Snapper EI7243 7 3334D User Manual To The 89b406c6 F0d1 4939 Ae28 3dee0bcdc07d

User Manual: Snapper EI7243 to the manual

Open the PDF directly: View PDF PDF.
Page Count: 24

Safety Instructions & Operator’s Manual for
EUROPEAN
TWO STAGE
INTERMEDIATE FRAME
SNOW THROWER
SERIES 3
MODELS
EI55223
EI7243
MODEL NUMBER EXPLANATION
E I 55 22 3
MODEL DESIGNATION SERIES DESIGNATION
ENGINE HP AUGER WIDTH
E – European Model 55 – 5.5 Engine HP (Engine Horse Power) 22 – 22” Auger Width
I – Intermediate Frame Model 7 – 7.0 Engine HP (Engine Horse Power) 24 – 24” Auger Width
3 – Series Designation
Thank you for buying a SNAPPER Product! Before operating your Snow Thrower, read this manual carefully and pay
particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power
equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance
with the operating instructions and common sense.
COPYRIGHT © 2000
SNAPPER INC.
ALL RIGHTS RESERVED INSTRUCTION No. 7-3334 (I.R. 02/14/00)
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury
and damage! Failure to comply with the following instructions may result in serious injury to the operator or
other persons. The owner of the snow thrower must understand these instructions and, furthermore, must
allow only persons who understand these instructions to operate snow thrower. Each person operating the
snow thrower must be of sound mind and body and must not be under the influence of any substance, which
might impair vision, dexterity, or judgment. If you have any questions pertaining to your snow thrower which
your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER,
McDonough, Georgia 30253. Phone: 800/935-2967.
PROTECTION FOR CHILDREN
Tragic accidents can occur if the operator is not alert
to the presence of children. Children are often
attracted to the machine and the snow removal
activity. Never assume that the children will remain
where you last saw them.
1. DO NOT allow children in the area when snow
thrower is being operated.
2. DO NOT allow pre-teenage children to operate
snow thrower.
3. ALLOW only responsible adults and teenagers
with mature judgment to operate the machine
and then only after being thoroughly instructed
and under the close supervision of an
experienced adult operator.
4. Keep the area clear of all persons, particularly
small children and pets.
5. Know how to STOP the snow thrower and
disengage the controls quickly.
PREPARATION
1. Warn everyone in advance to stay clear of area.
Keep especially watchful for children and pets
darting into area while operating.
2. Read, understand, and follow instructions and
warnings in this manual and on the machine.
Know the controls and the proper use of the
snow thrower before starting.
3. Data indicates that operators, age 60 and above,
are involved in a large percentage of snow
thrower-related injuries. These operators should
evaluate their ability to operate the snow thrower
safely enough to protect themselves and others
from serious injury.
4. Disengage all clutches and shift into neutral
before starting the engine (motor).
5. Wear adequate winter clothing including boots
which will give you maximum footing on slippery
surfaces. Exercise CAUTION to avoid slipping or
falling.
6. Before the first snow fall, check the area to be
cleared and remove all objects such as
doormats, sticks, toys, wires, rocks, etc., which
could be hurled or jam the snow thrower
PREPARATION
(Continued From Previous Column)
7. Survey the area to be cleared beforehand and
plan where snow is to be blown. Be prepared to
release auger/impeller clutch or to change
discharge chute direction quickly to discharge
away from windows, cars, buildings and
doorways to avoid property damage or personal
injury from hurled objects.
8. Use only approved extension cords and
receptacles in good condition and with sufficient
capacity to carry the current to the machine if
equipped with electric starting motors.
9. Handle fuel with extra care. Fuels are flammable
and vapors are explosive. Store only in an
approved fuel container. Never remove fuel cap
or add fuel with the engine running. Add fuel
outdoors only with the engine stopped and cool.
Clean spilled fuel and oil from machine. DO NOT
smoke. DO NOT run engine indoors.
OPERATIONAL PRECAUTIONS
1. Before starting, make visual check to make sure
auger/impeller housing is clear and all guards
and shields are in place and tight.
2. DO NOT operate machine without proper guards
shields, deflectors, or other safety protective
devices in place and functioning properly.
3. Should the auger/impeller become clogged,
release the auger/impeller clutch control and, as
an additional precaution, STOP the engine
before attempting to unclog the auger/impeller or
discharge chute.
4. DO NOT attempt to unclog the auger/impeller or
discharge chute by reaching in with your hands.
Use a long stick or similar implement to unclog.
5. DO NOT attempt to unclog the auger/impeller or
discharge chute with the engine running. STOP
engine and remove key.
6. STOP engine (motor) and remove key before
leaving the operator position for any reason.
3
IMPORTANT SAFETY INSTRUCTIONS
OPERATIONAL PRECAUTIONS
(Continued From Previous Page)
7. DO NOT put hands or feet near or under
rotating parts. Keep clear of the discharge
opening at all times.
8. Start engine only where exhaust fumes will be
safely dissipated. Allow a brief warm-up period,
and practice operation of controls outside
before putting the machine to work.
9. After striking a foreign object, STOP the engine
(motor), remove the key, and remove the wire
from spark plug. Thoroughly inspect the snow
thrower for any damage, and repair the damage
before restarting and operating the snow
thrower.
10. STOP the engine if the machine starts to vibrate
excessively as this normally indicates
mechanical problems. Remove the key and
disconnect the spark plug wire to prevent
unintentional starting before servicing or
repairing the machine.
11. DO NOT clear snow across the face of slopes.
Exercise extreme CAUTION when changing
direction on slopes. DO NOT attempt to clear
steep slopes.
