Sony MEXGS620BT Bluetooth Audio System User Manual MEX GS620BT
Sony Corporation Bluetooth Audio System MEX GS620BT
UserManual.wiki
>
Sony
>
MEXGS620BT User Manual
Users Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![7GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)Detaching the Front PanelYou can detach the front panel of this unit to prevent theft.1Press and hold OFF until the unit turns off, press the front panel release button , then pull the panel towards you to remove.Caution alarmIf you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used.Serial numbersMake sure the serial numbers on the bottom of the unit and the back of the front panel are matched correctly. Otherwise you cannot make BLUETOOTH pairing, connection and disconnection by NFC.Resetting the UnitBefore operating the unit for the first time, after replacing the car battery, or changing the connections, you must reset the unit.Press RESET on the inner panel with a ball-point pen, etc., after detaching the front panel.NoteResetting the unit will erase the clock setting and some stored contents.Setting the Clock1Press MENU, rotate the control dial to select [GENERAL], then press it.2Rotate the control dial to select [SET CLOCK-ADJ], then press it.The hour indication flashes.3Rotate the control dial to set the hour and minute.To move the digital indication, press SEEK +/–.4After setting the minute, press MENU.The setup is complete and the clock starts.To display the clockPress and hold DSPL.Getting StartedAttaching the front panel010COV.book Page 7 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-7.png)
![8GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)Preparing a BLUETOOTH DeviceYou can enjoy music, or perform handsfree calling depending on the BLUETOOTH compatible device such as a smartphone, cellular phone and audio device (hereafter “BLUETOOTH device” if not otherwise specified). For details on connecting, refer to the operating instructions supplied with the device.Before connecting the device, turn down the volume of this unit; otherwise, loud sound may result.By touching the control dial on the unit with an NFC* compatible smartphone, the unit is paired and connected with the smartphone automatically.* NFC (Near Field Communication) is a technology enabling short-range wireless communication between various devices, such as mobile phones and IC tags. Thanks to the NFC function, data communication can be achieved easily just by touching the relevant symbol or designated location on NFC compatible devices.For a smartphone with Android OS 4.0 or lower installed, downloading the app “NFC Easy Connect” available at Google Play™ is required. The app may not be downloadable in some countries/regions.1Activate the NFC function on the smartphone.For details, refer to the operating instructions supplied with the smartphone.2Touch the N-Mark part of the unit with the N-Mark part of the smartphone.Make sure that lights up on the display of the unit.To disconnect by One touchTouch the N-Mark part of the unit with the N-Mark part of the smartphone again.NotesWhen making the connection, handle the smartphone carefully to prevent scratches.One touch connection is not possible when the unit is already connected to another NFC compatible device. In this case, disconnect the other device, and make connection with the smartphone again.When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other.1Place the BLUETOOTH device within 1 m (3 ft) of this unit.2Press MENU, rotate the control dial to select [BLUETOOTH], then press it.3Rotate the control dial to select [SET PAIRING], then press it. 4Rotate the control dial to select [SET DEVICE 1]* or [SET DEVICE 2]*, then press it. flashes while the unit is in pairing standby mode.* [SET DEVICE 1] or [SET DEVICE 2] will be changed to the paired device name after pairing is complete.5Perform pairing on the BLUETOOTH device so it detects this unit.6Select [MEX-GS620BT] shown in the display of the BLUETOOTH device.If your model name does not appear, repeat from step 2.7If passkey* input is required on the BLUETOOTH device, input [0000].* Passkey may be called “Passcode,” “PIN code,” “PIN number” or “Password,” etc., depending on the device.When pairing is made, stays lit.Connecting with a Smartphone by One touch (NFC)Pairing and connecting with a BLUETOOTH device[0000]Input passkey010COV.book Page 8 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-8.png)
![9GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)8Select this unit on the BLUETOOTH device to establish the BLUETOOTH connection. or lights up when the connection is made.NoteWhile connecting to a BLUETOOTH device, this unit cannot be detected from another device. To enable detection, enter the pairing mode and search for this unit from another device.To start playbackFor details, see “Playing a BLUETOOTH Device” (page 13).To disconnect the paired devicePerform steps 2 to 4 to disconnect after this unit and the BLUETOOTH device are paired.To use a paired device, connection with this unit is required. Some paired devices will connect automatically.1Press MENU, rotate the control dial to select [BLUETOOTH], then press it.2Rotate the control dial to select [SET BT SIGNL], then press it.Make sure that lights up.3Activate the BLUETOOTH function on the BLUETOOTH device.4Operate the BLUETOOTH device to connect to this unit. or lights up.Icons in the display:To connect the last-connected device from this unitActivate the BLUETOOTH function on the BLUETOOTH device.To connect with the audio device, press SRC to select [BT AUDIO] and press PAUSE.To connect with the cellular phone, press CALL.NoteWhile streaming BLUETOOTH audio, you cannot connect from this unit to the cellular phone. Connect from the cellular phone to this unit instead.TipWith BLUETOOTH signal on: when the ignition is turned to on, this unit reconnects automatically to the last-connected cellular phone.To install the microphoneFor details, see “Installing the microphone” (page 34).When an iPhone/iPod with iOS5 or later installed is connected to the USB port, the unit is paired and connected with the iPhone/iPod automatically.To enable BLUETOOTH Auto Pairing, make sure [AUTOPAIR] in [BLUETOOTH] is set to [ON] (page 22).1Activate the BLUETOOTH function on the iPhone/iPod.2Connect an iPhone/iPod to the USB port.Make sure that lights up on the display of the unit.NotesBLUETOOTH Auto Pairing is not possible if the unit is already connected to another BLUETOOTH device. In this case, disconnect the other device, then connect the iPhone/iPod again.If BLUETOOTH Auto Pairing is not established, see “Preparing a BLUETOOTH Device” for details (page 8).Connecting with a paired BLUETOOTH deviceLights up when handsfree calling is available by enabling the HFP (Handsfree Profile).Lights up when the audio device is playable by enabling the A2DP (Advanced Audio Distribution Profile).Connecting with an iPhone/iPod (BLUETOOTH Auto Pairing)010COV.book Page 9 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-9.png)
