Sony Mhc Gx555 Users Manual GX555/GX355/GX255/RG575S/RG475S/RG470/RG270/RG170

MHC-GX355 Operating Instructions MHC-GX255_GX355_GX555_RG575S_RG475S_RG470_RG270_RG170

MHC-GX555 Operating Instructions MHC-GX255_GX355_GX555_RG575S_RG475S_RG470_RG270_RG170

GX355 MHCGX355-555revision

GX255 docget

RDRGX255 to the manual 75455c47-b0e4-4260-981d-aa720147bac7

: Sony Sony-Mhc-Gx555-Users-Manual-298080 sony-mhc-gx555-users-manual-298080 sony pdf

Open the PDF directly: View PDF .
Page Count: 44

Download
Open PDF In Browser	View PDF

2-580-011-12(1)

Mini HI-FI
Component
System
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the serial number
in the space provided below. Refer to them whenever you call upon your Sony dealer
regarding this product.
Model No. ______________
Serial No. ______________

MHC-GX555/GX355/GX255
MHC-RG575S/RG475S/RG470/
RG270/RG170
©2005 Sony Corporation

WARNING

WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To prevent fire, do not cover the ventilation of the
apparatus with news papers, table-cloths, curtains, etc.
And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical waste.

NOTICE FOR THE CUSTOMERS IN THE
U.S.A.

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
CAUTION

You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
Note to CATV system installer:

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
NOTICE FOR THE CUSTOMERS IN CANADA

This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION

The use of optical instruments with this product will
increase eye hazard.

2GB

CAUTION

The use of optical instruments with this product will
increase eye hazard.
Except for European and Russian models

ENERGY STAR® is a U.S.
registered mark. As an ENERGY
STAR® partner, Sony Corporation
has determined that this product
meets the ENERGY STAR®
guidelines for energy efficiency.

Table of Contents
How to use this manual........................... 4
Playable discs.......................................... 4

Getting Started
Hooking up the system............................ 6
Setting the clock...................................... 9

CD/MP3 – Play
Loading a disc ....................................... 10
Playing a disc ........................................ 10
— Normal Play/Shuffle Play
Playing repeatedly................................. 12
— Repeat Play
Creating your own program .................. 13
— Program Play

Tuner
Presetting radio stations ........................ 14
Listening to the radio ............................ 15
— Preset Tuning
— Manual Tuning
Using the Radio Data System (RDS).... 16
(European model only)

Tape – Play
Loading a tape....................................... 17
Playing a tape ........................................ 17

Tape – Recording
Recording your favorite CD tracks on a
tape.................................................. 18
— CD-TAPE Synchro Recording
Recording on a tape manually............... 18
— Manual Recording

Sound Adjustment
Adjusting the sound .............................. 19
Using the sub woofer............................ 19
(MHC-GX555/RG575S/RG475S
only)
Selecting the sound effect..................... 19
Adjusting the graphic equalizer and
storing............................................. 20
Selecting the surround effect ................ 20
Singing along: Karaoke ........................ 21
(Latin American model only)

Timer
Falling asleep to music ......................... 22
— Sleep Timer
Waking up to music.............................. 22
— Play Timer
Timer recording radio programs........... 23
— Rec Timer

Display
Turning off the display ......................... 24
— Power Saving Mode
Viewing information about the disc in the
display ............................................ 25
Changing the Power illuminator........... 26
Viewing the tuner information in the
display ............................................ 26

Optional Components
Hooking up optional components......... 27

Troubleshooting
Problems and remedies......................... 28
Messages............................................... 31

Additional Information
Precautions............................................ 32
Specifications........................................ 34
List of button locations and reference
pages............................................... 40

3GB

How to use this manual
This manual mainly explains operations using
the remote, but the same operations can also be
performed using the buttons on the unit having
the same or similar names.

Playable discs
You can play back the following discs on this
system. Other discs cannot be played back.

