Sony Group BTMS1 Bluetooth Module User Manual BC05 Module SPEC

Sony Corporation Bluetooth Module BC05 Module SPEC

Contents

BTM-S1_User manual_REV1

BC05 Module Spec. Shenzhen Synchron Electronics Co.,Ltd. 2010.11 1.General Description and Spcification 1.1 General Description This product is a Class 2 SMT Bluetooth Module used CSR BC5-MultiMedia External. It provides data and voice communications. It interfaces with a host through USB or UART and support data rate up to 12M/3Mbps. General Fetures: ■ Class 2 Bluetooth Module ■ Bluetooth Spec. V2.1+EDR Compliant ■ Support Firmware Upgrade ■ USB 2.0 and UART Host Interface ■ Multi-Configurable I2S, PCM or SPDIF Interface ■ Integrated 1.5V and 1.8V Linear Regulators ■ Integrated Switched-mode Regulator ■ Integrated Battery Charger ■ Integrated Microphone bias& LED Driver ■ 64MIPS Kalimba DSP Co-processor ■ Built in 16-bit Stereo Codec- 95dB SNR for DAC ■ Enhanced Audibility and Noise Cancellation ■ Support for 802.11 Co-existence ■ Green (RoHS Compliant) 1.2 Device Details Radio ■ Common TX/RX terminal simplifies external matching; eliminates external antenna switch ■ BIST minimises production test time ■ Bluetooth v2.1 + EDR specification compliant Transmitter ■ 4dBm RF transmit power with level control from onchip 6-bit DAC over a dynamic range >30dB ■ Class 2 and Class 3 support without the need for an external power amplifier or TX/RX switch
Receiver ■ Receiver sensitivity of -70dBm ■ Integrated channel filters ■ Digital demodulator for improved sensitivity and cochannel rejection ■ Real-time digitised RSSI available on HCI interface ■ Fast AGC for enhanced dynamic range Baseband and Software ■ 16Mbit external Flash ■ 48Kbyte internal RAM, allows full-speed data transfer, mixed voice/data and full piconet support ■ Logic for forward error correction, header error control, access code correlation, CRC, demodulation, encryption bit stream generation, whitening and transmit pulse shaping ■ Transcoders for A-law, μ-law and linear voice from host and A-law, μ-law and CVSD voice over air Physical Interfaces ■ SPI with clock speeds up to 64MHz in Master mode and 32MHz in Slave mode ■ I2C master compatible interface ■ UART interface with programmable data rate up to 3Mbits/s with an optional bypass mode ■ USB v2.0 interface ■ Bi-directional serial programmable audio interface supporting PCM, I2S and SPDIF formats ■ Two LED drivers with faders Kalimba DSP ■ Very low power Kalimba DSP co-processor, 64MIPS, 24-bit fixed point core ■ SBC decode takes approximately 4mW power consumption while streaming music ■ Single-cycle MAC; 24 x 24-bit multiply and 56-bit accumulator ■ 32-bit instruction word, dual 24-bit data memory ■ 6K x 32-bit program RAM, 16K x 24-bit + 12K x 24- bit data RAM ■ 64-word x 32-bit program memory cache when executing from Flash Stereo Audio Codec ■ 16-bit internal stereo codec ■ Dual ADC and DAC for stereo audio ■ Integrated amplifiers for driving 16Ω speakers; no need for external components ■ Support for single-ended speaker termination and line output ■ Integrated low-noise microphone bias ■ ADC sample rates are 8, 11.025, 16, 22.05, 32 and 44.1kHz
■ DAC sample rates are 8, 11.025, 12, 16, 22.05, 24, 32, 44.1 and 48kHz Auxiliary Features ■ Power management includes digital shutdown and wake-up commands with an integrated low-power oscillator for ultra-low power Park/Sniff/Hold mode ■ On-chip regulators: 1.5V output from 1.8V to 2.7V input and 1.8V output from 2.7V to 4.5V input ■ On-chip high-efficiency switched-mode regulator; 1.8V output from 2.7V to 4.4V input ■ Power-on-reset cell detects low supply voltage ■ 10-bit ADC and 8-bit DAC available to applications ■ On-chip charger for lithium ion/polymer batteries 1.3 Specification Chipset CSR BC05 Multimedia Specification Version Bluetooth V2.1+EDR Power Class Class 2 Frequency Band 2400~2483.5MHz Max. Tx Power -6~+4dBm RX Sensitivity ＜-70dBm Distance >10m(No obstacle) Flash Size 16M Power Voltage 3.3V Supply Current <40mA Operation Temperature -10 ~ +45 ℃ Dimension 32mm(L)x 13.5 mm(W) x 1.2mm(H)
2.Package Information 2.1 Pinout Diagram Figure 1: BC05 Module Pinout(Top View)
