Sonicwall 046 Ethernet Firewall/VPN/Router with Wireless LAN User Manual SonicWALL TZ190 W Getting Started Guide newREG

Sonicwall, Inc. Ethernet Firewall/VPN/Router with Wireless LAN SonicWALL TZ190 W Getting Started Guide newREG

Guide

DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 1SonicWALL TZ 190 WirelessGetting Started GuideThis Getting Started Guide contains installation procedures and configuration guidelines for deploying a SonicWALL TZ 190 Wireless appliance on your network.SonicWALL TZ 190 Wireless Wireless provides a flexible, total Internet security platform for wired and wireless users over Wireless Wide Area Networks (WWAN). This easy to configure appliance delivers the office-on-a-park-bench mobility and convenience of WWAN technology along with the powerful protection of true layered security, integrating gateway anti-virus, gateway anti-spyware, intrusion prevention and content filtering capabilities in an easy-to-use, low cost platform.This Getting Started Guide provides instructions for basic installation and configuration of the SonicWALL TZ 190 appliance using a SonicWALL approved WWAN PC card and service from a third-party wireless provider. After you complete this guide, you will have secure Internet access (WAN / WWAN) and a secure Local Area Network (LAN) / Wireless Local Area Network (WLAN).The SonicWALL TZ 190 appliance requires the use of a SonicWALL approved WWAN PC card along with a data account from a supported third-party wireless service provider. For an updated list of SonicWALL approved WWAN cards and service providers, visit the SonicWALL TZ 190 Wireless Wireless product page at: <http://www.sonicwall.com/products/tz190_details.html>Alert: DO NOT INSERT YOUR WWAN PC CARD INTO ANY DEVICE UNTIL YOU HAVE READ THIS GUIDE. INSERTING YOUR WWAN PC CARD INTO A DEVICE BEFORE PROPER SETUP AND PROVISIONING HAS TAKEN PLACE CAN RESULT IN CONNECTIVITY ISSUES.Note: SonicWALL makes no warrants, representations or claims that the user of this product will experience continuous broadband-like speeds. The speed of the WWAN connection will vary depending on available wireless technology (GPRS/HSDPA/EV-DO), WWAN card, wireless service area and other factors.
DRAFT not for productionPage 2 Important Information Regarding WWAN Service ProvidersIt is important to understand that not all WWAN service providers operate in the same way, nor do they all support the same feature sets. Because of this, there exists some inherent “service provider-specific” variances in service area and more importantly, in supported features. Along with feature limitations may also come certain restrictions such as bandwidth constraints and networking limitations. Before purchasing a WWAN PC card and service plan, check to make sure that the WWAN service provider offers support for the features you need. Before committing to a service contract with a WWAN service provider, it may be helpful to ask these questions:• What types of traffic are allowed over the WWAN network?• Do they offer “static” or “dynamic” IP addressing?• Are there any inbound connection limitations?• Are single or multiple hosts allowed?• Do they support VPN traffic?• What are the data transfer limits (inbound and outbound)?• What are common data transfer speeds and how much of the coverage area supports 3G or faster technology?Document ContentsThis document contains the following sections:Completing Pre-Configuration TasksPreparing Your WWAN PC CardRegistering Your SonicWALL TZ 190 Wireless ApplianceSetting Up Your SonicWALL TZ 190 Wireless ApplianceUsing the SonicWALL Configuration WizardVerifying Your WWAN ConnectionConnecting the SonicWALL TZ 190 Wireless to Your Network1234567
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 3Completing Pre-Configuration TasksThis section contains the following sub-sections:• “Before You Begin” on page 3• “Checking Package Contents” on page 4• “Recording Configuration Information” on page 5• “Recording Internet Service Provider (ISP) Information” on page 6• “Overview of the SonicWALL TZ 190 Wireless Appliance” on page 7Before You BeginBefore you begin the setup process, check to ensure that you have the following required components available:• A SonicWALL approved WWAN Wireless PC Card and a service contract with a WWAN service provider• Your WWAN service provider’s installation software• A laptop computer with:• Windows XP or Windows 2000• One available PC card slot• 40MB of disk space available• A Web browser supporting Java and HTTP uploads. Internet Explorer 6.0 or higher, Netscape Navigator 4.7 or higher, Mozilla 1.7 or higher, or Firefox are recommendedNote: For an updated list of SonicWALL approved WWAN cards and service providers, visit the SonicWALL TZ 190 Wireless product page at: <http://www.sonicwall.com/us/tz190cards.html>1
DRAFT not for productionPage 4 Checking Package Contents One SonicWALL TZ 190 appliance Wireless antenna pairOne standard power adaptor*One DB9 -> RJ45 (CLI) CableOne Ethernet CableOne SonicWALL Resource CDOne Getting Started Guide DocumentOne Release Notes DocumentOne Thank You CardOne Security Subscription Card* The included power cord is intended for use in North America only. For European Union (EU) customers, a power cord is not included. * Das eingeschlossene Netzkabel ist für Gebrauch in Nordamerikas nur vorgehabt. Für Europaïsche Union (EU) Kunden, ist ein Netzkabel nicht eingeschlossen. Any Items Missing?If any items are missing from your package, please contact SonicWALL support. A listing of the most current support options is available online at: <http://www.sonicwall.com/us/support.html>12345678910wan optwwanSonicWALLResource CDPRO 2040SonicPointThank YouFor selecting SonicWALL ProtectionSonicWALL offers a wide range of high performance network security135768942SonicWALL Getting Started GuideCOMPREHENSIVE INTERNET SECURITY
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 5Recording Configuration InformationBefore continuing, record the following configuration information for your reference:WWAN Connection InformationRegistration InformationNetworking InformationWWAN Service Provider: (Cingular, Verizon, etc.)Record the name of your WWAN service provider.WWAN Plan Type: (Standard, Acceleration, VPN, etc.)Record the type of plan you have with your WWAN service provider. If you are not sure what your plan type is, ask your service provider.Serial Number: (xxxxxxxxxxxx)Record the serial number found on the bottom panel of your TZ 190 Wireless appliance.Authentication Code: (xxxx-xxxx)Record the authentication code found on the bottom panel of your TZ 190 Wireless appliance.TZ 190 Wireless LAN IP Address: Select a static IP address for your TZ 190 Wireless appliance that is within the range of your local subnet.TZ 190 Wireless Subnet Mask: Record the subnet mask for the local subnet where you are installing your TZ 190 Wireless appliance.Ethernet WAN IP Address: (optional)Select a static IP address for your Ethernet WAN. This setting only applies if you are already using an ISP that assigns a static IP (as in the case of a landline T1/E1 connection, where the WWAN is a failover).DNS Server 1 : (optional)DNS Server 2 : (optional)In most cases, DNS server information is automatically provided by your WAN service provider upon connection. Record your DNS server information here if your network requires it. If for example, you make use of internal DNS servers.
