Sony Cfd F10 Users Manual F10/F10L
sonycfdcfdf10 189f0222-d778-4d44-d12b-e4323f7b4b20 Sony MP3 Player CFD-F10 User Guide |
2015-01-24
: Sony Sony-Cfd-F10-Users-Manual-294916 sony-cfd-f10-users-manual-294916 sony pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Precautions On safety • As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. • Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further. • Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this player. Attempting to do so may damage the player. Do not use such discs. Cleaning the cabinet • Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. Notes on cassettes • Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. On placement • Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place the player on an inclined or unstable place. • Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. • If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. • Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. On operation • If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. • If the player has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette. General The power does not come on. Side A Tab for side A Tab for side B • The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback. Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. On power sources • For AC operation, check that the player’s operating voltage is identical with your local power supply (see “Specifications”) and use the supplied mains lead; do not use any other type. • The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. • For battery operation, use six R20 (size D) batteries. • When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. • The nameplate indicating operating voltage, power consumption, etc. is located at the bottom. Troubleshooting • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak. • You cannot turn on the player with the remote when you operate the player on batteries. The power is not on, and “bAttErY” and “Error” are displayed alternately. • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak. There is no audio. • Adjust the volume. • Unplug the headphones when listening through speakers. Tape Player Specifications The tape does not move when you press an operation button. CD player section • Close the cassette compartment securely. The z button does not function or the tape does not play or record. • Make sure the safety tab on the cassette is in place. Poor or distorted playback, recording or erasing quality. • Clean the heads, pinch roller and capstan with a cleaning swab slightly moistened with cleaning fluid or alcohol. • Replace all the batteries with new ones if they are weak. • TYPE II (high position) or TYPE IV (metal) tape is being used. Use TYPE I (normal) tape only. • Demagnetize the heads using a commercially available tape head demagnetizer. Noise is heard. • Someone is using a portable telephone or other equipment that emits radio waves near the player. tMove the portable telephone, etc., away from the player. Record/playback head • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. • Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. • Do not stick paper or sticker on the CD, nor scratch the surface of the CD. • After playing, store the CD in its case. If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error. About CD-Rs/CD-RWs This player can play CD-Rs/CD-RWs recorded in the CD-DA format*, but playback capability may vary depending on the quality of the disc and the condition of the recording device. * CD-DA is the abbreviation for Compact Disc Digital Audio. It is a recording standard used for Audio CDs. Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. • Place the CD with the label surface up. • Clean the CD. • Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. • The CD-R/CD-RW was not finalized. Finalize the CD-R/CD-RW with the recording device. • There is a problem with the quality of the CDR/CD-RW, recording device or application software. • The CD-R/CD-RW is blank. • Replace all the batteries with new ones if they are weak. Radio Reception is poor. The audio is weak or has poor quality. • Replace all the batteries with new ones if they are weak. • Move the player away from the TV. The picture of your TV becomes unstable. • If you are listening to an FM programme near the TV with an indoor aerial, move the player away from the TV. CD Radio CassetteCorder Operating Instructions To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the appliance. Notice for customers in the United Kingdom A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience. CFD-F10 Erase head Pinch roller FM 87.5 - 108 MHz AM 531 - 1 611 kHz (9 kHz step) 530 - 1 710 kHz (10 kHz step) Should the fuse in the plug supplied need to be replaced, same rating fuse approved by ASTA or BSI to BS 1362, (i.e. marked with mark) must be used. CFD-F10L Lens FM 87.5 - 108 MHz MW 531 - 1 611 kHz (9 kHz step) 530 - 1 610 kHz (10 kHz step) LW 