Sony ICD B17 B7/B17 User Manual Operating Instructions ICDB17
ICD-B7 Operating Instructions (primary manual) ICDB7
User Manual: Sony ICD-B17 Operating Instructions
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
3-250-691-12 (1) BGetting started BBasic Operations IC Recorder 1 Operating Instructions Replacing the batteries Slide and lift the battery compartment lid. Owner’s Record The model number is located at the rear and the serial number is located inside the battery compartment. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. ICD-B7/B17 The battery indicator on the display window shows the battery condition. flashes, replace the When batteries with new ones. flashes, the batteries are When exhausted and the unit will stop operation. 2 Battery life* Serial No. 1 2 ICD-B7/B17 Sony Corporation 2003 Printed in China Insert two LR03 (size AAA) alkaline batteries with correct polarity , and close the lid. Information Troubleshooting IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT. Before taking the unit for repair, check the following sections. Should any problem persist after you have made these checks, consult your nearest Sony dealer. The unit does not operate. For the customers in the U.S.A. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. • The batteries have been inserted with incorrect polarity. • The batteries are weak. • The buttons are locked with the HOLD switch. (If you press any button, “HOLD” will flash three times.) No sound comes from the speaker. If the battery compartment lid is accidentally detached, attach it as illustrated. On power • Operate the unit only on 3 V DC. Use two LR03 (size AAA) alkaline batteries. On safety • Do not operate the unit while driving, cycling or operating any motorized vehicle. On handling • Do not leave the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Should any solid object or liquid fall into the unit, remove the batteries and have the unit checked by qualified personnel before operating it any further. On noise • Noise may be heard when the unit is placed near an AC power source, a fluorescent lamp or a mobile phone during recording or playback. • Noise may be recorded when an object, such as your finger, etc., rubs or scratches the unit during recording. On maintenance • To clean the exterior, use a soft cloth slightly moistened in water. Do not use alcohol, benzine or thinner. With continuous use, approx. 10 hours recording/8 hours playback is possible. * Using Sony alkaline batteries LR03 (size AAA) * When playing back through the internal speaker with VOL control at around 4 The battery life may shorten depending on the operation of the unit. “FULL” is displayed and you cannot start recording. • The memory is full. Erase some of the messages. • 99 messages has been recorded in the selected folder. Select another folder or erase some of the messages. Noise is heard. • An object, such as your finger, etc., accidentally rubbed or scratched the unit during recording so that noise was recorded. • The unit was placed near an AC power source, a fluorescent lamp or a mobile phone during recording or playback. • Plug of the connected microphone was dirty when recording. Clean the plug. • Earphone/headphones plug is dirty. Clean the plug. • Do not use manganese batteries for this unit. • When you replace the batteries, insert the new ones within 3 minutes after you removed the exhausted ones. Otherwise, the display may show the clock setting display or incorrect date and time when you reinsert the batteries. In this case, set the date and time again. The recorded messages and alarm setting, however, will remain. • When replacing the batteries, be sure to replace both batteries with new ones. • Do not charge dry batteries. • When you are not going to use the unit for a long time, remove the batteries to prevent damage from battery leakage and corrosion. Step 2: Setting the Clock Clock setting display appears when you insert batteries for the first time, or when you insert battery after the unit has been without battery for a certain period of time. In this case, proceed from step 2. 1 1 Press MENU to enter the menu mode. • The date of recording will not be displayed if you recorded the message when the clock was not set. 3 Press NxPLAY/STOP. The year digits will flash. * The “ALARM” display may appear instead of the “BEEP” display . 2 Set the date . 1 Press – . or >+ to select the digits of the year. • You cannot add an index in a folder which has 99 messages. • If you add indexes frequently, the unit may become unable to add indexes. • You cannot add an index in the first or the last 1 second of a message. 