DRAFT not for productionPage 6 Administrator InformationRecording Internet Service Provider (ISP) InformationIf you already have an Internet connection and are using the WWAN connection as a backup or “failover”, collect the following information about your current Internet service:Note: You do not need to complete this information if you are using the WWAN PC Card as your only connection to the Internet.TZ 190 Wireless Admin User: Select an administrator account name for your SonicWALL TZ 190 Wireless appliance (default is admin).TZ 190 Wireless Admin Password: Select an administrator password for your SonicWALL TZ 190 Wireless appliance (default is password).If you connect via You probably use Please recordCable modem,DSL with a routerDHCP No Internet connection information is usually required. Some service providers require a host name. Check with your ISP. Host Name: Home DSL PPPoE User Name: Password: Note: Your ISP may require your user name in the format: name@ISP.comT1/E1,Static broadband,Cable or DSL with a static IPStatic IP IP Address: Subnet Mask: Default Gateway(Router IP Address): Primary DNS: Secondary DNS (optional): Dial-in to a server PPTP Server Address: User Name: Password:
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 7Overview of the SonicWALL TZ 190 Wireless Appliance*For an updated list of SonicWALL approved WWAN cards and service providers, visit the SonicWALL TZ 190 Wireless product page at: <http://www.sonicwall.com/us/tz190cards.html>link/act10/100signallink/actwan optWWANTZ 190PC Card Slot Power LEDTest LEDWWAN Signal/Act WAN LEDOPT LED Link/Act 1-810/100 1-8Feature DescriptionPC Card Slot Location to insert your WWAN PC Card modem. For use only with SonicWALL approved PC cards.*Power LED Indicates the SonicWALL TZ 190 Wireless appliance is powered on.Test LED Solid: Indicates that the SonicWALL TZ 190 Wireless appliance is in test mode. Blinking: The unit is first booting up, or restarting. This can also indicate that the unit is in safe mode.WWAN Indicates WWAN signal or link activity through your WWAN PC Card.WLAN Indicates power, activity and WiFiSec enforcement on your WLAN.WAN Indicates a device link, activity and connection speed on your WAN port.OPT Indicates a device link, activity and connection speed on your OPT port.LAN Ports 1-8 Indicates a device link, activity and connection speed on individual LAN ports.Signal Indicates availability and strength of a signal (WWAN port only).Link/ACT Solid: Indicates a device is connected to the specified port(s).Blinking: Indicates activity on the specified port(s).10/100 Green: Indicates 10M connection on the specified port(s).Amber: Indicates 100M connection on the specified port(s).
DRAFT not for productionPage 8 Preparing Your WWAN PC CardThis section provides instructions to set up your WWAN PC card for use in the SonicWALL TZ 190 Wireless appliance.This setup process differs depending on you service provider. Choose your service provider from the list below and follow the instructions on how to set up your WWAN PC Card. If your service provider is not listed here, you must still complete the setup and activation for your PC Card modem using the documentation that came with it before it can be used in the SonicWALL TZ 190 Wireless appliance.Alert: DO NOT insert your PC Card into the SonicWALL TZ 190 Wireless appliance until you have completed the setup process for your card as described in this section. Tip: If your WWAN PC Card is already registered and activated with your service provider and you are able to access the Internet through your PC using this card, you may skip this section and continue to “Setting Up Your SonicWALL TZ 190 Wireless Appliance” on page 23.Choose one of the PC card setup options below:General WWAN PC Card SetupThis section provides general instructions for setting up most WWAN PC cards:• “WWAN PC Card Setup” on page 9Specific PC Card SetupThe following sections provide specific instructions for setting up specific cards:• “Sprint Wireless PC Card Setup” on page 11• “Cingular Wireless PC Card Setup” on page 14• “Verizon Wireless PC Card Setup” on page 172
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 9WWAN PC Card SetupComplete the following steps to set up and provision your WWAN PC Card Modem. Before continuing, check to make sure that your WWAN PC card and service provider are supported by the SonicWALL TZ 190 Wireless appliance by visiting the SonicWALL TZ 190 Wireless product page at: <http://www.sonicwall.com/us/tz190cards.html>Contact your PC card vendor for troubleshooting help with this section.Alert: DO NOT insert your PC Card modem into the computer until you have completed the setup process for your card as described in this section and successfully accessed the Internet through your PC using the PC Card modem.Installing PC Card SoftwareThe following steps are general prerequisites necessary to set up most WWAN PC card modems to work with the TZ 190 Wireless.1. Install the software that came bundled with your WWAN PC card modem before activating the card.2. When prompted, insert the WWAN PC card modem into an available Type II PC card slot on the Windows PC you are using for card configuration.3. Check for updates and install updates to your WWAN PC card (if available).4. Activate your PC Card modem (if required). Verifying Your ConnectionAfter the card has been set up on your PC, you can view your connection type and verify that the WWAN PC Card is transferring data.Note: In order for the connection testing to be valid, it is important that you first disable all other network connections, such as a Wi-Fi or LAN connection, before continuing. Leave only your PC card connection enabled.5. Use the software that came with your WWAN PC card modem to initialize a connection with your service provider.6. In the Windows interface, select Start > Run.7. Enter “cmd” in the Open field and click the OK button.8. At the prompt, type the command “ipconfig” and press Enter on the keyboard. 9. Your network device status will display. Verify that you have obtained an IP Address for your Ethernet adaptor, and that all other Local Area Network Connections display “Media disconnected” as their status.
