Sony Group ZTXM01 DIGITAL WIRELESS MICROPHONE User Manual DWZ M50 DWZ B30GB

Sony Corporation DIGITAL WIRELESS MICROPHONE DWZ M50 DWZ B30GB

Short Term Confidentiality_Users Manual

E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB01COV.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (2)4-445-504-12 (2)© 2012 Sony CorporationDigital Wireless PackageOperating InstructionsBefore operating the unit, please read this manual thoroughly and retain it for future reference.DWZ-M50DWZ-B30GBThe supplied CD-ROM includes the Operating Instructions (English, French, German, Italian, and Spanish versions) in PDF format.For more details, see “Using the CD-ROM manual” on page 19.00DWZ.book  Page 1  Friday, August 31, 2012  11:50 AM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB02REG.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)2For the ZTX-M01/B01 TransmittersOwner’s RecordThe model and serial numbers are located at the rear or on the bottom of the unit. Record the model and serial numbers in the space provided below.Refer to these numbers whenever you call upon your Sony dealer regarding this product.Model No. _____________________Serial No. ______________________WARNINGBatteries shall not be exposed to excessive heat such as sunshine, fire or the like.If the transmitter develops an abnormally high temperature, a burning odor or smoke during use, remove the battery holder and stop using the transmitter immediately.Take care not to burn your fingers when removing the battery holder as the batteries may be very hot at this time.AVERTISSEMENTN’exposez pas les batteries à une chaleur excessive, au soleil ou près d’un feu par exemple.Si l’émetteur dégage une température anormalement élevée, une odeur de brûlé ou de la fumée pendant son utilisation, enlevez le support de piles et arrêtez toute utilisation immédiatement.Attention à ne pas vous brûler les doigts lorsque vous retirez le support de piles car celles–ci peuvent être brûlantes.WARNUNGAkkus dürfen keinesfalls übermäßiger Wärmeeinwirkung ausgesetzt werden, wie z.B. Sonneneinstrahlung, Feuer o. ä.Wenn der Sender eine abnorm hohe Temperatur, einen Geruch nach Verbranntem oder Rauch entwickelt, entnehmen Sie den Batterie-Halter und stoppen Sie sofort den Betrieb des Senders.Achten Sie bei der Entnahme des Batterie-Halters darauf, sich nicht die Finger zu verbrennen, denn die Batterien könnten sehr heiß zu diesem Zeitpunkt sein.For the customers in the U.S.A.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.If you have any questions about this product, you may call ;00DWZ.book  Page 2  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (2)3Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted.Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate this device.This device complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This device has very low levels of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR).This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.For the customers in CanadaThis Class B digital apparatus complies with Canadian ICES-003.This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR).Pour les clients au CanadaCet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.La mention « IC: » devant le numéro de certification/homologation signifie uniquement que les spécifications techniques d’Industrie Canada sont remplies.Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation du débit d’absorption spécifique (DAS).Declaration of ConformityTrade Name : SONYModel : ZTX-M01/B01Responsible party : Sony Electronics Inc.Address : 16530 Via Esprillo, San Diego, CA 92127 U.S.A.Telephone Number : 858-942-2230This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.00DWZ.book  Page 3  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-12 (2)4For the customers in EuropeHereby, Sony Corporation, declares that this ZTX-M01/B01 is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC. For details, please access the following URL: http://www.compliance.sony.de/Pour les clients en EuropePar la présente Sony Corporation déclare que l’appareil ZTX-M01/B01 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Pour toute information complémentaire, veuillez consulter l’URL suivante:http://www.compliance.sony.de/Für Kunden in EuropaHiermit erklärt Sony Corporation, dass sich das Gerät ZTX-M01/B01 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.Weitere Informationen erhältlich unter:http://www.compliance.sony.de/Per i clienti in EuropaCon la presente Sony Corporation dichiara che questo ZTX-M01/B01 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Per ulteriori dettagli, si prega di consultare il seguente URL:http://www.compliance.sony.de/Para los clientes de EuropaPor medio de la presente Sony Corporation declara que el ZTX-M01/B01 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Para mayor información, por favor consulte el siguiente URL:http://www.compliance.sony.de/Voor de klanten in EuropaHierbij verklaart Sony Corporation dat het toestel ZTX-M01/B01 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Nadere informatie kunt u vinden op:http://www.compliance.sony.de/För kunder i EuropaHärmed intygar Sony Corporation att denna ZTX-M01/B01 står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.För ytterligare information gå in på följande hemsida: http://www.compliance.sony.de/Para clientes na EuropaSony Corporation declara que este ZTX-M01/B01 está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Para mais informacoes, por favor consulte a seguinte URL: http://www.compliance.sony.de/Til europæiske kunderUndertegnede Sony Corporation erklærer herved, at følgende udstyr ZTX-M01/B01 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.For yderligere information gå ind på følgende hjemmeside: http://www.compliance.sony.de/Asiakkaille EuroopassaSony Corporation vakuuttaa täten että ZTX-M01/B01 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Halutessasi lisätietoja, käy osoitteessa:http://www.compliance.sony.de/For kunder i EuropaSony Corporation erklærer herved at utstyret ZTX-M01/B01 er i samsvar med de 00DWZ.book  Page 4  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (2)5grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF. For flere detaljer, vennligst se: http://www.compliance.sony.de/Για τους πελάτες που διαμένουν σε χώρες της EυρώπηςΜε την παρούσα η Sony Corporation δηλώνει τι ZTX-M01/B01 συμμορφώνεται προς της ουσιώδεις απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1999/5/ΕΚ.Για λεπτομέρειες παρακαλούμε πως ελένξετε την ακλουθη σελίδα του διαδικτύου:http://www.compliance.sony.de/Pro zákazníky v EvropěSony Corporation tímto prohlašuje, že tento ZTX-M01/B01 je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Podrobnosti lze získat na následující URL:http://www.compliance.sony.de/Klientidele EuroopasSony Corporation kinnitab käesolevaga seadme ZTX-M01/B01 vastavust 1999/5/EÜ direktiivi põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.Üksikasjalikum info: http://www.compliance.sony.de/.Európai ügyfeleinknekAlulírott, Sony Corporation nyilatkozom, hogy a(z) ZTX-M01/B01 megfelel a vonatkozó alapvető követelményeknek és az 1999/5/EC irányelv egyéb előírásainak.További információkat a következő weboldalon találhat:http://www.compliance.sony.de/Dla klientów w EuropieNiniejszym Sony Corporation oświadcza, że ZTX-M01/B01 jest zgodne z zasadniczymi wymaganiami oraz innymi stosownymi postanowieniami Dyrektywy 1999/5/WE.Szczegółowe informacje znaleźć można pod następującym adresem URL:http://www.compliance.sony.de/Pentru clienţii din EuropaPrin prezenta, Sony Corporation declară că acest ZTX-M01/B01 respectă cerinţele esenţiale și este în conformitate cu prevederile Directivei 1995/5/EC.Pentru detalii, vă rugăm accesaţi următoarea adresă:http://www.compliance.sony.de/Pre zákazníkov v EurópeSony Corporation týmto vyhlasuje, že ZTX-M01/B01 spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.00DWZ.book  Page 5  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-12 (2)6Podrobnosti získate na nasledovnej webovej adrese:http://www.compliance.sony.de/Za stranke v EvropiSony Corporation izjavlja, da je ta ZTX-M01/B01 v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.Za podrobnosti vas naprošamo, če pogledate na URL:http://www.compliance.sony.de/For the customers in EuropeThe manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents. Pour les clients en EuropeLe fabricant de ce produit est Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japon.Le représentant autorisé pour EMC et la sécurité des produits est Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Allemagne. Pour