2 Press NxPLAY/STOP. The month digits will flash. 3 Set the month and day in sequence, then press NxPLAY/STOP. The hour digits will flash. You cannot erase the index. 1 Tip • If you erase indexes frequently, the unit may become unable to erase indexes. To set the date to Year 2003, display “03Y”. If you have any questions or problems concerning your unit, please consult your nearest Sony dealer. Please note that recorded messages may be erased during service or repair work. 1 Select the folder . Current folder Press FOLDER to display the folder in which you wish to record messages. 2 3 Set the time . 1 Press – . or >+ to select the digits of the hour. 3 Set the minute. • Take out the battery and insert it again. 2 Press NxPLAY/STOP. The minute digits will flash. To avoid potential risk of data loss caused by accidental operation or malfunction of the IC recorder, we recommend that you save a backup copy of your recorded messages on a tape recorder, etc. 4 Press NxPLAY/STOP at the time signal. The display will return to “SET DATE”. 5 Press MENU to exit from the menu mode. 1 Tip This unit does not have a power on/off switch. The display is shown at all times. When playing back a previously recorded message, start from Step 1. When playing back a message you have just finished recording, start from Step 3. Note on recording Noise may be recorded if an object, such as your finger, etc., accidentally rubs or scratches the unit during recording. Maximum recording time Note Before making a long recording, be sure to insert new batteries and check the battery indicator. Start recording. 1 Press zREC/STOP. Current message number OPR indicator (lights in red during recording.) 2 Speak to the built-in microphone. Remaining memory indicator Counter display* * The display selected with the DISPLAY button appears. You can record for up to 150 minutes (ICD-B7)/300 minutes (ICD-B17). You can check the remaining amount of recording time by selecting the remaining recording time display mode. 3 Remaining memory indication During recording, the remaining memory indicator decreases one by one. Current folder Press FOLDER to display the folder you wish to play back. Playing the beginning of each message — Scanning Play 2 Select the message number . Press – . or >+ to display the desired message number. Selected message number – .: for smaller message number >+: for larger message number Counter display* * The display selected with the DISPLAY button appears (see the reverse side). 3 Press zREC/STOP again. The unit stops at the beginning of the current recording. XPAUSE To Do this stop recording Press STOP instead of zREC/STOP. pause recording* Press XPAUSE. During recording pause, the OPR indicator flashes in red and “PAUSE” flashes in the display window. release pause and resume recording Press XPAUSE or zREC/STOP. Recording resumes from that point. (To stop recording after pausing recording, press STOP.) listen to the current recording Press zREC/STOP or STOP to stop recording, then press NxPLAY/STOP. review the current recording instantly Press NxPLAY/STOP during recording. You can select the microphone sensitivity to display the following by pressing MIC SENS. HIGH: To record at meeting or in a quiet and/or spacious place. LOW: To record for dictation or in a noisy place. When the remaining time of recording reaches 5 minutes, the last one of the indication flashes. When the remaining time of recording reaches 1 minute, the selected display mode and “REMAIN” will flash one after the other in the display window. When the memory is full, recording automatically stops and “FULL” will flash in the display window with an alarm sound. To continue recording, first erase some of the messages. Notes • If you press zREC/STOP when the memory is full, “FULL” will flash with an alarm sound. Erase some of the messages before you start recording again. • If you press zREC/STOP after you have recorded 99 messages, “FULL” will flash with an alarm sound. Select another folder or erase some of the messages. Starting recording automatically in response to the sound — Advanced VOR function (ICD-B17 only) When VOR (voice operated recording) is set to ON in the menu, recording starts when the recorder detects sound. (“VOR” is displayed in the display window.) Recording stops when no sound is heard. (“VOR PAUSE” flashes in the display window.) Note VOR function is affected by the sound around you. Set the MIC SENS to HIGH or LOW. If recording is not satisfactory after you have changed the microphone sensitivity, or for important recording, set VOR to OFF. During stop mode, press NxPLAY/STOP for more than one second. “SCAN” will be displayed