DRAFT not for productionPage 10 Note: The name of your Ethernet adaptor may differ from the screenshot below. Common names for newly acquired cards are “Local Area Connection 2” or “Local Area Connection 3”.10. Open a Web-browser and navigate to a website, such as <http://www.sonicwall.com> to verify that your connection can transfer data.Congratulations! You have set up and provisioned your WWAN PC card. Continue with “Setting Up Your SonicWALL TZ 190 Wireless Appliance” on page 23.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 11Sprint Wireless PC Card SetupComplete the following steps to set up and provision your Sprint Wireless Mobile Broadband (WWAN) PC card. Contact your PC card vendor for troubleshooting help with this section.Alert: DO NOT insert your PC Card modem into the computer until you have completed the setup process for your card as described in this section and successfully accessed the Internet through your PC using the PC Card modem.Installing Sprint SoftwareYou must install the Sprint Wireless software that came bundled with your WWAN PC card before activating the card.1. Insert the Sprint CD that is provided with your WWAN PC card into the PC you intend to use for PC card setup.2. Follow the instructions on screen to complete the Sprint software installation.3. Restart your computer when prompted.4. After restarting your computer, open the Sprint PCS Connection Manager program (if it does not automatically start).5. When the program launches, it will check for updates. Click Update Now as needed. The download and update will proceed (if needed) and the program may restart.Setting Up the WWAN PC Card1. Insert your Sprint WWAN PC Card. You may hear some audible indications of the card being discovered and installed.2. Once installed, you may be prompted to update the firmware on the WWAN PC card. Click OK to proceed with the update and click Next to agree to the license terms. The update will take a few minutes. The WWAN PC Card will be rediscovered during this process. Click Finish when prompted.3. When the card is fully rediscovered, you will be prompted to call Sprint PCS Customer Service to activate the card. Do not click next until prompted to do so by the Sprint agent.4. The Sprint agent will provide you with an Activation Code, and instruct you to enter it on the next screen. Enter the Activation Code and click Next.5. If the code is accepted, you will be prompted to enter your phone number (MDN) and MSID. Verify these numbers with the Sprint agent, and be sure to enter them correctly. Click Next when done.6. You will be prompted to confirm the correctness of the numbers. Entering incorrect information at this stage will require recovery by Sprint Technical Support. Click Yes once you have verified the numbers.
DRAFT not for productionPage 12 7. You will be presented with a screen indicating the completion of the Activation process. Click Finish to proceedVerifying Your ConnectionIt may take up to 4 hours for your WWAN PC card to become active on the Sprint network. After the card has been set up and is active, you can view your connection type and verify that the WWAN PC Card is transferring data.Alert: In order for the connection testing to be valid, it is important that you first disable all other network connections, such as a Wi-Fi or LAN connection, before continuing. Leave only your PC card connection enabled.1. Open the Sprint PCS Connection Manager program.2. Click the GO button to connect to the Sprint network.The WWAN PC card will take a few minutes to connect to the Sprint network. When the connection is ready, the status will read “Connected”. Note: If you have recently activated your card with Sprint, keep in mind that the initial activation of your card may take up to 4 hours.3. In the Windows interface, select Start > Run.4. Enter “cmd” in the Open field and click the OK button.5. At the prompt, type the command “ipconfig” and press Enter on the keyboard. Your network device status will display.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 136. Verify that you have obtained an IP Address for your Ethernet adaptor. 7. Verify that all other Local Area Network Connections display “Media disconnected” as their status.Note: The name of your Ethernet adaptor may differ from the screenshot below. Common names for newly acquired cards are “Local Area Connection 2” or “Local Area Connection 3”.8. Open a Web-browser and navigate to a website, such as <http://www.sonicwall.com> to verify that your connection can transfer data.Congratulations! You have set up and provisioned your WWAN PC card. Continue with “Setting Up Your SonicWALL TZ 190 Wireless Appliance” on page 23.
DRAFT not for productionPage 14 Cingular Wireless PC Card SetupComplete the following steps to set up and provision your Cingular Wireless 3G PC card. Contact your PC card vendor for troubleshooting help with this section.Alert: DO NOT insert your PC Card modem into the computer until you have completed the setup process for your card as described in this section and successfully accessed the Internet through your PC using the PC Card modem. Installing Cingular SoftwareYou must install the Cingular software that came bundled with your 3G PC card modem before activating the card.1. Insert the Cingular CD that is provided with your PC card modem into the PC you intend to use for PC card setup.2. Follow the instructions on screen to complete the Cingular software installation.3. Restart your computer if prompted.4. If the Cingular Communications Manager program is running, skip to the next step. Otherwise, navigate to Start > Programs > Cingular > Cingular Communications Manager to start the Communications Manager program.5. De-select all checkboxes on the first configuration page, including the Use this as my default Wi-Fi management utility option (checked by default).6. A warning screen will display. Check the Do not show this message again checkbox and click the OK button to continue.7. Click the Finish button to complete post-install configuration.Preparing the PC CardNow that you have installed the required activation software on our PC, you can prepare the card for first use.1. Remove the PC card from the packaging and attach antenna if necessary.2. Locate your SIM chip and remove it from its packaging if necessary (the SIM chip may be attached to a larger 3x5 plastic card from which it must be removed).3. Insert the SIM chip into your PC card modem. When inserted correctly, the SIM chip will “click” in place and sit perfectly flush with the edge of the PC Card.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 15Note: Pay close attention to the orientation of your SIM card when inserting. Follow the manufacturer’s directions carefully when completing this procedure.4. Insert the PC card modem into an available Type II PC card slot on your Windows PC.5. If the Cingular Communications Manager program is running, skip to the next step. Otherwise, navigate to Start > Programs > Cingular > Cingular Communications Manager to start the Communications Manager program. When the program is launched, you will see an interface similar to the one below.6. Optionally, you may select Tools > Check for Updates to see if updates are available for your card vendor.Note: Additional updates, including those for the PC card firmware may be recommended by Cingular. If so, follow the steps provided to complete these updates before continuing.SIMchipWWAN PC Card3G - Indicator will show when you are connected to a 3G enabled network.GSM Tab - Use this tab for WWAN PC card manage-ment.Connect Button - Click here to make a connection to the current network.Status - Shows “ready” when a connection is available.Signal - Displays the signal strength of your current connection.