12. DO NOT leave machine unattended with the
engine running. STOP engine and remove key
to prevent unauthorized operation.
13. Release clutch control and make sure
auger/impeller has STOPPED before adjusting
deflector, or placing hands near auger/impeller.
14. DO NOT use snow thrower on surfaces above
ground level, such as, a roof of a building.
15. Exercise extreme CAUTION when operating on
or crossing gravel drives, walks, or roads. Stay
alert for hidden hazards or traffic.
16. DO NOT overload the machine capacity by
attempting to clear snow at too fast a rate.
17. Never operate the machine at high transport
speeds on slippery surfaces. Look behind and
use care when backing.
18. Disengage power to the auger/impeller when
snow thrower is transported or not in use.
19. Use only attachments and accessories
approved by the manufacturer of the snow
thrower (such as wheels weights,
counterweights, cabs and the like).
20. Never operate the snow thrower without good
visibility or light. Always be sure of your
footing, and keep a firm hold on the handles.
Walk; never run.
MAINTENANCE AND STORAGE
1. DO NOT store machine or fuel container inside
where fumes may reach an open flame, spark,
or pilot light as in a water heater, furnace,
clothes dryer or other gas appliance. Allow
engine to cool before storing machine in an
enclosure. Store fuel container out of reach of
children in a well ventilated, unoccupied
building.
2. Keep machine and engine free of excess oil,
grease and spilled fuel to reduce fire hazard.
3. When draining fuel tank, drain fuel into an
approved container outdoors and away from
open flame.
4. Inspect all bolts, nuts and screws frequently
and keep properly tightened.
5. Use only recommended shear bolts (if
equipped) to prevent possible damage to
machine.
6. Service engine and make adjustments only
when engine is stopped. Remove key, remove
wire from spark plug, secure wire away from
plug, and disconnect cord from electric starting
motors to prevent accidental starting.
7. DO NOT change engine governor speed
settings or overspeed engine.
8. DO NOT test for spark by grounding the spark
plug next to spark plug hole. Spark from the
plug could ignite gas exiting engine.
9. Have machine serviced by an authorized
SNAPPER dealer at least once a year and have
the dealer install any new safety devices.
10. Use only genuine SNAPPER replacement parts
to assure that original standards are
maintained.
4
TABLE OF CONTENTS
SECTION 1 - IMPORTANT SAFETY INSTRUCTIONS..........................2-3
TABLE OF CONTENTS ............................................................................ 4
DECALS ................................................................................................. 5-6
SECTION 2 - OPERATING INSTRUCTIONS.......................................7-11
Pre-start Checklist ..................................................................................................... 7
Starting, Operation & Stopping (Recoil Start Models)......................................... 8-9
Starting, Operation & Stopping (Electric Start Models) .................................. 10-11
Starting & Stopping Auger ................................................................................... 9-11
Starting & Stopping Wheel Drive.........................................................................9-11
SECTION 3 - MAINTENANCE INSTRUCTIONS................................12-13
Checking Auger Drive Belt ...................................................................................... 12
Checking Wheel Drive Belt...................................................................................... 12
Lubricate Gear Case................................................................................................. 12
Lubricate Auger & Bearing ...................................................................................... 12
General Lubrication.................................................................................................. 12
Annually – (End Of Each Season)........................................................................... 13
Engine .................................................................................................................... 13
Spark Plug.............................................................................................................. 13
Storage Procedure ................................................................................................... 13
Maintenance and Service Parts .............................................................................. 13
SECTION 4 - REPAIR AND ADJUSTMENTS....................................14-19
Auger & Wheel Drive Belt Adjustment .............................................................. 14-15
Auger & Wheel Drive Belt Replacement............................................................ 15-16
Ground Speed Adjustment...................................................................................... 17
Skid Shoe Adjustment ............................................................................................. 17
Auger Shear Bolt Replacement............................................................................... 17
Single Handle Control Adjustment (7 HP Models Only) ....................................... 18
Chute Crank Adjustment ......................................................................................... 19
Rubber Drive Tire Replacement.............................................................................. 19
TROUBLESHOOTING ............................................................................ 20
SERVICE SCHEDULE ............................................................................ 20
WARRANTY............................................................................................ 21
5
DECALS
DANGER ROTATING IMPELLER. DO NOT use hand
to unclog auger/impeller or discharge chute. Stop
engine and remove key before unclogging.
GROUND SPEED CONTROL. Snowthrower has 4
Forward speeds and 1 Reverse speed. Rabbit/Fast.
Turtle/Slow. R/Reverse.
DANGER ROTATING AUGER. Keep Away. DO NOT
allow children or others in the area when Snowthrower
is being operated.
YEAR OF MANUFACTURE
EUROPEAN COMMUNITY
DISCHARGE CHUTE. Rotate control to discharge snow
in desired direction.
DEADMAN CONTROLS. Depress to engage. Release
to disengage/stop. Left control – wheel drive. Right
control – auger/impeller.
Read, understand & follow all manuals and instructions
furnished with the Snowthrower.
6
DECALS
HEARING PROTECTION REQUIRED.
Machine exceeds 100Lwa.
MAXIMUM HANDLE VIBRATION 34 M/SEC2.
DANGER – ROTATING AUGER. KEEP AWAY.
SAFETY INSTRUCTIONS TO PREVENT INJURY:
1) Read Owner’s Manual for operating and safety
instructions.
2) Observe all labels and instructions.
3) DO NOT defeat safety features of controls. They
are for your protection.
4) Stop engine, wait for all moving parts to stop,
remove spark plug wire before unclogging or
servicing machine.
5) Never allow children to operate the equipment.
Never allow adults to operate equipment without
proper instruction.
6) Keep area of operations clear of all persons,
especially children.