List of playable discs
Format of discs

Disc logo

Audio CDs

Discs that this system cannot
play
• CD-ROMs
• CD-Rs/CD-RWs other than those recorded in
the following formats:
– music CD format
– MP3 format that conforms to ISO96601)
Level 1/Level 2, Joliet or Multi Session2)
• Discs with non-standard shapes (e.g., heart,
square, star) cannot be played on this unit.
Attempting to do so may damage the unit. Do
not use such discs.
• A disc with paper or stickers on it.
• A disc that has the adhesive, cellophane tape,
or a sticker still left on it.
1)

CD-Gs*
(CD-Graphics)

CD-R/CD-RW
(audio data/MP3
files)

2)

* Playback is possible only on Mexican model.

4GB

ISO9660 Format
The most common international standard for the
logical format of files and folders on a CD-ROM.
There are several specification levels. In Level 1,
file names must be in the 8.3 format (no more than
eight characters in the name, no more than three
characters in the extension “.MP3”) and in capital
letters. Folder names can be no longer than eight
characters. There can be no more than eight nested
folder levels. Level 2 specifications allow file
names and folder names up to 31 characters long.
Each folder can have up to 8 trees.
For Joliet in the expansion format (file and folder
names can have up to 64 characters) make sure of
the contents of the writing software, etc.
Multi Session
This is a recording method that enables adding of
data using the Track-At-Once method.
Conventional CDs begin at a CD control area called
the Lead-in and end at an area called Lead-out. A
Multi Session CD is a CD having multiple sessions,
with each segment from Lead-in to Lead-out
regarded as a single session.
CD-Extra: This format records audio (audio CD
data) on the tracks in session 1 and data on the tracks
in session 2.
Mixed CD: This format records data on the first
track and audio (audio CD data) on the second and
subsequent tracks of a session.

Notes on CD-R and CD-RW
• Some CD-Rs or CD-RWs cannot be played
on this system depending upon the recording
quality or physical condition of the disc, or
the characteristics of the recording device.
Furthermore, the disc will not play if it has not
been correctly finalized. For more
information, see the operating instructions for
the recording device.
• Discs recorded on CD-R/CD-RW drives may
not be played back because of scratches, dirt,
recording condition or the driver’s
characteristics.
• CD-R and CD-RW discs recorded in multisession that have not ended by “closing the
session” are not supported.
• The system may be unable to play MP3
format files that do not have the “.MP3”
extension.
• Attempting to play non-MP3 format files that
have the “.MP3” extension may result in noise
or malfunction.
• With formats other than ISO9660 Level 1 and
2, folder names or file names may not be
displayed correctly.
• The following discs take a longer time to start
playback.
– a disc recorded with complicated tree
structure.
– a disc recorded in Multi Session.
– a disc to which data can be added (nonfinalized disc).

Music discs encoded with
copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.

Cautions when playing a disc
that is recorded in Multi
Session
• If the disc begins with a CD-DA session, it is
recognized as a CD-DA (audio) disc, and
playback continues until an MP3 session is
encountered.
• If the disc begins with an MP3 session, it is
recognized as an MP3 disc, and playback
continues until a CD-DA (audio) session is
encountered.
• The playback range of an MP3 disc is
determined by the tree structure of files
produced by analyzing of the disc.
• A disc with a mixed CD format will be
recognized as a CD-DA (audio) disc.

5GB

Getting Started

Hooking up the system
Perform the following procedures 1 to 6 to hook up your system using the supplied cords and
accessories. A model equipped with a sub woofer is used for illustration purpose.

AM loop antenna

FM lead antenna
Sub woofer*

Front speaker (right)

Front speaker (left)

* MHC-GX555/RG575S/RG475S only

1 Connect the front speakers.

Connect the right and left speaker cords to
the SPEAKER terminals as shown below.
Insert only the stripped portion
Red
R

2 Connect the sub woofer.
(MHC-GX555/RG575S/RG475S only)

Connect the speaker cords to the
SUBWOOFER OUT terminal as shown
below.
Insert only the stripped portion

L

+

Red/Solid (3)

–

Red/Solid (3)
Black/Stripe (#)

Black

Black
Red
Black/Stripe (#)

6GB

3 Connect the FM and AM antennas.

VIDEO
OUT

Plug type A

Getting Started

Set up the AM loop antenna, then connect
it.