DRAFT not for productionPage 16 Verifying Your ConnectionAfter the card has been set up on your PC, you can view your connection type and verify that the WWAN PC Card is transferring data.Alert: In order for the connection testing to be valid, it is important that you first disable all other network connections, such as a Wi-Fi or LAN connection, before continuing. Leave only your PC card connection enabled.1. If the Cingular Communications Manager program is running, skip to the next step. Otherwise, navigate to Start > Programs > Cingular > Cingular Communications Manager to start the Communications Manager program. The WWAN PC card will take a few minutes to connect to the Cingular network. When the connection is ready, the status will read “Ready: Cingular Accelerated”.2. Click the Connect button to enable the network connection.3. In the Windows interface, select Start > Run.4. Enter “cmd” in the Open field and click the OK button.5. At the prompt, type the command “ipconfig” and press Enter on the keyboard. Your network device status will display. 6. Verify that you have obtained an IP Address for your Ethernet adaptor. 7. Verify that all other Local Area Network Connections display “Media disconnected” as their status.Note: The name of your Ethernet adaptor may differ from the screenshot below. Common names for newly acquired cards are “Local Area Connection 2” or “Local Area Connection 3”.8. Open a Web-browser and navigate to a website, such as <http://www.sonicwall.com> to verify that your connection can transfer data.Congratulations! You have set up and provisioned your WWAN PC card. Continue with “Setting Up Your SonicWALL TZ 190 Wireless Appliance” on page 23.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 17Verizon Wireless PC Card SetupComplete the following steps to set up and provision your Verizon Wireless WWAN PC card. Contact your PC card vendor for troubleshooting help with this section.Alert: DO NOT insert your PC Card modem into the computer until you have completed the setup process for your card as illustrated in this section and successfully accessed the Internet through your PC using the PC Card modem.Installing Verizon SoftwareYou must install the Verizon software that came bundled with your WWAN PC card modem before activating the card.1. Insert the Verizon CD that is provided with your PC card modem into the PC you intend to use for PC card setup.2. Follow the instructions on screen to complete the software installation.3. Exit the installer after setup is complete.4. Navigate to Start > Programs > Verizon > VZAccess Manager to start the VZAccess Manager program.5. Click the Check for Updates button. When finished, click Next to continue.6. Select the Detect WWAN device only (1xEVDO/1xRTT/CDMA) radio button and click the Next button to continue.7. Click the Next button to search for your WWAN PC card.8. Select the PC Card radio button and click the Next button to continue.9. Click the Finish button to complete post-install configuration.10. Insert the PC card modem into an available Type II PC card slot on your Windows PC.11. When your card is found, click the Next button to continue.12. Click the Activate button to activate your WWAN PC card modem.Note: If activation fails on the first attempt, exit and then re-launch the program, keeping the WWAN PC Card inserted during the process.13. An “Activation Successful” message will appear. Click the OK button.14. Click the Next button.15. Verify the correctness of the wireless phone number assigned to this PC card. If the number is incorrect, enter the correct number in the Phone number field. Click the Next button to continue.16. Uncheck the Run VZAccess Manager at Startup option (unless you intend to use VZAccess to manage wireless connections on this PC). Click the Finish button.
DRAFT not for productionPage 18 Verifying Your ConnectionAfter the card has been set up on your PC, you can view your connection type and verify that the WWAN PC Card is transferring data.Note: In order for the connection testing to be valid, it is important that you first disable all other network connections, such as a Wi-Fi or LAN connection, before continuing. Leave only your PC card connection enabled.1. If the VZAccess Manager program is running, skip to the next step. Otherwise, navigate to Start > Programs > Verizon > VZAccess Manager to start the VZAccess Manager program.The WWAN PC card will take a few minutes to connect to the network. When the connection is ready, the signal indicator will light up green with bars to indicate connection strength.2. Click the Connect button to enable the network connection. 3. If a disclaimer displays, click the Continue button. When the connection attempt is successful, the bottom-left corner of the VZAccess Manager will read Connected.4. In the Windows interface, select Start > Run.5. Enter “cmd” in the Open field and click the OK button.6. At the prompt, type the command “ipconfig” and press Enter on the keyboard. Your network device status will display. Connect/Disconnect Button - Click here to connect or disconnect from the current network.Status - Shows “connected” when connected to the Verizon network.Network Connection Shows “Verizon Wireless” when connected to the Verizon network.Signal - Displays the signal strength of your current connection.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 197. Verify that you have obtained an IP Address for your Ethernet adaptor.8. Verify that all other Local Area Network Connections display “Media disconnected” as their status.Note: The name of your Ethernet adaptor may differ from the screenshot below. Common names for newly acquired cards are “Local Area Connection 2” or “Local Area Connection 3”.9. Open a Web-browser and navigate to a website, such as <http://www.sonicwall.com> to verify that your connection can transfer data.Congratulations! You have set up and provisioned your WWAN PC card. Continue with “Setting Up Your SonicWALL TZ 190 Wireless Appliance” on page 23.
DRAFT not for productionPage 20 Registering Your SonicWALL TZ 190 Wireless ApplianceThis section contains the following sub-sections:• “Before You Register” on page 20• “Creating a mysonicwall.com Account” on page 21• “Registering Your SonicWALL TZ 190 Wireless Appliance” on page 22Before You RegisterYou need a mysonicwall.com account to register the SonicWALL TZ 190 Wireless appliance. If you already have a mysonicwall.com account, go to “Registering Your SonicWALL TZ 190 Wireless Appliance” on page 22 to register your appliance.Note: mysonicwall.com registration information is not sold or shared with any other company.3
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 21Creating a mysonicwall.com AccountCreating a mysonicwall.com account is fast, simple, and FREE. Simply complete an online registration form.1. In your Web browser, go to <https://www.mysonicwall.com>.2. In the User Login section, click the “Click here” link in “If you are not a registered user, Click here.”3. Enter the account information, personal information, and preferences and click Submit. Note: You must enter a valid email address.4. Follow the prompts to finish creating your account. SonicWALL will email a subscription code to the email address you entered in the personal information. 5. When you return to the login screen, log in with your new username and password. 6. Confirm your account by entering the subscription code you received in the email. Congratulations, you have created and logged into your mysonicwall.com account. Continue to “Registering Your SonicWALL TZ 190 Wireless Appliance” on page 22.
