function. Client: Select to automatically get the LAN port IP address from ISP (For ADSL/Cable Modem). Server: Select to enable DHCP server function. 253 IP addresses continuing from 192.168.1.1 to 192.168.1.253 Click to show Active DHCP Client table. Enter the Domain Name Service IP address. 22 802.1d Spanning Tree To enable 802.1d Spanning Tree will prevent the network from infinite loops. Infinite loop will happen in the network when WDS is enabled and there are multiple active paths between stations. Clone MAC Address Apply Change Reset You can specify the MAC address of your Access Point to replace the factory setting. Press to save the new settings on the screen. Press to discard the data you have entered since last time you press Apply Change. 23 Other Upgrade Firmware 1. 2. 3. Download the latest firmware from your distributor and save the file on the hard drive. Start the browser, open the configuration page, click on Other, and click Upgrade Firmware to enter the Upgrade Firmware window. Enter the new firmware’s path and file name (i.e. C:\FIRMWARE\firmware.bin). Or, click the Browse button, find and open the firmware file (the browser will display to correct file path). Click Reset to clear all the settings on this page. Or click Upload to start the upgrade. 24 Save/Reload Settings This function enables users to save the current configurations as a file (i.e. config.dat) To load configuration from a file, enter the file name or click Browse… to find the file from your computer. Save Settings to File: Click SAVE.. to save the current configuration to file. When prompted the upper left screen, select “Save this file to disk”, and the upper right screen will prompt you a dialog box to enter the file name and the file location. Load Settings From File: Click Browse… if you want to load a pre-saved file, enter the file name with the correct path and then click on Upload. Or click Browse… to select the file. 25 Reset: Click to restore the default configuration. 26 Password For secure reason, it is recommended that you set the account to access the web server of this Access Point. Leaving the user name and password blank will disable the protection. The login screen prompts immediately once you finish setting the account and password. Remember your user name and password for you will be asked to enter them every time you access the web server of this Access Point. New Password Confirm Password Apply Change Reset Set your new password. Password can be up to 30 characters long. Password can contain letter, number and space. It is case sensitive. Re-enter the new password for confirmation. Press to save the new settings on the screen. Press to discard the data you have entered since last time you press Apply Change. System Log This page display log events with time when events happened, log events’ types, log sources and the description for events themselves. System manager can use the system log to trace when problems occur. 27 Enable Log Apply Changes Refresh Clear Select System all or Wireless only. Press to save the new settings on the screen. Click to refresh the screen. Click to clear the current setting. 28
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Comments : Access Point (IEEE802.11b) Source Modified : D:20071221100450 Creator Tool : Acrobat PDFMaker 7.0.7 for Word Modify Date : 2008:01:03 10:03:53+08:00 Create Date : 2007:12:21 18:06:03+08:00 Metadata Date : 2008:01:03 10:03:53+08:00 Document ID : uuid:cf3f6242-a026-4fee-a112-2752a0fed4b8 Instance ID : uuid:6a2ecdb4-0b0c-4908-8eb5-1f3e5f6fdf49 Version ID : 7 Format : application/pdf Title : Wireless Access Point Creator : Eleen Lin Subject : Headline : Page Count : 31 Page Layout : OneColumn Author : Eleen LinEXIF Metadata provided by EXIF.tools