in the display window and the first 5 seconds of each message in the selected folder will be played back. When you find the desired message, press NxPLAY/STOP. The message will be played back until the end. Playing back all messages in a folder continuously — Continuous Play Start playback. EAR jack 1 Press NxPLAY/STOP. OPR indicator (lights in green during playback.) Flashing MIC SENS select the microphone sensitivity Select the folder . The memory is nearly full. Stop recording. NxPLAY/STOP 1 Playing back a message repeatedly — Repeat Play During playback, press NxPLAY/STOP for more than one second. “ “ will be displayed and the selected message will be played back repeatedly. To resume normal playback, press NxPLAY/STOP again. To stop playback, press STOP. Notes Due to the limitation of the IC recording system, this unit records in the minimum recording unit of approx. 9 seconds, therefore the following symptoms may occur: • When a message is shorter than the minimum recording unit, it is still counted as approx. 9 seconds so the remaining recording time will decrease by more than the actual length of the message. • When the message is longer than the minimum recording unit, the remaining recording time will decrease by more than the actual length of the message if it cannot be divided by the minimum recording unit without a remainder. •The sum of the number on the counter (elapsed recording time) and the remaining recording time may be less than the unit’s maximum recording time. You do not need to keep pressing zREC/STOP while recording. * About one hour after you pause recording, recording pause is automatically released and the unit goes into the stop mode. You cannot record messages up to the maximum recording time. The unit does not operate correctly. Blank space 2 Press – . once to display “SET DATE”. You cannot add an index. • No more recording can be made when 99 messages each have been recorded in both A and B folders. • Due to the limitation of the IC recording system, this unit records in the minimum recording unit of approx. 9 seconds. If the length of each message cannot be divided by the minimum recording unit, the remaining recording time may decrease by more than the total length of the messages. Message 2 Newly recorded message If you do not change the folder after you stop recording, the next time you record you will record in the same folder. Recording level is unstable (when recording music, etc.). “-M--D ---:--” is displayed on the REC DATE display. Message 1 STOP • Press MIC SENS to display “HIGH”. • You have not set the clock. e.g. Display the clock setting display. Recording level is low. “-M--D ---:--” is displayed. You can record up to 99 messages in each of the two folders (A and B). Since a newly recorded message is automatically added behind the last recorded message, you can start recording quickly without searching for the end of the last recording. Notes • The earphone or headphones are plugged in. • The volume is turned down completely. Keep personal credit cards using magnetic coding or springwound watches, etc., away from the unit to prevent possible damage from the magnet used in the speaker. Backup recommendations 1 Clock setting display appears when you insert batteries for the first time, or when you insert batteries after the unit has been without batteries for a certain period of time. Please refer to Steps 2 to 3 in “Step 2: Setting the Clock” to set the date and time. • This unit is designed to automatically adjust the recording level when recording meetings, etc., and is not suitable for music recording. Precautions 2 Playing Back Messages Recording Messages Step 1: Installing the Batteries Counter display (or the selected display mode) 2 Turn VOL to adjust the volume. STOP You can select the continuous play mode with the CONT in the menu. When you set CONT to ON, you can play back all messages in a folder continuously. Searching forward/ backward during playback (Cue/Review) To search forward, keep >+ pressed during playback and release the button at the point you wish to resume playback. To search backward, keep – . pressed during playback and release the button at the point you wish to resume playback. If you keep >+ or – .pressed for more than 10 seconds, the unit starts to search at higher speed. For the first 10 seconds of cue/ review, fast playback sound can be heard. When searching at a higher speed, playback sound will not be heard. During cue/review, the counter will be displayed, regardless of the display mode setting. ¡ Tip After playing back one message, the unit stops at the beginning of the next message. When the continuous