Sony PM-0741 GSM/UMTS Mobile Phone with WLAN, BT, RFID Ant+ User Manual SAR Leaflet

Sony Mobile Communications Inc GSM/UMTS Mobile Phone with WLAN, BT, RFID Ant+ SAR Leaflet

Contents

08 safety leaflet

付録／索引
Important Information United
States
THIS PHONE MODEL HAS BEEN
CERTIFIED IN COMPLIANCE WITH THE
GOVERNMENT’S REQUIREMENTS FOR
EXPOSURE TO RADIO WAVES.
The SO-03F Series mobile phones have
been designed to comply with
applicable safety requirements for
exposure to radio waves. Your wireless
phone is a radio transmitter and receiver.
It is designed to not exceed the limits* of
exposure to radio frequency (RF) energy
set by governmental authorities. These
limits establish permitted levels of RF
energy for the general population. The
guidelines are based on standards that
were developed by international
scientific organizations through periodic
and thorough evaluation of scientific
studies.
The standards include a safety margin
designed to assure the safety of all
individuals, regardless of age and health.
The radio wave exposure guidelines
employ a unit of measurement known as
the Specific Absorption Rate (SAR).Tests
for SAR are conducted using
standardized methods with the phone
transmitting at its highest certified
power level in all used frequency bands.
While there may be differences between
the SAR levels of various phone models,
they are all designed to meet the
relevant guidelines for exposure to radio
waves. For more information on SAR,
please refer to the important
information chapter in the User Guide.
The highest SAR value as reported to the
authorities for this phone model when
tested for use by the ear is 0.52 W/kg*,
and when worn on the body is 0.59 W/
kg*. For body-worn operation, the
phone has been tested when positioned
a minimum of 15 mm from the body
without any metal parts in the vicinity of
the phone or when properly used with
an appropriate accessory and worn on
the body.
For devices which include “WiFi
hotspot” functionality, SAR
measurements for the device operating
in WiFi hotspot mode were taken using a
separation distance of 10 mm.
Use of third-party accessories may result
in different SAR levels than those
reported.
Radio Wave Exposure and
Specific Absorption Rate
(SAR) Information
0.45W
/
** Before a phone model is available for
sale to the public in the US, it must be
tested and certified by the Federal
Communications Commission (FCC) that
it does not exceed the limit established
by the government-adopted
requirement for safe exposure*. The
tests are performed in positions and
locations (i.e., by the ear and worn on
the body) as required by the FCC for
each model. The FCC has granted an
Equipment Authorization for this phone
model with all reported SAR levels
evaluated as in compliance with the FCC
RF exposure guidelines. While there may
be differences between the SAR levels of
various phones, all mobile phones
granted an FCC equipment
authorization meet the government
requirement for safe exposure. SAR
information on this phone model is on
file at the FCC and can be found under
the Display Grant section of http://
transition.fcc.gov/oet/ea/fccid/ after
searching on FCCID PY7PM-0741.
Additional information on SAR can be
found on the Mobile Manufacturers Forum
EMF website at http://
www.emfexplained.info/.
* In the United States, the SAR limit for mobile
phones used by the public is 1.6 watts/
kilogram (W/kg) averaged over one gram of
tissue. The standard incorporates a margin of
safety to give additional protection for the
public and to account for any variations in
measurements.
** This paragraph is only applicable to
authorities and customers in the United
States.
This device complies with Part
15 of the FCC rules. Operation
is subject to the following two
conditions:
Any change or modification not
expressly approved by Sony Mobile
Communications AB may void the user's
authority to operate the equipment.
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and if not
installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
･Reorient or relocate the receiving
antenna.
･Increase the separation between the
equipment and receiver.
･Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
･Consult the dealer or an experienced
radio/TV technician for help.
FCC Statement for the USA
(1) This device may not cause harmful
interference.
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
Caution:
Your device can only connect to an FCC
approved access point when using 5
GHz WLAN for indoor and outdoor
operation. This is because operation in
the 5.15 GHz tp 5.25 GHz frequency
band is only permitted for indoor use.
We, Sony Mobile Communications AB
of Nya Vattentornet SE-221 88 Lund,
Sweden declare under our sole
responsibility that our product
Sony type PM-0741-BV and in
combination with our accessories, to
which this declaration relates is in
conformity with the appropriate
standards EN 301 511:V9.0.2, EN 301
489-3:V1.4.1, EN 301 489-7:V1.3.1, EN
301 489-17:V2.2.1, EN 301 489-24:V1.5.1,
EN 300 328:V1.7.1, EN 301 908-1:V5.2.1,
EN 301 908-2:V5.2.1, EN 301 908-
13:V5.2.1, EN 300 440-2:V1.4.1, EN 301
893:V1.7.1, EN 302 291-2:V1.1.1, EN 62
209-1:2006, EN 62 209-2:2010 and EN 60
950-
1:2006+A11:2009+A1:2010+A12:2011
following the provisions of Radio
Equipment and Telecommunication
Terminal Equipment Directive 1999/5/
EC
Lund, April 2014
Pär Thuresson
Quality Officer, SVP, Quality & Customer
Services
Declaration of Conformity
for SO-03F

Navigation menu