Solectek 58WAN3 Wireless Network Transceiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1063580
Application ID	WnY9bsVTVqmvgzjAq3nJDA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	66.37kB (829666 bits)
Date Submitted	2009-02-02 00:00:00
Date Available	2009-02-04 00:00:00
Creation Date	2009-01-19 16:14:12
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2009-01-19 16:14:12
Document Title	Microsoft Word - Skyway Excel User Guide 1514001 FCC v1.4.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	alaudani

1. Introduction
Congratulations on your purchase of Solectek’s SkyWay Excel Series PTP Radio
System, a feature rich, best-in-class wireless solution. This User’s Guide will
describe the operation of your SKYWAY unit in detail.
SYSTEM FEATURES
•
SkyWay® Excel PTP Series
•
•
•
•
User’s Guide
v1.4
•
Field proven, MIMO- OFDM modulation allowing high capacity, near
line-of-sight deployment and strong immunity to multi-path.
Power over Ethernet (PoE) for simplified cable routing.
Integrated antenna/radio simplifies installation and eliminates lossy RF
coax runs.
Frame aggregation for enhanced data throughput.
Line speed QoS packet inspection prioritizes latency sensitive, realtime data.
Intuitive Web based user interface and Telnet CLI.
KIT CONTENTS
•
•
•
•
•
•
•
•
•
SkyWay Radio (2)
External antennas & RF Cables (2 sets)1
+48VDC AC-DC Power Supply. (2)
Power over Ethernet (PoE) injector. (2)
Pre-assembled, two-axis mast mounting kit. (2)
Cat5 weatherproofing feedthrough. (2)
Coax/grommet seals (16)
Documentation CD
Warranty and Compliance Card.
NOTE: The requisite Cat5 Ethernet cables are not included in the
package. Please contact Solectek for information on available outdoor grade
shielded Ethernet cables.
Management Platform Requirements
Part Number: 1514001
Copyright 2008, Solectek Corp. All rights reserved.
a)
For GUI management: Pentium IV (or later) computer; Windows XP
SP2; Internet Explorer v7.0, or later.
b)
For SNMP management: SNMP v1 or v2c compatible SNMP manager,
running on appropriate PC/Server platform.
For external antenna model, only
2. Installation Outline
This section summarizes the steps needed to properly configure and install
the SkyWay Excel Radio. As the background and guidelines for much of
the radio installation process are well covered in many in-depth
publications and training classes, only those steps that uniquely relate to
the SkyWay product are covered in this User Guide.
A. System Design
RF Design and Site Survey
IP Network Design
B. Unit Preparation
Unit connection (Section 3)
Initial Configuration (Sections 4-6)
Bench testing (Section 7)
3. System Connection
A. PORT DESCRIPTIONS
The SkyWay Excel has the following access ports:
•
(1) Fast Ethernet + Power Connector: RJ45 jack
•
(2) RF Ports: N type, female (connectorized unit only)
The RJ45 connector is accessed at the bottom of the unit, through a multipiece waterproofing feedthrough.
If included, the two RF Ports are accessed on the top of the unit.
C. Site Preparation
Selection of unit mounting location
Cable routing
Preparation of mast and other supporting structures
D. Physical Installation
Mounting (Section 8)
Antenna alignment (Section 9)
E. Verification
Link status + metrics (Section 10)
Ping connectivity
Performance testing
Reliability monitoring
F. Optimization
RF channel tuning
Data rate tuning (see Product ‘Range Guide’)
QoS (Section 11)
Unit Top
B. CONNECTING THE SKYWAY UNIT
Using the appropriate diagram below as a guide, cable your SkyWay test
system. Connect your PC to the POE injector using (a) crossover Ethernet
cable or (b) straight cable and a hub/switch.
G. Management + Maintenance
VLAN (Section 12)
Telnet (Section 13)
SNMP (Section 14)
Network Time (Section 15)
Password Management (Section 16)
Software upgrades (Section 17)
Reboot (Section 18)
H. Troubleshooting
Event Log (Section 19-20)
Diagnostics (Section 21)
LOG INTO THE HTTP MANAGEMENT SYSTEM
C.
•
Open networking properties in your Windows OS. Find the TCP/IP
setup window of your wired Ethernet adapter. Set the IP addresses to
the following values.