DRAFT not for productionPage 22 Registering Your SonicWALL TZ 190 Wireless Appliance1. Locate your SonicWALL TZ 190 Wireless Software Serial Number and Authentication Code. This information is printed on the bottom panel of your SonicWALL TZ 190 Wireless appliance.2. In your Web browser, go to <https://www.mysonicwall.com> and login with your mysonicwall.com username and password.3. Enter your serial number in the Quick Register field and click the small gray arrow. Follow the on-screen instructions. 4. Confirm your serial number.5. Enter a friendly name for this appliance.6. Enter your authentication code. 7. Click the Register button to continue.8. Follow the online prompts to fill out the survey and complete the registration process.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 23Setting Up Your SonicWALL TZ 190 Wireless ApplianceThis section contains the following sub-sections:• “Insert the WWAN PC Card Modem” on page 23• “Apply Power to the SonicWALL TZ 190 Wireless” on page 23• “Connect Directly to the SonicWALL TZ 190 Wireless Appliance” on page 24• “Log into the SonicWALL TZ 190 Wireless Appliance” on page 25• “If the SonicWALL Configuration Wizard Does Not Appear” on page 25Insert the WWAN PC Card ModemBefore inserting the WWAN PC card into your SonicWALL TZ 190 Wireless appliance, be sure your WWAN PC card is activated and unlocked. If you are not sure whether your card is unlocked or not, contact the PC Card vendor to verify.Note: Do not insert or remove the WWAN PC card while the SonicWALL TZ 190 Wireless is powered on.1. Ensure the TZ 190 Wireless is not connected to a power source.2. Insert your WWAN PC card modem “face up” into the PC CARD slot on the left side of the SonicWALL TZ 190 Wireless appliance. The card should sit firmly in place.Apply Power to the SonicWALLTZ 190 Wireless1. Connect one end of the power supply to the back of the SonicWALL TZ 190 Wireless2. Connect the other end of the power supply an appropriate power outlet.Note: The Power LED on the front panel lights up green when you power the SonicWALL TZ 190 Wireless appliance. The Test LED lights up and blinks while the appliance performs a series of diagnostic tests. When the Test LED is no longer lit, the SonicWALL TZ 190 Wireless appliance is ready for configuration. If the Test LED stays lit for more than a few minutes after the initial power on sequence, cycle power to the SonicWALL TZ 190 Wireless appliance.324link/act10/100signallink/actwan optWWANTZ 190
DRAFT not for productionPage 24 Connect Directly to the SonicWALL TZ 190 Wireless Appliance Before you can connect your management station to it, you must configure your management station to accept DHCP addressing or have it set to an address in the same subnet as the SonicWALL TZ 190 Wireless appliance. Note: If it is necessary to change networking settings on the computer you are using as a management station, record your computer’s current network settings so they can be restored after configuration is complete.1. Set the computer you are using to manage the SonicWALL TZ 190 Wireless appliance (management station) to accept DHCP addressing or to have a static IP address in the 192.168.168.x range, such as 192.168.168.20 and a subnet mask of 255.255.255.0.Note: For help with setting up a static IP address on your computer, refer to “Configuring a Static IP Address” on page 39.2. Using the supplied network cable and the management station, connect the LAN port on the management station to the LAN (1) port on the back of your SonicWALL TZ 190 appliance.SonicWALL TZ 190 ManagementStation
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 25Log into the SonicWALL TZ 190 Wireless Appliance1. Open a Web browser on the computer you are using to administer the SonicWALL TZ 190 appliance.2. Enter http://192.168.168.168 (the default IP address of the SonicWALL TZ 190 Wireless appliance) in the Location or Address bar. The SonicWALL TZ 190 Wireless Web management login screen displays:Note: Depending on your browser settings, one or more security warnings may display while connecting to the TZ 190 Wireless Web management interface. Choose to accept the certificates in order to log into the SonicWALL TZ 190 Wireless appliance.3. Log into the SonicWALL TZ 190 Wireless appliance using “admin” as the user name and “password” as the password. When you first log into the SonicWALL TZ 190 Wireless appliance, the Configuration Wizard screen displays. Continue to the next section “Using the SonicWALL Configuration Wizard” on page 26 for instructions on completing the Configuration Wizard.If the SonicWALL Configuration Wizard Does Not Appear• If you see the login screen, but not the Configuration Wizard:• Allow popups for the SonicWALL TZ190 appliance by adding the appliance’s default IP address (192.168.168.168) to your browser’s “allowed” list.• Log into the security appliance using “admin” as the user name and “password” as the password. After you log in, click the Wizards button on the System > Status page.• If you do not see the login screen or the Configuration Wizard:• Did you correctly enter the SonicWALL TZ 190 Wireless appliance management IP address, 192.168.168.168, in your Web browser? • Are the Local Area Connection settings on your computer set within the 192.168.168.x subnet range? If not, see “Configuring a Static IP Address” on page 39 for instructions on changing your Local Area Connection settings.• Do you have the Ethernet cable connected to your computer and to LAN (1) on your SonicWALL TZ 190 Wireless?• Do you need to add the SonicWALL TZ 190 Wireless to your list of trusted sites? Use the default IP address (192.168.168.168) for this purpose.
DRAFT not for productionPage 26 Using the SonicWALL Configuration WizardThe SonicWALL Setup Wizard provides administrator-guided instructions for configuring your SonicWALL TZ190 appliance. Note: It is important that you have collected any required configuration information before using the Setup Wizard. Be sure to fill out the information in “Recording Configuration Information” on page 5 and “Administrator Information” on page 6. SonicWALL TZ 190 Wireless Setup Wizard1. If the Setup Wizard does not display upon initial log into the SonicWALL TZ 190 Wireless appliance management interface, click the Wizards button in the left-hand navigation panel of the interface.2. Select Setup Wizard radio button and click the Next button to continue.5
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 27Changing Administrator Password3. Enter a New Password and Confirm that password. Click the Next button to continue.Note: Keep your new password in a safe place. If you lose your password, you will have to reset the SonicWALL security appliance to factory settings and will lose your configuration. For instructions on resetting your SonicWALL security appliance, refer to the SonicOS Enhanced Administrator’s Guide. Selecting a Time Zone4. Choose your local Time Zone form the drop-down list.5. If your location observes daylight savings time, check the Automatically adjust clock for daylight savings time checkbox.6. Click the Next button to continue.
DRAFT not for productionPage 28 Selecting the Proper WWAN Mode7. Select how you want to use your WWAN connection. Select from the following: 8. Click the Next button to continue.Configuring WWAN Service Provider Settings9. Select your WWAN service provider settings. Select from the following:10. Click the Next button to continue.Yes - I will use WWAN as a backup for the WAN Ether-net connection. Select this option if you currently have a WAN Internet con-nection and wish to use your WWAN wireless connection as a WAN failover.Yes - WWAN is my only connection to the Internet. Select this option if you wish to use your WWAN wireless connection as your primary connection to the Internet.No - I will not use the WWAN at this time. Select this option if you wish to configure your WWAN con-nection at a later time. You can always re-launch the wizard from the SonicWALL TZ 190 Wireless appliance manage-ment interface at a later time.Country Select the country this device is used in.Service Provider Select your WWAN service provider.Plan Type Select the plan type that your purchased from your service provider.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 29Verifying WWAN Service Provider Information11. Verify your WWAN service provider settings for correctness. In most cases these settings will be correct and do not have to be changed:Note: These settings are based on your service provider and country of operation. If you correctly configured your service provider information in the pervious step, these settings should be correct and do not need to be changed. In certain situations, some steps are left blank.12. If these settings appear to be correct, click the Next button to continue.Backup (Failover) / Primary Connection ConfigurationBased on the WWAN mode you chose in “Selecting the Proper WWAN Mode” on page 28, continue to one of the following two sections:• If you selected WWAN as a backup for the WAN Ethernet connection, continue to “Configuring WWAN as Failover” on page 30.• If you selected WWAN is my only connection to the Internet, continue to “Configuring LAN Settings” on page 34.Profile Name Choose a friendly name for this profile, or leave the name at default.Connection Type Verify the correct connection type is selected. For a complete list of connection types, refer to the latest SonicOS Administrator’s Guide.Dialed Number Verify the dial-out number your service provider requires to obtain a WWAN connection.User Name Verify the correct user name for your service provider (this field may be blank depending on your service provider).Password Verify the correct password for your service provider (this field may be blank depending on your service provider).Confirm Password Confirm the correct password for your service provider (this field may be blank depending on your service provider).APN Verify your access point name (this field may be blank depending on your service provider).