2.2 Terminal Functions Pin Name Pin Number Description GND 1 Ground PIO4 2 PIO5 3 PIO6 4 PIO7 5 PIO8 6 Programmable input/output line AIO1 7 AIO0 8 Analogue programmable input/output RESET 9 System Reset(Low Active) GND 10 Ground GND 11 Ground PIO10 12 PIO11 13 PIO12 14 PIO13 15 Programmable input/output line GND 16 Ground VDD 17 Positive supply for SPI/PCM ports and PIO[15:4] and BC05 MM Flash Pads, Connect to 3.3V GND 18 Ground VDD_Flash 19 Positive supply for Flash Memory ,Connect to 3.3V VDD_USB 20 Positive supply for UART/USB ports +1.8V 21 Switch-mode power regulator output GND 22 Ground USB_DP 23 USB data plus with selectable internal 1.5k Ω pull-up resistor USB_DN 24 USB data minus WP# 25 Flash write protect(Low Active) GND 26 Ground UART_RX 27 UART data input UART_TX 28 UART data output PCM_IN 29 Synchronous data input PCM_SYNC 30 Synchronous data sync PCM_CLK 31 Synchronous data clock PCM_OUT 32 Synchronous data output SPI_CSB 33 Chip select for SPI, active low
SPI_MOSO 34 SPI data output SPI_CLK 35 SPI clock SPI_MOSI 36 SPI data intput VRE_IN 37 Take high to enable high-voltage linear regulator and switch-mode regulator VDD_BAT 38 Lithium ion/polymer battery positive terminal. Battery charger output and input to switch-mode regulator GND 39 Ground VDD_CHG 40 Battery charge LED1 41 LED0 42 LED Driver GND 43 Ground SPK_L_N 44 Speaker output negative, left SPK_L_P 45 Speaker output positive, left SPK_R_N 46 Speaker output negative, right SPK_R_P 47 Speaker output positive, right GND_S 48 Signal Ground MIC_BIAS 49 Microphone bias MIC_B_P 50 Microphone input positive, right MIC_B_N 51 Microphone input negative, right MIC_A_P 52 Microphone input positive, left MIC_A_N 53 Microphone input negative, left GND 54 Ground PIO0 55 PIO1 56 PIO2 57 PIO3 58 Programmable input/output line GND 59 Ground RF 60 Transmitter output/switched receiver input
2.3 Package Dimensions Figure 2: BC05 Module package Dimensions
3.Hardware Description 3.1 Block Diagram Figure 3: BC05 Module Block Diagram
3.2 RF Ports Figure 4: RF Ports Diagram RF_N and RF_P form a complementary balanced pair and are available for both transmit and receive. On transmit their outputs are combined using an external balun into the single-ended output required for the antenna. Similarly, on receive their input signals are combined internally. Both terminals present similar complex impedances that may require matching networks between them and the balun. An LC network, L4 and C17. This provides a DC bias for the BlueCore5-MM from the 1.5V rail. The BPF1 used to suppress the signal out of Bluetooth Frequency Band and enhance the EMC capacity. The DC level must be set at VDD_RADIO. 3.3 UART Ports BC05 Module UART interface provides a simple mechanism for communicating with other serial devices using the RS232 protocol. When BlueCore5‑Multimedia External is connected to another digital device, UART_RX and UART_TX transfer data between the two devices. The Baud rate of the UART ports: 1200 baud (≤2%Error) Minimum 9600 baud (≤1%Error) Baud rate Maximum 4Mbaud (≤1%Error)
3.4 USB Ports This is a full speed (12Mbits/s) USB interface for communicating with other compatible digital devices.BC05 Module acts as a USB peripheral, responding to requests from a master host controller such as a PC. As USB is a master/slave oriented system (in common with other USB peripherals), BlueCore5‑Multimedia External only supports USB Slave operation. 4. Green Products and RoHS Compliance 5. Reference 1) BlueCore5-Multimedia External Product Data Sheet, CS-101568-DSP4 (bc05-ds- 004P) 2) Specification of the Bluetootn System , Verion 2.1+EDR
COMPLIANCES Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. COMPLIANCES ii IC Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device Cet appareil est conforme aux normes RSS sans licenced's Industry Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas provoquer d' interf'erence, et (2) cet appareil doit accepter toutes les interf'erences, y compris celles susceptibles de de'clencher le fonctionnement involontaire de l'appareil. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la class B est conforme a la norme NMB-003 du Canada. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end host device use this module should marked "Contain FCC ID:AK8BTMS1"or "Contains Transmitter Module IC:409B-BTMS1"in the label of the host device.

Navigation menu