Sony Group PCWAA500 Wireless LAN Access Point User Manual PCWA A500

Sony Corporation Wireless LAN Access Point PCWA A500

Contents

Users Manual A

Operating Instructions5GHzWireless LAN AccessPointPCWA-A5004-658-124-11(1)© 2002 Sony Corporation
2WARNINGTo prevent fire or shock hazard, do notexpose the unit to rain or moisture.To avoid electrical shock, do not open thecabinet. Refer servicing to qualifiedpersonnel only.Owner’s RecordThe model and serial numbers are located on thebottom of the product. Record the serial number inthe space provided below. Refer to them wheneveryou call upon your Sony dealer regarding thisproduct.Model No. PCWA-A500Serial No.______________CAUTIONYou are cautioned that any changes ormodifications not expressly approved in thismanual could void your warranty.FCC ID: AK8PCWAA500Exposure to Radio Frequency Radiation.The radiated output power of the Wireless LANAccess Point is far below the FCC radio frequencyexposure limits.Nevertheless, the Wireless LAN Access Pointshall be used in such a manner that the potentialfor human contact during normal operation isminimized.NOTE:This equipment has been tested and found tocomply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonableprotection against harmful interference in aresidential installation. This equipment generates,uses, and can radiate radio frequency energy and,if not installed and used in accordance with theinstructions, may cause harmful interference toradio or communications. However, there is noguarantee that interference will not occur in aparticular installation. If this equipment doescause harmful interference to television reception,which can be determined by turning the equipmentoff and on, you are encouraged to try to correctthe interference by one or more of the followingmeasures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipmentand receiver.– Connect the equipment into an outlet on acircuit different from that to which the receiveris connected.– Consult the dealer or an experienced radio/TVtechnician for help.You are cautioned that any changes ormodifications not expressly approved in thismanual could void your authority to operate thisequipment.If you have questions about this product, call theSony Customer Information Center at1-877-760-7669; or write to the Sony CustomerInformation Center at 12451 Gateway Boulevard,Fort Myers, FL 33913. The number below is forFCC-related matters only.Declaration of ConformityTrade Name: SonyModel No: PCWA-A500Responsible Party: Sony Electronics Inc.Address: 680 Kinderkamack Road,Oradell, NJ 07649 USATelephone: 201-930-6972This phone number is for FCC-related mattersonly.This device complies with part 15 of the FCCRules.Operation is subject to the following twoconditions:(1) This device may not cause harmfulinterference, and(2) this device must accept any interferencereceived, including interference that may causeundesired operation.The supplied interface cable must be used with theequipment in order to comply with the limits for adigital device pursuant to Subpart B of Part 15 ofFCC Rules.
3NoteThe power outlet should be installed near theequipment and should be easily accessible.Safety InformationWARNING• Opening the unit, for whatever reason, couldlead to damages that are not covered by thewarranty.• Do not touch the device or accessories duringthunder storms. Electrical shock could result.• This device is made for use in the USA only.• For indoor use only.• While using the Access Point, do not cover it orturn it on its side. Do not cover the AccessPoint with objects such as magazines ornewspapers or use it in confined, enclosedplaces, such as the spaces between walls andfurniture. Further, do not turn the Access Pointon its side while using it. Either situation couldcause heat to build up inside the Access Point,leading to overheating and possible fire.• Carefully place the Ethernet cable, AC adapter,and other wiring. Personal injury or damage tothe Access Point could result from peopletripping over the Ethernet cable, AC adapter, orpower cord. Protect wiring by locating it inplaces where people do not walk.• Do not swing the AC adapter. Injury couldresult if the adapter strikes a person or fragilematerial, such as glass.• Keep the Access Point out of the reach ofchildren. Unforeseeable injury could resultfrom swallowing loose parts, etc.• Place the Access Point on a stable surface. Donot place the Access Point on wobbly or tiltedsurfaces. Tipping or falling could result ininjury.• When using wall mounting, make sure that thewall is strong enough to support the AccessPoint. The Access Point could fall if the wall isnot strong enough, leading to unforeseeableaccidents. Further, be careful not to drop theunit or the tools used for mounting it. Doing socould result in unforeseeable accidents.• Avoid locations that are directly exposed tosunlight or heaters.• Internal overheating could result in fire ordamage to the unit.• Make sure connectors are properly connected.– Do not insert any metallic objects inside theconnectors. Short-circuiting the pins couldcause fire or damage to the unit.– Be careful to insert connectors squarely.Crooked insertion could cause pins to short-circuit, possibly causing fire or damage tothe unit.• Use only the supplied AC adapter with yourSony Wireless LAN Access Point. Todisconnect your Wireless LAN Access Pointfrom the power supply, unplug the AC adapter.