![10GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)Connecting a USB Device1Turn down the volume on the unit.2Connect the USB device to the unit.To connect an iPod/iPhone, use the USB connection cable for iPod (not supplied).Connecting Other Portable Audio Device1Turn off the portable audio device.2Turn down the volume on the unit.3Connect the portable audio device to the AUX input jack (stereo mini jack) on the unit with a connecting cord (not supplied)*.* Be sure to use a straight type plug.4Press SRC to select [AUX].To match the volume level of the connected device to other sourcesStart playback of the portable audio device at a moderate volume, and set your usual listening volume on the unit.Press MENU, then select [SOUND] [SET AUX VOL] (page 21).Listening to the RadioTo listen to the radio, press SRC to select [TUNER].1Press MODE to change the band (FM1, FM2, FM3, AM1 or AM2).2Press MENU, rotate the control dial to select [GENERAL], then press it.3Rotate the control dial to select [SET BTM], then press it.The unit stores stations in order of frequency on the number buttons.1Press MODE to change the band (FM1, FM2, FM3, AM1 or AM2).2Perform tuning.To tune manuallyPress and hold SEEK +/– to locate the approximate frequency, then press SEEK +/– repeatedly to fine adjust to the desired frequency.To tune automaticallyPress SEEK +/–.Scanning stops when the unit receives a station.1While receiving the station that you want to store, press and hold a number button (1 to 6) until [MEM] appears.1Select the band, then press a number button (1 to 6).Listening to the RadioStoring automatically (BTM)TuningStoring manuallyReceiving the stored stations010COV.book Page 10 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-10.png)
![11GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)Using Radio Data System (RDS)1Press PTY during FM reception.2Rotate the control dial until the desired program type appears, then press it.The unit starts to search for a station broadcasting the selected program type.Type of programsThe CT data from the RDS transmission sets the clock.1Set [SET CT-ON] in [GENERAL] (page 20).Listening to the SiriusXM Radio Only SiriusXM brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Connect Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.comAfter installing your SiriusXM Connect Vehicle Tuner and antenna, press SRC to select [SIRIUSXM]. You should be able to hear the SiriusXM preview channel on Channel 1. After verifying that you can hear the preview channel, select Channel 0 to find the Radio ID of your tuner. In addition, the Radio ID is located on the bottom of the SiriusXM Connect Vehicle Tuner and its packaging. You will need this number to activate your subscription. Write the number down for reference.In the USA, you can activate online or by calling SiriusXM Listener Care:Online: Visit www.siriusxm.com/activatenowPhone: Call 1-866-635-2349In Canada, you can activate online or by calling SiriusXM Listener Care:Online: Visit www.siriusxm.ca/activatexmPhone: Call 1-877-438-9677As part of the activation process, the SiriusXM satellites will send an activation message to your tuner. When your radio detects that the tuner has received the activation message, your radio will display: [SUBSCRIPTION UPDATED - PRESS ENT TO CONTINUE]. Once subscribed, you can tune to channels in your subscription plan.NotesThe activation process usually takes 10 to 15 minutes, but may take up to an hour.Your radio will need to be turned on and receiving the SiriusXM signal to receive the activation message.1Press (browse).2Rotate the control dial to select the desired channel, then press it.To select channels from categories1Press CAT.2Rotate control dial to select the desired category, then press it.3Rotate the control dial to select the desired channel, then press it.To store channels1While receiving the channel that you want to store, press and hold a number button (1 to 6) until [MEM] appears.To receive the stored channel, press MODE to select [SX1], [SX2] or [SX3], then press a number button (1 to 6).Selecting program types (PTY)NEWS (News), INFORM (Information), SPORTS (Sports), TALK (Talk), ROCK (Rock), CLS ROCK (Classic Rock), ADLT HIT (Adult Hits), SOFT RCK (Soft Rock), TOP 40 (Top 40), COUNTRY (Country), OLDIES (Oldies), SOFT (Soft), NOSTALGA (Nostalgia), JAZZ (Jazz), CLASSICL (Classical), R & B (Rhythm and Blues), SOFT R&B (Soft Rhythm and Blues), LANGUAGE (Foreign Language), REL MUSC (Religious Music), REL TALK (Religious Talk), PERSNLTY (Personality), PUBLIC (Public), COLLEGE (College), HABL ESP (Spanish Talk), MUSC ESP (Spanish Music), HIP HOP (Hip-Hop), WEATHER (Weather)Setting clock time (CT)Activating your SiriusXM SubscriptionSelecting channels for SiriusXM010COV.book Page 11 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-11.png)
![12GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)To set a parental controlThe parental control feature allows you to limit access to SiriusXM channels with mature content. When enabled, the parental control feature requires you to enter a passcode to tune to the locked channels. Information on setting up the passcode and locking channels can be found below.1Press MENU and rotate the control dial.2Select [GENERAL] [SXM PARENTAL] [LOCK SELECT] [LOCK-ON].3Enter the passcode by rotating the control dial on the unit or pressing / on the remote commander.To move the entry position, press SEEK +/– on the unit or / on the remote commander.The initial passcode is [0000].4After entering the passcode, press ENTER.To unlock the channels, select [LOCK-OFF].To change the passcode1Press MENU and rotate the control dial.2Select [GENERAL] [SXM PARENTAL] [CODE EDIT].3Enter the current passcode on the current passcode input display, then press ENTER.The initial passcode is [0000].4Enter your new 4-digit passcode on the new passcode input display, then press ENTER.To change display itemsPress and hold DSPL, then press DSPL again to change as follows:Channel Number (Default) Channel Name Artist Name Song Title Content Info Category Name ClockPlaying a Disc1Insert the disc (label side up).Playback starts automatically.Playing a USB DeviceIn these Operating Instructions, “iPod” is used as a general reference for the iPod functions on an iPod and iPhone, unless otherwise specified by the text or illustrations.For details on the compatibility of your iPod, see “About iPod” (page 23) or visit the support site on the back cover.MSC (Mass Storage Class) and MTP (Media Transfer Protocol) type USB devices* compliant with the USB standard can be used. Some digital media players or Android smartphones may require setting to MTP mode.* e.g., a USB flash drive, digital media player, Android smartphoneNotesFor details on the compatibility of your USB device, visit the support site on the back cover.Playback of the following files is not supported.MP3/WMA/AAC/FLAC:copyright-protected filesDRM (Digital Rights Management) filesMulti-channel audio filesMP3/WMA/AAC:lossless compression filesWAV:Multi-channel audio files1Connect a USB device to the USB port (page 10).Playback starts.If a device is already connected, to start playback, press SRC to select [USB1] for the USB port on the front, [USB2] for the USB port on the rear ([IPD] appears in the display when the iPod is recognized).2Adjust the volume on this unit.Playback010COV.book Page 12 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-12.png)