4 (Mexican model only)
Connect the video input jack of your TV
to the VIDEO OUT jack with the video
cable (supplied).

AM loop antenna

When using a TV

Turn on the TV and select the video input so that you
can view the pictures from this system.
Note

Mexican model is designed to play back only CD-Gs
recorded in the NTSC color system. If you play a CDG recorded in other color system, the pictures may not
be displayed correctly.
Extend the FM lead antenna horizontally
Plug type B
AM loop antenna

Extend the FM lead
antenna horizontally

5 For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage.

Refer to the print on your system’s
VOLTAGE SELECTOR for available
settings.

North American model:
Connect white side.
Other models:
Connect brown side.

* Saudi Arabian model: 120 – 127 V
Note

To prevent noise pickup, keep the antennas away from
the speaker cords.

continued

7GB

6 Connect the power cord to a wall
outlet.

The demonstration appears in the display.
When you press ?/1, the system turns on
and the demonstration automatically ends.
If the plug does not fit the wall socket,
detach the supplied plug adaptor (only for
models equipped with an adaptor).

Attaching the speaker pads
Attach the supplied speaker pads to the bottom
of the speakers to stabilize the speakers and
prevent them from slipping.
Front speaker (Left (4)/Right (4))
Sub woofer (4)*

Inserting two R6 (size AA)
batteries into the remote

* MHC-GX555/RG575S/RG475S only

When carrying this system
Note

If you do not use the remote for a long period of time,
remove the batteries to avoid possible damage from
battery leakage and corrosion.
Tip

With normal use, the batteries should last for about six
months. When the remote no longer operates the
system, replace both batteries with new ones.

Perform the following procedure to protect
the CD mechanism. Use buttons on the unit
for the operation.

1

Press ?/1 to turn on the system, then
press CD to switch the function to CD.

2

Make sure that all discs are removed
from the system.

3

Hold down CD and then press ?/1 until
“STANDBY” appears.

After a few seconds later, “STANDBY”
disappears and “LOCK” appears.

4

8GB

Unplug the power cord.

To obtain a better bass reproduction, we
recommend you to place the sub woofer on a
solid floor where resonance is unlikely to occur.
Notes

• Always place the sub woofer vertically, keeping it a
few centimeters away from the wall.
• If the sub woofer is placed in the center of a room, the
bass could be extremely weakened. This is due to the
influence of the standing wave of the room. If this
happens, move the sub woofer away from the center
of the room or eliminate the cause of the standing
wave, by placing a bookshelf against the wall, etc.

Setting the clock
Use buttons on the remote for the operation.

1
2
3
4
5
6

Press ?/1 to turn on the system.
Press CLOCK/TIMER SET.
Press . or > repeatedly to set the
hour.

Getting Started

Placing the sub woofer
(MHC-GX555/RG575S/RG475S
only)

Press ENTER.
Press . or > repeatedly to set the
minute.
Press ENTER.

The clock starts working.

To adjust the clock

1
2

Press CLOCK/TIMER SET.

3

Do the same procedures as step 3 to 6
above.

Press . or > repeatedly to select
“CLOCK SET”, then press ENTER.

Notes

• The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
• You cannot set the clock in Power Saving Mode
(page 24).

9GB

CD/MP3 – Play

Loading a disc
Use buttons on the unit for the operation.

1
2

Press Z.
Place a disc with the label side up on
the disc tray.

Playing a disc
— Normal Play/Shuffle Play
This system lets you play audio CDs, CD-Gs*
and discs with MP3 audio tracks.
* CD-Gs (CD-Graphics) can only be played on
Mexican model.
You can enjoy the video images recorded on CD-Gs
by connecting the system to a TV (see step 4 of
“Hooking up the system” (page 6)).

Example: When a disc is loaded
Disc tray number

To insert additional discs, press DISC
SKIP/EX-CHANGE to rotate the disc tray.

3

Press Z again to close the disc tray.

