Sony Group MEXGS820BT Bluetooth Audio System User Manual MEX GS820BT
Sony Corporation Bluetooth Audio System MEX GS820BT
UserManual.wiki
>
Sony Group
>
MEXGS820BT User Manual
Users Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)7GB CALLEnter the call menu. Receive/end a call.Press and hold for more than 2 seconds to switch the BLUETOOTH signal. (back)Return to the previous display.MODE (page 12, 13, 17, 19)Receptor for the remote commanderNumber buttons (1 to 6)Receive stored radio stations. Press and hold to store stations.ALBUM /Skip an album for audio device. Press and hold to skip albums continuously. (Not available when a USB device in Android mode or iPod is connected.)Press to thumbs up, or to thumbs down in Pandora® (page 17). (repeat)(Not available when a USB device in Android mode is connected.) (shuffle)(Not available when a USB device in Android mode is connected.)MIC (page 19) (play/pause)EXTRA BASSReinforce bass sound in synchronization with the volume level. Press to change the EXTRA BASS setting: [1], [2], [OFF].AUX input jackDSPL (display)Change display items.SCRL (scroll)Press and hold to scroll a display item.USB portRESET (inner panel) (page 8)The VOL (volume) + button has a tactile dot.CALLEnter the call menu. Receive/end a call.SOUNDOpen the SOUND menu directly.MENUPress and hold to open the setup menu.///Select a setup item, etc.ENTEREnter the selected item.Press and hold for more than 2 seconds to establish or terminate the “Sony | Music Center” function./ (prev/next)+/– (album +/–)VOL (volume) +/–Remove the insulation film before use.RM-X231 Remote commander010COV.book Page 7 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-7.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)8GBDetaching the Front PanelYou can detach the front panel of this unit to prevent theft.1Press and hold OFF until the unit turns off, press the front panel release button , then pull the panel towards you to remove.Caution alarmIf you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used.Serial numbersMake sure the serial numbers on the bottom of the unit and the back of the front panel are matched correctly. Otherwise you cannot make BLUETOOTH pairing, connection and disconnection by NFC.Resetting the UnitBefore operating the unit for the first time, or after replacing the car battery or changing connections, you must reset the unit.Press RESET on the inner panel with a ball-point pen, etc., after detaching the front panel.NoteResetting the unit will erase the clock setting and some stored contents.Setting the Clock1Press MENU, rotate the control dial to select [GENERAL], then press it.2Rotate the control dial to select [SET CLOCK-ADJ], then press it.The hour indication flashes.3Rotate the control dial to set the hour and minute.To move the digital indication, press / (SEEK –/+).4After setting the minute, press MENU.The setup is complete and the clock starts.To display the clockPress DSPL.Checking the Battery VoltageYou can check the current battery voltage. (Not available while the source is off and the clock is displayed.)1Press DSPL repeatedly until the battery voltage display appears.Getting StartedAttaching the front panel010COV.book Page 8 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-8.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)9GBPreparing a BLUETOOTH DeviceYou can enjoy music, or perform handsfree calling depending on the BLUETOOTH compatible device such as a smartphone, cellular phone and audio device (hereafter “BLUETOOTH device” if not otherwise specified). For details on connecting, refer to the operating instructions supplied with the device.Before connecting the device, turn down the volume of this unit; otherwise, loud sound may result.By touching the control dial on the unit with an NFC* compatible smartphone, the unit is paired and connected with the smartphone automatically.* NFC (Near Field Communication) is a technology enabling short-range wireless communication between various devices, such as mobile phones and IC tags. Thanks to the NFC function, data communication can be achieved easily just by touching the relevant symbol or designated location on NFC compatible devices.For a smartphone with Android OS 4.0 or lower installed, downloading the app “NFC Easy Connect” available at Google Play™ is required. The app may not be downloadable in some countries/regions.1Activate the NFC function on the smartphone.For details, refer to the operating instructions supplied with the smartphone.2Touch the N-Mark part of the unit with the N-Mark part of the smartphone.Make sure that lights up on the display of the unit.To disconnect by One touchTouch the N-Mark part of the unit with the N-Mark part of the smartphone again.Notes• When making the connection, handle the smartphone carefully to prevent scratches.• One touch connection is not possible when the unit is already connected to two NFC compatible devices. In this case, disconnect either device, and make connection with the smartphone again.When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other. This unit can connect two BLUETOOTH devices (two cellular phones, or a cellular phone and an audio device).1Place the BLUETOOTH device within 1 m (3 ft) of this unit.2Press MENU, rotate the control dial to select [BLUETOOTH], then press it.3Rotate the control dial to select [SET PAIRING], then press it.4Rotate the control dial to select [SET DEVICE 1]* or [SET DEVICE 2]*, then press it. flashes while the unit is in pairing standby mode.* [SET DEVICE 1] or [SET DEVICE 2] will be changed to the paired device name after pairing is complete.5Perform pairing on the BLUETOOTH device so it detects this unit.Connecting with a Smartphone by One touch (NFC)Pairing and connecting with a BLUETOOTH device010COV.book Page 9 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-9.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)10GB6Select [MEX-GS820BT] (your model name) shown in the display of the BLUETOOTH device.If your model name does not appear, repeat from step 2.7If passkey* input is required on the BLUETOOTH device, input [0000].* Passkey may be called “Passcode,” “PIN code,” “PIN number” or “Password,” etc., depending on the device.When pairing is made, stays lit.8Select this unit on the BLUETOOTH device to establish the BLUETOOTH connection. or lights up when the connection is made.NoteWhile connecting to a BLUETOOTH device, this unit cannot be detected from another device. To enable detection, enter the pairing mode and search for this unit from another device.To start playbackFor details, see “Playing a BLUETOOTH Device” (page 15).To disconnect the paired devicePerform steps 2 to 4 to disconnect after this unit and the BLUETOOTH device are paired.To use a paired device, connection with this unit is required. Some paired devices will connect automatically.1Press MENU, rotate the control dial to select [BLUETOOTH], then press it.2Rotate the control dial to select [SET BT SIGNL], then press it.Make sure that lights up.3Activate the BLUETOOTH function on the BLUETOOTH device.4Operate the BLUETOOTH device to connect to this unit. or lights up.Icons in the display:To connect the last-connected device from this unitActivate the BLUETOOTH function on the BLUETOOTH device.To connect with the audio device, press SRC to select [BT AUDIO] and press (play/pause).To connect with the cellular phone, press CALL.NoteWhile streaming BLUETOOTH audio, you cannot connect from this unit to the cellular phone. Connect from the cellular phone to this unit instead.TipWith BLUETOOTH signal on: when the ignition is turned to on, this unit reconnects automatically to the last-connected cellular phone.MEX-GS820BT[0000]Input passkeyConnecting with a paired BLUETOOTH deviceLights up when handsfree calling is available by enabling the HFP (Handsfree Profile).Lights up when the audio device is playable by enabling the A2DP (Advanced Audio Distribution Profile).010COV.book Page 10 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-10.