7) Never direct discharge at bystanders or allow
anyone in front of unit.
8) Keep machine properly maintained and serviced
with all shields, guards, or protective devices in
place.
7
Section 2 - OPERATING INSTRUCTIONS
2.1 PRE-START CHECK LIST
Make the following checks and perform the service
required before each start-up.
2.1.1. Check engine oil and add oil as needed to bring
level up to the FULL mark. Refer to engine owner’s
manual for oil specifications
2.1.2. Check guards, chutes, deflectors and covers to
make sure all are in place and securely tightened.
2.1.3. Check auger control and wheel drive control
to insure cables are connected and both levers
operate freely. See Figure 2.1.
IMPORTANT: On 7 HP models only. Standing in the
operator’s position, the left handle bar lever is for wheel
drive engagement and disengagement. The right handle
bar lever is for auger/impeller engagement and
disengagement. Hold both levers down to handle bar for
engagement and release levers for disengagement.
When both levers are pressed down to the handle bar at
the same time, the operator can release the right hand
lever and the right lever will remain engaged as long as
the left hand lever is held down to handle bar. Release
the left hand lever and both levers will disengage.
FIGURE 2.1
2.1.4. Check chute operation. Rotate chute crank to
insure smooth rotation throughout its range.
2.1.5. Check tires and add or release air as needed
to bring air pressure to 12 psi without tire chains. Air
pressure with tire chains should be 16 psi.
WARNING
Use approved fuel container. DO NOT smoke near
open fuel container. DO NOT fill fuel tank indoors or
when engine is running. Allow engine to cool for at
least ten minutes before refilling. Wipe off any
spilled fuel before starting engine. DO NOT run
engine indoors.
2.1.6. Add fuel to tank after pushing the machine
outside where fumes can safely dissipate. Make sure
cap is tightened after refueling. Wipe up any spilled
fuel on machine and surrounding area. Refer to
Engine Owners Manual for specifications.
2.1.7. Check auger housing and discharge chute,
both must be free of all obstructions. Clean engine of
any accumulation of spilled fuel, dirt, etc.
WARNING
DO NOT use an electrical extension cord that is
damaged. A damaged electrical extension cord could
cause a shock or fire. Thoroughly inspect electrical
extension cord before using machine. If cord is
damaged, do not use and do not operate machine.
Replace damaged cord immediately. Contact your
Snapper service dealer for assistance. To reduce the
risk of electric shock, use only with an extension
cord intended for outdoor use having a cord type:
SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A or
SJTOW-A.
IMPORTANT: Electric Start Kit optional accessory on
some models.
2.1.8. Check and make sure extension cord is in
good condition. Extension cord should not have any
broken insulation or exposed wires. Use an
extension cord that is heavy enough to carry the
correct amount of current to the machine. See
Figure 2.2 for correct size to use depending on cord
length and nameplate ampere rating. If in doubt,
use the next heavier gauge cord.
MINIMUM GAUGE FOR CORD SETS
120 or 230 Volt Total Length of Cord in Feet
Rating - Amps 25 ft.
50 ft. 100 ft.
150 ft.
More
Than Not More
Than A.W.G.
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not
Recommended
FIGURE 2.2
WHEEL DRIVE
CONTROL
AUGER/IMPELLER
CONTROL
8
Section 2 - OPERATING INSTRUCTIONS
2.2 STARTING, OPERATION & STOPPING
(RECOIL START MODELS)
(Go to Page 10 for Electric Start Models)
2.2.1. ENGINE
1. Turn fuel shut off valve to the “ON” position. See
Figure 2.3.
FIGURE 2.3
2. Insert key into ignition switch. See Figure 2.4.
3. Move choke control to the choke, “ON” position.
See Figure 2.4.
4. Move engine speed control to the “FAST”
position. See Figure 2.4.
IMPORTANT: Stop the auger and wheel drive by
releasing the auger and wheel drive control levers. Stop
the engine by moving the engine speed control to the
stop position or removing the key from the switch.
FIGURE 2.4
5. Push primer button three times to start a cold
engine. NOTE: Do not use primer button to start
warm engine. See Figure 2.4.
6. Pull rope start handle to crank engine.
7. After engine starts, move the choke control to
the no choke “OFF” position. Allow a brief warm-up
until engine runs smooth.
2.2.2. PROPELLING SNOW THROWER
IMPORTANT: This snow thrower has four forward
speeds and one reverse speed.
1. Move ground speed control to the desired speed
position. See Figure 2.5.
2. Proceed to Section 2.2.3. to engage auger and
2.2.4. to engage wheel drive.
FIGURE 2.5
TURN VALVE TO
“ON” POSITION
PUSH PRIMER
THREE TIMES
MOVE ENGINE
SPEED CONTROL
TO FAST
INSERT KEY
MOVE
CHOKE TO
THE “ON”
POSITION
GROUND
SPEED
CONTROL
MOVE GROUND
SPEED CONTROL
TO DESIRED
POSITION
9
Section 2 - OPERATING INSTRUCTIONS
WARNING
Objects can be thrown by the snow thrower while it
is in operation. Thrown objects could cause serious
injury to the operator or bystanders. Always wear
safety goggles or other suitable eye protection.
Keep people and pets away from area.
2.2.3. ENGAGING AUGER
1. Move auger control lever against handle to
engage auger. See Figure 2.6.
2.2.4. ENGAGING WHEEL DRIVE
1. Move wheel drive control lever against handle to
engage wheel drive. See Figure 2.6. Ground speed
can be changed while the machine is in operation
by changing position of the ground speed control.
IMPORTANT: This snow thrower has four forward
speeds and one reverse speed. See Figure 2.5.