![13GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)To stop playbackPress and hold OFF for 1 second.To remove the deviceStop playback, then remove the device.Caution for iPhoneWhen you connect an iPhone via USB, phone call volume is controlled by the iPhone, not the unit. Do not inadvertently increase the volume on the unit during a call, as a sudden loud sound may result when the call ends.Playing a BLUETOOTH DeviceYou can play contents on a connected device that supports BLUETOOTH A2DP (Advanced Audio Distribution Profile).1Make BLUETOOTH connection with the audio device (page 8).To select the audio device, press MENU, then select [BLUETOOTH] [SET AUDIODEV] (page 22).2Press SRC to select [BT AUDIO].3Operate the audio device to start playback.4Adjust the volume on this unit.NotesDepending on the audio device, information such as title, track number/time and playback status may not be displayed on this unit.Even if the source is changed on this unit, playback of the audio device does not stop.[BT AUDIO] does not appear in the display while running the “SongPal” application via the BLUETOOTH function.To match the volume level of the BLUETOOTH device to other sourcesStart playback of the BLUETOOTH audio device at a moderate volume, and set your usual listening volume on the unit.Press MENU, then select [SOUND] [SET BTA VOL] (page 21).Searching and Playing Tracks1During playback, press (repeat) or (shuffle) repeatedly to select the desired play mode.Playback in the selected play mode may take time to start.Available play modes differ depending on the selected sound source.Not available when an iPod is connected.1During CD, USB or BT AUDIO*1 playback, press (browse)*2 to display the list of search categories.When the track list appears, press (back) repeatedly to display the desired search category.*1 Available only for audio devices supporting AVRCP (Audio Video Remote Control Profile) 1.4 or above.*2 During USB playback, press (browse) for more than 2 seconds to directly return to the beginning of the category list.2Rotate the control dial to select the desired search category, then press it to confirm.3Repeat step 2 to search the desired track.Playback starts.To exit the Quick-BrowZer modePress (browse).Repeat play and shuffle playSearching a track by name (Quick-BrowZer™)010COV.book Page 13 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-13.png)
![14GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)Not available when an iPod is connected.1Press (browse).2Press SEEK +.3Rotate the control dial to select the item.The list is jumped in steps of 10% of the total number of items.4Press ENTER to return to the Quick-BrowZer mode.The selected item appears.5Rotate the control dial to select the desired item, then press it.Playback starts.Pandora® is available to stream music through your iPhone and Android smartphone. You can control Pandora® on a BLUETOOTH connected iPhone/Android smartphone from this unit.Pandora® is only available in certain countries. Please visit http://www.pandora.com/legal for more information.Setting up Pandora®1Check the compatibility of your mobile device by visiting the support site on the back cover.2Download the latest version of the Pandora® application from your smartphone’s app store. A list of compatible devices can be found atwww.pandora.com/everywhere/mobileStreaming Pandora®1Connect the mobile device with this unit (page 8).To select the audio device, press MENU, then select [BLUETOOTH] [SET AUDIODEV] (page 22).2Press SRC to select [PANDORA].3Launch Pandora® application on your mobile device.4Press PAUSE to start playback.If the device number appearsMake sure that the same numbers are displayed (e.g., 123456) in this unit and the mobile device, then press ENTER on this unit and select [Yes] on the mobile device.When activating the BLUETOOTH functionYou can adjust the volume level.Press MENU, then select [SOUND] [SET BTA VOL] (page 21).Searching by skipping items (Jump mode) Listening to Pandora®010COV.book Page 14 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-14.png)
![15GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)Available Operations in Pandora®“Thumbs Up” or “Thumbs Down” feedback allows you to personalize stations.1During playback, press (Thumbs Up) or (Thumbs Down).The station list allows you to easily select a desired station.1During playback, press (browse).2Press SEEK + to select the sorting order [BY DATE] or [A TO Z].3Rotate the control dial to select the desired station, then press it.Playback starts.The track currently being played can be bookmarked and stored in your Pandora® account.1During playback, press MODE.To use a cellular phone, connect it with this unit. You can connect two cellular phones to the unit. For details, see “Preparing a BLUETOOTH Device” (page 8).Receiving a Call1Press CALL when a call is received with a ringtone.The phone call starts.NoteThe ringtone and talker’s voice are output only from the front speakers.To reject the callPress and hold OFF for 1 second.To end the callPress CALL again.Making a CallYou can make a call from the phonebook or call history when a cellular phone supporting PBAP (Phone Book Access Profile) is connected.When two cellular phones are connected to the unit, select either phone.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [PHONE BOOK], then press it.3Rotate the control dial to select an initial from the initial list, then press it.4Rotate the control dial to select a name from the name list, then press it.“Thumbs” feedbackUsing the station listBookmarkingHandsfree Calling (via BLUETOOTH only)From the phonebook010COV.book Page 15 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-15.png)
![16GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)5Rotate the control dial to select a number from the number list, then press it.The phone call starts.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [RECENT CALL], then press it.A list of the call history appears.3Rotate the control dial to select a name or phone number from the call history, then press it.The phone call starts.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [DIAL NUMBER], then press it.3Rotate the control dial to enter the phone number, and lastly select [ ] (space), then press ENTER*.The phone call starts.* To move the digital indication, press SEEK +/–.Note[_] appears instead of [#] on the display.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [REDIAL], then press it.The phone call starts.You can make a call by saying the voice tag stored in a connected cellular phone that has a voice dialing function.1Press CALL.When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it.2Rotate the control dial to select [VOICE DIAL], then press it.Alternatively, press VOICE while the “SongPal” function is off.3Say the voice tag stored on the cellular phone.Your voice is recognized, and the call is made.To cancel voice dialingPress VOICE.Available Operations during CallTo adjust the ringtone volumeRotate the control dial while receiving a call.To adjust the talker’s voice volumeRotate the control dial during a call.To adjust the volume for the other party (Mic gain adjustment)Press MIC.Adjustable volume levels: [MIC-LOW], [MIC-MID], [MIC-HI].To reduce echo and noise (Echo Canceler/Noise Canceler Mode)Press and hold MIC.Settable mode: [EC/NC-1], [EC/NC-2].To switch between handsfree mode and handheld modeDuring a call, press MODE to switch the phone call audio between the unit and cellular phone.NoteDepending on the cellular phone, this operation may not be available.From the call historyBy phone number inputBy redialBy voice tags010COV.book Page 16 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-16.png)