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)11GBTo install the microphoneFor details, see “Installing the microphone” (page 42).When an iPhone/iPod with iOS5 or later installed is connected to the USB port, the unit is paired and connected with the iPhone/iPod automatically.To enable BLUETOOTH Auto Pairing, make sure [SET AUTOPAIR] in [BLUETOOTH] is set to [ON] (page 25).1Activate the BLUETOOTH function on the iPhone/iPod.2Connect an iPhone/iPod to the USB port.Make sure that lights up on the display of the unit.Notes• BLUETOOTH Auto Pairing is not possible if the unit is already connected to two BLUETOOTH devices. In this case, disconnect either device, then connect the iPhone/iPod again.• If BLUETOOTH Auto Pairing is not established, see “Preparing a BLUETOOTH Device” (page 9).Connecting a USB Device1Turn down the volume on the unit.2Connect the USB device to the unit.To connect an iPod/iPhone, use the USB connection cable for iPod (not supplied).Connecting Other Portable Audio Device1Turn off the portable audio device.2Turn down the volume on the unit.3Connect the portable audio device to the AUX input jack (stereo mini jack) on the unit with a connecting cord (not supplied)*.* Be sure to use a straight type plug.4Press SRC to select [AUX].To match the volume level of the connected device to other sourcesStart playback of the portable audio device at a moderate volume, and set your usual listening volume on the unit.Press MENU, then select [SOUND] [SET AUX VOL] (page 24).Connecting with an iPhone/iPod (BLUETOOTH Auto Pairing)010COV.book Page 11 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-11.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)12GBListening to the RadioTo listen to the radio, press SRC to select [TUNER].1Press MODE to change the band (FM1, FM2, FM3, AM1 or AM2).2Press MENU, rotate the control dial to select [GENERAL], then press it.3Rotate the control dial to select [SET BTM], then press it.The unit stores stations in order of frequency on the number buttons.1Press MODE to change the band (FM1, FM2, FM3, AM1 or AM2).2Perform tuning.To tune manuallyPress and hold / (SEEK –/+) to locate the approximate frequency, then press / (SEEK –/+) repeatedly to finely adjust to the desired frequency.To tune automaticallyPress / (SEEK –/+).Scanning stops when the unit receives a station.1While receiving the station that you want to store, press and hold a number button (1 to 6) until [MEM] appears.1Select the band, then press a number button (1 to 6).Using Radio Data System (RDS)1Press PTY during FM reception.2Rotate the control dial until the desired program type appears, then press it.The unit starts to search for a station broadcasting the selected program type.Type of programsThe CT data from the RDS transmission sets the clock.1Set [SET CT] in [GENERAL] to [CT-ON] (page 22).Listening to the RadioStoring automatically (BTM)TuningStoring manuallyReceiving the stored stationsSelecting program types (PTY)NEWS (News), INFORM (Information), SPORTS (Sports), TALK (Talk), ROCK (Rock), CLS ROCK (Classic Rock), ADLT HIT (Adult Hits), SOFT RCK (Soft Rock), TOP 40 (Top 40), COUNTRY (Country), OLDIES (Oldies), SOFT (Soft), NOSTALGA (Nostalgia), JAZZ (Jazz), CLASSICL (Classical), R & B (Rhythm and Blues), SOFT R&B (Soft Rhythm and Blues), LANGUAGE (Foreign Language), REL MUSC (Religious Music), REL TALK (Religious Talk), PERSNLTY (Personality), PUBLIC (Public), COLLEGE (College), HABL ESP (Spanish Talk), MUSC ESP (Spanish Music), HIP HOP (Hip-Hop), WEATHER (Weather)Setting clock time (CT)010COV.book Page 12 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-12.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)13GBListening to the SiriusXM RadioOnly SiriusXM brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Connect Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.comAfter installing your SiriusXM Connect Vehicle Tuner and antenna, press SRC to select [SIRIUSXM]. You should be able to hear the SiriusXM preview channel on Channel 1. After verifying that you can hear the preview channel, select Channel 0 to find the Radio ID of your tuner. In addition, the Radio ID is located on the bottom of the SiriusXM Connect Vehicle Tuner and its packaging. You will need this number to activate your subscription. Write the number down for reference.In the USA, you can activate online or by calling SiriusXM Listener Care:•Online:Visit www.siriusxm.com/activatenow• Phone: Call 1-866-635-2349In Canada, you can activate online or by calling SiriusXM Listener Care:•Online:Visit www.siriusxm.ca/activatexm• Phone: Call 1-877-438-9677As part of the activation process, the SiriusXM satellites will send an activation message to your tuner. When your radio detects that the tuner has received the activation message, your radio will display: [SUBSCRIPTION UPDATED - PRESS ENT TO CONTINUE]. Once subscribed, you can tune to channels in your subscription plan.Notes• The activation process usually takes 10 to 15 minutes, but may take up to an hour.• Your radio will need to be turned on and receiving the SiriusXM signal to receive the activation message.1Press (browse).2Rotate the control dial to select [CHANNEL], then press it.3Rotate the control dial to select the desired channel, then press it.To select channels with rapid browse modePress and hold or of remote commander more than 2 seconds after [CHANNEL] selected, then press ENTER.To select channels from categories1Press (browse).2Rotate the control dial to select [CATEGORY], then press it.3Rotate the control dial to select the desired category, then press it.The channel list appears.4Rotate the control dial to select the desired channel, then press it.To store channels1While receiving the channel that you want to store, press and hold a number button (1 to 6) until [MEM] appears.To receive the stored channel, press MODE to select the Band you want ([SX1], [SX2] or [SX3]), then press a number button (1 to 6). (Each Band can store up to 6 channels.)To set a parental controlThe parental control feature allows you to limit access to SiriusXM channels with mature content. When enabled, the parental control feature requires you to enter a passcode to tune to the locked channels. Information on setting up the passcode and locking channels can be found below.1Press MENU and rotate the control dial.2Select [GENERAL] [SXM PARENTAL] [LOCK SELECT] [LOCK-ON].Activating your SiriusXM Subscription Selecting channels for SiriusXM010COV.book Page 13 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-13.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)14GB3Enter the passcode by rotating the control dial on the unit or pressing / on the remote commander.To move the entry position, press / (SEEK –/+) on the unit or / on the remote commander.The initial passcode is [0000].4After entering the passcode, press ENTER.To unlock the channels, select [LOCK-OFF].To change the passcode1Press MENU and rotate the control dial.2Select [GENERAL] [SXM PARENTAL] [CODE EDIT].3Enter the current passcode on the current passcode input display, then press ENTER.The initial passcode is [0000].4Enter your new 4-digit passcode on the new passcode input display, then press ENTER.To change display itemsPress DSPL to change as follows:Channel Number (Default) Channel Name Artist Name Song Title Content Info Category Name Clock Battery VoltagePlaying a Disc1Insert the disc (label side up).Playback starts automatically.Playing a USB DeviceIn these Operating Instructions, “iPod” is used as a general reference for the iPod functions on an iPod and iPhone, unless otherwise specified by the text or illustrations.For details on the compatibility of your iPod, see “About iPod” (page 27) or visit the support site on the back cover.AOA (Android Open Accessory) 2.0, MSC (Mass Storage Class) and MTP (Media Transfer Protocol) type USB devices* compliant with the USB standard can be used. Depending on the USB device, the Android mode or MSC/MTP mode can be selected on the unit.Some digital media players or Android smartphones may require setting to MTP mode.