FIGURE 2.6
WARNING
Release auger clutch and wheel drive controls and
make sure auger/impeller and wheel drive have
STOPPED before rotating discharge chute, adjusting
deflector, or placing hands near auger/impeller.
2.2.5. DISCHARGE CHUTE and DEFLECTOR
ADJUSTMENT
1. Release auger control and wheel drive control
levers to allow auger and ground speed to come to a
complete stop. See Figure 2.6.
2. Loosen deflector knob and position deflector to
desired angle. Retighten knob.
3. Rotate chute crank to position discharge chute
in desired direction. See Figure 2.6.
2.2.6. STOPPING - ENGINE, AUGER & WHEEL
DRIVE
Stop the auger and wheel drive by releasing the
auger and wheel drive control levers. See Figure
2.6. Stop the engine by removing the key from the
switch or moving engine speed control to the
STOP position. Always remove key from key
switch before leaving machine unattended. See
Figure 2.7.
FIGURE 2.7
MOVE WHEEL DRIVE
CONTROL AGAINST
HANDLE TO ENGAGE
WHEEL D
RIVE
MOVE AUGER
CONTROL AGAINST
HANDLE TO
ENGAGE AUGER
ROTATE CHUTE
CRANK TO CHANGE
DIRECTION OF
DISCHARGE CHUTE
MOVE ENGINE
SPEED CONTROL
TO “STOP”
POSITION TO STOP
ENGINE
REMOVE KEY TO
STOP ENGINE
10
Section 2 - OPERATING INSTRUCTIONS
2.2 STARTING, OPERATION & STOPPING
(ELECTRIC START MODELS)
(Go to Page 8 for Recoil Start Models)
WARNING
DO NOT use an electrical extension cord that is
damaged. A damaged electrical extension cord
could cause a shock or fire. Thoroughly inspect
electrical extension cord before using machine. If
cord is damaged, do not use and do not operate
machine. Replace damaged cord immediately.
Contact your Snapper service dealer for assistance.
To reduce the risk of electric shock, use only with
an extension cord intended for outdoor use having
a cord type: SW-A, SOW-A, STW-A, STOW-A, SJW-
A, SJTW-A or SJTOW-A.
2.2.7. ENGINE
1. Turn fuel shut off valve to the “ON” position.
See Figure 2.3.
2. Insert key into ignition switch. See Figure 2.8.
3. Connect the power cord to the starter switch
box on the engine, then plug the other end into 120
volt AC receptacle.
4. Move choke control to the choke, “ON” position.
See Figure 2.8.
IMPORTANT: Stop the auger and wheel drive by
releasing the auger and wheel drive control levers. Stop
the engine by moving the engine speed control to the
stop position or removing the key from the switch.
5. Move engine speed control to the “FAST”
position. See Figure 2.8.
6. Push primer button three times to start a cold
engine. NOTE: Do not use primer button to start
warm engine.
7. Push the electric starter button. DO NOT hold
button for more than 20 seconds to avoid
damaging the starting motor. See Figure 2.8.
8. After engine starts, move the choke control to
the no choke “OFF” position. Allow a brief warm-up
until engine runs smooth.
9. Disconnect power cord from AC receptacle.
Disconnect power cord from machine and remove
cord from area where machine will be in operation.
FIGURE 2.8
2.2.8. PROPELLING SNOW THROWER
IMPORTANT: This snow thrower has four forward
speeds and one reverse speed.
1. Move ground speed control to the desired
speed position. See Figure 2.5.
2. Proceed to Section 2.2.9. to engage auger and
Section 2.2.10. to engage wheel drive.
PUSH
STARTER
BUTTON
INSERT POWER
CORD INTO
STARTER BOX
PUSH PRIMER
THREE TIMES
MOVE CHOKE
TO THE “ON”
POSITION
MOVE ENGINE
SPEED
CONTROL TO
THE “FAST”
POSITION
INSERT
KEY
11
Section 2 - OPERATING INSTRUCTIONS
WARNING
Objects can be thrown by the snow thrower while it
is in operation. Thrown objects could cause serious
injury to the operator or bystanders. Always wear
safety goggles or other suitable eye protection. Keep
people and pets away from area.
2.2.9. ENGAGING AUGER
1. Pull auger control lever against handle to engage
auger. See Figure 2.6.
2.2.10. ENGAGING WHEEL DRIVE
1. Move wheel drive control lever against handle to
engage wheel drive. Ground speed can be adjusted
while the machine is moving by changing position of
the ground speed control. Machine has four forward
speeds and one reverse. See Figure 2.6.
WARNING
Release auger clutch control and make sure
auger/impeller has STOPPED before rotating
discharge chute, adjusting deflector or placing
hands near auger/impeller.
2.2.11. DISCHARGE CHUTE and DEFLECTOR
ADJUSTMENT
1. Release auger control and wheel drive control
levers to allow auger and ground speed to come to
a complete stop.
2. Loosen deflector knob and position deflector to
desired angle. Retighten knob.
3. Rotate chute crank to position discharge chute in
desired direction. See Figure 2.6.
2.2.12. STOPPING - ENGINE, AUGER & WHEEL
DRIVE
Stop the auger and wheel drive by releasing the
auger and wheel drive control levers. Stop the
engine by moving the engine speed control the stop
position or removing the key from the switch.
Always remove key from key switch before leaving
machine unattended. See Figure 2.7.
12
Section 3 - MAINTENANCE
WARNING
Before attempting any adjustments, maintenance,
service, or repairs, stop engine and auger, always
remove key from ignition switch, remove spark plug
wire and secure wire away from spark plug.
3.1 INTRODUCTION
To retain the quality of the snow thrower, use only
genuine SNAPPER replacement parts. Contact a
local SNAPPER dealer for parts and service
assistance. For the correct part or information for a
particular snow thrower, always mention model and
serial number.