153 - 279 kHz IF FM: 10.7 MHz AM/MW/LW: 450 kHz Aerials FM: Telescopic aerials AM/MW/LW: Built-in ferrite bar aerials Remote The remote does not function. • Replace all the batteries in the remote with new ones if they are weak. • Make sure that you are pointing the remote at the remote sensor on the player. • Remove any obstacles in the path of the remote and the player. • Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. • Move closer to the player when using the remote. After trying the above remedies, if you still have problems, unplug the mains lead and remove all the batteries. After all the indications in the display disappear, plug the mains lead and insert the batteries again. If the problem persists, please consult your nearest Sony dealer. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. Sony MDR headphone series To prevent fire or shock hazard, do not expose the player to rain or moisture. Frequency range • Reorient the aerial to improve FM reception. • Reorient the player itself to improve AM or MW/LW reception. Optional accessories WARNING Radio section The sound drops out. • Reduce the volume. • Clean the CD, or replace it if the CD is badly damaged. • Place the player in a location free from vibration. • Clean the lens with a commercially available blower. • The sound may drop out or noise may be heard when using poor quality CD-Rs/CDRWs or if there is a problem with the recording device or application software. Design and specifications are subject to change without notice. English Capstan CD Player The CD does not play or “no dISC” lights in the display even when a CD is in place. System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20 000 Hz +1/–2 dB Wow and flutter Below measurable limit Dimensions Approx. 515 × 201 × 287 mm (w/h/d) (20 3⁄8 × 8 × 11 3⁄8 inches) (incl. projecting parts) Mass Approx. 5.1 kg (11 lb. 4 oz) (incl. batteries) Supplied accessory Mains lead (1) Remote control (1) Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 110 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 80 - 13 000 Hz CFD-F10 CFD-F10L FM recording Sony R20P: approx. 3.5 h Sony alkaline LR20: approx. 10 h Tape playback Sony R20P: approx. 1.5 h Sony alkaline LR20: approx. 5 h CD playback Sony R20P: approx. 1 h Sony alkaline LR20: approx. 4 h If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station. ©2004 Sony Corporation 3-264-046-12 (1) Power Sources General Speaker Full range: 10 cm dia., 6 Ω, cone type (2) Tweeter: 2 cm dia. (2) Passive Radiator: 10 cm dia. (1) Input LINE IN jack (stereo minijack) (CFD-F10L only): Minimum input level 330 mV Outputs Headphones jack (stereo minijack): For 16 - 68 Ω impedance headphones OPTICAL DIGITAL OUT (CD) (Optical output connector) (CFD-F10L only): Wavelength: 630 - 690 nm Maximum Power output 8W Power requirements For CD radio cassette-corder: Argentine model: 220 - 230 V AC, 50 Hz Other models: 230 V AC, 50 Hz 9 V DC, 6 R20 (size D) batteries For remote control: 3 V DC, 2 R03 (size AAA) batteries Power consumption AC 25 W Battery life For CD radio cassette-corder: or C B A 1 to AC IN Connect the mains lead A or insert six R20 (size D) batteries (not supplied) into the battery compartment B . Notes • Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player. • To use the player on batteries, disconnect the mains lead from the player. • When you operate the player on batteries, you cannot turn on the player using the remote. Preparing the remote C Insert two R03 (size AAA) batteries (not supplied). Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. 2 to the mains Playing a CD Location of controls Remote Control Loading a CD Inserting a cassette 1 SLEEP With the side you want to play facing upward OPERATE (POWER) FUNCTION Number buttons MODE BAND MEGA BASS VOLUME +*, – TUNE –, + m,M PRESET –, + ., > N u* Z PUSH OPEN/CLOSE CD x X MEGA Xpand .,> i MEGA BASS x TAPE Press Z PUSH OPEN/CLOSE to close the CD compartment. N on the remote). Press u (N The player plays all the tracks once. go to the next track go back to the previous track remove the CD locate a point while listening to the sound locate a point while observing the display locate a specific track directly* Press x u (X X on the remote) Press the button again to resume play after pause. > . Z PUSH OPEN/CLOSE M (forward) or m (backward) while playing until you find the point (> or . on the remote) M (forward) or m (backward) in pause until you find the point (> or . on the remote) a number button of the track on the remote * You cannot locate a specific track if “SHUF” or “PGM” is lit in the display. Turn off the indication by pressing x. Tip To locate a track numbered over 10, press >10 first, then the corresponding number buttons on the remote. Example:To play track number 23, press >10 first, then 2 and 3. Using the display To check the total track number and playing time MODE *The button has a tactile dot. OPERATE (POWER) RADIO BAND AUTO PRESET SLEEP Display DSPL/ENT/ MEM