toute question concernant le service ou la garantie, veuillez consulter les adresses indiquées dans les documents de service ou de garantie séparés. Für Kunden in EuropaDer Hersteller dieses Produkts ist Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.Der autorisierte Repräsentant für EMV und Produktsicherheit ist Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Deutschland. Bei jeglichen Angelegenheiten in Bezug auf Kundendienst oder Garantie wenden Sie sich bitte an die in den separaten Kundendienst- oder Garantiedokumenten aufgeführten Anschriften.Per i clienti in EuropaIl fabbricante di questo prodotto è la Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Giappone.La rappresentanza autorizzata per EMC e la sicurezza dei prodotti è la Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stoccarda, Germania. Per qualsiasi questione riguardante l’assistenza o la garanzia, si prega di rivolgersi agli indirizzi riportati nei documenti sull’assistenza o sulla garanzia a parte.Para los clientes de EuropaEl fabricante de este producto es Sony Corporation, con dirección en 1-7-1 Konan, Minato-ku, Tokio, 108-0075 Japón.El Representante autorizado para EMC y seguridad del producto es Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Alemania. Para asuntos relacionados con el servicio y la garantía, consulte las direcciones entregadas por separado para los documentos de servicio o garantía.Voor klanten in EuropaDe fabrikant van dit product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.De geautoriseerde vertegenwoordiger voor EMC en productveiligheid is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Duitsland. Raadpleeg de adressen in de afzonderlijke service- of garantiedocumenten voor alle kwesties met betrekking tot service en garantie.För kunder i EuropaTillverkaren av denna produkt är Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.Auktoriserad representant för EMC och produktsäkerhet är Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Tyskland. För ärenden gällande service eller garanti, se de adresser som angivits i separata service- eller garantidokument.00DWZ.book  Page 6  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (2)7Para clientes na EuropaO fabricante deste produto é a Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japão.O Representante Autorizado para o EMC e segurança de produtos é a Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Alemanha. Para quaisquer questões sobre serviço ou a garantia, consulte os endereços nos documentos de serviço ou garantia fornecidos à parte.Kunder i EuropaProducenten af dette produkt er Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.Den autoriserede repræsentant for EMC og produktsikkerhed er Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Tyskland. Når det gælder service eller garantispørgsmål, henvises til de adresser, som er angivet i særskilte service- eller garantidokumenter.Asiakkaille EuroopassaTämän tuotteen valmistaja on Sony Corporation, 1-7-1 Konan, Minato-ku, Tokio, 108-0075 Japani.Valtuutettu sähkömagneettista yhteensopivuutta ja tuotteen turvallisuutta edustava taho on Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Saksa. Ottakaa yhteyttä huolto- ja takuuasioissa erillisissä huolto- tai takuuasiakirjoissa annettuihin osoitteisiin.For kunder i EuropaProdusenten av dette produktet er Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan. Den autoriserte representanten for EMC og produktsikkerhet er Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Tyskland. For all service eller garantisaker vennligs henvis til adressen som er oppgitt i de separate service eller garantidokumentene.Για τους πελάτες στην ΕυρώπηΟ κατασκευαστής αυτού του προϊντος είναι η Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.Ο εξουσιοδοτημένος αντιπρσωπος για EMC και την ασφάλεια προϊντος είναι η Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. Για οποιαδήποτε θέματα συντήρησης ή εγγύησης, παρακαλείστε να ανατρέξετε στις διευθύνσεις που δίνονται σε ξεχωριστά έγγραφα που αφορούν την συντήρηση ή την εγγύηση.За клиентите в ЕвропаПроизводителят на това изделие е Sony Corporation, 1-7-1 Konan, Minatoku, Токио, 108-0075 Япония.Оторизираният представител за електромагнитна съвместимост и безопасност на изделията е Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Щутгарт, Германия. За сервиз и проблеми с гаранцията се обръщайте към адресите, които са ви дадени в отделните сервизни книжни и гаранционни карти.Pentru clienţii din EuropaProducătorul acestui produs este Sony Corporation, 1-7-1 Konan, Minato-ku, Tokio, 108-0075 Japonia.Reprezentantul autorizat pentru EMC și siguranţa produsului este Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germania. Pentru orice probleme legate de service sau garanţie, vă rugăm să consultaţi adresele afișate în documentele separate pentru service sau garanţie.00DWZ.book  Page 7  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-12 (2)8Klientidele EuroopasSelle seadme tootja on Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.EMC ja toodete ohutuse volitatud esindaja on Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. Hoolduse või garantiiga seonduvates küsimustes vt aadresse eraldiseisvatest hooldus- või garantiidokumentidest.Európai ügyfeleinknekE termék gyártója a Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.EMC és termékbiztonság tekintetében a következő szervezet illetékes: Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. Szerviz és garancia ügyekben forduljon a külön szervizvagy jótállási füzetben feltüntetett szervezet(ek)hez.Europos klientamsŠio produkto gamintojas yra Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.EMC ir produkto saugos įgaliotasis atstovas yra Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. Dėl techninio aptarnavimo arba garantijos kreipkitės adresais, nurodytais atskiruose techninio aptarnavimo ir garantijos dokumentuose.Dla klientów w EuropieProducentem tego produktu jest Sony Corporation, 1-7-1 Konan, Minato-ku, Tokio, 108-0075 Japonia.Autoryzowanym przedstawicielem producenta w Europie w zakresie kompatybilności elektromagnetycznej i bezpieczeństwa produktu jest Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Niemcy. W sprawach serwisowych i gwarancyjnych należy kontaktować się z podmiotami, których adresy podano w osobnych dokumentach gwarancyjnych lub serwisowych.00DWZ.book  Page 8  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (2)9Za kupce v EvropiIzdelovalec tega izdelka je družba Sony Corporation, 1-7-1 Konan, Minato-ku, Tokio, 108-0075 Japonska.Pooblaščeni zastopnik za EMC in varnost izdelkov je družba Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Nemčija. V zvezi s servisiranjem in uveljavljanjem garancije se obrnite na naslove, ki so navedeni v ločeni servisni ali garancijski dokumentaciji.For the ZRX-HR50/C30 ReceiversOwner’s RecordThe model and serial numbers are located at the rear or on the bottom of the unit. Record the model and serial numbers in the space provided below.Refer to these numbers whenever you call upon your Sony dealer regarding this product.Model No. _____________________Serial No. _____________________IMPORTANTThe nameplate is located on the bottom.IMPORTANTLa plaque signalétique se situe sous l’appareil.WICHTIGDas Namensschild befindet sich auf der Unterseite des Gerätes.WARNINGExcessive sound pressure from earphones and headphones can cause hearing loss.In order to use this product safely, avoid prolonged listening at excessive sound pressure levels.Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.If the receiver develops an abnormally high temperature, a burning odor or smoke during use, remove the battery holder and stop using the receiver immediately.Take care not to burn your fingers when removing the battery holder as the batteries may be very hot at this time.AVERTISSEMENTUne pression acoustique excessive en provenance des écouteurs ou du casque peut provoquer une baisse de l’acuité auditive.Pour utiliser ce produit en toute sécurité, évitez l’écoute prolongée à des pressions sonores excessives.N’exposez pas les batteries à une chaleur excessive, au soleil ou près d’un feu par exemple.Si le récepteur dégage une température anormalement élevée, une odeur de brûlé ou de la fumée pendant son utilisation, enlevez le support de piles et arrêtez toute utilisation immédiatement.Attention à ne pas vous brûler les doigts lorsque vous retirez le support de piles car celles–ci peuvent être brûlantes.WARNUNGZu hoher Schalldruck von Ohrhörern und Kopfhörern kann Gehörschäden verursachen.Um dieses Produkt sicher zu verwenden, vermeiden Sie längeres Hören bei sehr hohen Schalldruckpegeln.00DWZ.book  Page 9  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-12 (2)10Akkus dürfen keinesfalls übermäßiger Wärmeeinwirkung ausgesetzt werden, wie z.B. Sonneneinstrahlung, Feuer o. ä.Wenn der Empfänger eine abnorm hohe Temperatur, einen Geruch nach Verbranntem oder Rauch entwickelt, entnehmen Sie den Batterie-Halter und stoppen Sie sofort den Betrieb des Empfängers.Achten Sie bei der Entnahme des Batterie-Halters darauf, sich nicht die Finger zu verbrennen, denn die Batterien könnten sehr heiß zu diesem Zeitpunkt sein.About the supplied AC adapterA propos de l’adaptateur CA fourniInformationen zum mitgelieferten NetzteilImportant Safety Instructions• Read these instructions.