* e.g., a USB flash drive, digital media player, Android smartphoneNotes• For details on the compatibility of your USB device, visit the support site on the back cover.• Smartphones with Android OS 4.1 or higher installed support Android Open Accessory 2.0 (AOA 2.0). However, some smartphones may not fully support AOA 2.0 even if Android OS 4.1 or higher is installed.For details on the compatibility of your Android smartphone, visit the support site on the back cover.Playback010COV.book Page 14 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-14.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)15GB• Playback of the following files is not supported.MP3/WMA/AAC/FLAC:–copyright-protected files– DRM (Digital Rights Management) files– Multi-channel audio filesMP3/WMA/AAC:– lossless compression filesWAV:– Multi-channel audio filesBefore making a connection, select the USB mode (Android mode or MSC/MTP mode) depending on the USB device (page 22).1Connect a USB device to the USB port (page 11).Playback starts.If a device is already connected, to start playback, press SRC to select [USB1] for the USB port on the front, [USB2] for the USB port on the rear ([IPD] appears in the display when the iPod is recognized).2Adjust the volume on this unit.To stop playbackPress and hold OFF for 1 second.To remove the deviceStop playback, then remove the device.Caution for iPhoneWhen you connect an iPhone via USB, phone call volume is controlled by the iPhone, not the unit. Do not inadvertently increase the volume on the unit during a call, as a sudden loud sound may result when the call ends.Playing a BLUETOOTH DeviceYou can play contents on a connected device that supports BLUETOOTH A2DP (Advanced Audio Distribution Profile).1Make BLUETOOTH connection with the audio device (page 9).To select the audio device, press MENU, then select [BLUETOOTH] [SET AUDIODEV] (page 25).2Press SRC to select [BT AUDIO].3Operate the audio device to start playback.4Adjust the volume on this unit.Notes• Depending on the audio device, information such as title, track number/time and playback status may not be displayed on this unit.• Even if the source is changed on this unit, playback of the audio device does not stop.• [BT AUDIO] does not appear in the display while running the “Sony | Music Center” application via the BLUETOOTH function.To match the volume level of the BLUETOOTH device to other sourcesStart playback of the BLUETOOTH audio device at a moderate volume, and set your usual listening volume on the unit.Press MENU, then select [SOUND] [SET BTA VOL] (page 24).Searching and Playing TracksNot available when a USB device in Android mode is connected.1During playback, press (repeat) or (shuffle) repeatedly to select the desired play mode.Playback in the selected play mode may take time to start.Available play modes differ depending on the selected sound source.Repeat play and shuffle play010COV.book Page 15 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-15.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)16GBNot available when a USB device in Android mode or iPod is connected.1During CD, USB or BT AUDIO*1 playback, press (browse)*2 to display the list of search categories.When the track list appears, press (back) repeatedly to display the desired search category.*1 Available only for audio devices supporting AVRCP (Audio Video Remote Control Profile) 1.4 or above.*2 During USB playback, press (browse) for more than 2 seconds to directly return to the beginning of the category list.2Rotate the control dial to select the desired search category, then press it to confirm.3Repeat step 2 to search the desired track.Playback starts.To exit the Quick-BrowZer modePress (browse).Not available when a USB device in Android mode or iPod is connected.1Press (browse).2Press (SEEK +).3Rotate the control dial to select the item.The list is jumped in steps of 10% of the total number of items.4Press ENTER to return to the Quick-BrowZer mode.The selected item appears.5Rotate the control dial to select the desired item, then press it.Playback starts.Pandora® is available to stream music through your iPhone and Android smartphone. You can control Pandora® on a BLUETOOTH connected iPhone/Android smartphone from this unit.Pandora® is only available in certain countries. Please visit http://www.pandora.com/legal for more information.Setting up Pandora®1Check the compatibility of your mobile device by visiting the support site on the back cover.2Download the latest version of the Pandora® application from your smartphone’s app store. A list of compatible devices can be found atwww.pandora.com/everywhere/mobileStreaming Pandora®1Make BLUETOOTH connection with the audio device (page 9).To select the audio device, press MENU, then select [BLUETOOTH] [SET AUDIODEV] (page 25).2Press SRC to select [PANDORA].3Launch Pandora® application on your mobile device.4Press (play/pause) to start playback.If the device number appearsMake sure that the same numbers are displayed (e.g., 123456) in this unit and the mobile device, then press ENTER on this unit and select [Yes] on the mobile device.Searching a track by name (Quick-BrowZer™)Searching by skipping items (Jump mode)Listening to Pandora®010COV.book Page 16 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-16.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)17GBWhen activating the BLUETOOTH functionYou can adjust the volume level.Press MENU, then select [SOUND] [SET BTA VOL] (page 24).Available Operations in Pandora®“Thumbs Up” or “Thumbs Down” feedback allows you to personalize stations.1During playback, press (Thumbs Up) or (Thumbs Down).The station list allows you to easily select a desired station.1During playback, press (browse).2Press (SEEK +) to select the sorting order [BY DATE] or [A TO Z].3Rotate the control dial to select the desired station, then press it.Playback starts.The track currently being played can be bookmarked and stored in your Pandora® account.1During playback, press MODE.To use a cellular phone, connect it with this unit. You can connect two cellular phones to the unit. For details, see “Preparing a BLUETOOTH Device” (page 9).Receiving a Call1Press CALL when a call is received with a ringtone.The phone call starts.NoteThe ringtone and talker’s voice are output only from the front speakers.To reject the callPress and hold OFF for 1 second.To end the callPress CALL again.Making a CallYou can make a call from the phonebook or call history when a cellular phone supporting PBAP (Phone Book Access Profile) is connected.When two cellular phones are connected to the unit, select either phone.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [PHONE BOOK], then press it.“Thumbs” feedbackUsing the station listBookmarkingHandsfree Calling (via BLUETOOTH only)From the phonebook010COV.book Page 17 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-17.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)18GB3Rotate the control dial to select an initial from the initial list, then press it.4Rotate the control dial to select a name from the name list, then press it.5Rotate the control dial to select a number from the number list, then press it.The phone call starts.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [RECENT CALL], then press it.A list of the call history appears.3Rotate the control dial to select a name or phone number from the call history, then press it.The phone call starts.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [DIAL NUMBER], then press it.3Rotate the control dial to enter the phone number, and lastly select [ ] (space), then press ENTER*.The phone call starts.* To move the digital indication, press / (SEEK –/+).Note[_] appears instead of [#] on the display.