Sonicwall 08F Wireless 802.11 abgn Device User Manual User Man QWU 08F rev 1

Sonicwall, Inc. Wireless 802.11 abgn Device User Man QWU 08F rev 1

UserManual.wiki >

08F User Manual

User Man_QWU-08F_rev. 1

Quick Start Guide Check Package ContentsVerify that your package includes the following contents: SonicWALL NSA 220 or NSA 220W Series Appliance Ethernet Cable Standard Power Adaptor and Cord DB9 -> RJ45 (CLI) Cable * Wireless Antennas (3) included with NSA 220W only3Connect the SonicWALL NSA 220 series appliance to the network using standard Ethernet cables as shown in the illustration. 4In a Web browser, navigate to http://www.mysonicwall.com/.If you do not have a MySonicWALL account, click the Not a Registered User? link to create an account.Under the Quick Register section of your MySonicWALL account, enter the Activation Key or Serial Number of the SonicWALL NSA series appliance you are registering. Conrm your serial number, enter a friendly name for your appliance, and enter your authentication code in the Quick Register > Add New Product section. Click Register.2Using the computer connected to the LAN port of the SonicWALL NSA 220 series appliance, navigate to http://192.168.168.168/in a Web browser.The Setup Wizard takes you through several basic steps to get your SonicWALL NSA series appliance congured for your network. Power cords are included with units in North America only.1Connect the SonicWALL NSA ApplianceRegisterConﬁgure the Management Host & Setup WizardSonicWALL NSA Series AppliancesRegistration MUST be completed prior to connecting to the appliance. http://www.mysonicwall.comhttp://192.168.168.168/After the Setup Wizard, the appliance may reboot. Please wait a few minutes while the appliance reboots to save the updated settings.*wanX1lanX0lan wanInternet routeror modem InternetServiceProviderConnect the included power cable and adaptor, and plug into an appropriate outlet. lan120V AC (U.S.)The NSA 220 series appliance powers on and the orange “test” LED blinks during the boot sequence. Continue to Step 4 when the “test” LED is no longer lit. This process may take up to 2 minutes. 2 minhttp://192.168.168.168/http://192.168.168.168/With your computer connected to the X0 port on the SonicWALL appliance, congure your IP with an address on the 192.168.168.0/24, such as 192.168.168.20.securityon/actwlan10/100/act1000/actlan wanX3 X4 X5 X6X2X1X0W0U0/U1Network Security Appliance10/100/1000NSA 220wireless-N securityon/actwlan10/100/act1000/actlan wanX3 X4 X5 X6X2X1X0W0U0/U1Network Security Appliance10/100/1000NSA 220wireless-N securityon/actwlan10/100/act1000/actlan wanX3 X4 X5 X6X2X1X0W0U0/U1Network Security Appliance10/100/1000NSA 220wireless-N CMYCMMYCYCMYK232-002003-50_Rev_A_SonicWALL_NSA_220_Series_Quick_Start_Poster_Inside.pdf 1 9/20/2011 7:50:50 PM

Safety and Regulatory Information for the SonicWALL NSA 220W Wireless Appliance Regulatory Model/Type Product Name APL24-08F NSA 220W Mounting the SonicWALL  Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º F (40º C) is recommended.  Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios, transmitters, and broadband amplifiers  The included power cord is intended for use in North America only. For European Union (EU) customers, a power cord is not included.  Ensure that no water or excessive moisture can enter the unit.  Allow unrestricted airflow around the unit and through the events on the side of the unit. A minimum of 1 inch (25.44mm) clearance is recommended.  Consideration must be given to the connection of the equipment to the supply circuit and the effect of overloading the circuits has minimal impact on over current protection and supply wiring. Appropriate consideration of equipment nameplate ratings must be used when addressing this concern. Cable Connections All Ethernet and RS232 (Console) cables are designed for intrabuilding connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the SonicWALL is located. Power Supply Information for APL24-08F If the power supply is missing from your SonicWALL product package, please contact SonicWALL Technical Support at408-752-7819 for a replacement. This product should only be used with a UL listed power supply marked “Class 2” or “LPS”, with an output rated 12 VDC, minimum 3.0 A, Tma: minimum40 degrees C. 