DRAFT not for productionPage 30 Configuring WWAN as FailoverComplete this section if you are using the WWAN wireless connection as a failover for your primary Internet connection. If you intend to use the WWAN wireless connection as your primary connection, skip this section and continue to “Configuring LAN Settings” on page 34.Selecting WAN Network Mode1. Select the correct type of network connection for your network:Note: The Setup Wizard automatically detects most networking modes. If it does not detect a networking mode, you may have a static IP address. See “Administrator Information” on page 6.Select from the following:2. Click the Next button to continue.3. Based on your WAN Network Mode, continue to one of the following sections:• If you selected Static IP, continue to “Static IP” on page 31.• If you selected DHCP, continue to “DHCP” on page 31.• If you selected PPPoE, continue to “PPPoE” on page 32.• If you selected PPTP, continue to “PPTP” on page 33.Static IP Select Static IP if you want to give the SonicWALL TZ190 appli-ance a specific, unchanging IP address.DHCP Select DHCP if your ISP assigns your computer a dynamic IP address. DHCP is commonly used with cable modems.PPPoE Select PPPoE if your ISP requires a username and password to establish a connection and assign a dynamic address. PPPoE is commonly used with DSL modems.PPTP Select PPTP if you dial into a specific server and log into a VPN to establish a connection. With PPTP, you can have either a static or dynamic IP address.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 31Static IP1. Configure your Internet service provider settings:2. Click the Next button to continue.3. Continue to “Configuring LAN Settings” on page 34 to finish the Wizard.DHCP1. You do not need to enter any WAN networking settings if you selected DHCP. The network settings are provisioned automatically from a DHCP server. 2. Click the Next button to continue.3. Continue to “Configuring LAN Settings” on page 34 to finish the Wizard.SonicWALL WAN IP Address Enter a single, static IP address. This must be in the address range assigned to you by your ISP.WAN Subnet Mask Enter the subnet mask for your network, provided by your ISP. For example, 255.255.255.0.Gateway (Router) Address Enter the IP address of your Internet gateway, provided by your ISP.DNS Server Address Enter the IP address of the DNS server for your network, provided by your ISP.DNS Server Address #2 (optional) You can enter a secondary, back-up DNS server to use if the first one fails.
DRAFT not for productionPage 32 PPPoE1. Configure your Internet service provider settings:2. Click the Next button to continue.3. Continue to “Configuring LAN Settings” on page 34 to finish the Wizard.Obtain an IP Address Automatically Select this if your ISP assigns you a dynamic IP address.Use the following IP Address Select this if your ISP has assigned you a static IP address, and enter the address.PPPoE User Name Enter the user name for your Internet account. Your ISP may require you to enter your username in e-mail address format, including “@” and the domain name, for example, joe.user@sonicwall.com.PPPoE Password Enter the password for your Internet account.Inactivity Disconnect (minutes) Check this box if you want the SonicWALL TZ190 appliance to disconnect from the Internet if there is no traffic for the number of minutes you enter.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 33PPTP1. Configure your Internet service provider settings: 2. Click the Next button to continue.3. Continue to “Configuring LAN Settings” on page 34 to finish the Wizard.PPTP Server IP Address Enter the address of the PPTP server.PPTP User Name Enter your network user name.PPTP Password Enter your network password.Obtain an IP Address Automatically Select this if the server assigns you a dynamic IP address.Use the following IP Address Check this if you have been given a static IP address, and fill in the following three fields.SonicWALL WAN IP Address Enter the static IP address for your connection.WAN Subnet Mask Enter the subnet mask for your connection.Gateway (Router) Address Enter the address of your Internet Gateway.
DRAFT not for productionPage 34 Configuring LAN SettingsBy default, your SonicWALL TZ 190 Wireless is configured with a LAN network IP address, 192.168.168.168, and subnet mask, 255.255.255.0, which will work well for most installations. In most cases, you can leave the default LAN IP address and subnet mask unchanged.1. Configure as follows: Note: Record the LAN IP address in a safe place, this is the IP address you will use to access the SonicWALL TZ 190 Wireless management interface. 2. Click the Next button to continue.SonicWALL LAN IP Address Enter an IP address for the LAN interface of your SonicWALL TZ 190 appliance.Record the address: .LAN Subnet Mask Enter a subnet mask for your LAN interface.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 35Configuring DHCP SettingsThe LAN DHCP Settings screen allows you to configure the DHCP server in the SonicWALL TZ 190 Wireless to automatically distribute IP addressing information to computers and other network devices on your LAN. 3. Configure your LAN settings as follows:4. Click the Next button to continue.5. The Configuration Summary window displays. Take this opportunity to verify that your settings are correct.Note: Settings differ based on the role your WWAN plays in the network setup and based on your WWAN and LAN network settings. The settings below are for a configuration where the Cingular WWAN is the primary interface.6. Click the Apply button to save these changes. The SonicWALL TZ 190 Wireless appliance will reboot. This process may take several minutes.Enable DHCP Server on LAN Leave this checkbox checked to use the DHCP server in the SonicWALL TZ190 appliance security appliance. Do not select this option if you already have a DHCP server on your network, or if you want to require your network clients to have static IP addresses. LAN Address Range If you enabled the DHCP Server, enter a range of IP addresses in the same subnet as the LAN IP address, or leave the default range unchanged. The default DHCP range will work for most installations.
DRAFT not for productionPage 36 Verifying Your WWAN ConnectionThis section provides instructions to ensure proper connectivity of your SonicWALL TZ 190 appliance. This section contains the following sub-sections:• “WWAN Connection Status” on page 36• “Manage WWAN Connection” on page 37• “Check Internet Connectivity” on page 37Log Into the Management InterfaceThe SonicWALL TZ 190 Wireless appliance will redirect to the login page after rebooting. Use your new username and password to log into the appliance after reboot. Note: If you changed the LAN IP address of the SonicWALL TZ 190 Wireless appliance during the setup wizard, you may have to re-configure the IP settings on your computer to access the appliance. For more help with connection issues, turn to page 25.WWAN Connection StatusThe Network > Interfaces page allows you to view the current WWAN connection status.1. In the SonicWALL TZ 190 Wireless appliance management interface, navigate to Network > Interfaces.2. In the Interface Settings section, the WWAN interface line displays the current status as follows:6on hook Indicates that the WWAN card is present but not yet connected.connected and start-ing PPP authentication Indicates that the WWAN card is associated with and currently attempting a connection to the WWAN network.connected Indicates an active connection.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 37Manage WWAN ConnectionThe Connection Manager window allows you to connect, disconnect and view current WWAN connection status.1. In the SonicWALL TZ 190 Wireless appliance management interface, navigate to Network > Interfaces.2. In the Interface Settings section, under WWAN, click the Manage button.3. The Connection Manager windows displays your connection status.4. If the Connection Manager shows “disconnected”, click the Connect button. If a network is available, you will be connected to it.Check Internet ConnectivityThe final step to confirm your Internet connectivity is to launch a website, such as <www.sonicwall.com> in a browser, using a computer that is connected to the SonicWALL TZ 190 Wireless appliance and using the SonicWALL as its sole Internet connection.If the website displays, your SonicWALL TZ 190 Wireless is operational and connected to a valid WWAN service provider account.