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [REDIAL], then press it.The phone call starts.You can make a call by saying the voice tag stored in a connected cellular phone that has a voice dialing function.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [VOICE DIAL], then press it.Alternatively, press and hold VOICE for more than 2 seconds.3Say the voice tag stored on the cellular phone.Your voice is recognized, and the call is made.To cancel voice dialingPress VOICE.From the call historyBy phone number inputBy redialBy voice tags010COV.book Page 18 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-18.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)19GBAvailable Operations during CallTo adjust the ringtone volumeRotate the control dial while receiving a call.To adjust the talker’s voice volumeRotate the control dial during a call.To adjust the volume for the other party (Mic gain adjustment)Press MIC.Adjustable volume levels: [MIC-LOW], [MIC-MID], [MIC-HI].To reduce echo and noise (Echo Canceler/Noise Canceler Mode)Press and hold MIC.Settable mode: [EC/NC-1], [EC/NC-2].To switch between handsfree mode and handheld modeDuring a call, press MODE to switch the phone call audio between the unit and cellular phone.NoteDepending on the cellular phone, this operation may not be available.Sony | Music Center with iPhone/Android smartphoneDownloading the latest version of “Sony | Music Center” application is required from the App Store for iPhone or from Google Play for Android smartphone.Notes• For your safety, follow your local traffic laws and regulations, and do not operate the application while driving.• “Sony | Music Center” is an app for controlling Sony audio devices which are compatible with “Sony | Music Center”, by your iPhone/Android smartphone.• What you can control with “Sony | Music Center” varies depending on the connected device.• To make use of “Sony | Music Center” features, see the details on your iPhone/Android smartphone.• For further details on “Sony | Music Center,” visit the following URL: http://www.sony.net/smcqa/• Visit the website below and check the compatible iPhone/Android smartphone models.For iPhone: visit the App StoreFor Android smartphone: visit Google Play1Make the BLUETOOTH connection with iPhone/Android smartphone (page 9).To select the audio device, press MENU, then select [BLUETOOTH] [SET AUDIODEV] (page 25).2Launch the “Sony | Music Center” application.3Press MENU, rotate the control dial to select [SONY APP], then press it.4Rotate the control dial to select [CONNECT], then press it.Connection to iPhone/Android smartphone starts.For details on the operations on iPhone/Android smartphone, see the help of the application.Useful FunctionsEstablishing the Sony | Music Center connection010COV.book Page 19 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-19.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)20GBIf the device number appearsMake sure that the number is displayed (e.g., 123456), then select [Yes] on the iPhone/Android smartphone.To terminate connection1Press MENU, rotate the control dial to select [SONY APP], then press it.2Rotate the control dial to select [CONNECT], then press it.Selecting the source or applicationYou can operate to select the desired source or application on iPhone/Android smartphone.To select the sourcePress SRC repeatedly. Alternatively, press SRC, rotate the control dial to select the desired source, then press ENTER.To display the source listPress SRC.Announcement of various information by voice guide (Android smartphone only)When SMS, Twitter/Facebook/Calendar notifications, etc., are received, they are automatically announced through the car speakers.For details on settings, refer to the help of the application.Activating voice recognition (Android smartphone only)By registering applications, you can control an application by voice command. For details, refer to the help of the application.To activate voice recognition1Press and hold VOICE to activate voice recognition.2Say the desired voice command into the microphone when [Say Source or App] appears on the Android smartphone.Notes• Voice recognition may not be available in some cases.• Voice recognition may not work properly depending on the performance of the connected Android smartphone.• Operate under conditions where noise such as engine sound is minimized during voice recognition.Replying a message of SMS (Android smartphone only)You can reply a message by voice recognition.1Activate voice recognition, then input “Reply (reply).”The message input display appears on the “Sony | Music Center” application.2Input a reply message by voice recognition.The list of message candidates appears on the “Sony | Music Center” application.3Rotate the control dial to select the desired message, then press it.The message is sent out.Making sound and display settingsYou can adjust the settings relating to sound and display via iPhone/Android smartphone.For details on settings, refer to the help of the application.Using Siri Eyes FreeSiri Eyes Free allows you to use an iPhone handsfree by simply speaking into the microphone. This function requires you to connect an iPhone to the unit via BLUETOOTH. Availability is limited to iPhone 4s or later. Make sure that your iPhone is running the latest iOS version. You must complete BLUETOOTH registration and connection configurations for the iPhone with the unit in advance. For details, see “Preparing a BLUETOOTH Device” (page 9). To select the iPhone, press MENU, then select [BLUETOOTH] [SET AUDIODEV] (page 25).1Activate the Siri function on the iPhone.For details, refer to the operating instructions supplied with the iPhone.010COV.book Page 20 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-20.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)21GB2Press and hold VOICE for more than 2 seconds.The voice command display appears.3After the iPhone beeps, speak into the microphone.The iPhone beeps again, then Siri starts responding.To deactivate Siri Eyes FreePress VOICE.Notes• The iPhone may not recognize your voice depending on usage conditions. (For example, if you are in a moving car.)• Siri Eyes Free may not function properly, or the response time may lag in locations where iPhone signals are difficult to receive. • Depending on the iPhone’s operating condition, Siri Eyes Free may not function properly, or may quit.• If you play a track with an iPhone using the BLUETOOTH audio connection, when the track starts playback via BLUETOOTH, Siri Eyes Free automatically quits and the unit switches to the BLUETOOTH audio source.• When Siri Eyes Free is activated during audio playback, the unit may switch to the BLUETOOTH audio source even if you do not specify a track to play.• When connecting the iPhone to the USB port, Siri Eyes Free may not function properly, or may quit.• When connecting the iPhone to the unit via USB, do not activate Siri with the iPhone. Siri Eyes Free may not function properly, or may quit.• There is no audio sound while Siri Eyes Free is activated.Canceling the DEMO ModeYou can cancel the demonstration display which appears when the source is off and the clock is displayed.1Press MENU, rotate the control dial to select [GENERAL], then press it.2Rotate the control dial to select [SET DEMO], then press it.3Rotate the control dial to select [SET DEMO-OFF], then press it.The setting is complete.4Press (back) twice.The display returns to normal reception/play mode.Basic Setting OperationYou can set items in the following setup categories:General setup (GENERAL), Sound setup (SOUND), Display setup (DISPLAY), BLUETOOTH setup (BLUETOOTH), Sony | Music Center setup (SONY APP)1Press MENU.2Rotate the control dial to select the setup category, then press it.The items that can be set differ depending on the source and settings.3Rotate the control dial to select the options, then press it.To return to the previous displayPress (back).Settings010COV.book Page 21 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-21.