SmartLabs 2634222 On/Off Outdoor Module User Manual Owners Manual

Download:
Mirror Download [FCC.gov]
Document ID	1827634
Application ID	InHln5ANEky9m/mKYn4guQ==
Document Description	Owners Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.97kB (149586 bits)
Date Submitted	2012-11-01 00:00:00
Date Available	2012-11-01 00:00:00
Creation Date	2012-10-22 13:54:07
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2012-10-22 13:54:07
Document Title	Microsoft Word - Manual 2634-222 On-Off Outdoor 08162012.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	jlockyer

Quick Start Guide
INSTEON® On/Off Outdoor Module
Model: 2634-222
Introduction
On/Off Outdoor Module allows you to remotely control any appliance/device
outside your home at the touch of a button while retaining local control via load
sensing (see Owner’s Manual). Can be used with incandescent lamps up to
1800 Watts and inductive loads up to 15 Amps.
Status
LED
Outlet
Set
button
Installing On/Off Outdoor Module
1)
2)
3)
Plug appliance/device (also called the load) you want to control into On/Off Outdoor Module outlet
Plug On/Off Outdoor Module into unswitched wall outlet
Status LED will turn on solid green
The load will turn on. (If load does not turn on, tap Set button.)
Allow On/Off Outdoor Module to hang down from outlet (see image)
Make On/Off Outdoor Module a Responder
1)
Press and hold controller Set button until it beeps
2)
Controller LED will start blinking green
You will have four minutes to complete the next steps before linking mode times out
Use On/Off Module Set button to adjust load to desired level (on or off)
3)
Press and hold On/Off Module Set button until it double-beeps
4)
Controller will double-beep and its LED will stop blinking
Test link by tapping controller button on and off
Load connected to On/Off Module will respond appropriately
Make On/Off Outdoor Module a Controller
1)
2)
Press and hold On/Off Module Set button until it beeps
On/Off Module LED will start blinking green
Adjust responder to desired brightness state (such as on, 50% or even off)
3)
Press and hold responder Set button until it double-beeps
4)
On/Off Module LED will stop blinking
Test by tapping On/Off Module Set button to turn on/off
Responder will respond appropriately
Owner’s Manual and Tech Support
Owner’s Manual and current Quick Start Guide: http://www.insteon.com/support
Call: INSTEON Support Line at 800-762-7845
FCC Compliance
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le
brouillage est susceptible d'en compromettre le fonctionnement.
The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15B of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by
turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:
- Re-orient or relocate the receiving antenna of the device experiencing the interference
- Increase the distance between this device and the receiver
- Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver
- Consult the dealer or an experienced radio/TV technician
WARNING: Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Create Date                     : 2012:10:22 13:54:07-07:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2012:10:22 13:54:07-07:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - Manual 2634-222 On-Off Outdoor 08162012.doc
Creator                         : jlockyer
Document ID                     : uuid:f1880a35-98d3-46a3-a519-066b881a1c92
Instance ID                     : uuid:be035390-3d0a-4690-953f-8e47e3dec724
Page Count                      : 1
Author                          : jlockyer

EXIF Metadata provided by EXIF.tools