DRAFT not for productionPage 38 Connecting the SonicWALL TZ 190 Wireless to Your NetworkYour SonicWALL TZ 190 Wireless is equipped with a DHCP server feature. If you enabled this feature in the Setup Wizard, your DHCP-enabled network clients will automatically be provisioned by the SonicWALL. No further setup is needed for these clients.Note: If you are not using DHCP, refer to the SonicOS Enhanced Administrator’s Guide for instructions on setting up your network.Congratulations! You have successfully completed set up of your SonicWALL TZ 190 Wireless appliance. For more detailed information on your SonicWALL TZ 190 Wireless feature set, refer to the latest version of the SonicOS Enhanced Administrator’s Guide.77InternetWWANSonicWALL TZ 190 Appliancewan opt3GTZ 190
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 39Configuring a Static IP AddressComplete the following section based on your operating system in order to configure your management computer with a static IP address:Windows XP 1. From the Start menu, highlight Connect To and then select Show All Connections.2. Open the Local Area Connection Properties window. 3. Double-click Internet Protocol (TCP/IP) to open the Internet Protocol (TCP/IP) Properties window. 4. Select Use the following IP address and type 192.168.168.50 in the IP address field. 5. Type 255.255.255.0 in the Subnet Mask field. 6. Click OK for the settings to take effect.Windows 20001. From your Windows Start menu, select Settings. 2. Open Network and Dial-up Connections. 3. Click Properties. 4. Highlight Internet Protocol (TCP/IP) and click Properties. 5. Select Use the following IP address and type 192.168.168.50 in the IP address field.6. Type 255.255.255.0 in the Subnet Mask field. 7. Click OK for the settings to take effect.Windows NT1. From the Start menu, highlight Settings and then select Control Panel.2. Open Network.3. Double-click TCP/IP in the TCP/IP Properties window.4. Select Specify an IP Address and type 192.168.168.50 in the IP address field.5. Type 255.255.255.0 in the Subnet Mask field. 6. Click OK, and then click OK again. 7. Restart the computer for the changes to take effect.
DRAFT not for productionPage 40 Safety Instructions and Regulatory InformationRegulatory Model/Type Product NameAPL18-046 TZ 190 WirelessMounting the SonicWALLMount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º F (40º C) is recommended.Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios, transmitters, and broadband amplifiersThe included power cord is intended for use in North America only. For European Union (EU) customers, a power cord is not included.Ensure that no water or excessive moisture can enter the unit.Allow unrestricted airflow around the unit and through the vents on the side of the unit. A minimum of 1 inch (25.44mm) clearance is recommended.Consideration must be given to the connection of the equipment to the supply circuit and the effect of overloading the circuits has minimal impact on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings must be used when addressing this concern.Lithium Battery WarningThe Lithium Battery used in the SonicWALL security appliance may not be replaced by the user. Return the SonicWALL security appliance to a SonicWALL-authorized service center for replacement with the same or equivalent type recommended by the manufacturer. If, for any reason, the battery or SonicWALL security appliance must be disposed of, do so following the battery manufacturer's instructions.Cable ConnectionsAll Ethernet and RS232 (Console) cables are designed for intra-building connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the SonicWALL is located. Power Supply InformationIf the power supply is missing from your SonicWALL product package, please contact SonicWALL Technical Support at 408-752-7819 for a replacement. This product should only be used with a UL listed power supply marked “Class 2” or “LPS”, with an output rated 12 VDC, minimum 1.66 A.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 41Weitere Hinweise zur MontageWählen Sie für die Montage einen Ort, der keinem direkten Sonnenlicht ausgesetzt ist und sich nicht in der Nähe von Wärmequellen befindet. Die Umgebungstemperatur darf nicht mehr als 40 °C betragen.Führen Sie die Kabel nicht entlang von Stromleitungen, Leuchtstoffröhren und Störquellen wie Funksendern oder Breitbandverstärkern.Das eingeschlossene Netzkabel ist für Gebrauch in Nordamerikas nur vorgehabt. Für Europaïsche Union (EU) Kunden, ist ein Netzkabel nicht eingeschlossen.Stellen Sie sicher, dass das Gerät vor Wasser und hoher Luftfeuchtigkeit geschützt ist.Stellen Sie sicher, dass die Luft um das Gerät herum zirkulieren kann und die Lüftungsschlitze an der Seite des Gehäuses frei sind. Hier ist ein Belüftungsabstand von mindestens 26 mm einzuhalten.Vergewissern Sie sich, dass das Gerät sicher im Rack befestigt ist. Insbesondere muss auf nicht direkte Anschlüsse an Stromquellen geachtet werden wie z. B. bei Verwendung von Mehrfachsteckdosen.Hinweis zur LithiumbatterieDie in der Internet Security Appliance von SonicWALL verwendete Lithiumbatterie darf nicht vom Benutzer ausgetauscht werden. Zum Austauschen der Batterie muss die SonicWALL in ein von SonicWALL autorisiertes Service-Center gebracht werden. Dort wird die Batterie durch denselben oder entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt. Beachten Sie bei einer Entsorgung der Batterie oder der SonicWALL Internet Security Appliance die diesbezüglichen Anweisungen des Herstellers.KabelverbindungenAlle Ethernet- und RS232-C-Kabel eignen sich für die Verbindung von Geräten in Innenräumen. Schließen Sie an die Anschlüsse der SonicWALL keine Kabel an, die aus dem Gebäude herausgeführt werden, in dem sich das Gerät befindet.Informationen zur StromversorgungSollte das Netzteil nicht im Lieferumfang der SonicWALL enthalten sein, wenden Sie sich diesbezüglich an den technischen Support von SonicWALL (Tel.: +1-408-752-7819). Dieses Produkt darf nur in Verbindung mit einem nach den Normen der Underwriter Laboratories, USA als „UL-gelistet“ zugelassenen Netzteil der Kategorie „Class 2“ oder „LPS“ verwendet werden. Ausgang: 12 VDC Gleichsspannung, mind. 1,66 A.