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)22GBGeneral Setup (GENERAL)DEMO (demonstration)Activates the demonstration: [ON], [OFF].CLOCK-ADJ (clock adjust) (page 8)CAUT ALM (caution alarm)Activates the caution alarm: [ON], [OFF] (page 8). (Available only while the source is off and the clock is displayed.)BEEP (beep)Activates the beep sound: [ON], [OFF].AUTO OFF (auto off)Shuts off automatically after a certain time when the unit is turned off: [ON] (30 minutes), [OFF].STEERING (steering)Registers/resets the setting of the steering wheel remote control. (Available only while the source is off and the clock is displayed.)STR CONTROL (steering control)Selects the input mode of the connected remote control. To prevent a malfunction, be sure to match the input mode with the connected remote control before use.CUSTOM (custom)Input mode for the steering wheel remote controlPRESET (preset)Input mode for the wired remote control excluding the steering wheel remote control EDIT CUSTOM (edit custom)Registers the functions (SOURCE, ATT, VOL +/–, SEEK +/–, VOICE, ON HOOK, OFF HOOK) to the steering wheel remote control:Rotate the control dial to select the function you want to assign to the steering wheel remote control, then press it.While [REGISTER] is blinking, press and hold the button on the steering wheel remote control you want to assign the function to. When registration is complete, [REGISTERED] is displayed.To register other functions, repeat steps and .(Available only when [STR CONTROL] is set to [CUSTOM].)RESET CUSTOM (reset custom)Resets the setting of the steering wheel remote control: [YES], [NO].(Available only when [STR CONTROL] is set to [CUSTOM].)Notes• While making settings, only button operation on the unit is available. For safety, park your car before making this setting.• If an error occurs while registering, all the previously-registered information remains. Restart registration from the function wherethe error occurred.• This function may not be available on some vehicles. For details on the compatibility of your vehicle, visit the support site on the backcover.USB MODE (USB mode)Changes the USB mode: [ANDROID], [MSC/MTP].(Available only when the USB source is selected.)CT (clock time)Activates the CT function: [ON], [OFF].BTM (best tuning memory) (page 12)(Available only when the tuner is selected.)SXM PARENTAL (SiriusXM parental)Sets the parental lock to [ON], [OFF], and edits the passcode (page 13). (Available only when SiriusXM is selected.)SXM SIGNAL (SiriusXM signal)Displays the current status of the SiriusXM signal strength: [NO SIGNAL] (signal level 0), [WEAK] (signal level 1), [GOOD] (signal level 2), [EXCELLENT] (signal level 3)010COV.book Page 22 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-22.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)23GBSXM RESET (SiriusXM reset)Initializes the SiriusXM Connect Vehicle Tuner settings (preset channels/parental lock): [YES], [NO]. (Available only when SiriusXM is selected.)FIRMWARE (firmware)(Available only while the source is off and the clock is displayed.)Checks/updates the firmware version. For details, visit the support site on the back cover.FW VERSION (firmware version)Displays current firmware version.FW UPDATE (firmware update)Enters firmware update process: [YES], [NO].Updating the firmware takes a few minutes to complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device.Sound Setup (SOUND)This setup menu is not available when the source is off and the clock is displayed.C.AUDIO+ (ClearAudio+)Reproduces sound by optimizing the digital signal with the Sony recommended sound settings: [ON], [OFF].(Automatically sets to [OFF] when [EQ10 PRESET] is changed and/or [EXTRA BASS] is set to [1] or [2] and/or [DSO] is set to [LOW], [MID] or [HIGH].)EQ10 PRESET (EQ10 preset)Selects an equalizer curve from 10 equalizer curves or off:[OFF], [R&B], [ROCK], [POP], [HIP-HOP], [EDM], [JAZZ], [SOUL], [COUNTRY], [KARAOKE]*, [CUSTOM].The equalizer curve setting can be memorized for each source.* [KARAOKE] reduces the vocal sound but cannot fully remove it during playback. Also, using a microphone is not supported.EQ10 CUSTOM (EQ10 custom)Sets [CUSTOM] of EQ10.Selects the equalizer curve: [BAND1] 32 Hz, [BAND2] 63 Hz, [BAND3] 125 Hz, [BAND4] 250 Hz, [BAND5] 500 Hz, [BAND6] 1 kHz, [BAND7] 2 kHz, [BAND8] 4 kHz, [BAND9] 8 kHz, [BAND10] 16 kHz.The volume level is adjustable in 1 dB steps, from -6 dB to +6 dB.POSITION (listening position)F/R POS (front/rear position)Simulates a natural sound field by delaying the sound output from speakers to suit your position: [FRONT L] (front left), [FRONT R] (front right), [FRONT] (center front), [ALL] (center of your car), [CUSTOM] (position set by the advanced car audio settings on “Sony | Music Center”) [OFF] (no position set)ADJ POSITION (adjust position)Fine-tunes the listening position setting: [+3] – [CENTER] – [-3].(Available only when [F/R POS] is not set to [OFF] or [CUSTOM].)SW POS (subwoofer position) [NEAR] (near), [NORMAL] (normal), [FAR] (far)(Available only when [F/R POS] is set to other than [OFF].)DSO (dynamic stage organizer)Creates a more ambient sound as if there were speakers in the dashboard: [OFF], [LOW], [MID], [HIGH].(Automatically sets to [OFF] when [C.AUDIO+] is set to [ON].)BALANCE (balance)Adjusts the sound balance: [RIGHT-15] – [CENTER] – [LEFT-15].010COV.book Page 23 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-23.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)24GBFADER (fader)Adjusts the relative level: [FRONT-15] – [CENTER] – [REAR-15].DSEE (digital sound enhancement engine)Improves digitally compressed sound by restoring high frequencies lost in the compression process: [ON], [OFF].This setting can be memorized for each source other than the tuner.AAV (advanced auto volume)Adjusts the playback volume level of all playback sources to the optimum level: [ON], [OFF].RB ENH (rear bass enhancer)Enhances the bass sound by applying a low pass filter setting to the rear speakers. This function allows the rear speakers to work as a subwoofer if one is not connected.(Available only when [SW DIREC] is set to [OFF].)RBE MODE (rear bass enhancer mode)Selects the rear bass enhancer mode: [1], [2], [3], [OFF].LPF FREQ (low pass filter frequency)Selects the subwoofer cut-off frequency: [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].LPF SLOP (low pass filter slope)Selects the LPF slope: [1], [2], [3].SW DIREC (subwoofer direct connection)Adjusts the settings for the subwoofer connected to the rear speaker lead without a power amplifier.(Available only when [RBE MODE] is set to [OFF].)Be sure to connect a 4 Ω – 8 Ω subwoofer to either of the rear speaker leads. Do not connect a speaker to the other rear speaker lead.SW MODE (subwoofer mode) Selects the subwoofer mode: [1], [2], [3], [OFF].SW PHASE (subwoofer phase) Selects the subwoofer phase: [NORM], [REV].SW POS (subwoofer position)Selects the subwoofer position: [NEAR], [NORMAL], [FAR].(Available only when [F/R POS] is set to other than [OFF].)LPF FREQ (low pass filter frequency) Selects the subwoofer cut-off frequency: [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].LPF SLOP (low pass filter slope) Selects the LPF slope: [1], [2], [3].S.WOOFER (subwoofer)SW LEVEL (subwoofer level)Adjusts the subwoofer volume level: [+10 dB] – [0 dB] – [-10 dB].([ATT] is displayed at the lowest setting.)SW PHASE (subwoofer phase)Selects the subwoofer phase: [NORM], [REV].SW POS (subwoofer position)Selects the subwoofer position: [NEAR], [NORMAL], [FAR].(Available only when [F/R POS] is not set to [OFF].)LPF FREQ (low pass filter frequency)Selects the subwoofer cut-off frequency: [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].LPF SLOP (low pass filter slope)Selects the LPF slope: [1], [2], [3].HPF (high pass filter)HPF FREQ (high pass filter frequency)Selects the front/rear speaker cut-off frequency: [OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].HPF SLOP (high pass filter slope)Selects the HPF slope (effective only when [HPF FREQ] is set to other than [OFF]): [1], [2], [3].AUX VOL (AUX volume)Adjusts the volume level for each connected auxiliary device: [+18 dB] – [0 dB] – [-8 dB].This setting negates the need to adjust the volume level between sources.