Ethernet’s IP Address:
Subnet Mask:
•
•
192.168.1.1
255.255.255.0
Open a Web Browser on the Test PC
At the URL line, type in the following: http://192.168.1.100 to access
the login prompt:
•
The username is admin and the default password is admin. Click
OK and you will see the Main Status screen as shown:
4. Initial Configuration
A. IP Configuration
Navigate to Configuration -> Basic to access the Basic Configuration screen:
System Name This is a description of the unit used to simplify the
identification of a particular radio in the wireless network. This parameter is
not related to the identification of the unit on your wired local area network.
For security purposes, the System Name is not broadcast across the RF link.
LAN IP Configuration
IP Address: IP address of the local unit.
Subnet Mask: Subnet mask of the local unit.
Default Gateway: Default gateway for the local unit.
B. Wireless Configuration
Navigate to Configuration -> Wireless to access the Wireless Configuration
screen:
Note that the maximum link distance at 20 and 40 MHz bandwidth is 32 and 16
miles respectively.
Streams The power of MIMO technology rests on the ability to define the
number of data streams that are carried across the multiple RF links. At all
times, the SkyWay link utilizes a 2x2 dual-chain MIMO format where 2 RF
transmit and 2 RF receive chains are enabled and active. However, these dual
chains can be used to carry 1 or 2 data streams.
In a 2 stream configuration, unique data is carried across each RF chain,
thereby greatly increasing the amount of data capacity over a non-MIMO
system. The 100 Mbps capability of the product requires that 2 streams
operation be configured.
In contrast, when increased link robustness and noise immunity is desired,
MIMO can be used in a 1 stream configuration. In this scenario, the same
information is carried across both RF chains, increasing the reliability of
reception.
It is recommended, but not required, that both Master and Slave units share
the same Modulation and Stream settings.
ESSID
The wireless network name assigned to this PTP network.
Transmit Power This parameter sets the RF output power of the radio.
Increasing this value will extend the range of the PTP system. However, the
maximum available power is limited by the country of operation.
For example, in the US, the maximum operating power is limited to 23 dBm.
Frequency Allows selection of the center frequency of the RF link, based on
the region of operation and operating bandwidth. The Frequency parameter is
available on Master PTP unit only. On a Slave unit, the radio will search across
the available channels in order to find the Master.
A sample frequency list is as follows:
Frequency
5745 MHz
5765 MHz
5785 MHz
5805 MHz
Bandwidth
20 MHz
20 MHz
20 MHz
20 MHz
Both Master and Slave must share the same Bandwidth setting.
Link Distance Should be set to the actual link distance. This parameter is
used to optimize the performance of the SkyWay protocol across long links.
5. Security
6. Access Control
Navigate to Configuration -> Security to access the Security Configuration
screen:
In addition to the formal security methods detailed in the previous section, a
second, independent access control layer is available.
This Layer2 access control system requires that the Master be programmed
with the MAC address of the Slave.
Navigate to Configuration -> ACL to access the following screen:
Slave’s MAC: This is the hardware RF MAC address of the client unit in
question. This MAC address can be found on the client unit’s user interface or
on the rear label. The correct address must be used to establish an RF link with
the base.
Three data encryption options are available: Open, AES and Radius. All units
on a wireless network must share the same security settings.
Open: Removes all encryption and formal authentication methods. Note that
even with an Open setting, there is still a MAC address based Access Control
system which provides a basic level of security. (See next section)
AES:
Provides
authentication.
128-bit
AES
data
encryption
with
passphrase
Slave’s Description: Type in any description that will easily identify the peer
with the above MAC address. This is an optional field for your convenience only
and has no effect on the operation of the unit.
Click Add after typing in MAC address and Description. Note that the slave unit
is in the Master’s access list and is shown on the bottom half of the screen.
based
Radius: In addition to AES encryption, this option adds Radius/802.1x
authentication capability compatible with all MS-CHAPv2/PEAP authentication
servers.
7. Benchtesting
8. Physical Installation
Before mounting units into their final location, it is recommended that the
system be benchtested to ensure settings are correct. The following benchtest
steps are suggested:
A. INTRODUCTION
Setup. Each radio should be connected and configured per the previous
Sections, with a laptop or PC connected to each radio directly (or through a
hub/switch). Be sure that Access Control MAC addresses are correct and that
units share the same bandwidth, data rate and security settings.
It is also important to have identified and prepared the antenna, RF coax and
Cat5 solutions that will be used in the intended application
Positioning. It is important to remember that the Skyway radio and antenna
system generate and transmit a great deal of RF power. During benchtesting in
an average sized room, the antennas should not be pointed directly at each
other. Instead, rotate the unit 90 degrees away from each other. Fine tune
the antenna position so that the Local RSSI is between -30 and -60 dBm.