• Keep these instructions.• Heed all warnings.• Follow all instructions.• Do not use this apparatus near water.• Clean only with dry cloth.• Do not block any ventilation openings.Install in accordance with the manufacturer’s instructions.• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.• Only use attachments/accessories specified by the manufacturer.• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. • Unplug this apparatus during lightning storms or when unused for long periods of time.• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.WARNING00DWZ.book  Page 10  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (2)11Afin de réduire les risques d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité.Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié.Lors de l’installation de l’appareil, incorporer un dispositif de coupure dans le câblage fixe ou brancher la fiche d’alimentation dans une prise murale facilement accessible proche de l’appareil. En cas de problème lors du fonctionnement de l’appareil, enclencher le dispositif de coupure d’alimentation ou débrancher la fiche d’alimentation.Um die Gefahr von Bränden oder elektrischen Schlägen zu verringern, darf dieses Gerät nicht Regen oder Feuchtigkeit ausgesetzt werden.Um einen elektrischen Schlag zu vermeiden, darf das Gehäuse nicht geöffnet werden. Überlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal.Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, oder der Netzstecker muss mit einer in der Nähe des Geräts befindlichen, leicht zugänglichen Wandsteckdose verbunden werden. Wenn während des Betriebs eine Funktionsstörung auftritt, ist der Unterbrecher zu betätigen bzw. der Netzstecker abzuziehen, damit die Stromversorgung zum Gerät unterbrochen wird.CAUTIONThe apparatus shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.ATTENTIONEviter d’exposer l’appareil à un égouttement ou à des éclaboussures. Ne placer aucun objet rempli de liquide, comme un vase, sur l’appareil.Cet appareil n’est pas déconnecté de la source d’alimentation secteur tant qu’il est raccordé à la prise murale, même si l’appareil lui-même a été mis hors tension.VORSICHTDas Gerät ist nicht tropf- und spritzwassergeschützt. Es dürfen keine mit Flüssigkeiten gefüllten Gegenstände, z. B. Vasen, darauf abgestellt werden.Solange das Netzkabel an eine Netzsteckdose angeschlossen ist, bleibt das Gerät auch im ausgeschalteten Zustand mit dem Strommetz verbunden.For the customers in the U.S.A.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause AVERTISSEMENTWARNUNG00DWZ.book  Page 11  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-12 (2)12harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.If you have any questions about this product, you may call ;Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/For the customers in CanadaThis Class B digital apparatus complies with Canadian ICES-003.Pour les clients au CanadaCet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.For the customers in EuropeHereby, Sony Corporation, declares that this ZRX-HR50/C30 is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC. For details, please access the following URL: http://www.compliance.sony.de/Pour les clients en EuropePar la présente Sony Corporation déclare que l’appareil ZRX-HR50/C30 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Pour toute information complémentaire, veuillez consulter l’URL suivante:http://www.compliance.sony.de/Declaration of ConformityTrade Name : SONYModel : ZRX-HR50/C30Responsible party : Sony Electronics Inc.Address : 16530 Via Esprillo, San Diego, CA 92127 U.S.A.Telephone Number : 858-942-2230This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.00DWZ.book  Page 12  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (2)13Für Kunden in EuropaHiermit erklärt Sony Corporation, dass sich das Gerät ZRX-HR50/C30 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.Weitere Informationen erhältlich unter:http://www.compliance.sony.de/Per i clienti in EuropaCon la presente Sony Corporation dichiara che questo ZRX-HR50/C30 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Per ulteriori dettagli, si prega di consultare il seguente URL:http://www.compliance.sony.de/Para los clientes de EuropaPor medio de la presente Sony Corporation declara que el ZRX-HR50/C30 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Para mayor información, por favor consulte el siguiente URL:http://www.compliance.sony.de/Voor de klanten in EuropaHierbij verklaart Sony Corporation dat het toestel ZRX-HR50/C30 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Nadere informatie kunt u vinden op:http://www.compliance.sony.de/För kunder i EuropaHärmed intygar Sony Corporation att denna ZRX-HR50/C30 står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.För ytterligare information gå in på följande hemsida: http://www.compliance.sony.de/Para clientes na EuropaSony Corporation declara que este ZRX-HR50/C30 está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Para mais informacoes, por favor consulte a seguinte URL: http://www.compliance.sony.de/Til europæiske kunderUndertegnede Sony Corporation erklærer herved, at følgende udstyr ZRX-HR50/C30 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.For yderligere information gå ind på følgende hjemmeside: http://www.compliance.sony.de/Asiakkaille EuroopassaSony Corporation vakuuttaa täten että ZRX-HR50/C30 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Halutessasi lisätietoja, käy osoitteessa:http://www.compliance.sony.de/For kunder i EuropaSony Corporation erklærer herved at utstyret ZRX-HR50/C30 er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF. For flere detaljer, vennligst se: http://www.compliance.sony.de/Για τους πελάτες που διαμένουν σε χώρες της EυρώπηςΜε την παρούσα η Sony Corporation δηλώνει τι ZRX-HR50/C30 συμμορφώνεται προς της ουσιώδεις απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1999/5/ΕΚ.Για λεπτομέρειες παρακαλούμε πως ελένξετε την ακλουθη σελίδα του διαδικτύου:http://www.compliance.sony.de/00DWZ.book  Page 13  Friday, August 31, 2012  11:49 AM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504122_GB\4445504122\4445504122DWZM50UC\01GB02REG.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-12 (2)14Pro zákazníky v EvropěSony Corporation tímto prohlašuje, že tento ZRX-HR50/C30 je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Podrobnosti lze získat na následující URL:http://www.compliance.sony.de/Klientidele EuroopasSony Corporation kinnitab käesolevaga seadme ZRX-HR50/C30 vastavust 1999/5/EÜ direktiivi põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.Üksikasjalikum info: http://www.compliance.sony.de/.Európai ügyfeleinknekAlulírott, Sony Corporation nyilatkozom, hogy a(z) ZRX-HR50/C30 megfelel a vonatkozó alapvető követelményeknek és az 1999/5/EC irányelv egyéb előírásainak.További információkat a következő weboldalon találhat:http://www.compliance.sony.de/Dla klientów w EuropieNiniejszym Sony Corporation oświadcza, że ZRX-HR50/C30 jest zgodne z zasadniczymi wymaganiami oraz innymi stosownymi postanowieniami Dyrektywy 1999/5/WE.Szczegółowe informacje znaleźć można pod następującym adresem URL:http://www.compliance.sony.de/Pentru clienţii din EuropaPrin prezenta, Sony Corporation declară că acest ZRX-HR50/C30 respectă cerinţele esenţiale și este în conformitate cu prevederile Directivei 1995/5/EC.Pentru detalii, vă rugăm accesaţi următoarea adresă:http://www.compliance.sony.de/Pre zákazníkov v EurópeSony Corporation týmto vyhlasuje, že ZRX-HR50/C30 spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Podrobnosti získate na nasledovnej webovej adrese:http://www.compliance.sony.de/Za stranke v EvropiSony Corporation izjavlja, da je ta ZRX-HR50/C30 v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.Za podrobnosti vas naprošamo, če pogledate na URL:http://www.compliance.sony.de/00DWZ.book  Page 14  Friday, August 31, 2012  11:49 AM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB03TOC.