SonicWALL Sicherheit und gesetzliche Vorschriften Weitere Hinweise zur Montage  Wählen Sie für die Montage einen Ort, der keinem direktenSonnenlicht ausgesetzt ist und sich nicht in der Nähe vonWärmequellen befindet. Die Umgebungstemperatur darfnicht mehr als 40 °C betragen.  Führen Sie die Kabel nicht entlang von Stromleitungen,Leuchtstoffröhren und Störquellen wie Funksendern oderBreitbandverstärkern.  Das beigefügte Netzkabel ist nur für den Betrieb inNordamerika vergesehen. Für Kunden in der EuropäischenUnion ist kein Kabel beigefügt.  Stellen Sie sicher, dass das Gerät vor Wasser und hoher Luftfeuchtigkeit geschützt ist.  Stellen Sie sicher, dass die Luft um das Gerät herum zirkulieren kann und die Lüftungsschlitze an der Seite desGehäuses frei sind. Hier ist ein Belüftungsabstand vonmindestens 26 mm einzuhalten.  Vergewissern Sie sich, dass das Gerät sicher im Rackbefestigt ist. Kabelverbindungen Alle Ethernet- und RS232-C-Kabel eignen sich für dieVerbindung von Geräten in Innenräumen. Schließen Sie an dieAnschlüsse der SonicWALL keine Kabel an, die aus dem Gebäude herausgeführt werden, in dem sich das Gerät befindet. Informationen zur Stromversorgung APL24-08F Sollte das Netzteil nicht im Lieferumfang der SonicWALLenthalten sein, wenden Sie sich diesbezüglich an dentechnischen Support von SonicWALL (Tel.: +1-408-752-7819).Dieses Produkt darf nur in Verbindung mit einem nach denNormen der Underwriter Laboratories, USA als „UL-gelistet“zugelassenen Netzteil der Kategorie „Class 2“ oder „LPS“verwendet werden. Ausgang: 12 VDC Gleichsspannung, mind.3.0 A, Tma: mind. 40 Grad C. For more information regarding these statements, please contact SonicWALL, Inc. at: 2001 Logic Drive, San Jose, CA 95124-3452 1-408-745-9600 FCC NOTE: This equipment was tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. And, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If thee quipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference using one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and the receiver.  Connect the equipment into an outlet on a circuit different from the receiver connection.  Consult SonicWALL for assistance. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (7.9 inches) between the radiator (antenna)and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. United States of America Authorized Channels SonicWALL declares that the APL24-08F (FCC ID: QWU-08F) when sold in US is limited to CH1~CH11 by specified firmware controlled in the USA. FCC Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: This device is for indoor usage to reduce potential for harmful interference to co-channel systems. Frequency and channels in 5.15-5.2 GHz band are restricted to indoor use by the FCC. The APL24-08F device has been designed to operate with an antenna having a maximum gain of 2.5 dBi (2.4 and 5 GHz) RTNC connector and 3 dBi (2.4 and 5 GHs) RSMA connector. Antenna having a higher gain is strictly prohibited. The required antenna impedance is 50 ohms. Dynamic Frequency Selection(DFS) is required on all Wireless LAN Mater devices(usually Access Points) and Wireless LAN Clients (usually Wireless NICs) that operate within 5470 MHz – 5725 MHz. NSA 220W that have these frequencies and channels enable in this range comply with North American and International DFS requirements. Some frequencies are blocked, and cannot be selected by theuser per each specific regional approval. Specific to the USA; at the urging of the Federal Communication Commission(FCC) user/installers should avoid operation frequencies near Terminal Doppler Weather Radar (TDWR) systems frequencies 5600-5650 MHz when installing NSA 220W within 35 km of line-of-site of TDWR sites. If TDWR is within 35 km the NSA 220Wt frequencies should be set to at least 30 MHz above or below any TDWR system frequency at that site. TDWR locations and specific frequencies used can be found at <http://spectrumbridge.com/udrs/home.aspx>. Detailed current and background information can be found at <http://www.wispa.org/?page_id=2341>. DFS band function is product dependent. Some products may not have DFS band function. Industry Canada Notices Authorized Channels SonicWALL declares that the APL24-08F (IC: 4408A-08F) when sold in Canada is limited to CH1~CH11 by specified firmware controlled in theUSA. Operation This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesiredoperation. Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed andoperated with minimum distance 20cm between the radiator & your body. Antenna Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (IC: 4408A-08F) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having again greater than the maximum gain indicated