DRAFT not for productionPage 42 FCC Part 15 Class B NoticeNOTE:This equipment was tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. And, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference using one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from the receiver connection.• Consult SonicWALL for assistance.Complies with EN55022 Class B and CISPR22 Class B.*Refer to the label on the bottom of the unit for device information including Class A or Class B FCC information.North American Authorized ChannelsSonicWALL declares that the APL18-046 (FCC ID: QWU-046)(IC: 4408A-046) when sold in US or Canada is limited to CH1~CH11 by specified firmware controlled in the USA.FCC RF Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (7.9 inches) between the radiator (antenna) and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.For more information regarding the above statement, please contact SonicWALL, Inc. at:1143 Borregas Avenue, Sunnyvale, CA 94089-1306, 1-408-745-9600.Canadian Radio Frequency Emissions StatementThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à toutes la norme NMB-003 du Canada.
CANADA STATEMENT Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Note: This device has been designed to operate with an antenna having a maximum gain of 5 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The require antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication.
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 43VCCI StatementRegulatory Information for KoreaAll products with country code “” (blank) and “A” are made in the USA.All products with country code “B” are made in China.All products with country code "C" or "D" are made in Taiwan R.O.C.Ministry of Information and Telecommunication Certification Number
DRAFT not for production6RQLFZDOOWtPWRSURKODãXMHåHWHQWRAPL18-046MHYHVKRGČVH]iNODGQtPLSRåDGDYN\GDOãtPLStVOXãQêPLXVWDQRYHQtPLVPČUQLFH(6Undertegnede Sonicwall erklærer herved, at følgende XGVW\UAPL18-046 overholder de væsentlige krav og øvrige relevante NUDYLGLUHNWLY()Hiermit erklärt Sonicwall, dass sich das Gerät APL18-046 inÜbereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie (*EHILQGHW+HUHE\6RQLFZDOOGHFODUHVWKDWWKLV$3/LVLQcompliance with the essential requirements and other relevant SURYLVLRQVRI'LUHFWLYH(&Por medio de la presente Sonicwall declara que el APL18-046FXPSOHFRQORVUHTXLVLWRVHVHQFLDOHV\FXDOHVTXLHUDRWUDVGLVSRVLFLRQHVDSOLFDEOHVRH[LJLEOHVGHOD'LUHFWLYD&(Par la présente Sonicwall déclare que l'appareil APL18-046 est conforme aux exigences essentielles et aux autres dispositions SHUWLQHQWHVGHODGLUHFWLYH&(&RQODSUHVHQWH6RQLFZDOOGLFKLDUDFKHTXHVWR$3/ è conforme ai requisiti essenziali ed alle altre disposizioni SHUWLQHQWLVWDELOLWHGDOODGLUHWWLYD&(Šiuo Sonicwall deklaruoja, kad šis APL18-046 atitinka esminiusUHLNDODYLPXVLUNLWDV(%'LUHNW\YRVQXRVWDWDVHierbij verklaart Sonicwall dat het toestel APL18-046 in overeenstemming is met de essentiële eisen en de andere UHOHYDQWHEHSDOLQJHQYDQULFKWOLMQ(*Sonicwall declara que este APL18-046 está conforme com os requisitos essenciais e outras disposições da Directiva &(6RQLFZDOOWêPWRY\KODVXMHåH$3/VSD]iNODGQpSRåLDGDYN\DYãHWN\SUtVOXãQpXVWDQRYHQLD6PHUQLFH(66RQLFZDOOYDNXXWWDDWlWHQHWWl$3/W\\SSLQHQODLWHonGLUHNWLLYLQ(<ROHHOOLVWHQYDDWLPXVWHQMDVLWlNRVNHYLHQGLUHNWLLYLQPXLGHQHKWRMHQPXNDLQHQ6RQLFZDOOHUNOUHUKHUYHGDWXWVW\UHW$3/HULsamsvarmed de grunnleggende krav og øvrige relevante krav i direktiv ()Indoor Onl\Binnen slechtsD'intérieur Seulement Innen NurDell'interno Soltanto Indoor Somen teDe interior Solamente7KLVHTXLSPHQWPD\EHRSHUDWHGLQ%HWULHEGLHVHU$XVUVWXQJZLUGLQQHQHUODXEW/RSpUDWLRQGHFHWpTXLSHPHQWHVWSHUPLVHGDQV&RXQWU\DQGFKDQQHOVHOHFWLRQLVPDGHLQVRIWZDUH)ROORZXVHUGRFXPHQWDWLRQWRPDNHFRXQWU\DQGFKDQQHOVHWWLQJ/DQGXQG.DQDODXVZDKOVLQGLQ6RIWZDUHJHPDFKW)ROJHQ6LHVerbraucherdokumentation, um Land und Kanal zu machen, VHW]HQG/DVpOHFWLRQGHSD\VHWFDQDOHVWIDLWHGDQVOHORJLFLHO6XLYH]ODGRFXPHQWDWLRQGXWLOLVDWHXUSRXUIDLUHOHSD\VHWODFDQDOVpOHFWLRQAT B(&<&ZDK(( )I)RD(HUI(IT LT LU NLNO PL PT SK (S&HGB:/$15/$1*+]
DRAFT not for production SonicWALL TZ 190 Wireless Getting Started Guide Page 45 Copyright Notice© 2007 SonicWALL, Inc.All rights reserved.Under the copyright laws, this manual or the software described within, cannot be copied, in whole or part, without the written consent of the manufacturer, except in the normal use of the software to make a backup copy. The same proprietary and copyright notices must be affixed to any permitted copies as were affixed to the original. This exception does not allow copies to be made for others, whether or not sold, but all of the material purchased (with all backup copies) can be sold, given, or loaned to another person. Under the law, copying includes translating into another language or format.Specifications and descriptions subject to change without notice.Safety Information and Rack Installation Instructions © 2006 International Business Machines Corporation.TrademarksSonicWALL is a registered trademark of SonicWALL, Inc.IBM is a registered trademark of the IBM Corporation in the United States, other countries, or both.Microsoft Windows 98, Windows NT, Windows 2000, Windows XP, Windows Server 2003, Internet Explorer, and Active Directory are trademarks or registered trademarks of Microsoft Corporation.Netscape is a registered trademark of Netscape Communications Corporation in the U.S. and other countries. Netscape Navigator and Netscape Communicator are also trademarks of Netscape Communications Corporation and may be registered outside the U.S.Adobe, Acrobat, and Acrobat Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the U.S. and/or other countries.Firefox is a trademark of the Mozilla Foundation.Other product and company names mentioned herein may be trademarks and/or registered trademarks of their respective companies and are the sole property of their respective manufacturers.

Navigation menu