Somfy Systems SRS Solar Rain Sensor SRS-10 9019617 User Manual RTS rain sensor instr full FCC

Download:
Mirror Download [FCC.gov]
Document ID	2625797
Application ID	kNnskZ2hVWufgU09GJEGhw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.09kB (813679 bits)
Date Submitted	2015-05-27 00:00:00
Date Available	2015-05-27 00:00:00
Creation Date	2017-10-01 20:24:09
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-01 20:24:09
Document Title	RTS rain sensor instr full FCC.cdr
Document Creator	CorelDRAW X7
Document Author:	Glen Sanders

Instructions Somfy Solar Rain Sensor (SRS) - RTS
2.088”
[53.04]
2.590”
[65.79]
4.479”
[113.77]
IMPORTANT - Read the entire instructions and ensure the unit is charged before starting installation (see installation section)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions
- This device may not cause harmful interference and
- This device must accept any interference received, including interference that may cause undesired operation
Warning! Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment.
Mode and Threshold Selection - Awning
1 - Open the hatch by pressing the latch toward the hatch and pulling outward (Fig 1)
2 - Inside the hatch you will see the Rain and Sun threshold adjustment pots, the DEMO and
Program Buttons and the Mode Dip Switches (Fig 2).
3 - Do not remove the sticker over dip switches 3 and 4. Only Dip switches 1 and 2 will be
used to select the Mode for normal Awning use.
4 - Select the desired mode using dip switches 1 and 2. Dips 3 and 4 should remain off.
ON
1 2 3 4
Awning Rain
ON
1 2 3 4
Awning Sun
ON
Latch
Hatch
Sun LED
Rain LED
1 2 3 4
Awning Rain & Sun
5 - In Awning Rain mode (A), the SRS will run the awning in when the rain rate exceeds
the set rain threshold.
6 - In Awning Sun mode* (B), the SRS will run the awning in after about 15-30 min with the
sun below the set sun threshold and out after about 2 min with the sun above the threshold.
7 - In Awning Rain & Sun mode* (C), the rain and sun functions are both active but a rain
event will override the sun function until the rain rate falls below the set threshold for 5 min.
8 - The Sun and Rain threshold adjustment pots can be turned 280 deg from the minimum
setting to the maximum. (Fig 3)
9 - The Rain threshold (Fig 4) can be set from:
Min (fully CCW) = Very Light Rain/Heavy Mist/Heavy Condensation
Max (fully CW) = Very Heavy Rain.
10 - The Sun threshold (Fig 5) can be set from
Min (fully CCW) = approx 0.5klux - Facing sun with heavy cloud cover
Max (Fully CW) = approx 55klux - Facing direct summer sun with no cloud cover
11- LED indicators, The rain and sun LEDs will blink when conditions are above the
threshold, continuously in DEMO mode and every 5 sec in normal mode.
Note; In order for the SRS to activate a motor in response to sun, the sun function of the motor
must be enabled. To enable this feature, a Soliris Transmitter must be used and therefore
programmed to the motor.
Factory Default settings:
ON
Min Max
1 2 3 4
Awning Rain
RAIN
Approx 9:00
Light Rain
Fig 1
RAIN
SUN
ON
DEMO
PROG
Fig 2 Sticker
POT
Adj
Range
Min
Min Max
Max
280 deg
Fig 3
RAIN
Fig 4
Min Max
SUN
Approx 12:00
Facing Sun, Light Cloud Cover
Important: If the RTS Rain and Sun sensor is removed from a job site it must be deleted from the motor memory.
(see next section)
Min Max
SUN
Fig 5
Instructions Somfy Solar Rain Sensor (SRS) - RTS
2.088”
[53.04]
2.590”
[65.79]
4.479”
[113.77]
IMPORTANT - Read the entire instructions and ensure the unit is charged before starting installation (see installation section)
Mode and Threshold Selection - Shutter/Screen (S/S)
1 - Open the hatch by pressing the latch toward the hatch and pulling outward (Fig 1)
2 - Inside the hatch you will see the Rain and Sun threshold adjustment pots, the DEMO and
Program Buttons and the Mode Dip Switches (Fig 2).
3 - Remove the sticker over dip switches 3 and 4.
4 - Select the desired mode using dip switches 2, 3 and 4. Dip switch 1 should remain off.
ON
1 2 3 4
Shutter/Screen Rain
ON
1 2 3 4
S/S Rain & Sun
Latch
Hatch
Sun LED
Rain LED
ON
Fig 1
1 2 3 4
S/S Rain & Auto
5 - In S/S Rain mode (E), the SRS will send a down command when the rain rate exceeds
the set rain threshold and will not send another rain command until the rain falls below the