Notes

• Do not use a disc with tape, seals or paste on it as this
may cause malfunction.
• Do not forcibly press the disc tray closed with your
finger, as this may cause malfunction.

10GB

Track number

Disc presence indicator

1

Playing time

Press CD (or FUNCTION repeatedly) to
switch the function to CD.

2

Select

To play

ALL DISCS
(Normal Play)

All discs in the disc tray
continuously.

1DISC
(Normal Play)

The tracks on the disc you
have selected in original
order.

ALBM
(Normal Play)

All MP3 audio tracks in the
album on the disc you have
selected in original order.
When playing a non-MP3
disc, Album Play performs
the same operation as 1DISC
Play.

Other operations
To

Do this

Stop play

Press x.

Pause

Press X. Press again to resume
play.

Select a track

Press . or > repeatedly (or
turn l L on the unit).

Select an album
of MP3

Press ALBUM + or – repeatedly
after step 2.

Find a point in a Keep pressing m or M during
track (except for playback and release it at the
CD-Gs)
desired point.
Select a disc in
stop mode

Press DISC SKIP (or DISC 1 – 3
or DISC SKIP/EX-CHANGE on
the unit).

ALL DISCS
SHUF (Shuffle
Play)

The tracks on all discs in
random order.

Switch to CD
function from
other function

Press DISC 1 – 3 on the unit
(Automatic Source Selection).

1DISC SHUF
(Shuffle Play)

The tracks on the disc you
have selected in random
order.

Exchange other
discs while
playing

Press DISC SKIP/EX-CHANGE
on the unit.

ALBM SHUF
(Shuffle Play)

The MP3 audio tracks in the
album on the disc you have
selected in random order.
When playing a non-MP3
disc, Album Shuffle Play
performs the same operation
as 1DISC SHUF Play.

Remove a disc

Press Z on the unit.

PGM
(Program Play)

The tracks on the disc in the
order you want them to be
played (see “Creating your
own program” on page 13).

CD/MP3 – Play

3

Press PLAY MODE repeatedly in stop
mode until the mode you want appears
in the display.

Press N.

continued

11GB

Notes

• On Mexican model, you cannot perform the
following operations
– selecting the graphic channels of CD-Gs
– displaying CD-G images with fading effects
• On Mexican model, when you play back a CD-G,
some operation may cause image distortion on the
video output.
• You cannot change the play mode during playback.
• Some time may be needed to start playback of discs
recorded in complex configurations such as many
layers.
• When the disc is inserted, the player reads all the
tracks on that disc. If there are many albums or nonMP3 audio tracks on the disc, it may take a long time
for play to begin or for the next MP3 audio track to
start play.
• Do not save unnecessary albums or tracks other than
MP3 ones in the disc to be used for MP3 listening.
We recommend that you do not save other types of
tracks or unnecessary albums on a disc that has MP3
audio tracks.
• An album that does not include an MP3 audio track
is skipped.
• Maximum number of albums: 150 (including root
folder)
• Maximum number of MP3 audio tracks: 255
• The maximum number of MP3 audio tracks and
albums that can be contained on a single disc is 300.
• Playback is possible up to 8 levels.
• MP3 audio tracks are played back in the order that
they are recorded on the disc.
• Depending on the encoding/writing software,
recording device, or the recording media used at the
time an MP3 audio track is recorded, you may
encounter such problems as disabled playback,
sound interruptions, and noise.
• When disc access takes a long time, set “CD POWER
ON” by CD power manage function (page 15).

12GB

Playing repeatedly
— Repeat Play
You can play all the tracks or a single track on a
disc repeatedly.
Press REPEAT repeatedly until “REP” or
“REP1” appears.

REP: For all the tracks on a disc up to five times.
REP1: For a single track only.

To cancel Repeat Play
Press REPEAT repeatedly until both “REP” and
“REP1” disappear.
Notes

• You cannot select “REP” and “ALL DISCS SHUF”
at the same time.
• When you select “REP1”, that track is repeated
endlessly until “REP1” is canceled.