(Available only when the AUX is selected.)BTA VOL (BLUETOOTH audio volume)Adjusts the volume level for each connected BLUETOOTH device: [+6 dB] – [0 dB] – [-6 dB].This setting negates the need to adjust the volume level between sources.(Available only when the BT audio, application or Pandora® is selected.)010COV.book Page 24 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-24.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)25GBDisplay Setup (DISPLAY)DIMMER (dimmer)Changes the display brightness:[OFF], [ON], [AT] (auto), [CLK] (clock).([AT] is available only when the illumination control lead is connected, and the head light is turned on.)To set this function to be active only during a fixed period, select [CLK], then set the start and end times.– To set the brightness when the dimmer function is activated:Set [DIMMER] to [ON], then adjust [BRIGHTNESS]. – To set the brightness when the dimmer function is deactivated:Set [DIMMER] to [OFF], then adjust [BRIGHTNESS].The brightness setting is stored and applied when the dimmer function is activated or deactivated.BRIGHTNESS (brightness)Adjusts the display brightness. The brightness level is adjustable: [1] – [10].BUTTON-C (button color)Sets a preset color or customized color for the buttons.COLOR (color)Selects from 15 presets colors, 1 customized color.CUSTOM-C (custom color)Registers a customized color for the buttons.RGB RED, RGB GRN, RGB BLUEAdjustable color range: [0] – [32] ([0] cannot be set for all color ranges).DSPL-C (display color)Sets a preset color or customized color for the display.COLOR (color)Selects from 15 presets colors, 1 customized color.CUSTOM-C (custom color)Registers a customized color for the display.RGB RED, RGB GRN, RGB BLUEAdjustable color range: [0] – [32] ([0] cannot be set for all color ranges).SND SYNC (sound synchronization)Activates the synchronization of the illumination with the sound: [ON], [OFF].AUTO SCR (auto scroll)Scrolls long items automatically: [ON], [OFF].(Not available when the AUX or tuner is selected.)BLUETOOTH Setup (BLUETOOTH)PAIRING (pairing) (page 9)Connects up to two BLUETOOTH devices: [DEVICE 1], [DEVICE 2].[DEVICE 1] or [DEVICE 2] will be changed to the paired device name after pairing is complete.AUDIODEV (audio device)Selects the audio device.[*] appears on the device paired with [DEVICE 1] or the current A2DP compatible audio device.RINGTONE (ringtone)Selects whether this unit or the connected cellular phone outputs the ringtone: [1] (this unit), [2] (cellular phone).AUTO ANS (auto answer)Sets this unit to answer an incoming call automatically: [OFF], [1] (about 3 seconds), [2] (about 10 seconds).AUTOPAIR (auto pairing)Starts BLUETOOTH pairing automatically when iOS device version 5.0 or later is connected via USB: [ON], [OFF].BT SIGNL (BLUETOOTH signal) (page 10)Activates/deactivates the BLUETOOTH function.010COV.book Page 25 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-25.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)26GBBT INIT (BLUETOOTH initialize)Initializes all the BLUETOOTH related settings (pairing information, preset number, device information, etc.): [YES], [NO].When disposing the unit, initialize all the settings. (Available only while the source is off and the clock is displayed.)Sony | Music Center Setup (SONY APP)AUTO LAUNCH (auto launch)Activates the “Sony | Music Center” auto launch: [ON], [OFF].When [ON] is selected, “Sony | Music Center” will automatically connect after the BLUETOOTH connection is complete.CONNECT (connect) (page 19)Establish and terminate “Sony | Music Center” function (connection).Updating the FirmwareTo update the firmware, visit the support site on the back cover, then follow the online instructions.Notes• Using a USB device (not supplied) is required for updating the firmware. Store the updater in the USB device, and connect the device to the USB port, then perform the update operation.• Updating the firmware takes a few minutes to complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device.Precautions• Cool off the unit beforehand if your car has been parked in direct sunlight.• Do not leave the front panel or audio devices brought in inside the car, or it may cause malfunction due to high temperature in direct sunlight.• Power antenna (aerial) extends automatically.Moisture condensationShould moisture condensation occur inside the unit, remove the disc and wait for about an hour for it to dry out; otherwise the unit will not operate properly.To maintain high sound qualityDo not splash liquid onto the unit or discs.• Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight.• Before playing, wipe the discs with a cleaning cloth from the center out. Do not use solvents such as benzine, thinner, commercially available cleaners.Additional InformationNotes on discs010COV.book Page 26 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-26.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)31GBTroubleshootingThe following checklist will help you remedy problems you may encounter with your unit.Before going through the checklist below, check the connection and operating procedures.For details on using the fuse and removing the unit from the dashboard, see “Connection/Installation” (page 39).If the problem is not solved, visit the support site on the back cover.GeneralNo power is being supplied to the unit.If the unit is turned off and the display disappears, the unit cannot be operated with the remote commander.– Turn on the unit.The unit is turned off when playing at a high volume.The power from the power supply lead of the car may not be sufficient.– Check the power connection. If noproblem is found in the connection, make the power connection to the battery directly. If the situation does not improve, consult your nearest dealer.No sound or the sound is very low.The position of the fader control [FADER] is not set for a 2-speaker system.The volume of the unit and/or connected device is very low.– Increase the volume of the unit and connected device.No beep sound.An optional power amplifier is connected and you are not using the built-in amplifier.The contents of the memory have been erased.The reset button has been pressed.– Store again into the memory.The power supply lead or battery has been disconnected or not connected properly.Stored stations and correct time are erased.The fuse has blown.Makes a noise when the position of the ignition is switched.The leads are not matched correctly with the car’s accessory power connector.During playback or reception, the demonstration mode starts.If no operation is performed for 5 minutes with [DEMO-ON] set, the demonstration mode starts.– Set [DEMO-OFF] (page 22).The display disappears from/does not appear in the display window.The dimmer is set to [DIM-ON] (page 25).The display disappears if you press and hold OFF.– Press OFF on the unit until the display appears.The connectors are dirty (page 28).The display/illumination flashes.The power supply is not sufficient.– Check that the car battery supplies enough power to the unit. (The power requirement is 12 V DC.)The operation buttons do not function.The disc will not eject.The connection is not correct.– Check the connection of the unit.If the situation does not improve, press the reset button (page 8). The contents stored in memory are erased.For your safety, do not reset the unit while you are driving.010COV.book Page 31 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-31.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)32GBRadio receptionStations cannot be received.The sound is hampered by noises.The connection is not correct.