Testing. If the system has been properly configured, the radios will begin
communicating immediately. The following steps are recommended to verify
operation:
•
Link State. On the Main Status screen, verify that the RF Link State is
Green (connected).
•
Local ping. From each laptop/PC be sure a ping to the local radio is
successful.
•
Link ping. Now ping from one laptop/PC to the other laptop/PC. This
will verify the end-to-end link.
•
Throughput test.
Using Qcheck, Iperf or equivalent throughput
measurement utility, verify system performance.
Your SkyWay radio is designed with a flexible, multi-axis mounting system.
The radio can be mast, tower, pole or wall mounted using the appropriate
hardware. After determining the best location for your radio, installation can
begin. Please refer to Solectek’s RF Site Design Guide on Solectek’s website
(www.solectek.com) for more information about choosing an ideal radio
location.
To mount a SkyWay radio, both the mast mounting kit and Ethernet cable
feedthrough need to be correctly assembled. The recommended approach
consists of 3 steps, detailed in the following sections:
1.
2.
3.
Ethernet cable / feedthrough assembly
Bracket preparation
Mounting
With the exception of the CAT5 cable, all parts and hardware described in the
following sections are included with your SkyWay radio.
B. ETHERNET CABLE / FEEDTHROUGH ASSEMBLY
Only a single Ethernet cable is needed to connect the Skyway radio to the
indoor PoE Injector. Since the cable is exposed to the outdoor elements (heat,
moisture, and UV light), only outdoor rated, shielded Cat5 Ethernet cable
should be used. To ensure all-weather operation, the weatherproofing cable
feedthrough (also known as grommet or gland) must be properly assembled
onto the Ethernet cable and radio.
The following diagram depicts each of the feed-through parts:
Notes:
(a) Keep in mind that the Skyway Excel data rates stress the performance of a
PC, OS and IP stack. To ensure that the test equipment is not the performance
bottleneck, testing with a direct connection between PCs is strongly
recommended.
(b) Using a single FTP session on a typical Windows/Intel machine is not
adequate to accurately measure throughput.
The following steps must be followed to make sure that the feedthrough is
assembled correctly:
1.
2.
3.
Remove the Compression Nut and slip it over the Ethernet CAT5 cable as
shown above.
Slip the Compression Gasket Insert over the Ethernet CAT5 cable
Feed the Ethernet CAT5 Cable through the Feedthrough Body (pre-installed
on the enclosure at the factory) and insert the RJ-45 connector to the female
connector inside the enclosure.
Note: the total combined length of the Ethernet cables between the radio and
your network access device (hub/switch/PC) must not exceed 300 feet.
Note: Once mounted in a permanent location, additional weatherproofing tape
(included) should be used to further enhance durability.
Note: In order to maintain FCC compliance, the use of shielded CAT5 cable is
required.
C. BRACKET PREPARATION
The SkyWay mounting bracket is pre-assembled at the factory for ease of
installation.
4.
Slide the Compression Gasket Insert into the Compression Gasket, as
shown above. Make sure to slide the Insert fully, such that the two parts are
evenly aligned.
5.
Install the Compression Nut and hand tighten until the cable resists slipping
when gently pushed or pulled. Lightly wrench-tighten, being careful not to
overtorque the Compression Nut.
The unit with properly installed feedthrough appears as follows:
Once the jaws are oriented appropriately, the two remaining bolts are used to
tighten the mounting kit jaws around the pole/mast.
Wall Mount: The larger, integrated jaw has (4) corner through-holes which
accommodate either M5 or #10 screws/bolts (not included) to mount the
system to a wall or soffit. In such a mounting configuration, the smaller jaw,
and (2) jaw bolts are not used.
Using the supplied Bolt/Nut/Washer, attach the bracket tab to the SkyWay
enclosure ear, as shown above.
Moderately tighten all bolts to prevent
inadvertent movement during the installation.
D. MOUNTING
The final installation step involves mounting your SkyWay radio to an outdoor
mast or wall.
Mast Mount: The mounting jaws can accommodate mast diameters from
0.75” – 3.0”. Note that the smaller jaw piece can be reversed. Small diameter
masts require the use of the jaw configuration shown in the first picture, below.
Large diameter masts must use the configuration shown in the second picture.