4Program © 2001, 2002 Sony CorporationDocumentation © 2002 Sony CorporationCopyright © 2000-2001 AtherosCommunications, Inc., All Rights ReservedCopyright © 1994-2001 The NetBSD Foundation,Inc. All rights reserved.Redistribution and use in source and binary forms,with or without modification, are permittedprovided that the following conditions are met:1 Redistributions of source code must retain theabove copyright notice, this list of conditionsand the following disclaimer.2 Redistributions in binary form must reproducethe above copyright notice, this list ofconditions and the following disclaimer in thedocumentation and/or other materials providedwith the distribution.3 All advertising materials mentioning features oruse of this software must display the followingacknowledgement:This product includes software developed bythe NetBSD Foundation, Inc. and itscontributors.4 Neither the name of The NetBSD Foundationnor the names of its contributors may be used toendorse or promote products derived from thissoftware without specific prior writtenpermission.THIS SOFTWARE IS PROVIDED BY THENETBSD FOUNDATION, INC. ANDCONTRIBUTORS “AS IS” AND ANYEXPRESS OR IMPLIED WARRANTIES,INCLUDING, BUT NOT LIMITED TO, THEIMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE ARE DISCLAIMED.IN NO EVENT SHALL THE FOUNDATIONOR CONTRIBUTORS BE LIABLE FOR ANYDIRECT, INDIRECT, INCIDENTAL, SPECIAL,EXEMPLARY, OR CONSEQUENTIALDAMAGES (INCLUDING, BUT NOT LIMITEDTO, PROCUREMENT OF SUBSTITUTEGOODS OR SERVICES; LOSS OF USE, DATA,OR PROFITS; OR BUSINESSINTERRUPTION) HOWEVER CAUSED ANDON ANY THEORY OF LIABILITY, WHETHERIN CONTRACT, STRICT LIABILITY, ORTORT (INCLUDING NEGLIGENCE OROTHERWISE) ARISING IN ANY WAY OUTOF THE USE OF THIS SOFTWARE, EVEN IFADVISED OF THE POSSIBILITY OF SUCHDAMAGE.Copyright © 1993-2000 by Darren Reed.The author accepts no responsibility for the use ofthis software and provides it on an “as is” basiswithout express or implied warranty.Redistribution and use in source and binary formsare permitted provided that this notice is preservedand due credit is given to the original author andthe contributors.This program is distributed in the hope that it willbe useful, but WITHOUT ANY WARRANTY;without even the implied warranty ofMERCHANTABILITY or FITNESS FOR APARTICULAR PURPOSE.Copyright © 1980, 1986, 1989 Regents of theUniversity of California. All rights reserved.© UNIX System Laboratories, Inc.All or some portions of this file are derived frommaterial licensed to the University of Californiaby American Telephone and TelegraphCo. or Unix System Laboratories, Inc. and arereproduced herein with the permission of UNIXSystem Laboratories, Inc.Redistribution and use in source and binary forms,with or without modification, are permittedprovided that the following conditions are met:1 Redistributions of source code must retain theabove copyright notice, this list of conditionsand the following disclaimer.2 Redistributions in binary form must reproducethe above copyright notice, this list ofconditions and the following disclaimer in thedocumentation and/or other materials providedwith the distribution.3 All advertising materials mentioning features oruse of this software must display the followingacknowledgement:This product includes software developed bythe University of California, Berkeley and itscontributors.4 Neither the name of the University nor thenames of its contributors may be used toendorse or promote products derived from thissoftware without specific prior writtenpermission.THIS SOFTWARE IS PROVIDED BY THEREGENTS AND CONTRIBUTORS “AS IS”AND ANY EXPRESS OR IMPLIEDWARRANTIES, INCLUDING, BUT NOTLIMITED TO, THE IMPLIED WARRANTIESOF MERCHANTABILITY AND FITNESS FOR
5A PARTICULAR PURPOSE AREDISCLAIMED. IN NO EVENT SHALL THEREGENTS OR CONTRIBUTORS BE LIABLEFOR ANY DIRECT, INDIRECT, INCIDENTAL,SPECIAL, EXEMPLARY, ORCONSEQUENTIAL DAMAGES (INCLUDING,BUT NOT LIMITED TO, PROCUREMENT OFSUBSTITUTE GOODS OR SERVICES; LOSSOF USE, DATA, OR PROFITS; OR BUSINESSINTERRUPTION) HOWEVER CAUSED ANDON ANY THEORY OF LIABILITY, WHETHERIN CONTRACT, STRICT LIABILITY, ORTORT (INCLUDING NEGLIGENCE OROTHERWISE) ARISING IN ANY WAY OUTOF THE USE OF THIS SOFTWARE, EVEN IFADVISED OF THE POSSIBILITY OF SUCHDAMAGE.Copyright © 1995, 1996, 1997, 1998, 1999The Internet Software Consortium - DHCP. Allrights reserved.Redistribution and use in source and binary forms,with or without modification, are permittedprovided that the following conditions are met:1 Redistributions of source code must retain theabove copyright notice, this list of conditionsand the following disclaimer.2 Redistributions in binary form must reproducethe above copyright notice, this list ofconditions and the following disclaimer in thedocumentation and/or other materials providedwith the distribution.3 Neither the name of The Internet SoftwareConsortium - DHCP nor the names of itscontributors may be used to endorse or promoteproducts derived from this software withoutspecific prior written permission.THIS SOFTWARE IS PROVIDED BY THEINTERNET SOFTWARE CONSORTIUM ANDCONTRIBUTORS “AS IS” AND ANYEXPRESS OR IMPLIED WARRANTIES,INCLUDING, BUT NOT LIMITED TO, THEIMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE ARE DISCLAIMED.IN NO EVENT SHALL THE INTERNETSOFTWARE CONSORTIUM ORCONTRIBUTORS BE LIABLE FOR ANYDIRECT, INDIRECT, INCIDENTAL, SPECIAL,EXEMPLARY, OR CONSEQUENTIALDAMAGES (INCLUDING, BUT NOT LIMITEDTO, PROCUREMENT OF SUBSTITUTEGOODS OR SERVICES; LOSS OF USE, DATA,OR PROFITS; OR BUSINESSINTERRUPTION) HOWEVER CAUSED ANDON ANY THEORY OF LIABILITY, WHETHERIN CONTRACT, STRICT LIABILITY, ORTORT (INCLUDING NEGLIGENCE OROTHERWISE) ARISING IN ANY WAY OUTOF THE USE OF THIS SOFTWARE, EVEN IFADVISED OF THE POSSIBILITY OF SUCHDAMAGE.Copyright © 1999,2000 by Jef Poskanzer. Allrights reserved.Redistribution and use in source