– If your car has built-in radio antenna (aerial) in the rear/side glass, connect an REM OUT lead (blue/white striped) or accessory power supply lead (red) to the power supply lead of a car’s antenna (aerial) booster.– Check the connection of the car antenna (aerial).– If the auto antenna (aerial) will not extend, check the connection of the power antenna (aerial) control lead.Preset tuning is not possible.The broadcast signal is too weak.RDSPTY displays [- - - - - - - -].The current station is not an RDS station.RDS data has not been received.The station does not specify the program type.CD playbackThe disc does not play.Defective or dirty disc.The CD-R/CD-RW is not for audio use (page 27).MP3/WMA/AAC files cannot be played.The disc is incompatible with the MP3/WMA/AAC format and version. For details on playable discs and formats, visit the support site on the back cover.MP3/WMA/AAC files take longer to play than others.The following discs take a longer time to start playback.– A disc recorded with a complicated tree structure.– A disc recorded in Multi Session.– A disc to which data can be added.The sound skips.Defective or dirty disc.USB device playbackYou cannot play items via a USB hub.This unit cannot recognize USB devices via a USB hub.A USB device takes longer to play.The USB device contains files with a complicated tree structure.The sound is intermittent.The sound may be intermittent at a high-bit-rate.DRM (Digital Rights Management) files may not be playable in some cases.The audio file cannot be played.USB devices formatted with file systems other than FAT16 or FAT32 are unsupported.** This unit supports FAT16 and FAT32, but some USB device may not support all of these FAT. For details, refer to the operating instruction of each USB device or contact the manufacturer.Operations for skipping an album, skipping items (Jump mode), and searching a track by name (Quick-BrowZer) cannot be performed.These operations cannot be performed when a USB device in Android mode or iPod is connected.– Set [USB MODE] to [MSC/MTP] (page 22).– Remove the iPod.The USB mode of the device is not set to the appropriate mode.– Make sure that the USB mode of the device is set to MSC/MTP mode.The sound cannot be output during playback in Android mode.While the unit is in Android mode, the sound outputs only from the Android smartphone.– Check the status of the audio playback application on the Android smartphone.– Playback may not perform properly depending on the Android smartphone.010COV.book Page 32 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-32.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)33GBNFC functionOne touch connection (NFC) is not possible.If the smartphone does not respond to the touching.– Check that the NFC function of the smartphone is turned on.– Move the N-Mark part of the smartphone closer to the N-Mark part on this unit.– If the smartphone is in a case, remove it.NFC receiving sensitivity depends on the device.If One touch connection with the smartphone fails several times, make BLUETOOTH connection manually.BLUETOOTH functionThe connecting device cannot detect this unit.Before the pairing is made, set this unit to pairing standby mode.While connected to two BLUETOOTH devices, this unit cannot be detected from another device.– Disconnect either connection and search for this unit from another device.When the device pairing is made, set the BLUETOOTH signal output to on (page 10).Connection is not possible.The connection is controlled from one side (this unit or BLUETOOTH device), but not both.– Connect to this unit from a BLUETOOTH device or vice versa.The name of the detected device does not appear.Depending on the status of the other device, it may not be possible to obtain the name.No ringtone.Adjust the volume by rotating the control dial while receiving a call.Depending on the connecting device, the ringtone may not be sent properly.– Set [RINGTONE] to [1] (page 25).The front speakers are not connected to the unit.– Connect the front speakers to the unit. The ringtone is output only from the front speakers.The talker’s voice cannot be heard.The front speakers are not connected to the unit.– Connect the front speakers to the unit. The talker’s voice is output only from the front speakers.A call partner says that the volume is too low or high.Adjust the volume accordingly using Mic gain adjustment (page 19).Echo or noise occurs in phone call conversations.Lower the volume.Set EC/NC Mode to [EC/NC-1] or [EC/NC-2] (page 19).If the ambient noise other than the phone call sound is loud, try reducing this noise.E.g.: If a window is open and road noise, etc., is loud, shut the window. If an air conditioner is loud, lower the air conditioner.The phone is not connected.When BLUETOOTH audio is played, the phone is not connected even if you press CALL.– Connect from the phone.The phone sound quality is poor.Phone sound quality depends on reception conditions of cellular phone. – Move your car to a place where you can enhance the cellular phone’s signal if the reception is poor.010COV.book Page 33 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-33.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)34GBThe volume of the connected audio device is low (high).Volume level will differ depending on the audio device.– Adjust the volume of the connectedaudio device or this unit (page 24).The sound skips during playback of a BLUETOOTH audio device.Reduce the distance between the unit and the BLUETOOTH audio device.If the BLUETOOTH audio device is stored in a case which interrupts the signal, remove the audio device from the case during use.Several BLUETOOTH devices or other devices which emit radio waves are in use nearby.– Turn off the other devices.– Increase the distance from the otherdevices.The playback sound stops momentarily when the connection between this unit and the cellular phone is being made. This is not a malfunction.The connected BLUETOOTH audio device cannot be controlled.Check that the connected BLUETOOTH audio device supports AVRCP.Some functions do not work.Check if the connecting device supports the functions in question.A call is answered unintentionally.The connecting phone is set to answer a call automatically.Pairing failed due to a timeout.Depending on the connecting device, the time limit for pairing may be short.– Try completing the pairing within thetime.BLUETOOTH function cannot operate.Turn off the unit by pressing OFF for more than 2 seconds, then turn the unit on again.No sound is output from the car speakers during handsfree call.If the sound is output from the cellular phone, set the cellular phone to output the sound from the car speakers.Siri Eyes Free is not activated.Perform the handsfree registration for an iPhone that supports Siri Eyes Free.Set the Siri function on the iPhone to on.Cancel the BLUETOOTH connection with the iPhone and the unit, and reconnect.Sony | Music Center operationApplication name is mismatched with the actual application in “Sony | Music Center”.Launch the application again from the “Sony | Music Center” application.While running the “Sony | Music Center” application via BLUETOOTH, the display automatically switches to [BT AUDIO].The “Sony | Music Center” application or BLUETOOTH function has failed.Run the application again.The “Sony | Music Center” application is automatically disconnected when the display switches to [IPD].The “Sony | Music Center” application on iPhone/iPod does not support iPod playback.– Change the source of the unit to other than [IPD], then establish the “Sony | Music Center” connection (page 19).Pandora® operationPandora® connection is not possible.Shut down the Pandora® application on the mobile device, and then launch it again.010COV.book Page 34 Thursday, March 23, 2017 2:51 PMThe “Sony | Music Center” connection is automatically disconnected when the USB mode of the unit is changed to [ANDROID]. The Android smartphone is not supporting playback in Android mode. Set the USB mode of the unit to [MSC/MTP], then establish the “Sony | MusicCenter” connection (page 17).](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-34.