OPR/BATT Remote Sensor LINE IN (CFD-F10L only) Press DSPL/ENT/MEM repeatedly while playing a CD. The display changes as follows: t the current track number and playing time r the current track number and the remaining time on the current track* r the number of tracks left and remaining time on the CD Display D Total track number Total playing time E Programmed track Press DSPL/ENT/MEM in stop mode (see fig. D). To check the remaining time OPTICAL DIGITAL OUT (CD) (CFD-F10L only) Playing order * For a track whose number is more than 20, the remaining time appears as “- -:- -” in the display. Selecting the play mode To turn on/off the power CFD-F10L: Press OPERATE. CFD-F10: Press POWER. To adjust the volume Press VOLUME +, – (VOL +, – on the remote). To listen through headphones Connect the headphones to the i (headphones) jack. Falling asleep to music 1 Play the music source you want. 2 Press SLEEP to display “SLEEP.” 3 Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: “60” t “90” t “120” t “OFF” t “10” t “20” t “30” To cancel the sleep function Press OPERATE (or POWER) to turn off the power. Adjusting the sound emphasis To reinforce the bass sound Press MEGA BASS. “MEGA BASS” appears in the display. To return to normal sound, press the button again. To get the MEGA Xpand effect Press MEGA Xpand. “MEGA Xpand” appears in the display. You can get the effect of expansion of the sound field. To return to normal sound, press the button again. Note 1 Load a CD in the CD compartment. VOL +*, – TUNE +, – MEGA Xpand LINE (CFD-F10L only) Press CD (direct power-on). (On the remote, press OPERATE (or POWER) and then press FUNCTION repeatedly until “Cd” appears in the display.) To stop playback pause playback With the labeled side up * 2 3 4 Listening to the radio Press MODE until “REP 1” “REP ALL” “SHUF” “SHUF REP” “PGM” “PGM REP” appears in the display. Then proceed as follows: To repeat a single track repeat all tracks shuffle play repeat tracks in random order programme play Select “REP 1” Then do this Press . or > to select the track that you want to repeat, then press u. “REP ALL” Press u. “SHUF” Press u. “SHUF REP” Press u. Press RADIO BAND•AUTO PRESET until the band you want appears in the display (direct power-on). Each time you press the button, the indication changes as follows: CFD-F10: “FM” t “AM” CFD-F10L: “FM” t “MW” t “LW” 1 2 Press xZ to open the tape compartment and insert a recorded tape. Close the compartment. Use TYPE I (normal) tape only. Hold down TUNE + or – until the frequency digits begin to change in the display. 3 Press N. The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step. “PGM REP” Press . or > then press DSPL/ENT/MEM for the tracks you want to programme in the order you want up to 20 tracks (see fig. E). Then press u. Press . or > then press DSPL/ENT/MEM for the tracks you want to programme in the order you want up to 20 tracks. Then Press u. Changing the AM/MW tuning interval The AM/MW tuning interval is preset to 9 kHz at the factory. If you need to change the AM/MW tuning interval, do the following: 1 While keeping the RADIO BAND•AUTO PRESET button and TAPE button pressed, disconnect the mains lead from the mains. 2 While keeping the RADIO BAND•AUTO PRESET button and TAPE button pressed, reconnect the mains lead to the mains. The tuning interval is changed and “AM 9” “MW 9” or “AM 10” “MW 10” appears in the display for 2 seconds. After changing the tuning interval, you need to reset your preset radio stations. Presetting radio stations You can store radio stations into the player’s memory. You can preset up to 30 radio stations (CFD-F10), 20 for FM and 10 for AM in any order, or 40 radio stations (CFD-F10L), 20 for FM, 10 for MW and 10 for LW in any order. 1 2 Press RADIO BAND•AUTO PRESET to select the band. 3 Press DSPL/ENT/MEM. The stations are stored in memory from the lower frequencies to the higher ones. Hold down RADIO BAND•AUTO PRESET for 2 seconds until “AUTO” flashes in the display. If a station cannot be preset automatically You need to preset a station with a weak signal manually. 1 Press RADIO BAND•AUTO PRESET to select the band. 2 Tune in a station you want. 3 Hold down DSPL/ENT/MEM for 2 seconds until the preset number flashes in the display. 4 Press PRESET + or – until the preset number you want for the station flashes in the display. 5 Press DSPL/ENT/MEM. The new station replaces the old one. On the remote 1 Press BAND until the band you want appears in the display. 