and binary forms,with or without modification, are permittedprovided that the following conditions are met:1 Redistributions of source code must retain theabove copyright notice, this list of conditionsand the following disclaimer.2 Redistributions in binary form must reproducethe above copyright notice, this list ofconditions and the following disclaimer in thedocumentation and/or other materials providedwith the distribution.THIS SOFTWARE IS PROVIDED BY THEAUTHOR AND CONTRIBUTORS “AS IS”AND ANY EXPRESS OR IMPLIEDWARRANTIES, INCLUDING, BUT NOTLIMITED TO, THE IMPLIED WARRANTIESOF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE AREDISCLAIMED. IN NO EVENT SHALL THEAUTHOR OR CONTRIBUTORS BE LIABLEFOR ANY DIRECT, INDIRECT, INCIDENTAL,SPECIAL, EXEMPLARY, ORCONSEQUENTIAL DAMAGES (INCLUDING,BUT NOT LIMITED TO, PROCUREMENT OFSUBSTITUTE GOODS OR SERVICES; LOSSOF USE, DATA, OR PROFITS; OR BUSINESSINTERRUPTION) HOWEVER CAUSED ANDON ANY THEORY OF LIABILITY, WHETHERIN CONTRACT, STRICT LIABILITY, ORTORT (INCLUDING NEGLIGENCE OROTHERWISE) ARISING IN ANY WAY OUTOF THE USE OF THIS SOFTWARE, EVEN IFADVISED OF THE POSSIBILITY OF SUCHDAMAGE.
6Table of contentsGetting startedOverview ............................................... 7What you can do with your WirelessLAN Access Point ..................... 7System requirements ..................... 8About the manuals and Help files ...8Names of parts and functions ................ 9About the Access Point initial settings 12To return the Access Point settingsto the factory default settings .. 13MAC address ............................... 13Setting and connectionsConfiguring the Access Pointsettings ............................................ 14Before configuring the Access Pointsettings ..................................... 14Displaying the Access Point setuppage .......................................... 16About the Access Pointpassword .................................. 18Configuring and changing settingsfor the Access Point ................. 19Confirming the firmware version forthe Access Point ...................... 20Confirming the status of the AccessPoint ......................................... 21Connecting ........................................... 22Connecting to a DSL modem, cablemodem, or ISDN router ........... 22Precautions when mounting the AccessPoint on a wall ................................ 24Additional informationPrecautions .......................................... 26Specifications ...................................... 27Getting help ......................................... 28Glossary ............................................... 29Troubleshooting ................................... 31Sony, VAIO, and the VAIO logo are trademarksof Sony Corporation.Microsoft and Windows are registeredtrademarks of Microsoft Corporation in theUnited States and other countries.Ethernet is a registered trademark of XeroxCorporation.All other trademarks are trademarks of theirrespective owners.• In this manual, Microsoft® Windows®Millennium Edition is referred to as WindowsMe.• In this manual, Microsoft® Windows® 2000Professional is referred to as Windows 2000.
7Getting startedOverviewWhat you can do with your Wireless LAN Access PointThe 5GHz Wireless LAN Access Point PCWA-A500 is designed forconstructing a wireless LAN (Local Area Network) environment. Becausethe wireless LAN does not require cable connections, client computers canoperate anywhere within a specified range.Connect your Access Point to a power outlet, insert the 5GHz WirelessLAN PC Card PCWA-C500 (sold separately) into your computer, and usethe provided software together with the Access Point to construct a wirelessLAN environment on multiple client computers (16 or fewer isrecommended). In a wireless LAN environment, you can share files andfolders on other client computers and let others share files and folders onyour computer.Further, you can connect the Access Point to a DSL modem, cable modem,or ISDN router to access the Internet from a client computer that isequipped with wireless LAN or from a client computer on an Ethernet LANthat is connected to the NETWORK 2 connector.POWERMESSAGEWIRELESSNETWORK 1NETWORK 2InternetInternetserviceprovider DSL modem/cable modem/ISDN routerTo the NETWORK 1connectorTo theNETWORK 2connectorHub
8System requirementsIn order to configure the Access Point or check Access Point settings, yourcomputer must satisfy the following hardware and software requirements.❑A computer installed with a 5GHz Wireless LAN PC Card(Make sure that the driver required to operate the PC card isinstalled correctly.)❑Web browser (The following browsers are recommended.)– Microsoft® Internet Explorer 5 or later– Netscape® Communicator 4.75 or laterNotes•Sony cannot assure trouble-free operation for all computers satisfying the specifiedsystem requirements.•To construct a wireless LAN environment, the 5GHz Wireless LAN PC CardPCWA-C500 (sold separately) is required.•Internet access requires the separate purchase of an Internet connection from an InternetService Provider (ISP).About the manuals and Help filesThe following manuals and Help files are provided with this product.•5GHz Wireless LAN Access Point PCWA-A500 Quick Start GuideThis guide contains simple explanations on how to set up and configurethe Access Point. We recommend reading the guide before using thisproduct.•5GHz Wireless LAN Access Point PCWA-A500 Operating Instructions(this manual)These instructions contain detailed explanations on how to setup andconfigure the Access Point.•Access Point Online HelpOnline help explains how to set up and use the Access Point. Toconfigure an Access Point, go to the Access Point setup page. Forinformation on how to display the Access Point setup page and onlinehelp, see “Displaying the Access Point setup page” (page 16).