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)15Table of ContentsTable of ContentsPackage Contents ........................  16DWZ-M50 ............................. 16DWZ-B30GB ........................ 17Features ........................................ 18DWZ-M50 ............................. 18DWZ-B30GB ........................ 18Using the CD-ROM manual  ....... 19Parts Identification ...................... 20DWZ-M50 ............................. 20DWZ-B30GB ........................ 23Power Supply  ............................... 27Inserting Batteries .................. 27Attaching the Supplied Accessories ................................... 29Attaching the Supplied Accessories to the Handheld Microphone (ZTX-M01)  ....... 29Attaching the Supplied Accessories to the Half-Rack Receiver (ZRX-HR50)  .......... 29Attaching the Supplied Accessories to the Body-Pack Transmitter (ZTX-B01) ......... 30Attaching the Supplied Accessories to the Compact Receiver (ZRX-C30) ............. 30Receiver Settings  ......................... 31Half-Rack Receiver (ZRX-HR50) ......................... 31Compact Receiver (ZRX-C30) ............................ 33Transmitter Settings  ................... 35Configuring the Transmitting Channel Settings .................... 35Channel Display  .................... 35System Configuration Examples....................................... 37Configuration Examples for the DWZ-M50 ........................37Configuration Example for the DWZ-B30GB .........................38Troubleshooting ........................... 39Important Notes on Use ...............42Usage and Storage ..................42Cleaning .................................42Specifications ................................43DWZ-M50 ..............................43DWZ-B30GB .........................4400DWZ.book  Page 15  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)16 Package ContentsPackage ContentsThis manual contains information on the Sony DWZ-M50/B30GB Digital Wireless Packages. The contents of each package are as follows.DWZ-M50This set includes a handheld microphone (transmitter: ZTX-M01) and a half-rack receiver (receiver: ZRX-HR50).Handheld microphone (ZTX-M01) (1)Supplied accessoriesAntenna (2)Half-rack receiver (ZRX-HR50) (1)Mic holder (1) AC adapter (1)Operating Instructions (1)CD-ROM (1)Waranty card (1) (for UC model only)Waranty booklet (1) (for SYV model only)00DWZ.book  Page 16  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)17Package ContentsDWZ-B30GBThis set includes a body-pack (transmitter: ZTX-B01) and a compact receiver (receiver: ZRX-C30).Body-pack transmitter (ZTX-B01) (1)Supplied accessoriesBelt clip (1)Compact receiver (ZRX-C30) (1)Guitar cable (1) Cable clamp (1)CD-ROM (1)Waranty card (1) (for UC model only)Belt clip screw (1)AC adapter (1)Operating Instructions (1)Waranty booklet (1) (for SYV model only)00DWZ.book  Page 17  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)18 FeaturesFeaturesThe DWZ series is a digital wireless system that combines Sony’s consistently developed superior audio technology, highly reliable wireless technology, and state-of-the-art digital signal processing technology. Using an unlicensed 2.4 GHz band, the system provides wide-range functionality with simple, user-friendly operability.By providing a package that is optimized for specific usage environments, the system offers a wireless solution to users ranging from those inexperienced with wireless systems to seasoned professionals.Superb audio qualityBy transmitting audio signals via 24-bit high-quality linear PCM digital transmission, without signal compression, decompression, or similar processing, the system provides superb audio quality and high-bandwidth transmissions that approach that of wired microphones.High reliabilityBy allowing you to select from two RF modes based on your intended use and incorporating Sony’s unique data processing technology, the system provides highly-reliable wireless transmission in wireless LAN environments. The receiver is equipped with two antennas with the antenna with the best reception status selected automatically via space diversity, providing stable reception with minimized audio breakup and noise occurrences.DWZ-M50The DWZ-M50 is a package that includes a handheld microphone (transmitter: ZTX-M01) and a half-rack receiver (receiver: ZRX-HR50) and is ideal for use with vocals.ZTX-M01A microphone designed with a sturdy metal body.Equipped with a muting function and an attenuator adjustment function, the unit supports a wide range of audio input levels. In addition, the interchangeable microphone unit allows you to use the microphone in a variety of applications.* The microphone unit’s mounting area has a diameter of 31.3 mm and a pitch of 1.0 mm.ZRX-HR50A half-rack receiver equipped with large-screen high-resolution color LCD that combines high-functionality with simple operability.The Best Channel Selection and Clear Channel Scan functions allow quick and easy configuration of safe channels. In addition, the 5-band graphic equalizer allows wide-range audio-quality adjustment. You can also select whether the muting function applies to the UNBALANCED OUTPUT TUNER/AUX connector.Using the optional RMM-HRD1 Rack Mount Kit allows you to mount the unit on a rack.DWZ-B30GBThe DWZ-B30GB is a package that includes a body-pack transmitter (transmitter: ZTX-B01) and a compact receiver (receiver: ZRX-C30) and is ideal for use with electric guitars, electric acoustic guitars, electric bass guitars, etc.00DWZ.book  Page 18  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)19Using the CD-ROM manualZTX-B01A transmitter designed with a sturdy metal body.Equipped with a muting function, an instrument/mic input switching function, and an attenuator adjustment function, the unit supports a wide range of audio input levels. The supplied belt clip can be rotated in 90-degree increments, allowing you to adjust the direction in which the cables extend based on your environment.ZRX-C30A compact receiver equipped with an internal antenna that is capable of withstanding rough handling.Power can be supplied by the supplied 12 V AC adapter, by an external 9 V DC power supply, or by a square 9 V dry cell battery (6LR61). The unit supports power distributors, allowing you to reduce noise caused by battery operation. The cable tone generator also allows you to match the quality of wireless and wired audio. This reduces the amount of equalizer adjustment necessary on the amp side during wireless transmission. The muting function does not affect the TUNER OUT connector, allowing tuning without sound output.Using the CD-ROM manualThe manual can be read on a computer with Adobe Reader installed.You can download Adobe Reader free from the Adobe website.1Open the index.html file in the CD-ROM.2Select and click on the manual that you want to read.If you have lost or damaged the CD-ROM, you can purchase a new one from your Sony dealer or Sony service counter. Adobe and Adobe Reader are trademarks of Adobe Systems Incorporated in the United States and/or other countries.Note00DWZ.book  Page 19  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)20 Parts IdentificationParts IdentificationDWZ-M50Handheld microphone (transmitter: ZTX-M01)aMicrophone unitThe standard-equipped microphone unit can be interchanged with another interchangeable microphone unit with a diameter of 31.3 mm and a pitch of 1.0 mm.For details on attaching and removing the microphone unit, see “Replacing the microphone unit” (page 29).bBATT/MUTING (remaining battery / muting) indicatorLights when the unit is turned on.This indicates the remaining battery charge and the on/off status of the muting function.The remaining battery indication only appears when alkaline dry cell batteries are being used.cPOWER/MUTING buttonTurns the unit on or off. This button can also be used to enable or disable the muting function.dGripContains the control buttons, channel display, and battery compartment.Open the grip to configure channel settings and replace the batteries.For details on opening the grip, see “Inserting Batteries” (page 27).eAntenna coverContains the antenna.Do not squeeze the antenna cover. Doing so will weaken the signal that is transmitted, decreasing the transmission range.Top (when microphone unit is removed)Grip interiorIndicator StatusLit (green) GoodLit (red) Almost deadBlinking (orange) Muting function enabled (i.e., audio disabled)Function Button operationTurn power on Press the button for at