![17GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)SongPal with iPhone/Android smartphoneDownloading the latest version of “SongPal” application is required from the App Store for iPhone or from Google Play for Android smartphone.NotesFor your safety, follow your local traffic laws and regulations, and do not operate the application while driving.“SongPal” is an app for controlling Sony audio devices which are compatible with “SongPal”, by your iPhone/Android smartphone.What you can control with “SongPal” varies depending on the connected device.To make use of “SongPal” features, see the details on your iPhone/Android smartphone.For further details on “SongPal,” visit the following URL: http://rd1.sony.net/help/speaker/songpal/Visit the website below and check the compatible iPhone/Android smartphone models.For iPhone: visit the App StoreFor Android smartphone: visit Google Play 1Make the BLUETOOTH connection with iPhone/Android smartphone (page 8).To select the audio device, press MENU, then select [BLUETOOTH] [SET AUDIODEV] (page 22).2Launch the “SongPal” application.*13Press and hold APP on the unit for more than 2 seconds.*2Connection to iPhone/Android smartphone starts.For details on the operations on iPhone/Android smartphone, see the help of the application.*1 If [AUTO LAUNCH] in [SONGPAL] is set to [ON] (page 22), the “SongPal” connection is established automagically when the “SongPal” application is launched.*2 Alternatively, press MENU, then select [SONGPAL] [CONNECT] (page 22).If the device number appearsMake sure that the number is displayed (e.g., 123456), then select [Yes] on the iPhone/Android smartphone.To terminate connection1Press MENU, rotate the control dial to select [SONGPAL], then press it.2Rotate the control dial to select [CONNECT], then press it.Selecting the source or applicationYou can operate to select the desired source or application on iPhone/Android smartphone.To select the sourcePress SRC repeatedly. Alternatively, press SRC, rotate the control dial to select the desired source, then press ENTER.To display the source listPress SRC.Announcement of various information by voice guide (Android smartphone only)When SMS, Twitter/Facebook/Calendar notifications, etc., are received, they are automatically announced through the car speakers.For details on settings, refer to the help of the application.Useful FunctionsEstablishing the SongPal connection010COV.book Page 17 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-17.png)
![18GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)Activating voice recognition (Android smartphone only)By registering applications, you can control an application by voice command. For details, refer to the help of the application.To activate voice recognition1Press VOICE to activate voice recognition.2Say the desired voice command into the microphone when [Say Source or App] appears on the Android smartphone.NotesVoice recognition may not be available in some cases.Voice recognition may not work properly depending on the performance of the connected Android smartphone.Operate under conditions where noise such as engine sound is minimized during voice recognition.Replying a message of SMS (Android smartphone only)You can reply a message by voice recognition.1Activate voice recognition, then input “Reply.”The message input display appears on the “SongPal” application.2Input a reply message by voice recognition.The list of message candidates appears on the “SongPal” application.3Rotate the control dial to select the desired message, then press it.The message is sent out.Making sound and display settingsYou can adjust the settings relating to sound and display via iPhone/Android smartphone.For details on settings, refer to the help of the application.Using Siri Eyes FreeSiri Eyes Free allows you to use an iPhone handsfree by simply speaking into the microphone. This function requires you to connect an iPhone to the unit via BLUETOOTH. Availability is limited iPhone 4s or later. Make sure that your iPhone is running the latest iOS version. You must complete BLUETOOTH registration and connection configurations for the iPhone with the unit in advance. For details, see “Preparing a BLUETOOTH Device” (page 8).To select the iPhone, press MENU, then select [BLUETOOTH] [SET AUDIODEV] (page 22).1Activate the Siri function on the iPhone.For details, refer to the operating instructions supplied with the iPhone.2Press VOICE.The voice command display appears.3After the iPhone beeps, speak into the microphone.The iPhone beeps again, then Siri starts responding.To deactivate Siri Eyes FreePress VOICE.NotesThe iPhone may not recognize your voice depending on usage conditions. (For example, if you are in a moving car.)Siri Eyes Free may not function properly, or the response time may lag in locations where iPhone signals are difficult to receive. Depending on the iPhone’s operating condition, Siri Eyes Free may not function properly, or may quit.If you play a track with an iPhone using the BLUETOOTH audio connection, when the track starts playback via BLUETOOTH, Siri Eyes Free automatically quits and the unit switches to the BLUETOOTH audio source.When Siri Eyes Free is activated during audio playback, the unit may switch to the BLUETOOTH audio source even if you do not specify a track to play.When connecting the iPhone to the USB port, Siri Eyes Free may not function properly, or may quit.When connecting the iPhone to the unit via USB, do not activate Siri with the iPhone. Siri Eyes Free may not function properly, or may quit.There is no audio sound while Siri Eyes Free is activated.010COV.book Page 18 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-18.png)
![19GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)Canceling the DEMO ModeYou can cancel the demonstration display which appears when the source is off and the clock is displayed.1Press MENU, rotate the control dial to select [GENERAL], then press it.2Rotate the control dial to select [SET DEMO], then press it.3Rotate the control dial to select [SET DEMO-OFF], then press it.The setting is complete.4Press (back) twice.The display returns to normal reception/play mode.Basic Setting OperationYou can set items in the following setup categories:General setup (GENERAL), Sound setup (SOUND), Display setup (DISPLAY), BLUETOOTH setup (BT), SongPal setup (SONGPAL)1Press MENU.2Rotate the control dial to select the setup category, then press it.The items that can be set differ depending on the source and settings.3Rotate the control dial to select the options, then press it.To return to the previous displayPress (back).General Setup (GENERAL)DEMO (demonstration)Activates the demonstration: [ON], [OFF].CLOCK-ADJ (clock adjust) (page 7)CAUT ALM (caution alarm)Activates the caution alarm: [ON], [OFF] (page 7).