9. Antenna Alignment
10. Verifying Operation
SkyWay Excel contains several tools to aid with the antenna alignment process:
The basic status of the unit can be viewed in the Main Status screen:
Audible Alignment: The radio produces an audible beep allowing antenna
alignment without the need for additional monitoring hardware.
Beeping will begin once an RF link has been established, regardless of quality.
It is useful to reduce the RF Data rate setting to its lowest value during the
antenna alignment procedure to maximize the system’s link capture
envelope/angle.
Beep rate will increase as a function of RSSI; a higher value will cause a faster
beep rate. To assist with both coarse and fine tuning, the beep rate is NOT a
simple function of RSSI value. Rather, the rate will continue to increase as long
as adjustments deliver an improved RSSI.
As soon as any degradation
(alignment ‘overshoot’) is detected, the beep rate quickly falls, regardless of
the amount of reduction. Thus, the system is useful for both coarse and fine
tuning of the antenna position.
To ensure the system will deliver adequate link reliability, it is recommended
that the operator verify the numerical RSSI following antenna alignment, rather
than relying solely upon the audible beep rate.
The audible function is enabled for the first 30 minutes of operation following a
power cycle.
Alignment Page: An alternative tool to assist with antenna alignment is the
Antenna Alignment page. Navigate to Installation -> Antenna Alignment to
display the following page:
This screen updates periodically and thus displays current field values.
Navigate to the Configuration screen if setting changes are necessary.
On this page is a dynamic display of the RF link state and local RSSI, in both
numerical and graphical format. In addition to displaying current RSSI, the bar
graph format has an auto-scale function which tracks the minimum and
maximum achieved RSSI values since power-up.
Three noteworthy items:
Up Time The elapsed time that the unit has been running since the last reboot
or power cycle.
MAC Address The MAC address of the local unit.
10
RF Port Link State The link state has two values.
The RF Port (navigate to the details button on the Main Status screen next to
each client’s description) also has its own detailed screen:
Green – An RF link has been established
Red – an RF link is NOT established.
Each of the ports also has its own, detailed status screen. For the Ethernet Port
status, navigate to the details button located on the far right side. The screen
below is typical:
MTU Size The maximum datagram size that the system is able to transmit.
Note that this refers to Ethernet payload not total Ethernet frame size.
State: There are two states, Green – Port Up. Red – Port Down.
Total Frames: total number of frames received and transmitted by the
Ethernet port.
Total Octets: total number of octets (bytes) received and transmitted by the
Ethernet port.
11
Key fields for this screen include:
11. Quality of Service (QoS)
Master / Slave MAC: The RF port MAC address of the Master and Slave unit.
Link State: Green if a link is established and Red if not.
Local RSSI: Receive Signal Strength as received by unit currently being
managed. For reliable link operation, RSSI should be a minimum of 6-10 dB
above the radio’s receive sensitivity.
Total Frames: Total number of aggregated RF data frames received and sent
by the unit. Note: this number should not be expected to match the Ethernet
frames count. Packet framing, aggregation and QoS operations will all affect
the manner in which data is transported from Ethernet to RF port.
For the transport of real-time data, such as VoIP or streaming video, a QoS
system provides end-to-end prioritization of pre-tagged Ethernet frames.
The QoS system relies upon the originating network device/appliance to tag
frames using an 802.1p VLAN priority tag
As a frame enters the Radio, a line speed tag inspection is performed and
frames are prioritized as follows:
a.
A priority queuing method assigns tagged frames to one of the 4 priority
queues, allowing higher priority data to then be pushed onto the RF stack
ahead of lower priority frames.
Tagged frames are assigned to queues
based on the following tag matrix:
Data Packets: Total number of data packets prior to aggregation, on the
transmit side, and following de-aggregation, on the receive side.
Voice
Video
Normal
Background
0x0
0x4
0x1
0x5
Receive Errors: Total number of errored frames received by the local unit.
Note: RF Frames which are significantly damaged can not be accurately
attributed to a paired radio and will not affect this count.
Transmit Errors: Total number of frames transmitted by the local radio that
were not successfully acknowledged by the remote radio.
Errors of this type can be attributed to two causes: (a) Data packet not
received by remote radio, or (b) Acknowledgement packet not received by local
radio.
Tag Method
802.1p
It is often instructive to compare RX and TX error counts so that RF
impairments can be isolated to the appropriate link direction and radio.
b.