9Getting startedNames of parts and functionsFront view Side viewPOWERMESSAGEWIRELESSNETWORK 1NETWORK 2214563NETWORK 2Lights green when an Ethernet cableis connected to the NETWORK 2connector.Flashes orange while data is beingexchanged using the NETWORK 2connector.z HintAll indicators except the POWER indicatorflash while the Access Point settings are beingchanged.3Stand/wall-mount adapterThe stand/wall-mount adapter isretractable and can be used with thearm extended straight down as a standor with the arm retracted as a wall-mount adapter.When extending the arm straightdown, it must not be fixed in aposition other than that shown in theillustration above.To get the best performance from thebuilt-in antenna, position the AccessPoint so that the front of the unitcreates a right angle with thesupporting surface.1Built-in antenna (not externallyvisible)2IndicatorsPOWERLights green while power is suppliedto the Access Point.MESSAGELights when unread logs exceed acertain size. The indicator goes outwhen the log is displayed.WIRELESSLights green when data can beexchanged on a wireless LAN.Flashes orange while data is beingexchanged on a wireless LAN.NETWORK 1Lights green when an Ethernet cableis connected to the NETWORK 1connector.Flashes orange while data is beingexchanged using the NETWORK 1connector.
104NETWORK 1 connectorUse an Ethernet cable to connect theAccess Point to a DSL modem, cablemodem, or ISDN router.5NETWORK 2 connectorUse an Ethernet cable to connect theAccess Point to an Ethernet LAN hub.6DC IN 10 V jackConnects to the AC power adapter.Rear viewNETWORK 1NETWORK 2DC IN 10VNETWORK 1NETWORK 2DC IN 10V9qa7807Ferrite core storage recessInsert the ferrite core of the ACadapter cable qd (on page 11) into thisrecess, then insert the cable into theAC adapter cable securing groove 8to fix it in place. For details, refer tothe Quick Start Guide.8AC adapter cable securing grooveInsert the ferrite core of the ACadapter cable qd (on page 11) into theferrite core storage recess 7, theninsert the cable into this groove to fixit in place. For details, refer to theQuick Start Guide.9Serial number labelThe serial number (SERIAL NO.) isprinted on this label. The numbersprinted below “NO.” are the serialnumber.0Wall-mounting holesWhen using the stand/wall-mountadapter as a wall-mount adapter, youcan mount the Access Point onto thewall by screwing two screws into theholes. (The screws for mounting theAccess Point are not provided. Makesure you use a product that is rated tosupport the weight of the AccessPoint.)When mounting the Access Point on awall, see “Precautions when mountingthe Access Point on a wall” (page 24).qa ID labelThis label is printed with the IDassigned to the Access Point at thetime of shipping. (This ID is alsoreferred to as the Network Name(SSID).) This ID is required whenconfiguring Access Point settings.
11Getting startedqsqs Factory default switchUse this switch to return the AccessPoint settings to the factory defaultsettings.For details, see “To return the AccessPoint settings to the factory defaultsettings” (page 13).qdqd Ferrite coreTop view
12About the Access Point initial settingsThe Access Point is configured as follows at shipment.To return the Access Point settings to the factory default settings, see page13.NoteIn the table below, “–” indicates that no setting is made at the time of shipment.CommonHost Name homegateAdministrator Password –Guest Password –Time Server (NTP Server) –DNS Server –Operating Mode NAT Router ModeNETWORK 1Connection MethodObtain an IP address automaticallySpeed Auto-DetectDHCP Client ID –NETWORK 2IP Address 192.168.11.1Netmask 255.255.255.0DHCP IP Address Pool Size 16Speed Auto-DetectWIRELESSNetwork Name (SSID) ID printed on the ID label at therear of the productEncryption (WEP) DisabledWEP Key –Key Length 40 bits (5 characters)Frequency (Channel) 5.180 GHz (Channel 36)
13Getting startedTo return the Access Point settings to the factory default settingsTo return the Access Point settings to the factory default settings, holddown the factory default switch for approximately one second while thepower of the Access Point is ON. For information on the location of thefactory default switch position, see “Names of parts and functions” onpage 9.About the indicator displayWhen you press the factory default switch, the MESSAGE indicator flashesorange. If you continue to press this switch, the WIRELESS, NETWORK1, and NETWORK 2 indicators flash green, and the operation to return theAccess Point settings to the factory default settings begins. When theindicators stop flashing, the Access Point settings have been returned to thefactory default settings. For setting details, see page 12.NoteIf you perform this procedure, all previously set data will be lost.MAC addressYou can check the MAC address for the Access Point NETWORK 1connector on the Status Display screen. For details, see “Confirming thestatus of the Access Point” (page 21).