(Available only while the source is off and the clock is displayed.)BEEPActivates the beep sound: [ON], [OFF].AUTO OFFShuts off automatically after a desired time when the unit is turned off: [ON] (30 minutes), [OFF].STEERINGRegisters/resets the setting of the steering wheel remote control. (Available when connected with the connection cable (not supplied).) (Available only while the source is off and the clock is displayed.)STR CONTROL (steering control)Selects the input mode of the connected remote control. To prevent a malfunction, be sure to match the input mode with the connected remote control before use.CUSTOMInput mode for the steering wheel remote controlPRESETInput mode for the wired remote control excluding the steering wheel remote control (automatically selected when [EDIT CUSTOM] is complete or [RESET CUSTOM] is performed)EDIT CUSTOMRegisters the functions (SOURCE, ATT, VOL +/–, SEEK +/–, VOICE, ON HOOK, OFF HOOK) to the steering wheel remote control:Rotate the control dial to select the function you want to assign to the steering wheel remote control, then press it.While [REGISTER] is blinking, press and hold the button on the steering wheel remote control you want to assign the function to. When registration is complete, [REGISTERED] is displayed.To register other functions, repeat steps and . (Available only when [STR CONTROL] is set to [CUSTOM].)RESET CUSTOMResets the setting of the steering wheel remote control: [YES], [NO].(Available only when [STR CONTROL] is set to [CUSTOM].)NotesWhile making settings, only button operation on the unit is available. For safety, park your car before making this setting.If an error occurs while registering, all the previously-registered information remains. Restart registration from the function where the error occurred.This function may not be available on some vehicles. For details on the compatibility of your vehicle, visit the support site on the back cover.Settings010COV.book Page 19 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-19.png)
![20GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)CT (clock time)Activates the CT function: [ON], [OFF].BTM (best tuning memory) (page 10)(Available only when the tuner is selected.)SXM PARENTALSets the parental lock to [ON], [OFF], and edits the passcode (page 12). (Available only when SiriusXM is selected.)SXM RESET (SiriusXM reset)Initializes the SiriusXM Connect Vehicle Tuner settings (preset channels/parental lock): [YES], [NO]. (Available only when SiriusXM is selected.)FIRMWARE(Available only while the source is off and the clock is displayed.) Checks/updates the firmware version. For details, visit the support site on the back cover.FW VERSION (firmware version)Displays current firmware version.FW UPDATE (firmware update)Enters firmware update process: [YES], [NO].Updating the firmware takes a few minutes to complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device.Sound Setup (SOUND)This setup menu is not available when the source is off and the clock is displayed.EXTRA BASS Reinforces bass sound in synchronization with the volume level: [1], [2], [OFF].(Automatically sets to [OFF] when [C.AUDIO+] is set to [ON].)C.AUDIO+ (ClearAudio+)Reproduces sound by optimizing the digital signal with the Sony recommended sound settings: [ON], [OFF]. (Automatically sets to [OFF] when [EQ10 PRESET] is changed and/or [EXTRA BASS] is set to [1] or [2] and/or [DSO] is set to [LOW], [MID] or [HIGH].)EQ10 PRESETSelects an equalizer curve from 10 equalizer curves or off:[OFF], [R&B], [ROCK], [POP], [DANCE], [HIP-HOP], [ELECTRONICA], [JAZZ], [SOUL], [COUNTRY], [CUSTOM].The equalizer curve setting can be memorized for each source.EQ10 CUSTOMSets [CUSTOM] of EQ10.Setting the equalizer curve: [BAND1] 32 Hz, [BAND2] 63 Hz, [BAND3] 125 Hz, [BAND4] 250 Hz, [BAND5] 500 Hz, [BAND6] 1 kHz, [BAND7] 2 kHz, [BAND8] 4 kHz, [BAND9] 8 kHz, [BAND10] 16 kHz.The volume level is adjustable in 1 dB steps, from -6 dB to +6 dB.POSITION (listening position)F/R POS (front/rear position)Simulates a natural sound field by delaying the sound output from speakers to suit your position: [FRONT L] (front left), [FRONT R] (front right), [FRONT] (center front), [ALL] (center of your car), [CUSTOM] (position set by the advanced car audio settings on SongPal) [OFF] (no position set)ADJ POSITION (adjust position)Fine-tunes the listening position setting: [+3] – [CENTER] – [-3].(Available only when [F/R POS] is not set to [OFF] or [CUSTOM].)SW POS (subwoofer position) [NEAR] (near), [NORMAL] (normal), [FAR] (far)(Available only when [F/R POS] is set to other than [OFF].)DSO (dynamic stage organizer)Creates a more ambient sound as if there were speakers in the dashboard: [OFF], [LOW], [MID], [HIGH].BALANCEAdjusts the sound balance: [RIGHT-15] – [CENTER] – [LEFT-15].FADERAdjusts the relative level: [FRONT-15] – [CENTER] – [REAR-15].DSEE (digital sound enhancement engine)Improves digitally compressed sound by restoring high frequencies lost in the compression process: [ON], [OFF].This setting can be memorized for each source other than the tuner.010COV.book Page 20 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-20.png)
![21GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)AAV (advanced auto volume)Adjusts the playback volume level of all playback sources to the optimum level: [ON], [OFF].RB ENH (rear bass enhancer)Rear Bass Enhancer enhances the bass sound by applying a low pass filter setting to the rear speakers. This function allows the rear speakers to work as a subwoofer if one is not connected.(Available only when [SW DIREC] is set to [OFF].)RBE MODE (rear bass enhancer mode)Selects the rear bass enhancer mode: [1], [2], [3], [OFF].LPF FREQ (low pass filter frequency)Selects the subwoofer cut-off frequency: [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].LPF SLOP (low pass filter slope)Selects the LPF slope: [1], [2], [3].SW DIREC (subwoofer direct connection)You can use the subwoofer without a power amplifier when it is connected to the rear speaker lead.(Available only when [RBE MODE] is set to [OFF].)Be sure to connect a 4 Ω – 8 Ω subwoofer to either of the rear speaker leads. Do not connect a speaker to the other rear speaker lead.SW MODE (subwoofer mode) Selects the subwoofer mode: [1], [2], [3], [OFF].SW PHASE (subwoofer phase) Selects the subwoofer phase: [NORM], [REV].SW POS (subwoofer position)Selects the subwoofer position: [NEAR], [NORMAL], [FAR].(Available only when [F/R POS] is set to other than [OFF].)LPF FREQ (low pass filter frequency) Selects the subwoofer cut-off frequency: [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].LPF SLOP (low pass filter slope) Selects the LPF slope: [1], [2], [3].S.WOOFER (subwoofer)SW LEVEL (subwoofer level)Adjusts the subwoofer volume level: [+10 dB] – [0 dB] – [-10 dB].([ATT] is displayed at the lowest setting.)SW PHASE (subwoofer phase)Selects the subwoofer phase: [NORM], [REV].SW POS (subwoofer position)Selects the subwoofer position: [NEAR], [NORMAL], [FAR].(Available only when [F/R POS] is not set to [OFF].)LPF FREQ (low pass filter frequency)Selects the subwoofer cut-off frequency: [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].LPF SLOP (low pass filter slope)Selects the LPF slope: [1], [2], [3].HPF (high pass filter)HPF FREQ (high pass filter frequency)Selects the front/rear speaker cut-off frequency: [OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].HPF SLOP (high pass filter slope)Selects the HPF slope (effective only when [HPF FREQ] is set to other than [OFF]): [1], [2], [3].AUX VOL (AUX volume level)Adjusts the volume level for each connected auxiliary device: [+18 dB] – [0 dB] – [-8 dB].This setting negates the need to adjust the volume level between sources.(Available only when the AUX is selected.)BTA VOL (BLUETOOTH audio volume level)Adjusts the volume level for each connected BLUETOOTH device: [+6 dB] – [0 dB] – [-6 dB].This setting negates the need to adjust the volume level between sources.(Available only when the BT audio, application or Pandora® is selected.)Display Setup (DISPLAY)DIMMERChanges the display brightness: [ON], [OFF], [CLK], [AT] (auto).([AT] is available only when the illumination control lead is connected, and the head light is turned on.)To set this function to be active only during a fixed period, select [CLK], then set the start and end times.To set the brightness when the dimmer function is activated:Set [DIMMER] to [ON], then adjust [BRIGHTNESS].To set the brightness when the dimmer function is deactivated:Set [DIMMER] to [OFF], then adjust [BRIGHTNESS].The brightness setting is stored and applied when the dimmer function is activated or deactivated.BRIGHTNESSAdjusts the display brightness. The brightness level is adjustable: [1] – [10].010COV.book Page 21 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-21.png)
