Sony Cdx M9905X Operating Instructions XT XM1

Sony-Cdx-F5005X-Operating-Instructions-598954 sony-cdx-f5005x-operating-instructions-598954

Sony-Cdx-F5710-Operating-Instructions-598979 sony-cdx-f5710-operating-instructions-598979

Sony-Cdx-Mp40-Operating-Instructions-599250 sony-cdx-mp40-operating-instructions-599250

Sony-Mex-5Di-Operating-Instructions-599366 sony-mex-5di-operating-instructions-599366

Sony-Cdx-R5715X-Operating-Instructions-599264 sony-cdx-r5715x-operating-instructions-599264

: Sony Sony-Cdx-M9905X-Operating-Instructions-599241 sony-cdx-m9905x-operating-instructions-599241 sony pdf

Open the PDF directly: View PDF .
Page Count: 2

Operating Instructions

XM Satellite

Radio Receiver

XT-XM1

Sony Corporation © 2002 Printed in Japan

Owner’s Record

The model number is located on the bottom and serial number also on the bottom.

Record the serial number in the space provide below. Refer to these numbers

whenever you call upon your Sony dealer regarding this product.

Model No. XT-XM1

Serial No.

XM Radio ID

You need to subscribe for XMTM Satellite Radio Service to listen to the radio

broadcast.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

— Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual

could void your authority to operate this equipment.

3-243-168-11 (1)

If you have any questions or problem concerning this product, consult your nearest Sony

dealer.

If you have any questions or problem concerning the XM Satellite radio service including the

broadcast, consult XM.

The XM Radio ID (XM-ID) is required when consulting XM. It is located on the bottom of the

main unit, and you can also check it in the display of this unit (see “Displaying the XM Radio

ID”).

Welcome!

Thank you for purchasing the Sony XM Satellite

Radio Receiver. The receiver allows you to:

•Receive XM Satellite Radio programming (with

subscription) by connecting a Sony master

unit* compatible with the Sony BUS system.

•Connect and use an optional CD or MD

changer.

•Receive up to 100 channels of XM

programming.

•Display channel name, artist name, and song

title for most XM channels.

•Store up to 20 favorite XM channels.

•Search XM channels by category.

*Some master units may not be connected to this

receiver. (For details, please consult your nearest

Sony dealer.)

Introducing XMTM Satellite Radio

There’s a world beyond AM and FM. XM

Satellite Radio. Up to 100 channels. Coast-to-

Coast Coverage. Digital quality sound. With

many commercial-free music channels. Plus, the

best sports, comedy, talk, news and

entertainment, including USA Today, Discovery

Radio, NASCAR, Sesame Workshop, CNNfn

and CNN/SI. Questions? Visit

www.xmradio.com. The future is waiting.

How to Subscribe

Listeners can subscribe by visiting XM on the

Web at www.xmradio.com or by calling XM’s

Listener Care at (800)852-9696. Customers

should have their Radio ID ready; it is located on

the bottom of the main unit, and you can also

check it in the display of this unit (see

“Displaying the XM Radio ID”).

Technology. It is prohibited to copy, decompile,

disassemble, reverse engineer or manipulate any

technology incorporated in receivers compatible

with the XM Satellite Radio system.

Furthermore, the AMBE® voice compression

software included in this product is protected by

intellectual property rights including patent

rights, copyrights, and trade secrets of Digital

Voice Systems, Inc. The user of this or any other

software contained in an XM Radio is explicitly

prohibited from attempting to copy, decompile,

reverse engineer, or disassemble the object code,

or in any other way convert the object code into

human-readableform. The software is licensed

solely for use within this product.

Getting Started

Resetting the master unit

Before operating the XM receiver for the first

time, reset the master unit. If the unit is not reset

in this manner, it may not function properly. For

details on how to reset it, refer to the operating

instructions of the master unit.

Caution

For the following master units, press the Repeat

(REP) button of the master unit for two seconds

after turning the XM on and select “setup 2.”

Without this procedure, the master unit will not

display tuning-in information from the receiver

correctly. Except for the following master units,

“setup 1” is selected in the factory settings.

CDX-C8050X

CDX-C800REC*

CDX-M750

CDX-M650

CDX-M610

CDX-M600

MDX-C8500X

XR-M550

*You may observe flickering in parts of the display

while performing operations. This is not

malfunction.

Note

Resetting the master unit will erase the clock setting

and some stored contents of the master unit.