least 1 secondTurn power off Press the button until indicator turns offEnable muting functionPress the buttonDisable muting functionCaution00DWZ.book  Page 20  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)21Parts IdentificationfATT (attenuator) switchSet the attenuation level based on the sound volume.The attenuator switch is located at the top of the unit when the microphone unit is removed.For details on attaching and removing the microphone unit, see “Replacing the microphone unit” (page 29).gChannel displayDisplays the transmission channel.The display disappears after about 10 seconds. You can display it again by pressing the channel selection button.For details on the channel display, see “Channel Display” (page 35).hChannel selection buttonAllows you to select the RF mode and the transmitting channel.For details on selecting the RF mode and transmitting channel, see “Configuring the Transmitting Channel Settings” (page 35).iButton lock switchLocks the POWER/MUTING button and the channel selection button. This prevents unintentional operations, such as accidentally turning the power off.LOCK: Locks the buttons to disable their operation.UNLOCK: Releases the lock to enable button operation.You cannot turn on the unit while this switch is set to the LOCK position, as even the power button is disabled. Set the switch to the UNLOCK position to perform operations.Half-rack receiver (receiver: ZRX-HR50)aPOWER buttonTurns the unit on or off.bPOWER indicatorLights when the unit is turned on.cDisplayDisplays setting configurations and other information.AReceiving channel indicatorDisplays the receiving channel.Attenuation level (dB)When to use0 Standard switch position6 Set to this position if a red bar occasionally appears in the audio level meter of the receiver.12 Set to this position if a red bar always appears in the audio level meter of the receiver.CautionFront00DWZ.book  Page 21  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)22 Parts IdentificationBRemaining transmitter battery indicatorDisplays the remaining battery charge of the transmitter.An approximate duration is displayed for the remaining usage time. This duration appears only when signals are being received.CAudio level meterDisplays the audio level.Set the audio level so that the yellow or red bar does not appear.DEqualizer statusDisplays the on/off status of the equalizer.EReceiving level indicatorDisplays the reception status of the radio signal.More bars indicate more stable reception.dESC (escape) buttonCancels operations, or returns to the main screen from the settings screen.eRotary encoderAllows you to change settings.For details on changing settings, see “Receiver Settings” (page 31).aANTENNA a/b connector (BNC type)Connect the supplied antenna here.bUNBALANCED OUTPUT TUNER/AUX (external audio output) connector (headphone jack)Connect monitoring equipment and similar peripheral devices here.The audio output from the UNBALANCED OUTPUT TUNER/AUX connector will continue, even if the muting function of the transmitter is enabled. You can enable or disable the audio from this connector via the settings in the receiver’s display.For details on settings, see “Configuring the transmitter muting function for the UNBALANCED OUTPUT TUNER/AUX connector” (page 33).For details on connections, see “System Configuration Examples” (page 37).cUNBALANCED OUTPUT MAIN (main audio output) connector (headphone jack)Connect a mixer or an amp here.For details on connections, see “System Configuration Examples” (page 37).dBALANCED OUTPUT connector (XLR type)Connect a mixer or similar device here.For details on connections, see “System Configuration Examples” (page 37).eMIC/LINE (audio output level) selectorSelects the audio output level of the BALANCED OUTPUT connector.MIC: Sets the audio output level to the mic level.LINE: Sets the audio output level to the line level.Do not set the selector to the LINE position while outputting audio to an audio mixer or similar device. Inputting audio at excessive levels may distort audio or damage the playback/recording device.RearCaution00DWZ.book  Page 22  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)23Parts IdentificationfCable clampSecures the cable of the supplied AC adapter.gDC IN 12V (power input) connectorConnect the supplied AC adapter here.DWZ-B30GBBody-pack transmitter (transmitter: ZTX-B01)aAntenna coverContains the antenna.Do not squeeze the antenna cover. Doing so will weaken the signal that is transmitted, decreasing the transmission range.bBATT (remaining battery) indicatorIndicates the remaining battery charge when the unit is turned on.The remaining battery indication only appears when alkaline dry cell batteries are being used.cButton lock switchLocks the POWER/MUTING button and the CHANNEL SELECT button. This prevents unintentional operations, such as accidentally turning the power off.LOCK: Locks the buttons to disable their operation.UNLOCK: Releases the lock to enable button operation.You cannot turn on the unit while this switch is set to the LOCK position, as even the power button is disabled. Set the switch to the UNLOCK position to perform operations.dAudio input connectorConnect a guitar or similar instrument here using the supplied guitar cable.eAUDIO/MUTING indicatorIndicates the input level of the audio signal and the status of the muting function.fINPUT switchSet this based on the connected equipment.INST: Set to this position when a guitar or similar instrument is connected.MIC: Set to this position when a microphone is connected.CautionIndicator StatusLit (green) GoodLit (red) Almost deadCautionIndicator StatusLit (green) Audio input presentLit (red) Excessive audio inputOff Audio input weak or nonexistentBlinking (orange) Muting function enabled (i.e., audio disabled)00DWZ.book  Page 23  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)24 Parts IdentificationDo not set the switch to the INST position while outputting audio to an audio mixer or similar device. Inputting audio at excessive levels may distort audio or damage the playback/recording device.For details on the setting, see “System Configuration Examples” (page 37).gATT (attenuator) switchSet the attenuation level based on the connected equipment.hBattery compartmentInsert two LR6 (size AA) batteries here.For details on how to insert batteries, see “Inserting Batteries” (page 27).iPOWER/MUTING buttonTurns the unit on or off. This button can also be used to enable or disable the muting function.jChannel displayDisplays the transmission channel.The display disappears after about 10 seconds. You can display it again by pressing the channel selection button.For details on the channel display, see “Channel Display” (page 35).kCHANNEL SELECT buttonAllows you to select the RF mode and the transmitting channel.For details on selecting the RF mode and transmitting channel, see “Configuring the Transmitting Channel Settings” (page 35).Compact receiver (receiver: ZRX-C30)CautionAttenuation level (dB)When to use0 Standard switch position10 Set to this position if the AUDIO/MUTING indicator on the receiver occasionally lights red.20 Set to this position if the AUDIO/MUTING indicator on the receiver is always lit red.Function Button operationTurn power on Press the button for at least 1 secondTurn power off Press the button until indicator turns offEnable muting functionPress the buttonDisable muting functionLeft/rearTop/front00DWZ.book  Page 24  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)25Parts IdentificationaPOWER indicatorLights when the unit is turned on. When a square 9 V dry cell battery (6LR61) is being used, this also indicates the remaining battery charge.bRF (radio frequency input) indicatorDisplays the reception status of the radio signal.cAUDIO indicatorIndicates the status of the audio signal.dTUNER OUT connector (TS phone type)Connect a tuning meter or similar device here.The audio output from the TUNER OUT connector will continue, even if the muting function of the transmitter is enabled.For details on connections, see “System Configuration Examples” (page 37).eMAIN OUT connector (TS phone type)Connect a guitar amp or bass amp here.For details on connections, see “System Configuration Examples” (page 37).fCABLE TONE (cable tone generator) switchTurn the knob to configure the cable tone generator.For details on the cable tone generator, see “Configuring the cable tone generator” (page 34).gCHANNEL (channel selection) switchTurn the knob to select the receiving channel.The receiving channel will be set to the channel of the RF mode that is selected with the RF MODE switch.For