2 Tune in a station you want. 3 Hold down the number buttons that you want to preset the new station on for about 2 seconds. To select the preset number over 10, press >10 first, then the corresponding number buttons. You need to hold down the last number button to enter for about 2 seconds. (Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.) The preset radio stations remain in memory even if you unplug the mains lead or remove the batteries. Playing preset radio stations 1 2 Press RADIO BAND•AUTO PRESET to select the band. Press PRESET + or – to tune in the stored station. On the remote When you’ve selected “PGM” or “PGM REP”, press the number buttons for the track you want up to 20 tracks, then press N. 1 Press BAND. 2 Press the number buttons to tune in the stored station. To tune in a preset station over 10, press >10 first, then corresponding number buttons. (Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.) Press MODE repeatedly until the selected mode disappears from the display. To check the programmed track and playing order in the display To check the order of tracks before play, press DSPL/ENT/MEM. Every time you press the button, the track number appears in the programmed order. To change the current programme Press x once if the CD is stopped and twice if the CD is playing. The current programme will be erased. Then create a new programme following the programming procedure. Tips • You can play the same programme again, since the programme is saved until you open the CD compartment. • You can record your own programme. After you’ve created the programme, insert a blank tape and press z to start recording. To stop playback fast-forward or rewind the tape pause playback Press xZ M or m X Press the button again to resume play after pause. xZ Connecting optional components (CFD-F10L only) You can record a CD on a MiniDisc and enjoy the sound from other components, such as portable MD, CD player and TV, VCR through the speakers of this player. Be sure to turn off the power of each component before making connections. For details, refer to the instructions of the component to be connected. Recording a CD on a MiniDisc recorder or DAT recorder 1 Recording 1 Press xZ to open the tape compartment and insert a blank tape. Use TYPE I (normal) tape only. 2 Select the programme source you want to record. The type of the jack of the component to be connected Optical miniplug (MiniDisc recorder, etc.) Square-shaped optical connector (MiniDisc recorder, DAT recorder, etc.) To record from the CD player Press CD and insert a CD (See “Playing a CD”). To record from the radio Press RADIO BAND•AUTO PRESET and tune in the station you want (See “Listening to the radio”). 3 Press z to start recording. (N is depressed automatically.) To stop recording pause recording Press xZ X Press the button again to resume recording. 2 3 4 Model number of the connecting cable POC-15AB POC-15A Turn on the power of this player and the connected component. Make the connected component ready for recording. Press u to start playing a CD. Listening to the sound from the connected component 1 Tips • Adjusting the volume or the audio emphasis will not affect the recording level. • CFD-F10L only: If the AM or MW/LW programme makes a whistling sound after you've pressed z in step 3, press MODE to select the position of ISS (Interference Suppress Switch) that most decreases the noise. • For the best results, use the AC power as a power source for recording. • To erase a recording, proceed as follows: 1 Insert a tape with the recording you want to erase. 2 Press TAPE. 3 Press z. Connect the OPTICAL DIGITAL OUT (CD) jack of this player with the digital input jack of MiniDisc and DAT using the digital connecting cable* (not supplied). * Select a connecting cable depending on the type of the digital input jack of the recorder to be connected. For details, refer to the instruction manual of the component to be connected. The OPTICAL DIGITAL OUT (CD) jack of this player is square-shaped jack. If the FM broadcast is noisy, press MODE repeatedly until “Mono” appears in the display and the radio will play in monaural. On the remote To cancel selected play mode Press TAPE (direct power-on). (On the remote, press OPERATE (or POWER) and then press FUNCTION repeatedly until “TAPE” appears in the display.) eject the cassette Tip Tip “PGM” When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. repeat programmed tracks 2 Playing a tape Connect the LINE IN jack of this player with the line output jack or headphones jack of other component using the audio connecting cable* (not supplied). * For MiniDisc recorder: a cable with a stereo-mini plug on both ends. * For TV, VCR: a cable with a stereo-mini plug on one end and two phono plugs on the other end. 2 3 Press LINE to display “LInE”. Play the optional component connected to the LINE IN jack of the player. Tip You can record the sound from the connected component. Insert a blank tape into the tape compartment, and press z. Note Connect the cords firmly to avoid any malfunction.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Create Date : 2004:05:05 14:27:14Z Modify Date : 2004:05:05 23:28:23+09:00 Page Count : 2 Creation Date : 2004:05:05 14:27:14Z Mod Date : 2004:05:05 23:28:23+09:00 Producer : Acrobat Distiller 5.0.5 for Macintosh Author : Sony Corporation Metadata Date : 2004:05:05 23:28:23+09:00 Title : CFD-F10/F10L Creator : Sony CorporationEXIF Metadata provided by EXIF.tools