Creating your own
program

6

To program

2
3
4

Press CD (or FUNCTION repeatedly) to
switch the function to CD.
Press PLAY MODE repeatedly in stop
mode until “PGM” appears.
Press DISC SKIP (or DISC 1 – 3 or DISC
SKIP/EX-CHANGE on the unit) to select
a disc.
Press . or > repeatedly (or turn
l L on the unit) until the desired
track number appears.

When programming the MP3 audio tracks,
press ALBUM + or – repeatedly to select
the desired album, then press . or >
repeatedly (or turn l L on the unit)
until the desired track number appears.
Disc tray number

7

3 to 5

Press N.

Program Play starts.

Other operations
To

Do this

Cancel Program
Play

Press PLAY MODE repeatedly
in stop mode until “PGM”
disappears.

Clear a track from
the end

Press CLEAR in stop mode.

CD/MP3 – Play

Other tracks on
other discs

You can make a program of up to 25 steps from
all the discs in the order you want to play them.
You can synchro record the programmed tracks
onto a cassette tape (page 18).

Repeat steps

Other tracks on the 4 and 5
same disc

— Program Play

1

Program additional tracks.

Tips

• The program you made remains after Program Play
finishes. To play the same program again, press CD
(or FUNCTION repeatedly) to switch the function to
CD, then press N. However, the program is cleared
when you open the disc tray.
• “– –.– –” appears when the total CD program time
exceeds 100 minutes, or when you select an MP3
audio track.

Selected track number

Total playing time (including
selected track)

5

Press ENTER.

The track is programmed.
The program step number appears,
followed by the total playing time.

13GB

6
Tuner

Presetting radio stations
You can preset up to 20 FM stations and 10 AM
stations. You can then tune in any of those
stations simply by selecting the corresponding
preset number.

Automatic tuning preset
You can automatically tune in all of the stations
that can be received in your area and then store
the radio frequency of the desired stations.

1
2
3
4

Press TUNER BAND (or FUNCTION
repeatedly) to switch the function to
TUNER.
Press TUNER BAND repeatedly to
select “FM” or “AM”.

7
8

Press + or – (or turn – TUNING + on the
unit) repeatedly to select the desired
preset number.
Press ENTER.
Repeat steps 2 through 7 to store other
stations.

Manual tuning preset
You can manually tune in and store the radio
frequency of the desired stations.

1
2
3
4

Press TUNING MODE repeatedly until
“AUTO” appears in the display.
Press + or – (or turn – TUNING + on the
unit).

5

The frequency changes as the system scans
for a station. Scanning stops automatically
when a station is tuned in. At that time,
“TUNED” and “STEREO” (for an FM
stereo program) appear.

6

Press TUNER BAND (or FUNCTION
repeatedly) to switch the function to
TUNER.
Press TUNER BAND repeatedly to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
“AUTO” and “PRESET” disappear from
the display.
Press + or – (or turn – TUNING + on the
unit) repeatedly to tune in the desired
station.
Press TUNER MEMORY.

A preset number appears.

7
8

Press + or – (or turn – TUNING + on the
unit) repeatedly to select the desired
preset number.
Press ENTER.
Repeat steps 2 through 7 to store other
stations.

Other operations

5

To

Do this

If “TUNED” does not appear and the
scanning does not stop

Tune in a station
with a weak signal

Follow the procedure described
in “Manual tuning preset” .

Set the frequency of the desired radio
station as described in steps 3 through 8 of
“Manual tuning preset” .

Set another station
to the existing
preset number

Start over from step 2. After
step 5, press + or – (or turn –
TUNING + on the unit)
repeatedly to select the preset
number you want to store the
other station.

Press TUNER MEMORY.

A preset number appears.
Preset number

14GB

To change the AM tuning interval
(except for European, Russian
and Saudi Arabian models)

You can listen to a radio station either by
selecting a preset station, or by manually tuning
in the station.

Listening to a preset station
— Preset Tuning

Note

Preset radio stations in the tuner’s memory first
(see “Presetting radio stations” on page 14).

You cannot change the AM tuning interval in Power
Saving Mode (page 24).

