Somfy Systems URTSII Universal RTS Interface II URTSII (#1810872 User Manual

Somfy Systems Universal RTS Interface II URTSII (#1810872 urtsi2

a href="https://usermanual.wiki/Somfy-Systems" itemprop="url"> Somfy Systems >

User manual

UNIVERSAL RTS INTERFACE IIOperating InstructionsThe addressable Universal RTS Interface II (URTSI II) can be used to communicate between home automation or other third party systems and SOMFY’s RTS Motors and controls. It is capable of individual or group control, and can be operated via infrared remote, RS232 and RS485 serial communication. Once an input is activated, an RTS radio command is sent to the automated window treatment. DESCRIPTIONCONNECTION DIAGRAMBack of Interface control boxAntennaIR Sensor InputRS232 Input or RS485 Input RS485 Input/OutputPowerFront of Interface control boxF0EDCBA968753412UP ButtonSTOP ButtonPower/Transmit LEDURTSI Address orRTS Channel Rotary SwitchProgram ButtonDOWN ButtonPin 4Pin 1IR SignalCommon+5V DCIR Sensor Modular Pin-OutPin 8Pin 1 RS485 ACommon+5V DCRS232/RS485 Pin-OutRS485 BRS232TXRS232TXPart Number: 1810872N/CFCC INFORMATIONThis device complies with Part 15 of the FCC Results. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and2. This device must accept any interference received, including that which may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:1. Reorient or relocate the receiving antenna2. Increase the separation between the equipment and receiver3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected4. Consult the dealer or experienced radio/TV technician for help.WARNINGChanges or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.NOTE: Do Not remove antenna. If a new antenna is needed, it must be ordered from Somfy to ensure FCC requirements are maintained.
A. INITIAL SETUP1. Connect a 9v DC transformer (included) to the receptacle on the back of the control box. The LED will light green to indicate power.2. Be careful not to mount or enclose Interface on or in metal, as this may effect radio reception.3. Set the RTS Receiver or motor into its Programming Mode. Refer to the installation instructions of the relevant RTS receiver or motor for this procedure. NOTE: for initial programming provide power only to the motor or control being programmed. 4. Using the rotary switch, select the channel to be programmed. Letters A through F stand for channels 10 through 15, 0 for 16. Briefly press the programming button (1 sec. max), the window treatment will jog to indicate the channel has been memorized. 5. Repeat the steps above for each channel or product to be memorized, up to 16. 6. To test the control operation, simply press the UP, STOP or DOWN buttons on the front of the control. The window treatment should move appropriately. The LED will flash red to indicate the radio signal has been transmitted.B. INFRARED OPERATION1. The RTS Interface is compatible with Somfy’s multichannel transmitter. Connect an infrared sensor to the appropriate connector on the back of the Interface. 2. Each individual motor is activated by first aiming the transmitter at the sensor and pressing the desired unit number on the transmitter and then pressing the UP or DOWN buttons. Press the center button to STOP the window treatment at any time.C. RS232 OPERATION1. The Somfy RS232 interface uses the following communications settings: 9600 Baud, 8 Data Bits, 1 Stop Bit, No Parity2. Set the rotary switch to position 1. 3. The basic format for communication is as follows: URTSI ADDR MOTOR CHAN DIR The URTSI address is 01. The motor channel should be 2 digits from 01 to 16. The directional commands are: U = Up D = Down S = Stop4. Examples:Motor 1 UP: 01 01 UMotor 5 DOWN: 01 05 DMotor 12 STOP: 01 12 S D. RS485 OPERATION1. The Somfy RS485 interface uses the following communications settings: 9600 Baud, 8 Data Bits, 1 Stop Bit, No Parity2. With RS485, it is possible to connect 16 Universal RTS Interfaces on one network. Each Interface will have its own address. To select the address, set the rotary switch to the desired number. Letters A through F stand for addresses 10 through 15, 0 for 16. 3. The basic format for communication is as follows: URTSI ADDR MOTOR CHAN DIR The URTSI address should be 2 digits from 01 to 16. The motor channel should be 2 digits from 01 to 16. The directional commands are: U = Up D = Down S = Stop4. Examples:URTSI 1, Motor 1 UP: 01 01 UURTSI 3, Motor 12 DOWN: 03 12 DURTSI 14, Motor 9 STOP: 14 09 SURTSI 10, Motor 15 UP: 10 15 UOPERATIONMECHANICAL SPECIFICATIONS 3 Overall Dimensions: L: 3 in. W: 4 in. D: 1 /8 in. Typical Range (Optimal Conditions): 65 ft.ELECTRICAL SPECIFICATIONS Power: 9V DC, 200mA Frequency: 433.42 MhzDescription Universal RTS Interface IIMultiChannel Infrared TransmitterMini Infrared Sensor ORDERING INFORMATIONPart Number181087218104989012093Description DB9 to RJ45 Adapter for RS232DB9 to RJ45 Adapter for RS485 Part Number90150289015029Ref. No. 2500872 SOMFY SYSTEMS, INC. 6/08CSOMFY SYSTEMS, INC.47 Commerce Drive Cranbury, NJ 08512SOMFY CANADA6315 Shawson Drive, Unit #1Mississauga, Ontario L5T1J2SOMFY SYSTEMS, INC. reserves the right to change, update or improve this document without prior notice.
Download:
Mirror Download [FCC.gov]
Document ID967955
Application IDL9zZhrJEuGvtjCh+cdbfNg==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize14.19kB (177406 bits)
Date Submitted2008-07-09 00:00:00
Date Available2008-07-09 00:00:00
Creation Date2008-07-02 18:58:26
Producing SoftwareCorel PDF Engine Version 3.0.0.576
Document Lastmod2008-07-02 18:58:26
Document Titleurtsi2.cdr
Document CreatorCorelDRAW
Document Author: oconte01
FCC ID Filing: DWNURTSII

Navigation menu