![22GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)BUTTON-C (button color)Sets a preset color or customized color for the buttons.COLORSelects from 15 presets colors, 1 customized color.CUSTOM-C (custom color)Registers a customized color for the buttons.RGB RED, RGB GRN, RGB BLUEAdjustable color range: [0] – [32] ([0] cannot be set for all color ranges).DSPL-C (display color)Sets a preset color or customized color for the display.COLORSelects from 15 presets colors, 1 customized color.CUSTOM-C (custom color)Registers a customized color for the display.RGB RED, RGB GRN, RGB BLUEAdjustable color range: [0] – [32] ([0] cannot be set for all color ranges).SND SYNC (sound synchronization)Activates the synchronization of the illumination with the sound: [ON], [OFF].AUTO SCR (auto scroll)Scrolls long items automatically: [ON], [OFF].(Not available when the AUX or tuner is selected.)BLUETOOTH Setup (BLUETOOTH)PAIRING (page 8)Connects up to two BLUETOOTH devices: [DEVICE 1], [DEVICE 2].[DEVICE 1] or [DEVICE 2] will be changed to the paired device name after pairing is complete.AUDIODEV (audio device)Selects the audio device. [*] appears on the device paired with [DEVICE 1] or the current A2DP compatible audio device.RINGTONESelects whether this unit or the connected cellular phone outputs the ringtone: [1] (this unit), [2] (cellular phone).AUTO ANS (auto answer)Sets this unit to answer an incoming call automatically: [OFF], [1] (about 3 seconds), [2] (about 10 seconds).AUTOPAIR (auto pairing)Start BLUETOOTH pairing automatically when iOS device version 5.0 or later is connected via USB: [ON], [OFF].BT SIGNL (BLUETOOTH signal) (page 9)Activates/deactivates the BLUETOOTH function.BT INIT (BLUETOOTH initialize)Initializes all the BLUETOOTH related settings (pairing information, preset number, device information, etc.): [YES], [NO].When disposing the unit, initialize all the settings. (Available only while the source is off and the clock is displayed.)SongPal Setup (SONGPAL)AUTO LAUNCH Activates the “SongPal” auto launch: [ON], [OFF]. When [ON] is selected, “SongPal” will automatically connect after the BLUETOOTH connection is complete.CONNECTEstablish and terminate “SongPal” function (connection).010COV.book Page 22 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-22.png)
![26GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)SiriusXM Connect Vehicle Tuner and Subscription sold separately.www.siriusxm.comSirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners.The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.iPhone, iPod, iPod classic, iPod nano, iPod touch, and Siri are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.Pandora®, the Pandora® logo, and the Pandora® trade dress are trademarks or registered trademarks of Pandora Media, Inc., used with permission.Google, Google Play and Android are trademarks of Google Inc.libFLACCopyright (C) 2000-2009 Josh CoalsonCopyright (C) 2011-2013 Xiph.Org FoundationRedistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.TroubleshootingThe following checklist will help you remedy problems you may encounter with your unit.Before going through the checklist below, check the connection and operating procedures.For details on using the fuse and removing the unit from the dashboard, see “Connection/Installation” (page 32).If the problem is not solved, visit the support site on the back cover.GeneralNo power is being supplied to the unit.If the unit is turned off and the display disappears, the unit cannot be operated with the remote commander.Turn on the unit.No sound or the sound is very low.The position of the fader control [FADER] is not set for a 2-speaker system.The volume of the unit and/or connected device is very low.Increase the volume of the unit and connected device.No beep sound.An optional power amplifier is connected and you are not using the built-in amplifier.Copyrights010COV.book Page 26 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-26.png)
![27GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)The contents of the memory have been erased.The power supply lead or battery has been disconnected or not connected properly.Stored stations and correct time are erased.The fuse has blown.Makes a noise when the position of the ignition is switched.The leads are not matched correctly with the car’s accessory power connector.During playback or reception, the demonstration mode starts.If no operation is performed for 5 minutes with [DEMO-ON] set, the demonstration mode starts.Set [DEMO-OFF] (page 19).The display disappears from/does not appear in the display window.The dimmer is set to [DIM-ON] (page 21).The display disappears if you press and hold OFF.Press OFF on the unit until the display appears.The connectors are dirty (page 24).The display/illumination flashes.The power supply is not sufficient.Check that the car battery supplies enough power to the unit. (The power requirement is 12 V DC.)The operation buttons do not function.The disc will not eject.The connection is not correct.Check the connection of the unit.If the situation does not improve, press RESET (page 7). The contents stored in memory are erased.For your safety, do not reset the unit while you are driving.Radio receptionStations cannot be received.The sound is hampered by noises.The connection is not correct.If your car has built-in radio antenna (aerial) in the rear/side glass, connect an REM OUT lead (blue/white striped) or accessory power supply lead (red) to the power supply lead of a car’s antenna (aerial) booster.Check the connection of the car antenna (aerial).If the auto antenna (aerial) will not extend, check the connection of the power antenna (aerial) control lead.Preset tuning is not possible.The broadcast signal is too weak.RDSPTY displays [- - - - - - - -].The current station is not an RDS station.RDS data has not been received.The station does not specify the program type.CD playbackThe disc does not play.Defective or dirty disc.The CD-R/CD-RW is not for audio use (page 23).MP3/WMA/AAC files cannot be played.The disc is incompatible with the MP3/WMA/AAC format and version. For details on playable discs and formats, visit the support site on the back cover.MP3/WMA/AAC files take longer to play than others.The following discs take a longer time to start playback.A disc recorded with a complicated tree structure.A disc recorded in Multi Session.A disc to which data can be added.The sound skips.Defective or dirty disc.USB device playbackYou cannot play items via a USB hub.This unit cannot recognize USB devices via a USB hub.A USB device takes longer to play.The USB device contains files with a complicated tree structure.The sound is intermittent.The sound may be intermittent at a high-bit-rate.DRM (Digital Rights Management) files may not be playable in some cases.Audio file cannot be played.USB device formatted with file systems other than FAT16 or FAT32 are unsupported.** This unit supports FAT16 and FAT32, but some USB device may not support all of these FAT. For details, refer to the operating instruction of each USB device or contact the manufacturer.010COV.book Page 27 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-27.png)