14Configuring the Access Point settingsTo configure the Access Point settings, use a computer that is connected tothe Access Point using the 5GHz Wireless LAN PC Card PCWA-C500 or acomputer that is connected to the Access Point NETWORK 2 connectorusing an Ethernet connection.Before configuring the Access Point settingsConnecting to the Access Point using a Wireless LAN PC Card•Insert the Wireless LAN PC Card into your computer, and install the PCcard driver.•Install the Wireless Panel software provided with the Wireless LAN PCCard.•Configure the wireless connection with the Access Point after you haveconfigured the computer communication settings on the Wireless Panel.z HintFor details, refer to the manuals provided with the Wireless LAN PC Card.Connecting the Access Point to the Internet❑To connect the Access Point to a DSL modem:In the DSL modem operating manual supplied by your ISP, check whetheryour ISP uses the PPPoE connection method or the router-type DSLmodem connection method. Depending on the connection method, performone of the following.For PPPoE connections:•Check the following using the data supplied by your ISP.(1) Account ID (Also referred to as the “User Account” or the “User ID”)(2) Account ID password(3) Service Name (Only when specified by your ISP)(4) Access Concentrator Name (Only when specified by your ISP)
15Setting and connections•Select Connect using DSL from NETWORK 1 Settings in Easy Setup(page 19) or from NAT Router Mode Settings in NETWORK 1 Settingsin Advanced Setup (page 20).For router-type DSL modem connections:Select Bridge Mode in Advanced Setup (page 20).❑To connect the Access Point to a cable modem:In the cable modem operating manuals supplied by your ISP, checkwhether your ISP uses the DHCP connection method (where the IP addressis automatically assigned to your computer) or the fixed IP address method(where you set the IP address for your computer manually). Depending onthe connection method, perform one of the following procedures.For DHCP connections (the IP address is automaticallyassigned to your computer):•Check the DHCP Client ID in the data supplied by your ISP. (Only whenspecified by your ISP)•Select Obtain an IP address automatically (DHCP) from NETWORK 1Settings in Easy Setup (page 19) or from NAT Router Mode Settings inNETWORK 1 Settings in Advanced Setup (page 20).For fixed IP address connections (you have to set the IPaddress for your computer manually):•Check the IP address assigned to your computer which is provided byyour ISP.•Select Use the following IP address from NETWORK 1 Settings in EasySetup (page 19) or from NAT Router Mode Settings in NETWORK 1Settings in Advanced Setup (page 20).❑When using an ISDN router:Select Bridge Mode in Advanced Setup (page 20).NoteDepending on your ISP, you may not be permitted to connect a router-type access point toa DSL or cable modem. For details, check the contract terms for your ISP.
16Displaying the Access Point setup pageTo configure Access Point settings, go to the Access Point setup page. Useone of the following three methods to display the Access Point setup page.•Display the Access Point setup page using the Wireless Connection EasySetup Wizard provided on the Wireless LAN PC Card. (page 17)NoteThis method can only be used with Windows Me or Windows 2000.•Display the Access Point setup page from the Wireless Panel. (page 17)•Display the Access Point setup page by entering the IP address in theweb browser. (page 18)NoteIf your web browser is configured to use a web proxy server, set the browser proxysettings so that the browser does not use a proxy server for the Access Point IP address.(The factory default setting for the Access Point IP address is 192.168.11.1.)z Hints•The Access Point setup page for configuring Access Point settings is saved in theAccess Point internal memory. To display the Access Point setup page, it is notnecessary to connect to the Internet.•When using an Ethernet connection to display the Access Point from your computer,see “Display the Access Point setup page by entering the IP address in the webbrowser. ” (page 18).
17Setting and connectionsNoteDepending on the firmware version of the Access Point you are using, the displayedscreen may differ from that shown above.Display the Access Point setup page using the WirelessConnection Easy Setup Wizard provided on the WirelessLAN PC CardNoteThis method can only be used with Windows Me or Windows 2000.1Connect the Access Point to the AC adapter.z HintThere is no power switch on the Access Point. Refer to the Quick Start Guide(separate sheet) when connecting the Access Point to the AC adapter.2Start the Wireless Connection Easy Setup Wizard.z HintTo Start the Wireless Connection Easy Setup Wizard, install the Wireless Panel andfollow the onscreen instructions. However, you can start the Wireless Network EasySetup Wizard any time you like.For details, refer to the Quick Start Guide.3Follow the onscreen instructions to configure thecommunication settings for your computer.After you have configured the communication settings for yourcomputer, follow the onscreen instructions to display the Access Pointsetup page.Display the Access Point setup page from the WirelessPanel1Connect the Access Point to the AC adapter.z HintThere is no power switch on the Access Point. Refer to the Quick Start Guide(separate sheet) when connecting the Access Point to the AC adapter.2Double-click the Wireless Panel icon (Received Signal Levelindicator) on the taskbar.The main screen for the Wireless Panel appears.3Click AP Settings.The web browser starts with the Access Point setup page displayed.