play function is set to “ON” (see the reverse side), the unit stops after playing all messages in a folder. When the last message on a folder has been played back, the unit stops at the beginning of the last message. For private listening Connect an earphone or headphones (not supplied) to the EAR jack. The built-in speaker will be automatically disconnected. If you plug in headphones, you will get output from the left channel only. If noise is heard, wipe the headphones plug. Other operations To Do this stop at the beginning of the current message Press STOP. stop at the current position (Playback Pause function)* Press NxPLAY/STOP. To resume playback from that point, press NxPLAY/STOP again. go back to the beginning of the current message Press – . once. skip to the next message Press >+ once. go back to previous messages/skip to succeeding messages Press – . or >+ repeatedly. (During stop mode, keep the button pressed to skip the messages continuously.) * You can also pause playback by pressing XPAUSE instead of NxPLAY/STOP. The OPR indicator will flash in green. After about one hour, the unit goes into the stop mode at the current position. When fast playback is done to the end of the last message, “END” flashes 3 times. (You cannot hear the playback sound.) If you keep – . pressed while “END” is flashing, the messages are played back rapidly, and normal playback will start at the point you release the button. When “END” stops flashing and the OPR indicator goes off, the unit will stop at the beginning of the last message. If the last message is long and you wish to start playback at a later part of the message, keep >+ pressed to play back the message to the end and then press – . while “END” is flashing to go back to the desired point . (For messages other than the last one, go to the beginning of the next message and play backward to the desired point.) BVarious Ways of Recording Erasing Messages Adding a Recording to a Previously Recorded Message You can erase the recorded messages one by one or all messages in a folder at a time. Note that once a recording has been erased, you cannot retrieve it. You can add a recording to the message being played back. The added recording will be placed after the current message and counted as a part of the message. Erasing messages one by one During playback of Message 3 When a message is erased, the remaining messages will advance and renumbered so that there will be no space between messages. Before erasing Message 1 Message 2 Message 3 Message 4 After adding a recording Message 5 Erase Message 3 After erasing Message 1 Message 2 Message 3 Message 4 Message 3 Message 4 Message 3 Added recording Meeting at 2 o’clock on December 1. Message 4 at Conference room A Remaining messages are renumbered. To cancel erasing Press STOP before step 2. 1 Press ERASE while playing back the message you want to erase or press ERASE for more than 1 second during stop mode. A beep will sound and the message number and “ERASE” will flash while the first and last 5 seconds of the message is played back 10 times. Repeat steps 1 and 2. To erase a message partially First divide the message by adding an index and then follow the steps to erase the message. Dividing a Message by Adding an Index 1 Folder B Message 1 Message 2 Before adding an index Message 1 After adding an index Message 1 Message 2 Message 3 Message 3 Press STOP before step 3. We will now proceed to the next subject. The first item on the agenda is... Message 3 The new message number flashes three times at the point you pressed INDEX. The message will be divided in two messages; however, the messages will be recorded without a break. External microphone INDEX DISPLAY MIC SENS (microphone sensitivity) EAR, EARPHONE, v or REC OUT Follow the steps in “Recording messages” to record messages. Notes • Make sure that the plugs are connected securely. • We recommend you make a trial recording to check the connections and volume control. • When connecting equipment other than Sony’s, refer to the instruction manual of the equipment. MENU ERASE zREC (record) /STOP Starting recording automatically in response to the sound — Advanced VOR function (ICD-B17 only) – .REVIEW/ >+CUE VOR ON: NxPLAY/STOP• EXECUTE HOLD Speaker STOP VOR OFF: VOL (volume) 1 Rear The VOR (Voice Operated Recording) function is activated. Recording starts when the unit detects sound and stops when no sound is heard, eliminating recording from soundless period. The VOR function is disabled. Normal recording operation is selected. Press MENU to enter the menu mode. Display window Folder indication Alarm indicator Repeat play indicator Microphone sensitivity indication Battery compartment REC DATE (recorded date) indication REMAIN indicator Hook for handstrap (not supplied) Selected message number/Mode indication of the menu (ON, OFF, etc.) Press – . or >+ to display “VOR” and press NxPLAY/ STOP. “OFF (or ON)” will flash. REC (recording) indicator Remaining battery indicator 3 Remaining memory indicator Counter /Remaining time indication /Recording date indication /Current time indication (15:30, etc.) /Menu indication (ALARM, BEEP, etc.) /Messages (ERASE, HOLD, etc.) Press – . or >+ to select “ON” or “OFF” and press NxPLAY/STOP. Now the setting is completed. 