0x3
0x7
0x2
0x6
Once on the RF stack, the RF MAC gives prioritized frames early access to
the ‘air’ resulting in the frames being delivered sooner to the receiving
radio.
Notes:
•
•
•
The QoS system does not add or alter priority tags
QoS is always ‘enabled.’
For best results, all network devices (switches, routers, gateways)
between source and destination devices should be QoS aware.
12
12. VLAN Access
13. Telnet
A VLAN configuration section is available under Configuration -> Advanced.
Using the SkyWay radio’s IP address, the system can be managed using a
Telnet connection.
Units will bridge VLAN frames transparently at all times. That is, all frames
tagged with VLAN IDs will be recognized and passed though the system. The
unit will NOT tag or strip VLAN ID’s.
Access login and password are the same for the Telnet session as for the HTTP
GUI.
The VLAN feature option affects the accessibility of the Radio’s user interface
by Management computers from within a VLAN.
Sessions can be initiated from both the Ethernet and RF side of the Network,
and multiple sessions are permitted.
Enable/Disable. If access to the Web GUI will be from a PC within a VLAN,
then this feature should be Enabled. If access is from a PC outside of a VLAN,
then this feature should be disabled.
Note: the ‘savecfg’ command must be used to save Telnet configuration
changes to non-volatile memory.
VLAN ID: The ID should be set to match the VLAN ID used on your
management PC. This setting does not affect any other VLANs running on your
network or the ability to pass VLAN traffic.
See Appendix B for a complete Telnet command set, syntax and usage.
13
14. SNMP
The SkyWay management system includes support for SNMP v1 and v2c via
standard and private MIB tables.
Navigate to Management -> SNMP access the SNMP Configuration screen:
SNMP Enable: For security purposes, the SNMP engine can be disabled, if not
used.
Community Names and Trap Manager IP Address fields should be entered
based on the configuration of your SNMP Manager software.
Please refer to the User Manual of your SNMP Manager software for detailed
information on establishing and managing units via SNMP.
For further questions and to obtain Solectek’s private MIB, please contact
technical support.
15. Network Time
Using the NTP protocol, the SkyWay Excel radio can be time synchronized to
other network devices.
To setup this feature, navigate to Configuration -> Advanced to access the
Date and Time feature configuration:
To time synchronize the radio, the NTP server IP address must be established
and the ‘sync’ button pressed. If connection is successful, the local time/date
will be updated to match NTP time.
An NTP resync will occur automatically twice per day.
If the NTP server is off-line, time is still kept locally on the radio. However, a
reboot of the unit will blank the time. A re-connection to the NTP server or
manual re-configuration of the time is required to correct the time/date.
Time zone information must be entered manually as a fixed offset from UTC.
Once entered, this information is stored in non-volatile local memory and does
not need to be re-entered.
All changes should be followed by a ‘Submit’ to make active.
14
16. Password Management
> Login: recover
> Password: (default)
Navigate to Management -> Password to access the Login configuration
screen:
Once logged in as ‘recover’, the hint will be given. Upon successful answer, the
admin password can then be changed.
It is strongly advised that the admin password, and hint answer
be recorded and stored in a secure location.
Notes:
(a) Password & hint fields are case sensitive and no spaces are allowed.
(b) Password & hint can be up to 16 characters in length.
(c) Legal characters are: all alphanumerics, plus the following symbols:
@ (at sign) _ (underscore) - (dash) . (period)
Enter New Password: Enter the new password.
Confirm Password: Re-enter the new password for confirmation.
At the time of the first password change, a password ‘hint’ prompt will be
displayed.
Once established, this hint answer can be used to reset the admin password, if
it has been forgotten, via the ‘recover’ Telnet login, as follows:
15
17. Upgrading the Software
There may be newer software releases from Solectek periodically. The latest
version will be posted on Solectek’s website and available from Solectek
Technical Support.
The software is comprised of three sections: Firmware, Kernel and Bootloader.
However, only a single upgrade operation is required to bring all three up to the
latest revision.
Upgrading the software will not affect the system configuration, but does
require a short period of system downtime to complete the process.
NOTE: A PC based FTP server program running on a locally connected
PC is required to complete the following upgrade procedure. Solectek
recommends FileZilla, a free, open-source FTP server program available via
http://filezilla-project.org/
Once the FTP server is installed, the following procedure should be followed:
1.
2.
3.
4.
5.
6.
Copy .zip software release package from Solectek website or Technical
Support to FTP Server desktop.
Unzip / extract files to any convenient directory.