rain threshold for 5 min and then goes above the threshold again..
6 - In S/S Rain & Sun mode (F), Rain functions as per Mode E. A rain event will lock out the
sun function until it falls below the threshold for 5 min. Sun light detected over the sun
threshold for 2 min will cause a down (out) command. Sunlight under the threshold for 15min
will cause an up (in) command
7 - In S/S Rain & Auto mode (G), Rain functions as per Mode E. When the rain falls below
the rain threshold for 5 min continuous, the sensor will send an automatic up command.
8 - The Sun and Rain threshold adjustment pots can be turned 280 deg from the minimum
setting to the maximum. (Fig 3)
9 - The Rain threshold (Fig 4) can be set from:
Min (fully CCW) = Very Light Rain/Heavy Mist/Heavy Condensation
Max (fully CW) = Very Heavy Rain.
10 - The Sun threshold (Fig 5) can be set from
Min (fully CCW) = approx 0.5klux - Facing sun with heavy cloud cover
Max (Fully CW) = approx 55klux - Facing direct summer sun with no cloud cover
11- LED indicators, The rain and sun LEDs will blink when conditions are above the
threshold, continuously in DEMO mode and every 5 sec in normal mode.
Factory Default settings:
ON
Min Max
1 2 3 4
Awning Rain
RAIN
Approx 9:00
Light Rain
RAIN
DEMO
SUN
ON
PROG
Fig 2 Sticker
POT
Adj
Range
Min
Max
280 deg
Fig 3
Min Max
RAIN
Fig 4
Min Max
SUN
Approx 12:00
Facing Sun, Light Cloud Cover
Important: If the RTS Rain and Sun sensor is removed from a job site it must be deleted from the motor memory.
(see next section)
Min Max
SUN
Fig 5
Programming
Step 2
*Before programming ensure the sensor is set to the desired mode (Mode
selection - Step 4 on page 1) and ensure the unit is charged (see below)
Latch
Adding the sensor
1- Put the motor into learning mode by pressing the programming button on
an already programmed transmitter until the motor jogs.
2- Open the hatch on the sensor and press the programming button. The
motor will jog.
Hatch
Deleting the sensor
Repeat steps 1 and 2 above.
RAIN
SUN
ON
DEMO
PROG
Programming
Button
RAIN
DEMO
SUN
ON
PROG
DEMO Button
Rain LED
-When the rain or sun condition passes a set threshold for the delay time listed above the
command (XX) is given. Rain present locks out sun functions and normal transmitters.
- In DEMO mode the LEDs will blink when conditions are above the threshold. In normal
mode the LEDs will blink every 5 sec if conditions are above the threshold.
Sun LED
Installation
Front tabs into top slot 1
Mast pole orientation
Back tabs into
lower slot 2
Vertical wall orientation
Vertical Wall
- Initial Charge - The Somfy Solar Rain Sensor (SRS) RTS is solar powered. Before installation
ensure the unit has an initial charge by placing the unit with the solar cell facing direct sun light.
The initial charge will take about 10 min in direct outdoor sun light.
- Mounting Bracket - The mounting is released by pushing the bracket clips gently towards
the main body of the control. The bracket can be used to mount the SRS to a vertical wall using
screws or to a 2 inch mast pole using zip ties. For a vertical wall the bracket is placed flat face
towards the wall. For a mast pole mount the curved face is mounted to the pole.
- Mounting Location - The Sensor should be mounted in a clear unobstructed location with the
sensor facing the sun in the same facing as the awning.
The sensor must be mounted with clear exposure to the rain in the same facing as the awning.
The sensor must be mounted with the clear cover facing upward as shown (correct mount), with
the sensor face at an angle. This allows excess moisture to run off and clear debris from the face.
NOTE - If the sensor is removed from a job site, it must be deleted from the motor’s memory.
Bracket
Clip
Mounting
Bracket
Correct mount

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Warning                         : Bad Kids reference
Page Count                      : 4
Create Date                     : 2015:04:17 12:14:21-04:00
Modify Date                     : 2015:04:17 12:14:21-04:00
Producer                        : Corel PDF Engine Version 17.0.0.491
Author                          : Glen Sanders
Creator                         : CorelDRAW X7
Title                           : RTS rain sensor instr full FCC.cdr

EXIF Metadata provided by EXIF.tools