SmartLabs 4715 7 Day Thermostat User Manual Quick Start Guide
SmartLabs, Inc. 7 Day Thermostat Quick Start Guide
Users Manual
Quick-Start Guide Backlit LCD Display Up button (glows red) 7 Day Thermostat Model: 4715 Installation Down button (glows blue) 1) RF-only devices require at least one dual-band INSTEON product for communication. For the best INSTEON network performance, be sure you have properly installed at least two dual-band INSTEON products. 2) Remove the old thermostat, but keep the old thermostat for reference purposes, until 7 Day Thermostat is functioning properly 3) Remove the front cover from 7 Day Thermostat 4) Mount 7 Day Thermostat using the included hardware 5) Configure the jumpers. (See the 7 Day Thermostat Installation and Programming Guide.) 6) Refer to the chart and diagrams below for basic 1 stage cooling, 1 stage heat wiring. For other wiring diagrams, see the Installation and Programming Guide. Wire from the old thermostat Install on the new thermostat Function terminal marked connector marked G or F Fan Y1, Y, or C Cooling Y1 W1, W or H Heating W1/O/B Rh, R, M, Vr, A Power Common O/B Rev. Valve W1/O/B W2 2nd Stage Heat W2 MISC1 Configurable Output #1 MISC1 MISC2 Configurable Output #2 MISC2 MISC3 Configurable Output #3 MISC3 RS+5 Remote Sensor +5vdc RS+5 RS1 Remote Sensor Signal RS1 RSGND Remote Sensor Ground RSGND RS2 Remote Sensor Signal #2 RS2 7) Reattach the front cover to 7 Day Thermostat Mode button Heat or Cool Demand Indicator Wiring Diagrams Residential & Commercial 1 Stage Cooling, with 1st Stage Gas Heat Residential & Commercial 1 Stage Cooling, with 1st Stage Electric Heat Controlling 7 Day Thermostat • Tap an On or Scene button on a Linked Controller to recall the thermostat mode and set points established during Linking • Tap an Off button on a Linked Controller to turn off the thermostat and set points established during Linking • Tap the Bright* button on a Linked Controller to raise the set point(s) by a single degree • Tap the Dim* button on a Linked Controller to lower the set point(s) by a single degree *To prevent “runaway” temperature set points, these operations only apply to Controllers with Bright/Dim buttons. Page 1 of 2 Rev. 09-23-2010 SMART Limited Warranty – SMART warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be free from defects in material & workmanship & will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by misuse or neglect. U.S. Patent No. 7,345,998, International patents pending © Copyright 2010 SMART, 16542 Millikan Ave., Irvine, CA 92606, 866-883-9220 FCC & Industry Canada Compliance Statement This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is not guarantee that interference will no occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures: • Re-orient or relocate the receiving antenna of the device experiencing the interference • Increase the distance between this device and the receiver • Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver • Consult the dealer or an experienced radio/TV technician WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Complete Instructions, Troubleshooting, and Tech Support Call: Tech. Support @ 866-883-9220 Contact Us Online: www.smartproline.com Page 2 of 2 Rev. 09-23-2010 SMART Limited Warranty – SMART warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be free from defects in material & workmanship & will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by misuse or neglect. U.S. Patent No. 7,345,998, International patents pending © Copyright 2010 SMART, 16542 Millikan Ave., Irvine, CA 92606, 866-883-9220
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 8.1.0 (Windows) Company : SmartLabs Inc., Source Modified : D:20100928175538 Creator Tool : Acrobat PDFMaker 8.1 for Word Modify Date : 2010:09:28 10:56:34-07:00 Create Date : 2010:09:28 10:56:25-07:00 Metadata Date : 2010:09:28 10:56:34-07:00 Document ID : uuid:b3ebcec1-4298-4dcd-a31b-167b150d2474 Instance ID : uuid:7ef9b477-d787-4e87-8489-edd7e2768946 Subject : 4 Format : application/pdf Creator : Joew Title : Quick-Start Guide Page Count : 2 Page Layout : OneColumn Author : JoewEXIF Metadata provided by EXIF.tools