Navigate into the extracted fileset to reach the SetupFirmware.exe tool.
Launch tool by double-clicking on tool icon; the following screen will be
displayed:
Press the ‘Browse’ button and select the local FTP server Home Directory.
Press the ‘Start’ button. This begins a file copy operation and ensures that
all upgrade files and folders are properly moved into the FTP directory.
7.
On the Radio management GUI, navigate to Management -> Upgrade to
access the Upgrade screen (see sample below).
8. Enter the FTP Server IP Address, Username and Password information as
requested.
9. Enter the three digit software version to be loaded onto the Radio. Format
will be x.y.0 (e.g – 1.3.0).
10. Press the ‘Upgrade’ button to begin the file transfer process.
11. Once complete, the unit must be rebooted for the upgrade to take effect.
Do not power down or unplug the unit during the upgrade
process.
16
18. System Reboot
Navigate to Reboot to access the System Reboot function:
19. Event Log
The Event Log displays all major events that may be noteworthy for the system
administrator for both monitoring and troubleshooting purposes.
Navigate to Status -> Event Log to access the Event Log Screen:
Click on the Reboot button to reset/reboot. The reboot process will take
approximately 25 seconds. Once the rebooting is done, you can use the Click
Here button below to access the user interface again.
There are three categories of events:
Notice: This is informational in monitoring the operation of the unit. A Notice
entry is part of the normal operation.
WARN: This may indicate something wrong with the unit or operation. For
example, downing of the RF port may be due to malfunction or the user
intervention (power off).
ERROR: This is indicative of abnormal operating conditions.
17
20. Log/Configuration Transfer
For diagnostic purposes, the Event Log and System Configuration database can
be transferred from the Radio to a local PC via FTP.
21. Diagnostics
For diagnostics, navigate to Diagnostics => Time/Ping menu to view the
following:
Navigate to Diagnostics -> File Upload to access the following screen:
FTP Server IP Address: Local FTP server address.
Password: Password used to login onto the upgrade FTP server.
The ping diagnostics tool on the unit can be used to isolate the troubleshooting
event to the wireless link only, not involving other network elements such as
switches and host computers. You can ping the remote unit from the unit you
are accessing via the user interface.
File Directory: Location on Local FTP server to save Event and Configuration
files.
Destination Addr: The IP address of the device to be pinged.
User Name: User name used to login onto the FTP server.
Packet Size: The size of the ping packets to be sent (in bytes).
Packet Count: The number of packets to be sent to the destination IP address.
Click on the Start button to initiate the ping session. Click Stop to terminate it.
18
Appendix A: Factory Defaults
WIRELESS
Radio Spectrum bandwidth
Frequency (Master-only)
RF Power
Modulation
Streams
Distance
ESSID
Security
20 MHz
Region Specific
17 dBm
QAM16-1/2
16 miles
MY_ESSID_1
Clear
LAN
IP Address / Mask
IP Gateway
Login Name / Password
Ethernet Port
192.168.1.100 / 255.255.255.0
192.168.1.1
admin / admin
Auto
19
Appendix B: Telnet Commands
Command
Category
R/W
Default
audioalign
Admin
RW
1800 secs
date
Admin
RW
Usage
Set Audio Antenna Alignment duration in
seconds
Duration 0 disables the beeping.