details on settings, see “Configuring the RF mode and receiving channel” (page 33).hRF MODE indicatorsThe indicator of the RF mode that is selected with the RF MODE switch lights.iRF MODE (RF mode selection) switchSelects the RF mode.For details on settings, see “Configuring the RF mode and receiving channel” (page 33).jBALANCED OUTPUT connector (XLR type)Connect a mixer or similar device here.For details on connections, see “System Configuration Examples” (page 37).kCable clamp attachment holeAttach the supplied cable clamp here.For details on attaching the cable clamp, see “Attaching the cable clamp” (page 30).Indicator StatusLit (green) GoodLit (red) Almost deadIndicator StatusLit (green) Reception goodLit (red) Reception poorOff No receptionIndicator StatusLit (green) Audio input presentLit (red) Excessive audio inputOff Audio input weak or nonexistentCaution00DWZ.book  Page 25  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)26 Parts IdentificationlDC IN 9V (power input) connectorUse this to connect to a commercially available 9 V DC power supply unit.mDC IN 12V (power input) connectorConnect the supplied AC adapter here.nPOWER switchTurns the unit on or off.oTX MUTING (transmitter muting) indicatorIndicates the status of the muting function for the transmitter.This blinks orange when the muting function is enabled.pTX BATT (remaining transmitter battery) indicatorIndicates the remaining battery charge of the transmitter.The remaining battery indication only appears when alkaline dry cell batteries are being used.aBattery compartmentInsert a square 9 V dry cell (6LR61) battery here.For details on how to insert batteries, see “Inserting Batteries” (page 27).Indicator StatusLit (green) GoodLit (red) Almost deadBottom00DWZ.book  Page 26  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)27Power SupplyPower SupplyThis section describes the power supply for each device.For details on how to insert batteries, see “Inserting Batteries” (page 27).Handheld microphone (ZTX-M01), body-pack transmitter (ZTX-B01)Power supplied by two LR6 (size AA) batteries.The following types of battery can be used.• Alkaline dry cell batteries• Rechargeable nickel-metal hydride batteries• Lithium batteriesHalf-rack receiver (ZRX-HR50)Power supplied by the supplied AC adapter.Compact receiver (ZRX-C30)Power can be supplied by the supplied AC adapter, by a commercially available 9 V DC power supply unit, or by a square 9 V dry cell battery (6LR61).Priority sequence for power suppliesWhen multiple power supplies are made available for use, they will be used in the following order of priority.A12 V power inputB9 V power inputCSquare 9 V dry cell battery (6LR61)Inserting BatteriesCAUTIONDanger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. When you dispose of the battery, you must obey the law in the relative area or country.ATTENTIONIl y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur.Lorsque vous mettez la batterie au rebut, vous devez respecter la législation en vigueur dans le pays ou la région où vous vous trouvez.VORSICHTExplosionsgefahr bei Verwendung falscher Batterien. Batterien nur durch den vom Hersteller empfohlenen oder einen gleichwertigen Typ ersetzen.Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. Replacing the batteries during operation will result in high noise. Be sure to turn off the unit before replacing the batteries.Handheld microphone (ZTX-M01)1Press and hold the POWER/MUTING button to turn off the unit.2Turn the grip in the direction of the arrow, and pull down the grip until the battery compartment is shown.Note00DWZ.book  Page 27  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)28 Power Supply3Insert two new LR6 (size AA) batteries while making sure the polarities are correct.4Close the grip and turn it in the reverse direction in the step 2 above.Body-pack transmitter (ZTX-B01)1Press and hold the POWER/MUTING button to turn off the unit.2Slide the battery-compartment catches inward (in the direction of the arrows b B) to take out the compartment.3Insert two new LR6 (size AA) batteries into the battery compartment while making sure the polarities are correct, and then reinsert the compartment into the unit.Compact receiver (ZRX-C30)1Set the POWER switch to the OFF position to turn off the unit.2Slide open the battery compartment cover at the bottom of the device.3Connect the new square 9 V dry cell (6LR61) battery to the unit’s battery snap while making sure the polarities are correct, and then insert the battery into the compartment.4Close the battery compartment.00DWZ.book  Page 28  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)29Attaching the Supplied AccessoriesAttaching the Supplied AccessoriesThis section describes how to attach the supplied accessories to each unit.Attaching the Supplied Accessories to the Handheld Microphone (ZTX-M01)Attaching the microphone holderReplacing the microphone unitTo remove the microphone unitTo attach the microphone unitTurn the microphone unit in the opposite direction from when you removed it, and make sure that the unit is securely attached to the microphone.Attaching the Supplied Accessories to the Half-Rack Receiver (ZRX-HR50)Attaching the antennaInsert the bottom part of the microphone into the holder.Turn the microphone unit in the direction of the arrow.Insert the supplied antenna into the ANTENNA a/b connector at the rear of the receiver and turn it.00DWZ.book  Page 29  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)30 Attaching the Supplied AccessoriesAttaching the Supplied Accessories to the Body-Pack Transmitter (ZTX-B01)Attaching the belt clipTo attach to a guitar strapDepending on the thickness and width of the strap, the belt clip may not attach securely.Attaching the Supplied Accessories to the Compact Receiver (ZRX-C30)Attaching the cable clampCautionAlign the mounting hole at the rear of the transmitter with the hole in the middle of the supplied belt clip, and secure the belt clip using the supplied belt clip screw.You can also rotate the belt clip 180 degrees or 90 degrees to the left or right before securing it.Slide the guitar strap into the belt clip on the unit completely, and make sure it is secure.Insert the cable clamp into the cable clamp attachment hole on the left side of the receiver.00DWZ.book  Page 30  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504121_GB\4445504121\4445504121DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (1)31Receiver SettingsReceiver SettingsHalf-Rack Receiver (ZRX-HR50)Use the rotary encoder and the ESC button to configure settings on the ZRX-HR50 half-rack receiver. Perform setting operations as follows.Confirm: Press the rotary encoder.Move cursor: Turn the rotary encoder.Cancel: Press the ESC button.Displaying the settings menuPress the rotary encoder to display the [Setup] screen in the display.To return to the main screen from the [Setup] screen, press the ESC button.Configuring the receiving channel settingsTwo RF modes (channel modes), wide band and narrow band, are available on the DWZ.Each RF mode consists of six channels. Select the appropriate channel according to your intended use.When using multiple channels (up to six), the two RF modes, wide band and narrow band, cannot be used simultaneously. Select only one RF mode during use.To select the RF mode1In the [Setup] screen, select [Advanced Settings].2Select [RF Mode Settings].The [RF Mode Settings] screen appears.3Select [Wide Band] or [Narrow Band].When the configuration is complete, the main screen appears again.RF modeTransmitting channel numberDescriptionWide band (WIDE)1/2/3/4/5/6 This mode reduces any interference to other wireless equipment.Narrow band (NARROW)a/b/c/d/e/f This mode uses the Clear Channel Scan function, making it useful for avoiding any interference from other wireless equipment.Caution00DWZ.book  Page 31  Saturday, August 25, 2012  6:24 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)32 Receiver SettingsTo select the channel1In the [Setup] screen, select [Channel Setup].The [Channel Setup] screen appears.2Specify the channel using one of the following methods.ASelect [Best Channel Selection]The channel with the least interference will be configured automatically.BSelect [Clear Channel Scan]The status of all the channels in the selected RF mode will be displayed, allowing you to select the channel you want to use.If there are no open channels, “No Clear Channel” appears.CSelect [Manual Setup]Configure the channel manually. Select the channel you want to use.This completes the configuration, and the main screen appears again.If you change the channel setting, be sure to change the channel setting on the transmitter to the same channel. If the receiver channel and transmitter channel are not identical, audio will not be output.Configuring the equalizer1In the [Setup] screen, select [Audio Setup].The [Audio Setup] screen appears.2Select [Equalizer].The [Equalizer] screen appears.3Select [ON] to enable the equalizer function, or [OFF] to disable it.If you select [ON], the equalizer settings screen appears.If you select [OFF], configuration is complete and the main screen appears again.4Select the frequency for which you want to adjust the level, and adjust the setting.Display StatusWhite font (underlined)Channel with low interference.White font Channel with relatively low interference.Gray font Channel with high interference, or channel that is being used by another device.