1

Tips

• The preset stations are retained for about a day even
if you disconnect the power cord or if a power failure
occurs.
• To improve broadcast reception, adjust the supplied
antennas, or connect a commercially available
external antenna.

To improve tuner reception
When tuner reception is poor, set CD player
power off by CD power manage function.
CD power is factory set to on.
Use buttons on the unit for the operation.

1
2
3

2
3
4

Tuner

The AM tuning interval is factory-preset to
9 kHz (or 10 kHz for some areas). To change the
AM tuning interval, tune in any AM station first,
then turn off the system. While holding
TUNING MODE on the unit, press ?/1 on the
unit. When you change the interval, all the AM
preset stations are erased. To reset the interval,
repeat the same procedure.

Listening to the radio

Press TUNER BAND (or FUNCTION
repeatedly) to switch the function to
TUNER.
Press TUNER BAND repeatedly to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
“PRESET” appears in the display.
Press + or – (or turn – TUNING + on the
unit) repeatedly to select the desired
preset station.
Preset number

Frequency

Press CD to switch the function to CD.
Press ?/1 to turn off the system.
After “STANDBY” stops flashing, press ?/1
while holding x.
“CD POWER OFF” appears.

To set CD power on
Repeat the procedure above and “CD POWER
ON” appears.
Notes

• When “CD POWER OFF” is selected, disc access
time is increased.
• You cannot change the setting in Power Saving
Mode (page 24).

continued

15GB

Listening to non-preset radio
station

Using the Radio Data
System (RDS)

— Manual Tuning

1
2
3
4

(European model only)
Press TUNER BAND (or FUNCTION
repeatedly) to switch the function to
TUNER.
Press TUNER BAND repeatedly to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
“AUTO” and “PRESET” disappear from
the display.
Press + or – (or turn – TUNING + on the
unit) repeatedly to tune in the desired
station.

Note

When switching to CD function from tuner, a longer
time may be required to access the disc. In this case, set
“CD POWER ON” by CD power manage function
(page 15).
Tips

• To improve broadcast reception, adjust the supplied
antennas, or connect a commercially available
external antenna.
• When an FM stereo program has static noise, press
FM MODE repeatedly until “MONO” appears.
There will be no stereo effect, but the reception will
improve.
• Press TUNING MODE repeatedly until “AUTO”
appears in step 3 above, then press + or – (or turn –
TUNING + on the unit). The frequency indication
changes and scanning stops when the system tunes in
a station (Automatic Tuning).
• To record the radio programs, use manual recording
(page 18).

What is the Radio Data
System?
Radio Data System (RDS) is a broadcasting
service that allows radio stations to send
additional information along with the regular
program signal. RDS is available only on FM
stations.*
Note

RDS may not work properly if the station you are tuned
in is not transmitting the RDS signal properly or if the
signal is weak.
* Not all FM stations provide RDS service, nor do they
provide the same types of services. If you are not
familiar with the RDS system, check with your local
radio stations for details on RDS services in your
area.

Receiving RDS broadcasts
Simply select a station from the FM band.

When you tune in a station that provides RDS
services, the station name appears in the display.

To check the RDS information
Each time you press DISPLAY, the display
changes cyclically as follows:
Station name1) t Preset number2) and
frequency t Clock display (for eight seconds)
t Effect status
1)

If the RDS broadcast is not properly received, the
station name may not appear in the display.

2) Preset

number is displayed only if you preset radio
stations (page 14).

16GB

Other operations

Tape – Play

To

Do this

Stop play

Press x.

Loading a tape

Pause

Press X. Press again to resume
play.

Fast-forward or
rewind

Press m or M.

Remove a tape

Press PUSH Z on the unit in stop
mode.

Use buttons on the unit for the operation.

1

Press PUSH Z.
Load a recorded/recordable tape in
deck A or B with the side you want to
play/record facing forward.
With the side
you want to
play/record
facing
forward.

Searching for the beginning of
the current or the next track
(AMS)*
To go forward

Tape – Play

2
3

Press TAPE A/B repeatedly to select
deck A or B.

Press > (or turn l L on the unit
clockwise) during playback.
“TAPE A (or TAPE B) >>> +1” appears.