4 The move function does not duplicate a message in another folder. When you move a message to another folder, the one in the previous folder will be deleted. Playing Back a Message at a Desired Time with an Alarm Press MENU to exit the menu mode. 2 Use FOLDER and – ./ >+ to select the folder and the message you want to play back. Enter the alarm setting mode. 1 Press MENU. The unit enters the menu mode and “ALARM OFF” will be displayed. (If “ALARM ON” is displayed, the alarm has been set. If you do not wish to change the setting, press MENU and exit the menu mode.) 1 Tip Note “ALARM OFF (or ON)” will not appear and the alarm cannot be set if the clock has not been set or no message has been recorded in the selected folder. 2 Press NxPLAY/STOP. “OFF” starts to flash. Select “ON” for “CONT” as described in “Playing Back All Messages in a Folder Continuously.” 3 Press – . or >+ to flash “ON”. Notes • If 99 messages have been recorded in a folder, you cannot add an index. In that case, reduce the number of messages to 98 or less by erasing unnecessary messages or by moving some of the messages to another folder before adding an index. • If you add an index to a message with an alarm setting, the alarm setting remains only with the former message divided. 4 Press NxPLAY/STOP. “DATE” will flash in the display window. Combining Messages by Erasing the Index You can combine two messages into one by erasing the index. Message 1 Message 2 Message 3 Message 4 Message 1 Message 2 Message 3 The message numbers decrease. The hour digits will flash. Selecting the Display Mode Set the alarm time. You can select the display mode for the stop, recording and playback modes. (If the unit is left unoperated for more than 3 seconds in the stop mode, the display will show the current time, regardless of the display mode setting.) Each time you press DISPLAY, the display mode will change as shown below: 5 1 Press – . or >+ to select the hour digits and press NxPLAY/STOP. The minute digits will flash. , 2 Press – . or >+ to select the minute digits and press NxPLAY/STOP. “ALARM ON” and “,” will be displayed to indicate that the setting has been completed. 6 3 Set the alarm date. To play back on a desired date (the message will be played back at the same time on the same date every year until you erase the message) 1 Press NxPLAY/STOP while “DATE” is flashing. The month digits will flash. 2 Press – . or >+ to display the number of the second of the two messages you want to combine. While pressing ERASE, press INDEX for more than 1 second. “ID ERASE” will flash for 10 seconds. 3 “,” is displayed when the number of the message with alarm setting is selected. At the set time, the alarm will sound for about 10 seconds and the selected message will be played back. During playback, “ALARM” will flash in the display window. When the playback ends, the unit will stop automatically at the beginning of that message. Press NxPLAY/STOP. The same message will be played back from the beginning. To cancel the alarm setting before the playback starts Press STOP while the alarm sound is heard. You can stop even when the HOLD function is activated. The two messages are combined into one and the messages will be renumbered as in the illustration above. Press – . or >+ to select the day of the week. Press STOP before step 3. To play back at the same time every day Notes on adding/erasing index Press – . or >+ to select “DAILY”. When recording with an IC recorder, the following symptoms may occur because of the limitation of the system, however, they are not malfunction. • If you add/erase indexes frequently, the unit may become unable to add/erase indexes. • You cannot add an index in the first or the last 1 second. • After combining messages by erasing an index, the latter message’s alarm setting will be erased. m 1 Press MENU to enter the menu mode. 2 Press – . or >+ to display “CONT” and press NxPLAY/ STOP. Remaining recording time: “OFF (or ON)” will flash. 