18Display the Access Point setup page by entering the IPaddress in the web browser.1Connect the Access Point to the AC adapter.z HintThere is no power switch on the Access Point. Refer to the Quick Start Guide(separate sheet) when connecting the Access Point to the AC adapter.2Start up your web browser.3Type “http://192.168.11.1/” in the URL entry field, then pressEnter.The Access Point setup page is displayed.z Hints•The IP address above is the factory default setting for the Access Point. If the IPaddress has been changed, contact your network administrator.•When using the NAT Router mode, the Access Point IP address is set to thedefault gateway for that network.•When using the Bridge mode, contact your network administrator for the AccessPoint IP address.About the Access Point passwordYou can set two types of Access Point passwords, administrator passwordand guest password. Neither of these passwords is set when the AccessPoint is shipped from the factory. Therefore, all users are able to configureAccess Point settings and display the status of the Access Point. If you wantto restrict the privileges of users, you can set a password as described onthe Easy Setup page or the various mode setting pages of Advanced Setup.Passwords and restrictions on executable functions are as follows.Password types and ability to use executable functionsFunction Administrator GuestStatus display Possible PossibleEasy Setup Possible Not possibleAdvanced Setup Possible Not possibleDisplay Indicator Possible Not possibleFirmware update Possible Not possible
19Setting and connectionsAdministrator passwordIf you set an administrator password, you will be requested to enter a username and password when you open the Access Point setup page.To open the Access Point setup page, type admin in the dialog box’s UserName text box, then type the password that you set in the Password textbox.Guest passwordIf you set a guest password, you will be requested to enter a user name andpassword when you open the Access Point Status page.Type guest in the User Name text box, then type the password that you setin the Password text box.Notes•If no administrator password is set, a guest password cannot be set.•If the administrator password is cancelled, the guest password is also cancelled.Configuring and changing settings for the Access PointThere are two types of Access Point settings:■Easy SetupFor those who are not familiar with networks, it is recommend that youuse Easy Setup. However, if the Access Point is connected to an ISDNrouter or router-type DSL modem, you must make settings in AdvancedSetup.•If you configure settings in Easy Setup, the Access Point operates inNAT router mode.•When making a PPPoE connection to your ISP using a DSL modem orwhen using a cable modem, you can normally configure all of therequired settings in Easy Setup.NoteIf you configure settings in Easy Setup after you have already configured settings inAdvanced Setup, the Advanced Setup settings are lost, and the settings are switched tothose in Easy Setup.
20■Advanced SetupHere, you can configure advanced settings for the Access Point. Further,you can select an operation mode for the Access Point from the followingtwo types:(1) NAT Router modeSimilar to Easy Setup, the Access Point operates in NAT routermode, but you can configure slightly more advanced settings.(2) Bridge modeThe Access Point operates as a network bridge. Select this modewhen using an ISDN router or router-type DSL modem.1Follow the steps for Displaying the Access Point setup page(page 16) to display the Access Point setup page.2Click Easy Setup or Advanced Setup.3If an administrator password has been set, you arerequested to enter a password. Type admin in the UserName text box, and enter the password, then click OK.The Access Point setup page appears.z HintThe administrator password is not set when the Access Point is shipped from thefactory. For details, see “About the Access Point password” (page 18).If the Access Point settings (Network name (SSID) or data encryption)have been changed, you must use the Wireless Panel to change thecommunication settings on your computer. For details, refer to the WirelessLAN PC Card Operating Instructions or the Wireless Panel Help.Confirming the firmware version for the Access PointYou can confirm the Access Point firmware version on the Access PointStatus page. For details, see “Confirming the status of the Access Point”(page 21).
21Setting and connectionsConfirming the status of the Access PointPerform the following steps to confirm the current status of the AccessPoint.1Follow the steps for Displaying the Access Point setup page(page 16) to open the Access Point setup page.2Click Status.3If a guest password has been set, you are requested toenter a password. Type guest in the User Name text box,and enter the password, then click OK.The status of the Access Point is displayed.z Hints•The guest password is not set when the Access Point is shipped from the factory.For details, see “About the Access Point password” (page 18).•Also, you can display the Access Point Status page using the administrator username “admin” and its password.
22ConnectingConnecting to a DSL modem, cable modem, or ISDN routerIf the Access Point is connected to a DSL modem, cable modem, or ISDNrouter, computers that are connected to the Access Point can connect to theInternet via the Access Point. Multiple computers can connect to theInternet via the Access Point simultaneously.POWERMESSAGEWIRELESSNETWORK 1NETWORK 2WARNINGIn the following cases, set the Access Point to Bridge mode before connectingto the Access Point. If you mix up the NETWORK 1 and NETWORK 2 connectorswhen the Access Point is in the NAT Router mode, problems may occur, such asnetwork anomalies or not being able to communicate with the Access Point.•When the Access Point is connected to an ISDN router•When the Access Point is connected to an existing LAN operating overa DHCP serverFor details on setting methods, see “Configuring the Access Point settings” (page 14).