To go back
Press . (or turn l L on the unit
counterclockwise) during playback.
“TAPE A (or TAPE B) <<< –1” appears.

Playing a tape
You can use TYPE I (normal) tape.

1

Load a tape.

To play both decks in succession, press
PLAY MODE repeatedly until “RELAY”
(Relay Play)* appears in the display.

2
3

Press TAPE (or FUNCTION repeatedly)
to switch the function to TAPE.

* AMS (Automatic Music Sensor)
Notes

• The AMS function may not operate correctly under
the following circumstances:
– When the unrecorded space between songs is less
than 4 seconds long.
– When the system is placed near a television.
• Do not eject the tape during playback or recording, as
this may cause irreparable damage to the tape and
cassette holder.

Press N.

The tape starts playing.
* After the playback of the front side of deck A, deck
B plays the front side, then stops.

17GB

Tape – Recording

Recording your favorite
CD tracks on a tape
— CD-TAPE Synchro Recording
You can record a whole CD on a tape.
You can use TYPE I (normal) tape. The
recording level is adjusted automatically.
Use buttons on the unit for the operation.

1
2

Load a recordable tape into deck B,
then press TAPE A/B repeatedly to
select deck B.
Press CD and load a disc you want to
record.

Recording on a tape
manually
— Manual Recording
You can record just the portions you like from a
CD, tape or radio program on a tape.
You can also record from connected
components (see “Hooking up optional
components” on page 27).
Use buttons on the unit for the operation.

1
2

Press CD SYNC.

Deck B stands by for recording.
“REC” flashes.

4

Press REC PAUSE/START.

Recording starts. When the recording is
completed, the CD player and the tape deck
stop automatically.

To stop recording
Press x.

Press one of the following buttons to
select the desired source to record.

• CD: To record from this system’s CD
player.
• TAPE A/B: To record from this system’s
tape deck A.
• TUNER/BAND: To record from this
system’s tuner.
• AUDIO IN: To record from the optional
component connected to the AUDIO IN
jack.

If you have already loaded the disc, press
DISC SKIP/EX-CHANGE to select the
disc.
When you want to record an album from an
MP3 disc, be sure to press PLAY MODE
repeatedly to select ALBM, then press
ALBUM + or – repeatedly to select the
desired album before proceeding.

3

Load a recordable tape into deck B,
then press TAPE A/B repeatedly to
select deck B.

3

Press REC PAUSE/START.

Deck B stands by for recording.
“REC” flashes.

4

Press REC PAUSE/START, then start
playing the desired source to record.

Recording starts.

To stop recording
Press x.
Notes

To record a disc by specifying
track order
You can record only your favorite CD tracks
using Program Play. Between steps 2 and 3,
perform steps 2 to 6 of “Creating your own
program” (page 13).

18GB

• You cannot listen to other sources while recording.
• Recording stops if you change the function to another
one.
Tip

For recording from the tuner:
If noise is heard while recording from the tuner, move
the respective antenna to reduce the noise.

Sound Adjustment

Adjusting the sound
You can reinforce the bass and create a more
powerful sound.
Press GROOVE on the unit.

Each time you press the button, the display
changes cyclically as follows:
GROOVE ON* t GROOVE OFF

Using the sub woofer
(MHC-GX555/RG575S/RG475S only)
You can use the sound of the sub woofer to suit
the sound source.
Press SUBWOOFER ON/OFF on the unit.

Each time you press the button, the display
changes cyclically as follows:
SUB ON* t SUB OFF
* The SUBWOOFER ON/OFF indicator lights up.

Selecting the effect from the
music menu
Press EQ (or PRESET EQ on the unit)
repeatedly to select the preset you desire.

The preset name appears in the display.
See the chart “Sound effect options”.

To cancel the sound effect
Press EFFECT ON/OFF on the unit.

Sound effect options
“SURR” appears if you select an effect with
surround effects.
EQ

ROCK
POP
JAZZ
DANCE
SOUL
ORIENTAL
REGGAE
SALSA
SAMBA

Tape – Recording/Sound Adjustment

* The volume switches to power mode, the equalizer
curve changes, and “GROOVE” lights up.