3 Recorded date*: The date and time the current message was recorded. BEEP ON: A beep will sound to indicate that operation has been accepted. BEEP OFF: No beep sound will be heard except for the alarm and timer. 1 Press MENU to enter the menu mode. 2 Press – . or >+ to display “BEEP ON (or OFF)” and press NxPLAY/STOP. “ON (or OFF)” will flash. 3 Press – . or >+ to select “ON” or “OFF” and press NxPLAY/STOP. The setting is completed. 4 Press MENU to exit the menu mode. What beep sound means Beep patterns Meaning - (single tone) Usual mode -- (double tone) Enter/exit special mode 1 Select the message you set the alarm to play back, and press MENU. “ALARM ON” will be displayed. 2 Press NxPLAY/STOP to flash “ON”. 3 To cancel the alarm setting: Press – . or >+ to flash “OFF” and press NxPLAY/STOP. To change the alarm date and time: Press NxPLAY/STOP. When the alarm date is displayed, follow the steps 3 to 5 above to change the alarm date and time. 4 Press MENU to exit the menu mode. --- (triple tone) Notice* ---- (forth tone) Lack of battery power. HOLD Slide the HOLD switch in the direction of the arrow. “HOLD” will flash three times, indicating that all the functions of the buttons are locked. To cancel the HOLD function, simply slide the HOLD switch in the opposite direction. Note When the HOLD function is activated during recording, cancel the HOLD function first to stop recording. 1 Tip Even if the HOLD function is activated, you can stop the alarm playback. To stop the alarm or playback, press STOP. Now the setting is completed. 4 Press MENU to exit the menu mode. Turning off the Beep Sound To cancel the alarm setting or change the alarm time Preventing Accidental Operation — HOLD function Press – . or >+ to select “ON” or “OFF” and press NxPLAY/STOP. * If the clock has not been set, “-M--D ---:--” will be displayed. Notes • You cannot set the alarm if you have not set the clock or there is no message in the selected folder (the unit will not enter the alarm setting mode when you press MENU in Step 2). • If you try to set the alarm to play back a message at a previously set time on another message, “PRE SET” will be displayed, preventing new settings. • If the alarm time comes while another message is being played back with an alarm, the playback stops and the new message will be played back. • If the alarm time comes during recording, alarm will sound for 10 seconds after the recording is finished and playback begins. “,” will flash when the alarm time comes. • If more than one alarm time comes during recording, only the first message will be played back. • When the alarm time comes when the unit is in the menu mode, alarm will sound and the menu mode will be cancelled. • If you erase the message you set the alarm to play back, the alarm setting will be cancelled. • If you add an index to the message you set the alarm to play back, playback will stop at the index. • If you erase the index on the message you set the alarm to play back, the alarm setting will be cancelled. • You can adjust the playback volume with the VOL control. • If the alarm time comes during erasing, alarm will sound for 10 seconds after the erasing is finished and playback begins. • Alarm setting will not be cancelled when the alarm playback finishes. To cancel alarm setting, see below. 2 Press – . or >+ to select the month digits and press NxPLAY/STOP. The day digits will flash. 3 Press – . or >+ to select the day digits. To play back once a week Press ERASE while the display is flashing. CONT ON: You can play back all messages in a folder continuously. CONT OFF: Playback stops at the end of each message. m In stop mode, follow the steps below: 1 Playing Back All Messages in a Folder Continuously Counter: Elapsed playback/recording time in one message Press MENU to exit the menu mode. To listen to the same message again You can add an index after you have paused playback with XPAUSE. To cancel erasing 2 Press STOP before step 3. To play the divided messages continuously Tape recorder, TV, radio, etc. X PAUSE Press NxPLAY/STOP. To cancel moving the message(s) The message is divided in two and the new message number flashes three times. An index mark is added and the following index numbers will increase by one. Press –. or >+ to display the message number as the divided messages each have message numbers. Press NxPLAY/STOP. The message is moved in the destination folder. Messages are sorted in order of the recorded date and time. While playing back a message, press INDEX at the point you want to divide. An index is erased. FOLDER 3 To add an index during playback MIC Index to Parts and Controls Display window The first and last 5 seconds of the message will be played back 10 times, while the folder indication and “MOVE” flash. Recording continues When recording from other equipment Connecting cord RK-G64HG (not supplied) OPR (operation) indicator While playing back the message, press FOLDER to flash the indication of the folder to which you want to move the message (B in this case). 