23Setting and connections1Connect the Access Point’s NETWORK 1 connector to aDSL modem, cable modem, or ISDN router using anEthernet cable as shown in the illustration below. When theAccess Point is connected to an Ethernet LAN, connect theNETWORK 2 connector and the hub using an Ethernetcable.POWERMESSAGEWIRELESSNETWORK 1NETWORK 2Notes•Use a category 5 Ethernet cable when connecting to the Access Point.•Normally, an Ethernet straight-through cable is used when connecting a communicationdevice to the NETWORK 1 connector, but depending on the device you may need touse an Ethernet cable with crossover wiring. When connecting to the Access Point, usethe same type of cable that you would use to connect the communication device to yourcomputer. For details, refer to the operating instructions for the communication deviceyou are using.•When connecting the hub to the NETWORK 2 connector, use an Ethernet straight-through cable. When connecting the computer directly to the Access Point, use anEthernet crossover cable.z Hints•The cable supplied with the Access Point is an Ethernet straight-through cable.•For details on how to use the DSL modem, cable modem, or ISDN router, refer to therespective operating instructions.Connect the NETWORK 1connector to a DSLmodem, cable modem, orISDN router.Connect the NETWORK 2connector to the hub.
24Precautions when mounting the AccessPoint on a wallWhen mounting the Access Point on a wall, the screw size and spacing ofmounting holes is as follows. Note that no brackets are provided formounting the Access Point on a wall.Use screws or nails that meet the following requirements.Notes•Using two screws or other fasteners, ensure that the Access Point is securely set on thewall. When fastening the Access Point to a wall with screws, retighten them aftermounting the Access Point.•Select a location that will hold the weight of the Access Point when mounting it on thewall. If the location cannot hold the weight of the Access Point, the Access Point maydrop and cause an accident.•When mounting the Access Point on walls made of plasterboard or other fragilematerial, make sure that the material is strong enough to support the unit’s weight anduse special screw fasteners or other fixtures that are made for use with that material. Ifthe unit is fastened with ordinary screws, there is a danger that it may fall.•When mounting the Access Point on the wall, be careful not to drop the Access Point orthe tools used for doing the work. Dropping the unit or tools could result inunforeseeable accidents.Hanging the Access Point from screws set in a wall:Head diameter: 0.24 to 0.29 inches (6.0 to 7.5 mm)Body diameter: 0.14 to 0.15 inches (3.5 to 4.0 mm)Length: 1.2 inches (30 mm) or more2.82 inches (71.5 mm)
25Setting and connectionsFastening the Access Point to a wall with screws:Body diameter: 0.14 to 0.29 inches (3.5 to 7.5 mm)Length: 1.2 inches (30 mm) or more2.82 inches (71.5 mm)
26PrecautionsAC adapterUse ony the supplied AC adapter. OtherAC adapters may cause a failure in theAccess Point.SafetyDo not drop the Access Point. Carefulhandling will help prevent damage.InstallationDo not place the Access Point where itwill be exposed to the followingconditions:•Unstable surfaces.•High humidity or poor ventilation.•Excessive dust.•Direct sunlight or extreme heat.•Closed cars.•Magnetized locations (near magnets,speakers, or televisions).•Locations exposed to frequentvibration.•Locations where the transmission ofradio waves may be obstructed by metalplates or concrete wallsOperationExposure to cold-to-hot temperatureextremes or very damp environments maycause moisture to condense on internalparts. This may prevent the Access Pointfrom operating properly.If this should happen, unplug the ACadapter from the power outlet and let theAccess Point sit for two to three hours oruntil the moisture evaporates.CleaningClean the casing with a soft cloth, lightlymoistened with water or a mild detergentsolution. Do not use any type of abrasivepad, scouring powder or solvent such asalcohol or benzene. This may damage thefinish of the casing.
27Additional informationSpecificationsPowerAC 100 to 240 V, 50/60 Hz(The power cord plug is for use with AC 120 V.)Power consumptionApproximately 7 WMaximum external dimensionsApprox. 6.3 × 9.2 × 1.9 inches(Approx. 159 × 233 × 48 mm) (w/h/d)The stand is 3.6 inches (approx. 91 mm) indepth.Approx. 6.3 × 8.7 × 2.2 inches(Approx. 159 × 219 × 55 mm) (w/h/d)(With the stand folded)MassApprox. 42.4 oz(Approx. 1.2 kg )(Not including the AC adapter.)Maximum communication distanceApproximately 330 feet (100 m) in direct line ofsight with no obstacles(The maximum communication distance dependson the environment.)Recommended number of unitsconnected16 units or less (number of clients)Protocol supportTCP/IPStandardsIEEE802.11a/IEEE802.11 (wireless connection)IEEE802.3 (wired connection)Radio frequency5.15 to 5.35 GHzData transfer speed (logical value)Wireless connection: 54 Mbps max.Wired connection: 100 Mbps max.WEP (data encryption)64 bits128 bitsModulation methodOFDM (IEEE802.11a compliant)Operating temperature41°F to 95°F (5 to 35°C) (no condensation)Storage temperature-4°F to 140°F (-20 to 60°C) (no condensation)Supplied accessories•Operating Instructions•Quick Start Guide•AC adapter•Power cord•Ethernet cable (straight-through wiring)•Warranty card•Other printed materialsDesign and specifications are subject to changewithout notice.