“No Clear Channel”No usable channels available.Caution00DWZ.book  Page 32  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)33Receiver Settings5Select [Set].The setting value is saved.To cancel the setting, press the ESC button.Configuring the transmitter muting function for the UNBALANCED OUTPUT TUNER/AUX connectorYou can select whether the muting function of the transmitter will be applied to the audio output of the UNBALANCED OUTPUT TUNER/AUX (external audio output) connector.The audio output from the UNBALANCED OUTPUT TUNER/AUX connector will continue, even if the muting function of the transmitter is enabled. To disable the audio output from the UNBALANCED OUTPUT TUNER/AUX connector, enable the TX Muting function.1In the [Setup] screen, select [Audio Setup].The [Audio Setup] screen appears.2Select [AUX/Tuner Out Settings].The [AUX/Tuner Out Settings] screen appears.3Select whether to enable the muting function.TX Muting Valid: Enables the TX Muting function. The audio output from the connector is disabled when the muting function of the transmitter is enabled.TX Muting Invalid: Disables the TX Muting function. The audio out put from the connector will continue, regardless of whether the muting function of the transmitter is enabled or disabled.This completes the configuration, and the main screen appears again.Configuring the battery typeSpecify the type of battery that is being used in the transmitter so that the transmitter’s remaining battery charge can be displayed properly on this unit.1In the [Setup] screen, select [Advanced Settings].2Select [Battery Type].3Select the battery type.Alkaline: Alkaline dry cell batteries are being used in the transmitter.Ni-MH: Rechargeable nickel-metal hydride batteries are being used in the transmitter.Lithium: Lithium batteries are being used in the transmitter.This completes the configuration, and the main screen appears again.Compact Receiver (ZRX-C30)Configuring the RF mode and receiving channelTwo RF modes (channel modes), wide band and narrow band, are available on the DWZ.Each RF mode consists of six channels. Select the appropriate channel according to your intended use.Caution00DWZ.book  Page 33  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504121_GB\4445504121\4445504121DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-12 (1)34 Receiver SettingsWhen using multiple channels (up to six), the two RF modes, wide band and narrow band, cannot be used simultaneously. Select only one RF mode during use.1Set the RF MODE (RF mode selection) switch to WIDE or NARROW.2Turn the CHANNEL (channel selection) switch to set the receiving channel.If you change the channel setting, be sure to change the channel setting on the transmitter to the same channel. If the receiver channel and transmitter channel are not identical, audio will not be output.Configuring the cable tone generatorThe cable tone generator is a function that modifies sound properties to simulate the quality of a wired cable connection.You can simulate the sound quality of a cable that is 1 m to 25 m in length by setting the CABLE TONE switch to the corresponding number (m).Supposed cable length (m): OFF/1/3/5/8/12/18/25RF modeTransmitting channel numberDescriptionWide band (WIDE)1/2/3/4/5/6 This mode reduces any interference to other wireless equipment.Narrow band (NARROW)a/b/c/d/e/f This mode uses the Clear Channel Scan function, making it useful for avoiding any interference from other wireless equipment.CautionCaution00DWZ.book  Page 34  Saturday, August 25, 2012  6:24 PM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504121_GB\4445504121\4445504121DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (1)35Transmitter SettingsTransmitter SettingsConfiguring the Transmitting Channel SettingsTwo RF modes (channel modes), wide band and narrow band, are available on the DWZ.Each RF mode consists of six channels. Select the appropriate channel according to your intended use.When using multiple channels (up to six), the two RF modes, wide band and narrow band, cannot be used simultaneously. Select only one RF mode during use.Selecting the RF mode1Press and hold the POWER/MUTING button to turn off the unit.2Press and hold the POWER/MUTING button (about 1 second) while holding down the channel selection button.“0” blinks in the channel display.3Press the channel selection button to select “1” or “a.”4Press the POWER/MUTING button.Selecting the channel1Press and hold the channel selection button while the unit is turned on.The channel display blinks.2Press the channel selection button to select the channel.3Press and hold the channel selection button to apply the channel selection.If you change the channel setting on the transmitter, be sure to change the channel setting on the receiver to the same channel. If the receiver channel and transmitter channel are not identical, audio will not be output.Channel DisplayEach channel will appear as follows in the transmitter’s channel display.RF modeTransmitting channel numberDescriptionWide band (WIDE)1/2/3/4/5/6 This mode reduces any interference to other wireless equipment.Narrow band (NARROW)a/b/c/d/e/f This mode uses the Clear Channel Scan function, making it useful for avoiding any interference from other wireless equipment.CautionCaution00DWZ.book  Page 35  Saturday, August 25, 2012  6:24 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)36 Transmitter SettingsRF mode Channel numberWide band (WIDE)1 2 3 4 5 6 Narrow band (NARROW)a b c d e f 00DWZ.book  Page 36  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)37System Configuration ExamplesSystem Configuration Examples Production of the peripheral and relating devices may have been discontinued. Upon selecting the devices to be used with this product, consult your nearest Sony representative or the dealer from whom you purchased the product.Configuration Examples for the DWZ-M50NoteHandheld microphone (ZTX-M01)Half-rack receiver (ZRX-HR50)Mixer Power amp SpeakerDC IN 12V (power input) connectorAntenna (supplied)ANTENNA b connectorUNBALANCED OUTPUT MAIN (main audio output) connectorMixer, recorder, etc.ANTENNA a connectorAntenna (supplied)BALANCED OUTPUT connectorAC adapter (supplied)00DWZ.book  Page 37  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)38 System Configuration ExamplesConfiguration Example for the DWZ-B30GBINPUT switch: INSTAC adapter (supplied)TUNER OUT connectorEffector Guitar ampMixer, recorder, etc.DC IN 12V (power input) connectorMAIN OUT connectorBALANCED OUTPUT connectorGuitar tunerBody-pack transmitter (ZTX-B01)Compact receiver (ZRX-C30)Guitar or bass00DWZ.book  Page 38  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)39TroubleshootingTroubleshootingCheck the following if problems occur.Should any problem persist, consult your Sony dealer.Symptom Meanings RemedyThe unit does not turn on.The polarity orientation of the batteries in the battery compartment is incorrect.Insert the batteries with the correct polarity orientation.The batteries are exhausted. Replace the batteries with new ones.Button operations are locked. Set the button lock switch to UNLOCK.The batteries drain quickly.The batteries are exhausted. Replace the batteries with new ones.Manganese batteries are being used. Use alkaline batteries. The battery life of a manganese battery is less than half that of an alkaline battery.The unit is being used under cold conditions.The batteries drain quickly under cold conditions.There is no sound. The RF mode or channel setting on the transmitter is different from that on the receiver.Use the same RF mode and channel setting on both the transmitter and the receiver.The sound is weak. The attenuation level on the transmitter is too high.The input level is low. Set the attenuation level on the transmitter to the