![28GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)NFC functionOne touch connection (NFC) is not possible.If the smartphone does not respond to the touching.Check that the NFC function of the smartphone is turned on.Move the N-Mark part of the smartphone closer to the N-Mark part on this unit.If the smartphone is in a case, remove it.NFC receiving sensitivity depends on the device.If One touch connection with the smartphone fails several times, make BLUETOOTH connection manually.BLUETOOTH functionThe connecting device cannot detect this unit.Before the pairing is made, set this unit to pairing standby mode.While connected to a BLUETOOTH device, this unit cannot be detected from another device.Disconnect the current connection and search for this unit from another device.When the device pairing is made, set the BLUETOOTH signal output to on (page 9).Connection is not possible.The connection is controlled from one side (this unit or BLUETOOTH device), but not both.Connect to this unit from a BLUETOOTH device or vice versa.The name of the detected device does not appear.Depending on the status of the other device, it may not be possible to obtain the name.No ringtone.Adjust the volume by rotating the control dial while receiving a call.Depending on the connecting device, the ringtone may not be sent properly.Set [RINGTONE] to [1] (page 22).The front speakers are not connected to the unit.Connect the front speakers to the unit. The ringtone is output only from the front speakers.The talker’s voice cannot be heard.The front speakers are not connected to the unit.Connect the front speakers to the unit. The talker’s voice is output only from the front speakers.A call partner says that the volume is too low or high.Adjust the volume accordingly using mic gain adjustment (page 16).Echo or noise occurs in phone call conversations.Lower the volume.Set EC/NC Mode to [EC/NC-1] or [EC/NC-2] (page 16).If the ambient noise other than the phone call sound is loud, try reducing this noise.E.g.: If a window is open and road noise, etc., is loud, shut the window. If an air conditioner is loud, lower the air conditioner.The phone is not connected.When BLUETOOTH audio is played, the phone is not connected even if you press CALL.Connect from the phone.The phone sound quality is poor.Phone sound quality depends on reception conditions of cellular phone. Move your car to a place where you can enhance the cellular phone’s signal if the reception is poor.The volume of the connected audio device is low (high).Volume level will differ depending on the audio device.Adjust the volume of the connected audio device or this unit.The sound skips during playback of a BLUETOOTH audio device.Reduce the distance between the unit and the BLUETOOTH audio device.If the BLUETOOTH audio device is stored in a case which interrupts the signal, remove the audio device from the case during use.Several BLUETOOTH devices or other devices which emit radio waves are in use nearby.Turn off the other devices.Increase the distance from the other devices.The playback sound stops momentarily when the connection between this unit and the cellular phone is being made. This is not a malfunction.The connected BLUETOOTH audio device cannot be controlled.Check that the connected BLUETOOTH audio device supports AVRCP.Some functions do not work.Check if the connecting device supports the functions in question.A call is answered unintentionally.The connecting phone is set to answer a call automatically.Pairing failed due to a timeout.Depending on the connecting device, the time limit for pairing may be short.Try completing the pairing within the time.010COV.book Page 28 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-28.png)
![29GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)BLUETOOTH function cannot operate.Turn off the unit by pressing OFF for more than 2 seconds, then turn the unit on again.No sound is output from the car speakers during handsfree call.If the sound is output from the cellular phone, set the cellular phone to output the sound from the car speakers.Siri Eyes Free is not activated.Perform the handsfree registration for an iPhone that supports Siri Eyes Free.Set the Siri function on the iPhone to on.Cancel the BLUETOOTH connection with the iPhone and the unit, and reconnect.SongPal operationApplication name is mismatched with the actual application in “SongPal”.Launch the application again from the “SongPal” application.While running the “SongPal” application via BLUETOOTH, the display automatically switches to [BT AUDIO].The “SongPal” application or BLUETOOTH function has failed.Run the application again.The “SongPal” application is automatically disconnected when the display switches to [IPD].The “SongPal” application on iPhone/iPod does not support iPod playback.Change the source of the unit to other than [IPD], then establish the “SongPal” connection (page 17).Pandora® operationPandora® connection is not possible.Shut down the Pandora® application on the mobile device, and then launch it again.MessagesThe following messages may appear or flash during operation.CD ERROR: The disc cannot be played. The disc will be ejected automatically.Clean or insert the disc correctly, or make sure the disc is not blank or defective.CD NO MUSIC: There is no playable file. The disc will be ejected automatically.Insert a disc containing playable files (page 25).CD PUSH EJT: The disc could not be ejected properly.Press (eject).HUB NO SUPRT: USB hubs are not supported.IPD STOP: iPod playback has finished.Operate your iPod/iPhone to start playback.OVERLOAD: The USB device is overloaded.Disconnect the USB device, then press SRC to select another source. The USB device has a fault, or an unsupported device is connected.READ: Now reading information.Wait until reading is complete and playback starts automatically. This may take some time depending on the file organization.USB ERROR: The USB device cannot be played.Connect the USB device again.USB NO DEV: A USB device is not connected or recognized.Make sure the USB device or USB cable is securely connected.USB NO MUSIC: There is no playable file.Connect a USB device containing playable files (page 25).USB NO SUPRT: The USB device is not supported.For details on the compatibility of your USB device, visit the support site on the back cover. or : The beginning or the end of the disc has been reached. (underscore): The character cannot be displayed.For BLUETOOTH function:ERROR: The selected operation could not be performed.Wait for a while, then try again.NO DEV: The BLUETOOTH device is not connected or recognized.Make sure the BLUETOOTH device is securely connected, or the BLUETOOTH connection is established with the BLUETOOTH device.UNKNOWN: A name or phone number cannot be displayed.WITHHELD: The phone number is hidden by the caller.010COV.book Page 29 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-29.png)