3.2 SERVICE - AFTER FIRST 5 HOURS
3.2.1 CHECK AUGER DRIVE BELT
1. Visually check engine drive belt for cracking,
fraying, severed or belt strands exposed. Replace belt
before operating snow thrower. See Figure 3.1
3.2.2 CHECK WHEEL DRIVE BELT
1. Visually check wheel drive belt for cracking,
fraying, severed or belt strands exposed. Replace belt
before operating snow thrower. See Figure 3.1.
FIGURE 3.1
3.3 GENERAL LUBRICATION
Lubricate machine as instructed before and after
operation each season.
3.3.1. GEAR CASE, AUGER SHAFT and AUGER
BEARING LUBRICATION
1. Before each season of operation, apply two
shots of grease (Snapper suggests using Benelene
900) from a grease gun into gear case. The grease
fitting for the gear case is located in front of the
gear case. See Figure 3.2.
2. Before each season of operation, apply two
shots of grease (Snapper suggests using Benelene
900) from a grease gun into auger bearing. The
grease fitting for the auger bearing is located on
each end of the auger. See Figure 3.2.
3. Before each season of operation, apply two
shots of grease (Snapper suggests using Benelene
900) from a grease gun into the auger shaft. The
grease fitting for the auger shaft is located in the
middle of each auger. Remove shear bolts and
rotate auger to distribute grease evenly around
shaft. Reinstall shear bolts and nuts. Tighten to 5 to
10 ft. lb. of torque. See Figure 3.2.
FIGURE 3.2
3.3.2. GENERAL LUBRICATION
After each season of operation, spread a small
amount of grease on: The axle shafts for easy
wheel removal. The discharge chute and mounting
flange retainers for smooth rotation.
CHECK
WHEEL DRIVE
BELT
CHECK AUGER
DRIVE BELT
GEAR CASE
GREASE FITTING
AUGER BEARING
GREASE FITTING
AUGER SHAFT
GREASE FITTING
13
Section 3 - MAINTENANCE
3.4 ANNUALLY (END OF EACH SEASON)
Perform all maintenance as described in the maintenance
schedule.
3.4.1. Engine
Refer to engine owner’s manual for service
instructions.
3.4.2. Spark Plug
Refer to engine owner’s manual for service
instructions.
3.5 STORAGE PROCEDURE
Refer to the Engine Owner’s Manual for directions
regarding engine storage preparations. Prepare the snow
thrower for “end of season” storage as follows:
1. Drain fuel from fuel tank and let engine run until
all fuel is out of the carburetor.
2. Disconnect and remove the spark plug wire
away from spark plug before any other
preparations are made!
3. Tape all openings closed to prevent spraying
water into exhaust or air intakes during washing.
4. Tilt snow thrower up on its wheels and
thoroughly clean the underside of the auger.
5. Lubricate all exposed metal with a light coating
of oil to prevent corrosion.
6. Store the machine in a shed or other dry area,
protected from weather.
3.6 MAINTENANCE and SERVICE PARTS
MAINTENANCE and SERVICE PARTS
Auger Drive Belt (Tecumseh Engines) 1-5152
Wheel Drive Belt (4 HP & 5 HP Engines) 1-5151
Wheel Drive Belt (5.5 HP Engines) 4-5214
Wheel Drive Belt (6 HP & 7 HP Engines) 2-3416
Scraper Blade (22” Width Auger) 3-3298
Scraper Blade (24” Width Auger) 3-6163
Rubber Drive Tire 2-3364
Shear Bolts - 1/4-20 x 1-1/2” 1-5257
Hex Nuts - 1/4-20 7-6978
Parts Manual for Intermediate Frame Snow Thrower - Series 3
Domestic Models: I4223, I5223, I55223, I6223, I7243,
European Models: EI5223,EI55223, EI7243
#06045
14
Section 4 - REPAIR & ADJUSTMENTS
WARNING
Before attempting any adjustments, maintenance,
service, or repairs, stop engine and auger, always
remove key from ignition switch, remove spark plug
wire and secure wire away from spark plug.
4.1 AUGER BELT ADJUSTMENT/REPLACEMENT
When operating machine release the auger clutch
control, auger should come to a complete stop in 5
seconds. If auger does not come to a complete stop in
the required time, check and adjust belt tension.
Inspect belt frequently for signs of excessive wear.
Observe drive belt for slippage due to wear when
operating machine. If slippage does occur adjust as
follows.
4.1.1. AUGER and DRIVE BELT ADJUSTMENT
(CABLE ADJUSTMENT)
1. Measure control cable extension from a relaxed
position to full extended position. Move control lever
against handle. Measure from the top of spring (The
top is in relation to where spring connects into
connector). Proper extension should be 3/8” extension.
See Figure 4.1.
FIGURE 4.1
2. Adjust control cable by loosening jam nut at the
upper end of cable. Hold threaded end of cable and
then turn cable clockwise or counter clockwise until
correct extension is achieved. Retighten jam nut.
IMPORTANT: DO NOT rotate cable beyond the point to
where all of slack is out of cable. Cables have to have a
certain amount of slack: When control lever is in the
released position the cable slack allows: 1) Auger brake to
stop auger. 2) Wheel drive to disengage. If all of the
adjustment is utilized at the upper handle go to Section
4.1.2. for alternate adjustment.
4.1.2. AUGER BELT ADJUSTMENT
(IDLER PULLEY ADJUSTMENT)
NOTE: Wheel drive belt idler pulley is not adjustable. If
upper cable adjustment performed in Section 4.1.1.
and correct cable extension can not be accomplished,
adjustment can be made at the idler pulley. All
adjustment made in Section 4.1.1. will have to be
reversed from the upper end of cable.