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)35GBMessagesThe following messages may appear or flash during operation.INVALIDThe selected operation could be invalid.[USB MODE] cannot be changed during iPod playback.OUTPUT ERROR: There may be an internal malfunction.Check the connection. If the error message still remains on in the display, consult your nearest Sony dealer.READ: Now reading information.Wait until reading is complete and playback starts automatically. This may take some time depending on the file organization.TEMP CAUTION The thermal protector is activated. Reduce the volume. (underscore): The character cannot be displayed.For CD playback:CD ERROR: The disc cannot be played. The disc will be ejected automatically.Clean or insert the disc correctly, or make sure the disc is not blank or defective.CD NO DISC: There is no disc.Insert a disc containing playable files (page 28).CD NO MUSIC: There is no playable file. The disc will be ejected automatically.Insert a disc containing playable files (page 28).CD PUSH EJT: The disc could not be ejected properly.Press (eject). or : The beginning or the end of the disc has been reached.For USB device playback:HUB NO SUPRT: USB hubs are not supported.IPD STOP: iPod playback has finished.Operate your iPod/iPhone to start playback.NOT SUPPORT - ANDROID MODEA USB device not supporting AOA (Android Open Accessory) 2.0 is connected to the unit while [USB MODE] is set to [ANDROID].– Set [USB MODE] to [MSC/MTP] (page 22).USB ERROR: The USB device cannot be played.Connect the USB device again.USB NO DEV: A USB device is not connected or recognized.Make sure the USB device or USB cable is securely connected.USB NO MUSIC: There is no playable file.Connect a USB device containing playable files (page 29).USB NO SUPRT: The USB device is not supported.For details on the compatibility of your USB device, visit the support site on the back cover.USB OVERLOAD: The USB device is overloaded.Disconnect the USB device, then press SRC to select another source. The USB device has a fault, or an unsupported device is connected.010COV.book Page 35 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-35.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)38GBCODE ERRORThe entered passcode is incorrect.– Enter the correct passcode.– If you forget your passcode, perform “SET SXM RESET” in “GENERAL” (page 23). Note that performing “SXM RESET” will initialize all the SiriusXM settings and stored contents in the SiriusXM Connect Vehicle Tuner.NO SIGNALSiriusXM Connect Vehicle Tuner is having difficulty receiving the SiriusXM satellite signal.– Verify that your vehicle is outdoors with a clear view of the sky.– Verify that the SiriusXM magnetic mount antenna is mounted on a metal surface on the outside of the vehicle.– Move the SiriusXM antenna away from any obstructions.– Inspect the antenna cable for damage and kinks.– Consult the SiriusXM Connect Vehicle Tuner installation manual for more information on antenna installation.– Replace the antenna if the cable is damaged. SiriusXM products are available at your local car audio retailer or online atwww.shop.siriusxm.comSUBSCRIPTION UPDATED - PRESS ENT TO CONTINUEThe radio has detected a change in your SiriusXM subscription status.– Press ENTER to clear the message.If you have questions about your subscription, please contact SiriusXM.In the USA, visit www.siriusxm.com or call 1-866-635-2349.In Canada, visit www.siriusxm.ca or call 1-877-438-9677.For steering wheel remote control operation:ERROR: An error occurred during the function registration.Register again from the function where the error occurred (page 22).TIMEOUT: The function registration failed due to a timeout.Try completing the registration while [REGISTER] is blinking (about 6 seconds) (page 22).For firmware update operation:ERROR: The updater is not stored in the USB device.Store the updater in the USB device, then try again (page 26).NO DEVICE: The USB device containing the updater is not connected or recognized.Make sure the USB device is securely connected.Disconnect the USB device, then connect the device again.UPDATE ERROR - PRESS ENTER: Firmware update is not completed properly.Press ENTER to clear the message, then try again.During the update, do not turn the ignition to the OFF position, nor remove the USB device (page 26).If these solutions do not help improve the situation, consult your nearest Sony dealer.If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began.010COV.book Page 38 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-38.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: LeftMEX-GS820BT4-698-030-11(1)42GBSubwoofer Easy ConnectionYou can use a subwoofer without a power amplifier when it is connected to a rear speaker cord.NoteUse a subwoofer with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.Memory hold connectionWhen the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.Speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.To capture your voice during handsfree calling, you need to install the microphone .Cautions• It is extremely dangerous if the cord becomes wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations.• If airbags or any other shock-absorbing equipment is in your car, contact the store where you purchased this unit, or the car dealer, before installation.NoteBefore attaching the double-sided tape , clean the surface of the dashboard with a dry cloth.When using the steering wheel remote controlInstallation of the connection cable RC-SR1 (not supplied) is required before use.1To enable the steering wheel remote control, select [SET STEERING] [EDIT CUSTOM] to make the registration (page 22).When the registration completes, the steering wheel remote control becomes available.Front speakerSubwooferInstalling the microphoneUsing the wired remote controlClip (not supplied)010COV.book Page 42 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-42.png)
![E:\Works\4698030111\4698030111MEXGS820BTUC\01GB-MEX-GS820BTUC\040CD.fmmasterpage: RightMEX-GS820BT4-698-030-11(1)43GBNotes on installing the connection cable RC-SR1 (not supplied)• Refer to the support sites on the back cover for details, then connect each lead properly to the appropriate leads. Making an improper connection may damage the unit.• Depending on the type of car, be sure to insulate the unused leads with electrical tape for safety.• Do not connect this cable when the steering wheel remote control is not used.• Consulting the dealer or an experienced technician for help is recommended.When using the wired remote control1To enable the wired remote control, set [STR CONTROL] in [SET STEERING] to [PRESET] (page 22).InstallationBefore installing the unit, remove the protection collar and the bracket from the unit.1Pinch both edges of the protection collar , then pull it out.2Insert both release keys until they click, and pull down the bracket , then pull up the unit to separate.• Before installing, make sure the catches on both sides of the bracket are bent inwards 2 mm (3/32 in).• For Japanese cars, see “Mounting the unit in a Japanese car” (page 44).1Position the bracket inside the dashboard, then bend the claws outward for a tight fit.2Mount the unit onto the bracket , then attach the protection collar .Notes• If the catches are straight or bent outwards, the unit will not be installed securely and may spring out.• Make sure the 4 catches on the protection collar are properly engaged in the slots of the unit.Removing the protection collar and the bracketFace the hook inwards.Mounting the unit in the dashboardCAUTIONDo not touch the left side of the unit when removing from the dashboard. The heatsink on the left side of the unit remains hot right after use.182 mm (7 1/4 in)53 mm (2 1/8 in)Catch010COV.book Page 43 Thursday, March 23, 2017 2:51 PM](https://usermanual.wiki/Sony-Group/MEXGS820BT/User-Guide-3413987-Page-43.png)