Using category search to locate

channels

Each XM channel is associated with a category

that describes the type of music or programming

that is played on the channel. Examples of

categories include “rock,” “jazz,” “news,” and so

on. Users unfamiliar with XM’s programming

may use the radio’s search-by-category function

to select channels.

1Press the Repeat (REP) button to enter

category search mode.

The category of the current channel is

displayed. With some master units, the

Repeat button is only equipped on the remote

control.

2Press the Disc/Preset buttons

repeatedly until you find the desired

category.

3Press the Seek buttons repeatedly

until you find the desired channel in

that category.

The display shows “CAT SRCH” to indicate

that the radio is in category search mode.

While in this mode, you will only be able to

tune to channels in the selected category. You

may use the Disc/Preset buttons to choose

other categories.

4To exit from category search mode

and return to the normal mode, press

the Repeat (REP) button.

The radio automatically returns to the normal

mode if there no key is pressed within 5

seconds.

Storing favorite channels

You can preset up to 20 channels.

1Tune in a channel that you want to

store.

2Press the Shuffle (SHUF) button.

The radio will show a list of presets, starting

with preset number 1. The preset number will

be shown if a channel has already been stored

into the preset. With some master units, the

Shuffle button is only equipped on the remote

control.

3Press the Disc/Preset button to select

a preset number.

With some master units, the Disc/Preset

button is only equipped on the remote

control.

4Press the Disc/Preset + (Disc +) button

for 2 seconds.

The display shows “MEMORY” if the radio

successfully stores the channel into the preset.

The display shows “FAILURE” if the radio

fails to store the channel into the preset.

The radio automatically returns to the normal

mode if there no key is pressed within 5

seconds.

Receiving a stored channel

•Press either Disc/Preset button to

select the preset channel you want to

listen to.

•Press the Shuffle (SHUF) button.

Press the Disc/Preset + (DISC +) button

to select the preset channel and then

press the SEEK + or SEEK – button to

start.

Displaying the XM Radio ID

1During XM Satellite Radio reception,

press the Seek button to select

“CHANNEL 1.”

2Press the “Seek – (down)” button.

“RADIO ID” is indicated for 2 seconds and

the XM Radio ID number is indicated for 10

seconds. These indications will be displayed

alternately.

To cancel the XM Radio ID display, press the

Seek button to select a channel.

Basic Operations

Listening to a program

The XM receiver is controlled by the master unit.

Button locations vary with different master unit

models. Please refer to the master unit

instruction manuals.

1To select XM:

a. Press the Source button until “XM” is

displayed.

-or-

b. Press the Source button until “MD” is

displayed, then press the Mode button to

select XM. For master units which can

control more than one MD changer, press

the Mode button repeatedly (the display

will show “MD1,” “MD2,” etc.) until the

receiver is found.

2Press either Seek button to select the

desired channel.

Pressing and holding the Seek button will

quickly step through the channels.

Note

“LOADING” is indicated while the receiver is reading

the information.

Display items

The XM Satellite Radio information (Channel

Name, Channel Number, Artist Name/Program

Name and Song Title) is available on the display.

Press the Display (DSPL) button.

Each time you press the Display (DSPL)

button, the item changes as follows:

Channel Name t Channel Number t

Artist Name/Program Name t Song Title t

For MEX-5DI, press the ENTER button of the

remote control to change the display item.

Notes

•While Artist Name/Program Name or Song Title is

displayed, if you select a channel, Channel Name

will be displayed for 2 to 3 seconds and then return

to the previous display.

•If there is no information about Artist Name/

Program Name or Song Title, “- - - -” will be

displayed.

•During XM Satellite Radio reception, Spectrum

Analyzer, Dual Information, Motion Display

function of the master unit cannot be operated.

• The display indicates up to 8 characters.

The characters on the display cannot be scrolled

even when the Auto Scroll function of the master

unit is set to on.

•You cannot display the clock during XM Satellite

Radio reception on a master unit whose clock

display is shown by pressing the Display (DSPL)

button.

Additional

Information

Specifications

Frequency 2332.5 – 2345.0 MHz

Power requirements 12 V DC car battery

(negative ground)

Outputs BUS control output

Audio output

Inputs Antenna input (Satellite,

Terrestrial)

BUS control input

Audio input

Dimensions 224 × 37.8 × 160 mm

(8 7/8 × 1 1/2 × 6 3/8 in.)

(w/h/d)

Mass Approx. 1.0 kg

(2 lb. 4 oz.)