1 To play the message you marked with an index 3 While the display is flashing, press ERASE. MIC jack (PLUG IN POWER) EAR (earphone) jack 2 You can sound an alarm and start playback of a selected message at a desired time. Message 1 Message 2 Message 3 You can add an index during recording pause. When you connect an external microphone, the built-in microphone is automatically cut off. When a plug in power type microphone is connected, power is automatically supplied to the microphone from the IC recorder. 2 Play back the message you want to move. 1 Tip ECM-T115, etc. (not supplied) Main unit 1 Note When recording with an external microphone MIC Example: Moving Message 3 in Folder A to Folder B Message 4 The message numbers increase. 4 You can move the recorded messages to another folder. An index is added. Message 2 An index is added. To cancel erasing Message 3 Connect a plug-in-power type microphone or other equipment to the MIC (PLUG IN POWER) jack. Moving Messages to a Different Folder — Move Function You can add an index to a message during recording or playback. By dividing a message, you can easily find the point you want to play back when you make a long recording such as a meeting. When you add an index, the message numbers will increase as follows. Press zREC/STOP or STOP to stop the recording. Recording with an External Microphone or from Other Equipment 2 While pressing STOP, press ERASE for more than 1 second. “ALL ERASE” will flash for 10 seconds. MIC (built-in microphone) You can divide a message by adding an index, or combine messages by erasing the index. While recording/playing back messages, you can add an index (see below). In stop mode, you can erase the index. While recording a message, press INDEX at the point you want to divide. Message 1 Message 2 1 Press FOLDER to select the folder you want to erase. 2 Dividing a Message into Two/ Combining Messages — Index Function To mark an index during recording Erasing all messages in a folder Blank space During playback, press zREC/ STOP for more than 1 second. The REC indicator appears and “PLUS” flashes three times on the display window. The OPR indicator will turn red. The new recording will be added at the end of the current message. To erase other messages 2 Press ERASE while the message is being played back. The message is erased and the remaining messages will be renumbered. (For example, if you erase Message 3, Message 4 will be renumbered as Message 3. When erasing is completed, the unit will stop at the beginning of the following message.) e.g. Folder A Message 1 Message 2 Message 3 Blank space 1 BOther Functions ---- ---- (continuous beep) Alarm set time has come. * This pattern lets you know the procedure is wrong or informs you of some messages, such as: - you are trying to record a message when you have already recorded up to the maximum recordable time or the maximum number of messages. - you reaches at the top of the first message or end of the last message in a folder. Specifications Recording media Built-in flash memory, Monaural recording Recording time ICD-B7: 150 minutes ICD-B17: 300 minutes Frequency response 150 Hz - 3,500 Hz Speaker approx. 3.2 cm (1 5/16 in.) dia. Power output 150 mW Input/Output •Earphone jack (minijack) for 8 - 300 ohms earphone/headphones •Microphone jack (minijack, monaural) Plug in power Minimum input level 0.6 mV 3 kilohms or lower impedance microphone Power requirements Two LR03 (size AAA) alkaline batteries: 3 V DC Dimensions (w/h/d) (not incl. projecting parts and controls) 44.5 × 105.3 × 14.0 mm (1 13/16 × 4 1/4 × 9/16 in.) Mass (incl. batteries) 68 g (2.4 oz) Optional accessories Electret Condenser Microphone ECM-T115, ECM-T6, ECM-Z60 Connecting cord RK-G64HG Your dealer may not handle some of the above listed optional accessories. Please ask the dealer for detailed information. Design and specifications are subject to change without notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2003:01:26 06:07:45Z Modify Date : 2003:01:26 15:09:11+09:00 Subject : Page Count : 2 Creation Date : 2003:01:26 06:07:45Z Mod Date : 2003:01:26 15:09:11+09:00 Producer : Acrobat Distiller 5.00 for Macintosh Author : Sony Corporation Keywords : Metadata Date : 2003:01:26 15:09:11+09:00 Creator : Sony Corporation Title : ICD-B7/B17 Description :EXIF Metadata provided by EXIF.tools