1. Loosen jam nut at the end of cable. Hold threaded
end of cable and then turn metal housing of cable
counter clockwise until threaded portion of cable is
extracted from metal housing. Reinstall 1/2” of the
threaded portion of cable back into metal housing.
Retighten jam nut.
2. Remove belt cover. See Figure 4.2
FIGURE 4.2
3. Loosen nut and bolt that secures the idler pulley.
Move idler toward belt for more tension or away from
belt for less tension. See Figure 4.3. Retighten bolt and
nut securely.
FIGURE 4.3
CONNECTOR
JAM
NUT
(WHEN ENGAGED)
X+3/8”
SPRING SHOULD
STRETCH 3/8”
WHEN HANDLE IS
DEPRESSED
REMOVE
BELT
COVER
IDLER ARM
IDLER PULLEY ASSEMBLY
SHOWN EXPLODED TO
SHOW DETAIL OF IDLER
ARM SLOT
LEFT
RIGHT
MOVE IDLER PULLEY TO
LEFT INCREASE OR TO
RIGHT DECREASE
TENSION ON BELT
IDLER
ARM
15
Section 4 - REPAIR & ADJUSTMENTS
WARNING
Before attempting any adjustments, maintenance,
service, or repairs, stop engine and auger, always
remove key from ignition switch, remove spark plug
wire and secure wire away from spark plug. Before
tilting machine, drain all the fuel from fuel tank.
Allow engine to run, outdoors where fumes can be
safely dissipated, until all fuel is removed from
carburetor.
4.1.2. AUGER BELT ADJUSTMENT
(IDLER PULLEY ADJUSTMENT)
(Continued From Previous Page)
4. Recheck cable for proper extension.
5. Reinstall belt cover.
4.1.3. AUGER BELT REPLACEMENT
Inspect belt frequently for signs of excessive wear.
Visually check engine drive belt for cracking,
fraying, severed or belt strands exposed. NOTE:
Auger and Drive Belts are difficult to install. It may
be necessary to allow an authorized Snapper
Dealer to install these belts.
1. Remove belt cover. See Figure 4.2.
2. Remove discharge chute.
3. Loosen both auger/impeller belt guides. See
Figure 4.4.
IMPORTANT: Wheel drive belt will have to be removed
from around engine drive pulley and engine shaft to
install auger drive belt.
4. Remove auger drive belt from around engine
pulley. See Figure 4.4.
FIGURE 4.4
5. Tilt machine forward to gain access to drive
system area. Secure machine in the tilted position
to prevent tipping over. Remove drive system cover
plate. See Figure 4.5.
FIGURE 4.5
6. Remove auger drive belt from drive disc pulley.
Route auger belt through drive system in between
rubber drive tire and drive disc.
7. Route new auger drive belt through drive
system. NOTE: New belt has to be routed in
between rubber drive tire and drive disc to position
it around auger pulley.
8. Reinstall wheel drive belt onto engine wheel
drive pulley. Make sure belt is also positioned in the
drive disc pulley groove.
9. Route auger drive belt around engine auger
drive pulley. Make sure belt is also positioned in the
drive disc pulley groove.
10. Position both belt guides to have a clearance of
1/8” from auger drive belt (when engaged) and
tighten securely.
11. Reinstall discharge chute, belt and drive system
covers and tighten screws securely.
12. Reinstall drive system cover plate.
13. See Sections 4.1.1. & 4.1.2. Auger Belt
Adjustment for new belt adjustment. Adjust belt as
described in these sections.
REMOVE DRIVE
SYSTEM COVER
LOOSEN
BELT
GUIDE
WHEEL DRIVE
BELT
LOOSEN
BELT GUIDE
DRIVE DISC
PULLEY
AUGER DRIVE BELT
16
Section 4 - REPAIR & ADJUSTMENTS
WARNING
Before attempting any adjustments, maintenance,
service, or repairs, stop engine and auger, always
remove key from ignition switch, remove spark plug
wire and secure wire away from spark plug. Before
tilting machine, drain all the fuel from fuel tank.
Allow engine to run, outdoors where fumes can be
safely dissipated, until all fuel is removed from
carburetor.
4.1.4. WHEEL DRIVE BELT REPLACEMENT
Inspect belt frequently for signs of excessive wear.
Visually check engine drive belt for cracking,
fraying, severed or belt strands exposed. NOTE:
Auger and Drive Belts are difficult to install. It may
be necessary to allow an authorized Snapper
Dealer to install these belts.
1. Remove belt cover. See Figure 4.2.
2. Remove discharge chute.
3. Loosen belt guide closest to the auger drive belt.
See Figure 4.6.
IMPORTANT: Wheel drive belt will have to be removed
from around engine drive pulley and engine shaft to
install auger drive belt.
4. Remove wheel drive belt from around engine
pulley. See Figure 4.6.
FIGURE 4.6
5. Tilt machine forward to gain access to drive
system area. Secure machine in the tilted position
to prevent tipping over. Remove drive system cover
plate. See Figure 4.7.
FIGURE 4.7
6. Remove wheel drive belt from drive disc pulley.
Route wheel belt through drive system in between
rubber drive tire and drive disc.
7. Route new wheel drive belt through drive
system. NOTE: New belt has to be routed in
between rubber drive tire and drive disc to position it
around auger pulley.
8. Reinstall wheel drive belt onto engine wheel
drive pulley. Make sure belt is also positioned in the
drive disc pulley groove.
9. Position belt guide to have a clearance of 1/8”
from auger drive belt and tighten securely.