date [-u]... [MMDDhhmmYYYY
Display or set current date
Options:
-u
date
default
ftpaddr
ftppass
ftpuser
log
name
ntpaddr
password
ping
Admin
Admin
Admin
Admin
Admin
Admin
Admin
Admin
Admin
RW
RW
RW
RW
RW
192.168.1.1
ftp
(blank)
192.168.1.1
admin
Description
set audioalign [duration_secs]
show audioalign
Apply the UTC time zone offset to the
default
set ftpaddr [a.b.c.d] show ftpaddr
set ftppass [password] show ftppass
set ftpuser [user] show ftpuser
show log
set name [name] show name
set ntpadd [a.b.c.d] show ntpaddr
password (prompts lead user for password change)
ping [OPTION]... Host
Restores system to factory defaults
Set remote ftp server IP address
Set remote ftp server password
Set remote ftp server username
Show Event Log
Set system name
Set NTP server address
Change admin password
Test network connectivity
Options:
-c CNT
Send only CNT pings
-s SIZE
Send SIZE data bytes in packets
(default=56)
-I iface/IP Use interface or IP address as source
-q
Quiet, only displays output at start
and when finished
reboot
savecfg
serialnum
snmp
Admin
Admin
Admin
Admin
RW
status
sysmode
Admin
Admin
RW
enabled
public – for all
strings
192.168.1.1 for trap
manager
PTP_SLAVE
reboot
savecfg
show serialnum
set snmp enable=[yes|no]
set snmp [read-community|rc]=[abcdef]
set snmp [write-community|wc]=[abcdef]
set snmp [trap-community|tc]=[abcdef]
set snmp [trap-manager|tm]=[a.b.c.d]
show snmp
Reboot system
Save configuration to permanent memory
Show system serial number
Set SNMP configuration parameters
status
show sysmode
set sysmode 
Show system status
Show / Set the PTP operating mode
20
tz
updatesw
Admin
Admin
RW
“+00:00”
tz [+hh:mm | -hh:mm]
updatesw [options] [swver]
Options:
upload
uptime
version
vlan
Admin
Admin
Admin
Admin
RW
disabled
vlanid
ethcfg
Admin
Network
RW
RW
auto
arp
Network
RW
-v -verbose output
-b -update uboot
-k -update kernel
-r -update rootfs
-h -use http
-i -ignore existing configuration
-f -force the update
upload [[config | syslog] [ []]]
uptime
version
vlan [enable | disable]
Upload files to remote server
Display current system uptime
Display current software version
Enable/Disable management via VLAN
set vlanid [vlan id] show vlanid
set ethcfg [auto-neg | 10baseT-HD | 10baseT-FD |
100baseTx-HD | 100baseTx-FD]
show ethcfg
Set VLAN ID for management channel
Set ethernet speed and duplex
arp [OPTION]
Manipulate the system ARP cache
Options:
-a
-s
-d
-v
-n
-i IF
-D
-A, -p AF
bridge
clear
gwaddr
ipaddr
ipmask
macaddrs
route
bw
chanplan
Network
Network
Network
Network
Network
Network
Network
RF
RF
RW
RW
RW
RW
counters
distance
essid
RF
RF
RF
RW
RW
192.168.1.1
192.168.1.100
255.255.255.0
20
Region
specific
16
MY_ESSID_1
Set/Show time zone
Download and install new system software
Display (all) hosts
Set new ARP entry
Delete a specified entry
Verbose
Don't resolve names
Network interface
Read [hwaddr] from given device
Protocol family
show bridge
clear
set gwaddr [a.b.c.d] show gwaddr
set ipaddr [a.b.c.d] show ipaddr
set ipmask [a.b.c.d] show ipmask
show macaddrs
show route
set bw [20 | 40] show bw
set chanplan [channel_plan]
Show Bridge Table
Clears all Ethernet & RF Port counters
Set default gateway IP address
Set IP address
Set IP netmask
Show Ethernet and RF MAC addresses
Show IP route table
Set RF bandwidth in MHz
Show current channel plan.
show counters
set distance [miles] show distance
set essid [essid] show essid
Show RF statistics
Set distance in miles
Set RF ESSID of wireless network
21
freq
RF
RW
Region
specific
mod
RF
RW
QAM16 ½
power
rssi
streams
RF
RF
RF
RW
RW
17
encrypt
Security
RW
open
psk_phrase
radius_pass
radius_secret
radius_timer
Security
Security
Security
Security
RW
RW
RW
RW
my-big-secret-01
abcd1234
my-big-secret-01
86400
set psk_phrase [phrase] show psk_phrase
set radius_pass [password] show radius_pass
set radius_secret [secret] show radius_secret
set radius_timer [period] show radius_timer
Set pre-shared key passphrase
Set Radius user password
Set Radius secret
Set Radius reauthentication period, in
Seconds
radius_user
exit
get
help
history
logout
set
show
Security
Usage
Usage
Usage
Usage
Usage
Usage
Usage
RW
wpa1@host.local
set radius_user [name] show radius_user
exit
get
help
history
logout
set ?
show
Set Radius client user name
Logout from Telnet session
Get commands
Show commands
Show command history
Logout from Telnet session
Set ? for commands
Show commands
set freq [frequency]
show freq
Set RF frequency in MHz
show mod
set mod 
Show Current Modulation
set power [rfpower] show power
show rssi
show streams
set streams <1 | 2 >
Set RF Transmit power, in dBm
Show Local Recv Signal Strength
Show / Set the number of MIMO data
streams
set encrypt [open | AES | radius]
show encrypt
Open: no authentication/encryption
AES: PSK authentication / AES encryption
Radius: 802.1x authentication / AES
encryption
22
Appendix C: Regulatory Information
1. FCC Radio Frequency Interference Statement
FCC ID: KA358WAN3
This device is certified to comply with Part 15 of Federal Communications
Commission (FCC) Rules. Operation is subject to the following two conditions:
1. It may not cause harmful interference.
2. It must accept any interference that may cause undesired operation.
Changes or modifications not expressly approved by Solectek could void the
user’s authority to operate the equipment.