28Getting helpThis section describes how to get help and supportfrom Sony, as well as troubleshooting tips for yourWireless LAN Access Point.About Sony’s Support OptionsSony provides several support options for yourWireless LAN Access Point.❒This Operating Instructionsexplains how to use your Wireless LANAccess Point.❒Quick Start Guide explains how toinstall the Wireless LAN Access Point.❒Access Point Online Help explainshow to configure the Access Point.❒The Sony Wireless LAN AccessPoint support Web sitehttp://www.sony.com/wirelesslansupport/ provides thelatest information on your WirelessLAN Access Point.❒The Sony e-mail support serviceanswers your questions by electronicmail. Just send your question in an e-mail message and a customer servicerepresentative will reply. To send aquestion to Sony e-mail support, fill outthe e-mail form athttp://www.sony.com/wirelesslansupport/❒The Sony fax-back service providesyou with answers to commonly askedquestions. You can use this automatedservice to request a list of availabletopics then select the topics you want toreceive. To contact the Sony fax-backservice, call1-877-760-7669.❒The Sony Customer InformationServices Center offers informationabout your Access Point, Wireless LANPC Card, and other Sony products thatwork with your computer. To contactthe Sony Customer InformationServices Center, call 1-877-760-7669.Open 24 hours/day, 7 days/week.
29Additional informationGlossaryChannel numberThe frequency used for wirelesscommunications. Wirelesscommunications are available only amongclient computers and Access Points thatuse the same channel.ClientA computer connected to a LAN (LocalArea Network). Also may be called aclient computer.DHCP (Dynamic HostConfiguration Protocol)DHCP lets network administratorscentrally manage and automateassignment of client computer IPaddresses.DNS (Domain Name System)A system that translates host names intoIP addresses.Networks that use the TCP/IP protocol,such as the Internet, use a set of numberslike 192.168.0.1 (IP address) to identify acomputer. However, since the IP addressis hard to memorize, DNS was developedto allow a name like “www.sony.com” toidentify a computer for convenience. DNSservers manage these translations fromhost names into IP addresses.LAN (Local Area Network)A network which is accessible only to itsmembers, unlike the Internet which isopen to an unlimited number of people. ALAN may be built for different purposes.For example, you can build an office LANthat is accessible only to members of thesame department or a home LAN that isaccessible only to family members.PPPoE (PPP over Ethernet)PPPoE is a software protocol that uses aDSL modem to access the Internet.With PPPoE, the client does not set astatic IP address. Instead, an IP address isassigned dynamically whenever the clientaccesses the Internet.ProtocolThe formal specifications that define theprocedures for computers to follow whentransmitting and receiving data.TCP/IP (Transmission ControlProtocol/Internet Protocol)TCP/IP is the network communicationsprotocol that is used to communicate overthe Internet. TCP is a connection-orientedprotocol for establishing reliable,sequenced data transfer. TCP ensures thatdata reaches its destination.IP assembles and addresses data packetsfor transmission to their networkdestinations.
30WAN (Wide Area Network)A network that interconnects remoteLANs through the Internet or telephonelines.WEPIEEE802.11-compliant security system.Using the WEP key as the password, onlyclient computers and Access Points thathave the same ID and password may logon to the same wireless LAN for filesharing.
31Additional informationTroubleshootingProblems related to the Access Point:Read the Troubleshooting section of this guide before calling SonyCustomer Information Services. If you still cannot resolve the problemsafter referring to these sources, call Sony Customer Information Services.Symptom Cause/RemedyThe Access Point isnot operating properlyor does not operate atall.The NETWORK 1 orNETWORK 2indicator is not lit.None of the indicatorsexcept the POWERindicator are lit.cThe Access Point is not supplied with power.Connect the Access Point to a power outlet with thesupplied AC adapter.cThere is an obstacle between the Access Point and thecomputer containing the Wireless LAN PC Card, or theyare too far apart from each other.cRemove the obstacle between them. Or place the AccessPoint and the computer containing the Wireless LAN PCCard closer together. (The maximum communicationdistance depends on the environment.)cThe cables are not properly connected.Check that you have connected the correct cables.cThe indicator display setting is turned OFF.Turn the power off, then turn it back on again. Or followthe steps for displaying the Access Point setup page (page16), open the Access Point homepage, and change theindicator display using the "Switch" button in DisplayStatus.
Printed in Japan❒The Sony e-mail support service answers your questionsby electronic mail. Just send your question in an e-mail messageand a customer service representative will reply. To send aquestion to Sony e-mail support, fill out the e-mail form athttp://www.sony.com/wirelesslansupport/❒The Sony fax-back service provides you with answers tocommonly asked questions. You can use this automated serviceto request a list of available topics and then select the topics youwant to receive. To contact the Sony fax-back service, call1-877-760-7669.❒The Sony Customer Information Services Center offersinformation about your Access Point, Wireless LAN PC Card,and other Sony products that work with your computer. Tocontact the Sony Customer Information Services Center, call1-877-760-7669.Open 24 hours/day, 7 days/week.

Navigation menu