10. Reinstall discharge chute, belt and drive system
covers and tighten screws securely.
11. Reinstall drive system cover plate.
12. See Sections 4.1.1. & 4.1.2. Auger Belt
Adjustment for new belt adjustment. Adjust belt as
described in these sections.
LOOSEN
BELT
GUIDE
WHEEL DRIVE
BELT
LOOSEN
BELT GUIDE
DRIVE DISC
PULLEY
AUGER DRIVE BELT
REMOVE DRIVE
SYSTEM COVER
17
Section 4 - REPAIR & ADJUSTMENTS
4.1.5. GROUND SPEED ADJUSTMENT
NOTE: It is recommended to remove the drive system
cover and check rubber drive engagement with drive
disc when adjusting ground speed.
1. Tilt machine forward to gain access to drive system
area. Secure machine in the tilted position to prevent
tipping over. Remove drive system cover plate. See
Figure 4.7.
2. Loosen the top screw that connects the shift rod to
the shift hub. See Figure 4.8.
3. Move shift rod clockwise to obtain more ground
speed or counter clockwise for less ground speed.
Retighten top screw after adjustment. See Figure 4.8.
FIGURE 4.8
4. Check drive system to insure the rubber drive
tire has full contact with drive disc. Shift through all
speeds and note the position of rubber drive tire on
the drive disc. See Figure 4.9.
FIGURE 4.9
4.1.6. SKID SHOE ADJUSTMENT
NOTE: It is recommended to raise the auger
housing when clearing rough or graveled surfaces.
To raise auger the skid shoes should be lowered.
1. Tilt machine up and place a wooden block under
auger housing.
2. Loosen bolts on both skid shoes. Move shoes
down to raise auger housing or move skid shoes up
to lower auger housing. See Figure 4.10.
FIGURE 4.10
4.1.7. AUGER SHEAR BOLT REPLACEMENT
IMPORTANT: If engine is operating correctly and
auger/impeller drive belt is not damaged or severed,
but the auger/impeller does not rotate it is possibly
the auger shaft shear bolt.
1. Remove shear bolt and nut from auger. Discard
old shear bolt and nut. DO NOT reuse bolt or nut
under any circumstances. Always replace existing
hardware with genuine Snapper new replacement
shear bolts and nuts. DO NOT substitute these
shear bolts and nuts with hardware other than what
is specified as auger/impeller and engine damage
can result.
2. Install new shear bolts and nuts. Tighten to 5 to
10 ft. lb. of torque. See Figure 4.11.
FIGURE 4.11
SKID SHOE
SCRAPER
BLADE
BLOCK
UP FOR SMOOTH
PAVED SURFACES
DOWN FOR ROUGH
GRAVELED SURFACES
COUNTERCLOCKWISE
CLOCKWISE
SHIFT
HUB
LOOSEN TOP SCREW
AND MOVE SHIFT HUB
CLOCKWISE OR
COUNTERCLOCKWISE TO
ADJUST GROUND SPEED
TIRE IS ON
EDGE IN 4 th
POSITION
REVERSE 1st 4th
DRIVE
DISC
TIRE IS ON EDGE OF
HOLE IN REVERSE
AND 1
st
POSITION
SHEAR
BOLT
AUGER
18
Section 4 - REPAIR & ADJUSTMENTS
4.1.8. SINGLE HANDLE CONTROL ADJUSTMENT
(7 HP Models Only)
IMPORTANT: Standing in the operator’s position, the
left handle bar lever is for wheel drive engagement and
disengagement. The right handle bar lever is for
auger/impeller engagement and disengagement. Hold
both levers down to handle bar for engagement and
release levers for disengagement. When both levers
are pressed down to the handle bar at the same time,
the operator can release the right hand lever and the
right lever will remain engaged as long as the left hand
lever is held down to handle bar. Release the left hand
lever and both levers will disengage.
1. Hold the wheel drive control lever down against the
handle. See Figure 4.12.
2. Check position of the cam lock. It must align with
the adjusting line located on the cam lock bracket.
3. To adjust, loosen the nuts on the cable guide
support bracket and move the bracket in or out until
the cam lock aligns with the adjusting line. Retighten
nuts.
4. Hold the wheel drive control lever down to the
handle bar, at the same time press the auger/impeller
control lever down to the handle bar and hold in
position.
5. Check the position of the cable ferrule in relation to
the cam lock. The ferrule must be located 1/16” (.060)
above the hook of the cam lock. To adjust, loosen the
three nuts that secure the cam lock bracket. Slide
bracket up or down until correct measurement is
achieved. Retighten nuts securely. See Figure 4.12.
FIGURE 4.12
HOLD DOWN
HOLD DOWN
TRACTION CLUTCH
CONTROL LEVER BLOWER CLUTCH
CONTROL LEVER
(L.H. SIDE) (R.H. SIDE)
CABLE
CAM LOCK
CABLE FERRULE
.060
(1/16”)
CABLE
CAM LOCK
HOOK
ADJUSTMENT LINE
(ON BRACKET)
DOWN
UP
CAM LOCK
BRACKET
IN
OUT
CABLE
GUIDE
CABLE GUIDE
SUPPORT
BRACKET
19
Section 4 - REPAIR & ADJUSTMENTS
WARNING
Before attempting any adjustments, maintenance,
service, or repairs, stop engine and auger, always
remove key from ignition switch, remove spark plug
wire and secure wire away from spark plug. Before
tilting machine, drain all the fuel from fuel tank.
Allow engine to run, outdoors where fumes can be
safely dissipated, until all fuel is removed from
carburetor.