2. U.S. Government Restricted Rights Legend
The Product is provided with Restricted Rights. Use, duplication, reproduction or
disclosure by the Government is subject to restrictions in subdivision (c)(1)(ii)
of the Rights in Technical Data and Computer Product clause at 252.227-7013
and in subparagraphs (a) through (d) of the Commercial Product-Restricted
Rights Clause at 52.227-19. Contractor/Manufacturer is Solectek, 6370 Nancy
Ridge Drive, Suite 109, San Diego, California.
3. Radio Transmission Notice
However, there is no guarantee that interference to radio communications will
not occur in a particular commercial installation. In case the device does cause
harmful interference with an authorized radio service, the user/ operator shall
promptly stop operating the device until harmful interference has been limited.
Solectek Corporation is not responsible for any radio or television interference
caused by unauthorized modification of this device or the substitution or
attachment of connecting cables and equipment other than specified by
Solectek Corporation. The correction of interference caused by such
unauthorized modification, substitution, or attachment will be the responsibility
of the user.
Warning:
The antennas used for this transmitter must be installed to provide a
separation distance of at least 100 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or
transmitter
This device has been designed to operate with the antennas listed
below, and having a maximum gain of 29 dBi. Antennas not included in
this list or having a gain greater than 29 dBi are strictly prohibited for
use with this device. The required antenna impedance is 50 ohms.
1. Pulse 10dBi RO5810NM (3) 5.8 GHz Radome Omni 10 dBi
This product is a low power (less than 1 Watt), OFDM radio system pre-set to
transmit and receive signals in the 5.725 – 5.850 GHz frequency band. This
product has been certified by the U.S. Federal Communications Commission for
use in the United States of America in that band. Other markings on the unit
label shall indicate regulatory compliance in other international areas.
2. ARC Wireless Solutions 5.15-5.875GHz 24/23dBi Dual Polarization
Panel Antenna
Any prospective user of this product outside the United States of America
should, prior to such use, contact the government department or other agency
responsible for assigning radio frequencies in the country in which use is
proposed to determine whether such department or agency has any objection
to operation of the product given current regulatory label markings on said
product, and whether there are any other local devices generating signals in
that band which might be expected to interfere with the operation of this
product.
The use of Antennas #2 and #3 above shall be restricted to Point-toPoint use only.
Solectek shall not be responsible for any operation of this product which is in
violation of local law, creates interference harmful to other local devices, or
results in a malfunction of this product caused by outside interference.
This device must be professionally installed and used in strict
accordance with the manufacturer's instructions. The installer shall be
responsible for ensuring that the proper antenna is employed so that
the limits in this part are not exceeded, including the requirements of
FCC Part 15.203
3. Laird HD Series High Performance Dish Antenna HDDA5W-29-DP 29dBi dual polarity (H and V)
This equipment has been tested and found comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
23
Information contained in this document is subject to change without
notice. Solectek Corporation shall not be liable for errors contained
herein or for incidental or consequential damage in connection with the
furnishing, performance, or use of this material. Reproduction,
adaptation, or translation without prior written permission is
prohibited, except as allowed under the copyright laws.
Solectek Corporation makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose.
NOTE: Changes or modifications not expressly approved by Solectek
could void the user’s authority to operate the equipment.
SkyWay and Solectek are registered trademarks of Solectek Corporation.
Windows is the trademark of Microsoft Corp.
Copyright 2009, Solectek Corp. All rights reserved.
24

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Title                           : Microsoft Word - Skyway Excel User Guide 1514001 FCC v1.4.doc
Creator                         : alaudani
Create Date                     : 2009:01:19 16:14:12-08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2009:01:19 16:14:12-08:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:9736a557-b905-4f04-a4c0-37aa417019eb
Instance ID                     : uuid:e121263b-fddd-4f8d-81a2-869696d0b871
Page Count                      : 24
Author                          : alaudani

EXIF Metadata provided by EXIF.tools