for that type, are strictly prohibited for use with this device. Approved Antenna RTNC connector, Type: Dipole Maximum Gain 2.5 dBi 2.4 and 5 GHz, Required Impedance: 50 ohms RSMA connector, Type: Dipole Maximum Gain 3 dBi (2.4 and 5 GHs) Required Impedance: 50 ohms Caution: (DFS band use) (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 52505350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 57255825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Industrie Canada Notifications Chaînes autorisées SonicWALL déclare que l'APL24-08F (IC : 4408A-08F) une fois vendu au Canada est limité à CH1~CH11 par spécifique microprogrammé aux Etats-Unis. Opération Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Déclaration de l'exposition aux radiations Cet équipement est conforme à l'exposition aux rayonnements IC limites établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre le radiateur et votre corps. Antenne Conformément à la réglementation d'Industrie Canada, le present émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent émetteur radio (IC:4408A-08F) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés cidessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Antenne approuvée RTNC Connecteur d'antenne Type: Dipole Gain Maximum: 2.5 dBi at 2.4 and 5 GHz, Impédance Requise: 50 ohms RSNA Connecteur d'antenne Type: Dipole Gain Maximum: 3.0 dBi at 2.4 and 5 GHz, Impédance Requise: 50 ohms

Attention: (utilisation de bande DFS) (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e.; (iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. NCC Statement

EU and EFTA This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio link sand/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Declaration of Conformity Application of council Directive 2004/108/EC (EMC)2006/95/EC (LVD)1999/5/EC (R&TTE) Standard(s) to which conformity is declared EN 55022:1998 +A1 +A2 Class B EN 55024:1998, +A2 EN 61000-3-2:2000, +A2 EN 61000-3-3:1995, +A2 EN 60950-1:2006, +A11:2009 National Deviations: AR, AT, AU, BE, CA, CH, CN, CZ, DE, DK, FI, FR, GB, GR, HU, IL, IN, IT, JP, KE, KR, MY, NL, NO, PL, SE, SG, SI, SK, US EN 300 328 V1.7.1:2006 EN 301 893 V1.5.1:2008 EN 301 489 V1.8.1:2008 EN 301 489-17 V2.1.1:2009a EN 50385:2002 Manufacturer/Responsible Party SonicWALL, Inc. 2001 Logic Drive San Jose, California 95124-3452 USA Type of Equipment Ethernet Firewall/VPN/Router with RLAN/WLAN 802.11a/b/g/n Type Numbers APL24-08F May be Marketed as NSA 220W I, the undersigned, hereby declare that the equipment specified above conforms to the above Directives and Standards. Quality control procedures will ensure series production of equipment will be compliant. Signature /s/ Larry Wagner_________ Date 10/19/11 Sr. Engineering Director

SonicWALL tímto prohlašuje, že tento APL24-08F je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Undertegnede SonicWALL erklærer herved, at følgende udstyr APL24-08F overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Hiermit erklärt SonicWALL, dass sich das Gerät APL24-08F in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Käesolevaga kinnitab SonicWALL seadme APL24-08F vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Hereby, SonicWALL, declares that this APL24-08F is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Por medio de la presente SonicWALL declara que el APL24-08F cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ SonicWALL ΔΗΛΩΝΕΙ ΟΤΙ APL24-08F ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Par la présente SonicWALL déclare que l'appareil APL24-08F est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Con la presente SonicWALL dichiara che questo APL24-08F è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar šo SonicWALL deklarē, ka APL24-08F atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Šiuo SonicWALL deklaruoja, kad šis APL24-08F atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart SonicWALL dat het toestel APL24-08F in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hawnhekk, SonicWALL, jiddikjara li dan APL24-08F jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Alulírott, SonicWALL nyilatkozom, hogy a APL24-08F megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Niniejszym SonicWALL oświadcza, że APL24-08F jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. SonicWALL declara que este APL24-08F está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. SonicWALL izjavlja, da je ta APL24-08F v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. SonicWALL týmto vyhlasuje, že APL24-08F spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. SonicWALL vakuuttaa täten että APL24-08F tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Härmed intygar SonicWALL att denna APL24-08F står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Navigation menu