appropriate level.The output level of the receiver does not match the input level setting of the connected device.Set the MIC/LINE selector according to the input level of the connected device (ZRX-HR50).00DWZ.book  Page 39  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)40 TroubleshootingThe sound is distorted.The attenuation level of the transmitter is too low.The audio input level is too high. Set the attenuation level on the transmitter to a level where sound is not distorted.The transmitter is set to MIC input.The audio input level is too high. Specify INST input.The output level of the receiver does not match the input level setting of the connected device.Set the MIC/LINE selector according to the input level of the connected device (ZRX-HR50).Noise occurs. The transmitter and receiver are far away from each other.Shorten the distance between the transmitter and receiver until audio breakup does not occur.Signal interference from other devices is occurring.Change the selected channel, or move the devices that are causing interference away from the unit.The service area (i.e., operating range) is small.Two or more transmitters are set to the same channel.Do not use the same channel for more than one transmitter.The antenna is not attached to the receiver.Attach the supplied antenna.Wide band and narrow band are being used simultaneously.When using multiple channels simultaneously, use channels from a single RF mode, either wide mode or narrow mode.The audio quality is abnormal.The cable tone generator setting is incorrect.Set the cable tone generator to a suitable setting (ZRX-C30).The equalizer setting is incorrect.Set the equalizer to a suitable setting (ZRX-HR50).The unit does not turn off when the POWER switch is pressed.Button operations are locked. Set the button lock switch to UNLOCK.The RF mode is being configured.The unit cannot be turned off while RF mode configuration is in progress (ZTX-M01/B01).Channels cannot be changed.Button operations are locked. Set the button lock switch to UNLOCK.The settings menu is not open.Follow the instructions in “Displaying the settings menu” and “Configuring the receiving channel settings” (page 31) to configure settings (ZRX-HR50).Symptom Meanings Remedy00DWZ.book  Page 40  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)41TroubleshootingThe RF indicator on the receiver lights even when the transmitter is off.Interference is being received.Set the receiver to a channel for which the RF indicator does not light, and then set the transmitter to the same channel.Symptom Meanings Remedy00DWZ.book  Page 41  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)42 Important Notes on UseImportant Notes on UseThe operating range of the 2.4 GHz band used by the units may be reduced and noise may occur due to interference from the operating environment or from other wireless stations. In such cases, moving the units away from other wireless stations or changing the channel may resolve the problem.• If other wireless stations are being used nearby, distance the units from the stations as much as possible, or change the channel or RF mode being used.• If this does not resolve the problem, try turning off the other wireless stations (i.e., stopping their radio signals) one by one.To prevent audio noise caused by interference from other transmitters or by excessive RF inputs, maintain a distance of at least 30 cm between the transmitter and the receiver.Usage and Storage• Operating the DWZ series components near electrical equipment (motors, transformers, or dimmers) may cause it to be affected by electromagnetic induction. Keep the DWZ series components as far from such equipment as possible.• The presence of the lighting equipment may produce electrical interference over the entire frequency range. Position the DWZ series components so that interference is minimized.CleaningClean the surface and the connectors of the DWZ series components with a dry, soft cloth. Never use thinner, benzene, alcohol or any other chemicals, since these may mar the finish.CautionTo prevent electromagnetic interference from portable communication devicesThe use of portable telephones and other communication devices near the DWZ series components may result in malfunction and interference with audio signals. It is recommended that portable communication devices near the DWZ series components be turned off.00DWZ.book  Page 42  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504121_GB\4445504121\4445504121DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-12 (1)43SpecificationsSpecificationsDesign and specifications are subject to change without notice.DWZ-M50Carrier frequencies2402.0 MHz to 2478.5 MHzOccupied RF bandwidth2.5 MHzType of emissionF1D and F1EModulation methodGFSKOperating temperature0 °C to 50 °C (32 °F to 122 °F)Storage temperature–20 °C to +60 °C (–4 °F to +130 °F)Handheld microphone (ZTX-M01)RF output level10 mW (e.i.r.p.)Antennaλ/4 monopole antennaMicrophone typeDynamic: unidirectionalFrequency responseTransmission: 10 Hz to 22 kHzMicrophone unit: 70 Hz to 16 kHzMaximum input level142 dBSPL (when attenuator level is 12 dB)Dynamic range102 dB (A-weighted)Power requirements3.0 V DC (two LR6 (size AA) alkaline dry cell batteries)Battery lifeApprox. 10 hours of continuous use (25 °C (77 °F) ambient temperature, Sony LR6 (size AA) alkaline dry cell batteries)Dimensionsφ 48 × 258 mm (1 15/16 × 10 1/4 inches) (diameter/length)Mass Approx. 305 g (11 oz.) (including batteries)Half-rack receiver (ZRX-HR50)Reception typeSpace diversityNoteAlways verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.25848Unit: mm00DWZ.book  Page 43  Saturday, August 25, 2012  6:23 PM
E:\#works_2\120800937_DWZ-M50_B30GB\120800937_4445504121_GB\4445504121\4445504121DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-12 (1)44 SpecificationsANTENNA a/b connectorBNC-R, 50 ΩFrequency response10 Hz to 22 kHzMaximum output levelBalanced OutputMIC: –22 dBuLINE: +24 dBuUnbalanced Output: +8 dBuReference output levelBalanced OutputMIC: –58 dBuLINE: –12 dBuUnbalanced Output: –28 dBuPower requirementsExternal DC input: 12 V DCConsumption current (during 12 V DC input)220 mADimensions168 × 44 × 96 mm (6 5/8 × 1 3/4 × 37/8 inches) (w/h/d)Mass Approx. 510 g (1 lb. 2.0 oz.)DWZ-B30GBCarrier frequencies2402.0 MHz to 2478.5 MHzOccupied RF bandwidth2.5 MHzType of emissionF1D and F1EModulation methodGFSKOperating temperature0 °C to 50 °C (32 °F to 122 °F)Storage temperature–20 °C to +60 °C (–4 °F to +130 °F)Body-pack transmitter (ZTX-B01)RF output level10 mW (e.i.r.p.)Antennaλ/4 monopole antennaFrequency response10 Hz to 22 kHzMaximum input levelMIC: –22 dBuINST: +8 dBu(when attenuator level is 0 dB)Reference input levelMIC: –58 dBuINST: –28 dBu(when attenuator level is 0 dB)Dynamic rangeMIC: 102 dB (A-weighted)INST: 98 dB (A-weighted)Power requirements3.0 V DC (two LR6 (size AA) alkaline dry cell batteries)Battery lifeApprox. 10 hours of continuous use (25 °C (77 °F) ambient temperature, Sony LR6 (size AA) alkaline dry cell batteries)9644168Unit: mm00DWZ.book  Page 44  Saturday, August 25, 2012  6:23 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)45SpecificationsDimensions63 × 80 × 20 mm (2 1/2 × 3 1/4 × 13/16 inches) (w/h/d) (excluding the antenna)Mass Approx. 156 g (5.5 oz.) including batteriesCompact receiver (ZRX-C30)Reception typeSpace diversityAntennaInternal λ/4 monopole antennaFrequency response10 Hz to 22 kHzMaximum output levelBalanced Output: +16 dBuMain/Tuner Output: +8 dBuReference output levelBalanced Output: –20 dBuMain/Tuner Out: –28 dBuPower requirementsExternal DC input: 12 V DC / 9 V DCDry cell battery: Square 9 V alkaline dry cell battery (6LR61)Consumption currentDuring 12 V DC input: 90 mADuring 9 V DC input: 120 mABattery lifeApprox. 3.5 hours of continuous use (25 °C (77 °F) ambient temperature, Sony square 9 V alkaline dry cell battery)Dimensions132 × 41 × 74 mm (5 1/4 × 1 5/8 × 3inches) (w/h/d)Mass Approx. 205 g (7.2 oz.) (including battery)63 208010313Unit: mm41 13274Unit: mm00DWZ.book  Page 45  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:LeftDWZ-M50/B30GB4-445-504-11 (1)46 Specifications00DWZ.book  Page 46  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB04BAS.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)47Specifications00DWZ.book  Page 47  Wednesday, August 15, 2012  3:38 PM
E:\#works_2\120700180_DWZ-M50_B30GB\120700180_4445504111_GB\4445504111\4445504111DWZM50UC\01GB05BCO.fmmasterpage:RightDWZ-M50/B30GB4-445-504-11 (1)Sony CorporationPrinted in Korea00DWZ.book  Page 48  Wednesday, August 15, 2012  3:38 PM

Navigation menu