4.1.9. CHUTE CRANK ADJUSTMENT
1. Loosen adjustment bolt. Move crank worm
bracket away from ring gear slightly. NOTE: The
worm gear should always maintain full contact with
ring gear after adjustment. Retighten adjustment
bolt. If crank still does not operate satisfactorily,
lubricate worm gear and ring gear with grease.
See Figure 4.13.
FIGURE 4.13
4.1.10. RUBBER DRIVE DISC REPLACEMENT
1. Tilt machine forward to gain access to drive
system area. Secure machine in the tilted position
to prevent tipping over. Remove drive system cover
plate. See Figure 4.5.
2. Remove the five bolts that secure rubber drive disc
to the drive hub. Remove drive tire. See Figure 4.14.
3. Install new rubber drive disc. Reinstall the five
bolts. Torque to 25 to 40 in. lbs. See Figure 4.14.
FIGURE 4.14
CHUTE GEAR
RING
CHUTE
CRANK
ROD
WORM
BRACKET
MOUNTING
BOLT
ADJUSTMENT
BOLT
CHAIN CASE
ASSEMBLY
RETAINING
SCREW(S)
DISC
RETAINER
RUBBER
DISC
20
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION
Engine Will Not Start
1. Fuel tank empty. 1. Fill fuel tank with fresh fuel/oil mix.
Using Recoil Starter 2. Engine needs choking and priming. 2. Move choke control to “CHOKE” position.
Push primer bulb three times.
3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.
4. Fuel shut off valve closed. 4. Move fuel shut off valve to the on position.
Engine Will Not Start
Using Electric Starter 1. Power extension cord not plugged into machine or
120 Volt outlet for U.S.A. or 230 Volt for Europe. 1. Plug power extension cord into machine & into
120 Volt outlet for U.S.A. or 230 Volt for Europe..
2. Power extension cord damaged. 2. Discard damaged power extension cord
3. Starter switch damaged or faulty. 3. Replace starter switch.
Engine Stalls or Stops
1. Water, debris or stale fuel in fuel system. 1. Drain and clean fuel system.
After Running 2. Choke control in the “CHOKE” position. 2. Move choke control to “OFF” position.
3. Fuel tank empty. 3. Fill with fuel to proper level.
4. Air intake clogged with snow or debris. 4. Unclog air intake.
5. Spark plug defective or gap set improperly. 5. Service spark plug.
Engine Loses Power 1. Engine lubrication oil level is low. 1. Add oil to the engine to full level.
2. Spark plug faulty. 2. Service spark plug.
3. Water, debris or stale fuel in fuel system. 3. Drain and clean fuel system.
Excessive Vibration 1. Damaged, out of balance or bent auger. 1. Service auger.
2. Loose engine or auger components. 2. Service and tighten loose components.
3. Bent or loose Idler pulley 3. Tighten or replace pulley.
4. Cracked, severed or frayed belt 4. Replace belt.
Poor Snow 1. Clogged discharge chute. 1. Stop engine and unclog discharge chute.
Discharging 2. Damaged or bent auger or components. 2. Service auger or components.
3. Cracked, severed or frayed belt. 3. Replace belt.
4. Belt tension out of adjustment. 4. Adjust belt tension.
5. Insufficient lubrication in auger bearings. 5. Lubricate all bearings as specified in manuals.
SERVICE SCHEDULE
ITEM SERVICE PERFORMED
REF. EACH
USE 5
HRS 25
HRS 50
HRS 100
HRS EACH
SEASON
Spark Plug Replace Engine Manual.
X
Engine Oil Check Oil Level Engine Manual. X
Initial Oil Change Engine Manual. X
Periodic Oil Change Engine Manual X
Engine Cooling
System Clean Shroud & Fins Engine Manual X
Drive Belts Check For Adjustment,
Wear and Tension Page 12-14 X X X
Auger &
Impeller Check For Damage &
Lubrication Page 12 X X
Tires Check Air Pressure Page 7 X
21
3 YEAR LIMITED WARRANTY
For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through
any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found
upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
For ninety (90) days from purchase date for the original purchaser's commercial, rental, or other non-residential use,
SNAPPER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon
examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for
replacement under this warranty must be paid by the purchaser.
This warranty does not apply to engines and their components, and batteries, as these items are warranted separately.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper lubrication,
normal wear, or other cause beyond the control of SNAPPER. This warranty does not cover any machine or component
part that has been altered or modified changing safety, performance, or durability.
Batteries have a one (1) year prorated warranty period with free replacement if required during the first ninety (90) days
from the original purchase date. SNAPPER will not be responsible for any installation cost incurred. The battery warranty
only covers original equipment batteries and does not cover damage to the battery or machine caused by neglect or
abuse, destruction by fire, explosion, freezing, overcharging, improper maintenance, or use of improper electrolyte.
There is no other express warranty.
DISCLAIMER OF WARRANTY
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to three
(3) years from purchase date for the original purchaser's residential or other non-commercial use, and ninety
(90) days from purchase for the original purchaser's commercial, rental or other non-residential use, and to the
extent permitted by law, any and all implied warranties are excluded. This is the exclusive remedy. Liabilities for
consequential damages, under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
WARNING: THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE
SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER
ASSOCIATED WITH THE USE OF SUCH PARTS.
IMPORTANT: Please fill out the attached SNAPPER Product Registration Card immediately and mail to:
Snapper’s Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253
22
NOTES
23
NOTES
24
Safety Instructions & Operator’s Manual for
EUROPEAN
TWO STAGE
INTERMEDIATE FRAME
SNOW THROWER
SERIES 3
WARNING: The engine exhaust from this product contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive harm.
COPYRIGHT © 2000
SNAPPER INC.
ALL RIGHTS RESERVED
INSTRUCTION No. 7-3334 (I.R. 02/14/00)

Navigation menu