Supplied accessories Parts for installation and

connection (1 set)

Design and specifications are subject to change

without notice.

Troubleshooting

Should any problem persist after you have made

the following checks, consult your nearest Sony

dealer. Consult XM if you have any questions or

problem concerning the broadcast service of the

XM Satellite radio.

The information on the display cannot be

changed during XM Satellite Radio reception.

•Refer to “Caution” in “Getting Started.”

No sound.

•Adjust the volume control of the master unit.

•Cancel the attenuate function of the master

unit.

•The connecting cords are not connected

properly.

The sound is hampered by noises.

Locate codes and cables such as an antenna

code, a BUS cable, an RCA pin code, or a

power code so as they do not interfere each

other.

The channels cannot be received.

Check the connection of the receiver and the

antenna.

Advisory Message

When a problem occurs with the receiver, an

error message will be indicated on the display of

the master unit.

ANTENNA

The antenna is not connected properly.

tCheck the connection of the receiver and

the antenna.

UPDATING

You have not subscribed to XM, or the channel

is not authorized.

t You need to subscribe to XM.

NO SIGNL

XM signal is too weak.

t Move to another area where your system

can receive the signal.

OFF AIR

The channel is not broadcasted now.

t Select another channel.

LOADING

The receiver is reading the channel

information

tWait until the receiver completes receiving

the information.

“– – – –” or “CH – – –”

•The channel to be tuned-in is void due to the

change by the broadcast service, or the

receiving condition is not good.

•There is no text information or time

information in the channel. This is not an

error.

Installation

Parts list

The numbers in the list are keyed to those in the instructions.

Precautions

•Choose the mounting location carefully, observing the following:

—The unit is not subject to temperatures exceeding 55°C (131°F) (such as in a car parked in direct

sunlight).

— The unit is not subject to direct sunlight.

—The unit is not near heat sources (such as heaters).

—The unit is not exposed to rain or moisture.

—The unit is not exposed to excessive dust or dirt.

—The unit is not subject to excessive vibration.

—The fuel tank should not be damaged by the tapping screws.

—There should be no wire harnesses or pipes under the place where you are going to install the

unit.

—The spare tire, tools or other equipment in or under the trunk should not be interfered with or

damaged by the screws or the unit itself.

•Be sure to use only the supplied mounting hardware for a safe and secure installation.

•Use only the supplied screws.

Installing the unit

•Mount the unit either inside the trunk or under a seat.

•Choose the mounting location carefully so the unit will not interfere with the normal movements of

the driver and it will not be exposed to direct sunlight or hot air from the heater.

•Do not install the unit under the floor carpet, where the heat dissipation from the unit will be

considerably impaired.

12 3 4

5.5m 5.5m5.5m

First, place the unit where you plan to install it, and mark the positions of the four screw holes on

the mounting surface.

Notes

• Use only the supplied screws.

• Be sure not to damage the fuel tank or brake line with the tapping screws.

Fuse replacement

If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after

replacement, there may be an internal malfunction.

Warning

Use a fuse with the specified amperage rating.

Use of a higher amperage fuse may cause serious damage.

Connection

Connection example

ø4 × 14 mm

× 4

Screw hole:

ø3.3 mm (5/32 in.)

Cautions

•This unit is designed for negative ground 12 V DC operation only.

•Before making connections, turn the car ignition off to avoid short circuits.

• Connect the yellow power input cord only after all other cords have been connected.

• Run all ground leads to a common ground point.

Connection diagram

XM Antenna*Sony BUS Compatible

Car Audio*

XT-XM1

CD/MD changer**not supplied

11

POWER

SONY BUS CONTROL

OUT IN L R L R

OUT IN

AUDIO

TER SAT

ANTENNA

Yellow

To a +12 V power terminal which

is energized at all times

Be sure to connect the black ground

lead to it first.

Fuse (3 A)

Black

To a metal point on the car

First connect the black ground lead,

then connect the yellow power input

leads.

CD/MD changer

(not supplied)

Sony BUS Compatible

Car Audio

(not supplied)

4

3

XM antenna

(not supplied)

OUT

OUT

IN

IN

Green Yellow

Connect as the connector

hook facing down

Connect with BUS cable to

the XM Satellite receiver,

aligning the v marks.

RCA pin cord

(not supplied)

BUS cable

(not supplied)

2

Note

When you use an optional BUS cable, note

that a BUS cable with an 8-pin plug (L-type)

cannot be used because of its shape.

(Curry)