![31GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)CHAN UNSUBThe channel that you have requested is not included in your SiriusXM subscription package or the channel that you were listening to is no longer included in your SiriusXM subscription package.If you have questions about your subscription package or would like to subscribe to this channel, please contact SiriusXM.In the USA, visit www.siriusxm.com or call 1-866-635-2349.In Canada, visit www.siriusxm.ca or call 1-877-438-9677.CHK ANTThe radio has detected a fault with the SiriusXM antenna.The antenna cable may be either disconnected or damaged.Verify that the antenna cable is connected to the SiriusXM Connect Vehicle Tuner.Inspect the antenna cable for damage and kinks.Replace the antenna if the cable is damaged. SiriusXM products are available at your local car audio retailer or online at - www.shop.siriusxm.comCHECK TUNERThe radio is having difficulty communicating with the SiriusXM Connect Vehicle Tuner.The tuner may be disconnected or damaged.Verify that the SiriusXM Connect Vehicle Tuner cable is securely connected to the radio.NO SIGNALSiriusXM Connect Vehicle Tuner is having difficulty receiving the SiriusXM satellite signal.Verify that your vehicle is outdoors with a clear view of the sky.Verify that the SiriusXM magnetic mount antenna is mounted on a metal surface on the outside of the vehicle.Move the SiriusXM antenna away from any obstructions.Inspect the antenna cable for damage and kinks.Consult the SiriusXM Connect Vehicle Tuner installation manual for more information on antenna installation.Replace the antenna if the cable is damaged. SiriusXM products are available at your local car audio retailer or online at - www.shop.siriusxm.comSUBSCRIPTION UPDATE - PRESS ENT TO CONTINUEThe radio has detected a change in your SiriusXM subscription status.Press ENTER to clear the message.If you have questions about your subscription, please contact SiriusXM.In the USA, visit www.siriusxm.com or call 1-866-635-2349.In Canada, visit www.siriusxm.ca or call 1-877-438-9677.For steering wheel remote control operation:ERROR: An error occurred during the function registration.Register again from the function where the error occurred (page 19).TIMEOUT: The function registration failed due to a timeout.Try completing the registration while [REGISTER] is blinking (about 6 seconds) (page 19).If these solutions do not help improve the situation, consult your nearest Sony dealer.If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began.010COV.book Page 31 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-31.png)
![34GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: LeftMEX-GS620BT4-687-334-11(1)To a common ground (earth) pointFirst connect the black ground (earth) lead, then connect the yellow and red power supply leads.To the +12 V power terminal which is energized at all timesBe sure to first connect the black ground (earth) lead to a common ground (earth) point.To the +12 V power terminal which is energized when the ignition switch is set to the accessory positionIf there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times.Be sure to first connect the black ground (earth) lead to a common ground (earth) point.To the power antenna (aerial) control lead or the power supply lead of the antenna (aerial) boosterIt is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial).To AMP REMOTE IN of an optional power amplifierThis connection is only for amplifiers and a power antenna (aerial). Connecting any other system may damage the unit.To a car’s illumination signalBe sure to first connect the black ground (earth) lead to a common ground (earth) point.Subwoofer Easy ConnectionYou can use a subwoofer without a power amplifier when it is connected to a rear speaker cord.NoteUse a subwoofer with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.Memory hold connectionWhen the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.Speaker connectionBefore connecting the speakers, turn the unit off.Use speakers with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.To capture your voice during handsfree calling, you need to install the microphone .CautionsIt is extremely dangerous if the cord becomes wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations.If airbags or any other shock-absorbing equipment is in your car, contact the store where you purchased this unit, or the car dealer, before installation.NoteBefore attaching the double-sided tape , clean the surface of the dashboard with a dry cloth.When using the steering wheel remote controlInstallation of the connection cable RC-SR1 (not supplied) is required before use.1To enable the steering wheel remote control, select [SET STEERING] [EDIT CUSTOM] to make the registration (page 19).When the registration completes, the steering wheel remote control becomes available.Making connectionsFront speakerSubwooferInstalling the microphoneUsing the wired remote controlClip (not supplied)010COV.book Page 34 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-34.png)
![35GBC:\Works\4687334111\4687334111MEXGS620BTUC\01GB-MEX-GS620BTUC\030CD.fm masterpage: RightMEX-GS620BT4-687-334-11(1)Notes on installing the connection cable RC-SR1 (not supplied)Refer to the support sites on the back cover for details, then connect each lead properly to the appropriate leads. Making an improper connection may damage the unit.Depending on the type of car, be sure to insulate the unused leads with electrical tape for safety.Do not connect this cable when the steering wheel remote control is not used.Consulting the dealer or an experienced technician for help is recommended.When using the wired remote control1To enable the wired remote control, set [STR CONTROL] in [SET STEERING] to [PRESET] (page 19).InstallationBefore installing the unit, remove the protection collar and the bracket from the unit.1Pinch both edges of the protection collar , then pull it out.2Insert both release keys until they click, and pull down the bracket , then pull up the unit to separate.Before installing, make sure the catches on both sides of the bracket are bent inwards 2 mm (3/32 in).For Japanese cars, see “Mounting the unit in a Japanese car” (page 36).1Position the bracket inside the dashboard, then bend the claws outward for a tight fit.2Mount the unit onto the bracket , then attach the protection collar .NotesIf the catches are straight or bent outwards, the unit will not be installed securely and may spring out.Make sure the 4 catches on the protection collar are properly engaged in the slots of the unit.Removing the protection collar and the bracketFace the hook inwards.Mounting the unit in the dashboard182 mm (7 1/4 in)53 mm (2 1/8 in)Catch010COV.book Page 35 Monday, September 5, 2016 7:34 PM](https://usermanual.wiki/Sony/MEXGS620BT/User-Guide-3174236-Page-35.png)