Selecting the sound effect

Note

Make sure to turn off the SUBWOOFER ON/OFF
indicator when the sub woofer is not connected to the
system.
Tip

You can use VOLUME +/– (or VOLUME control on
the unit) to adjust the volume of the sub woofer linked
to the front speakers.

19GB

Adjusting the graphic
equalizer and storing
You can adjust the sound by raising or lowering
the levels of specific frequency ranges, then
store up to three personal files (P FILE) in the
memory.
Before operation, first select the audio emphasis
you want for your basic sound.
Use buttons on the unit for the operation.

1

Press EQ BAND repeatedly to select a
frequency band, then turn – EQ + to
adjust the level.
Frequency band

2

Frequency level

Press and hold P FILE.

A personal file number appears.

3
4

Press P FILE repeatedly to select
P FILE 1 – 3 you want to store the
equalizer setting.
Press ENTER.

“COMPLETE” appears.
This setting is automatically stored as the
personal file you selected in step 3.

Other operations
To

Press

Call up a
personal file

P FILE repeatedly to select the
desired personal file number.

Cancel a personal EFFECT ON/OFF repeatedly
file
until “EFFECT OFF” appears.

20GB

Selecting the surround
effect
Press SURROUND on the unit.

Each time you press the button, the display
changes as follows:
SURROUND ON (SURR)
Y
SURROUND OFF (off)

Singing along: Karaoke
(Latin American model only)
You can sing along by connecting an optional
microphone. Use buttons on the unit for the
operation.

Mixing and recording sounds
You can “mix” sounds by playing one of the
components and singing or speaking into a
microphone (not supplied).
The mixed sound can be recorded on a tape.
Use buttons on the unit for the operation.

1

Enjoying karaoke

1
2

(Mexican model only)
Press MULTIPLEX repeatedly to obtain
the karaoke effect you desire.

Each time you press the button, the display
changes cyclically as follows:
MPX L t MPX R t MPX OFF
To sing karaoke of multiplex CD, select
“MPX L” or “MPX R”.

4
5

2

Connect an optional microphone to
MIC jack.

Start playing the music.
Adjust the microphone volume by
turning MIC LEVEL.

After you have finished
Turn MIC LEVEL to MIN and disconnect the
microphone from MIC jack.

Other operations
To

Do this

Cancel karaoke
mode*

Turn MIC LEVEL to MIN and
disconnect the microphone from
MIC jack, then press
MULTIPLEX repeatedly until
“m” disappears.

Adjust the
microphone
echo*

Turn ECHO LEVEL to adjust the
echo effect. To cancel the echoing,
turn ECHO LEVEL to MIN.

Use CD-Gs*

Turn on your TV and select the
correct video input.

Press the function button of the source
you want to record (e.g., CD).

When you want to record from TAPE A,
press TAPE A/B repeatedly until TAPE A
is selected.

3

Press REC PAUSE/START.

Deck B stands by for recording.
“REC” flashes.

4

Press REC PAUSE/START, and then
start singing, speaking or playing the
desired source.

Sound Adjustment

3

Turn MIC LEVEL to MIN to turn down
the microphone control level.

Prepare the source you want to mix.
Then, load a recordable tape in deck B
and press TAPE A/B repeatedly to
select deck B.

Recording starts.

To stop recording
Press x.
Note

Microphone does not function while the tape deck is
performing the AMS operation (page 17).
Tips

• If acoustic feedback (howling) occurs, move the
microphone away from the speakers or change the
direction of the microphone.
• If you want to record your voice through the
microphone only, you can do so by selecting the CD
function and not playing a disc.
• When high level sound signals are input, the system
automatically adjusts the recording level to prevent
distortion of the recorded sound signal (Auto Level
Control function).

* Mexican model only

21GB

Waking up to music

Timer

Falling asleep to music
— Sleep Timer
You can set the system to turn off after a certain
time, so that you can fall asleep to music.
Press SLEEP.

— Play Timer
You can wake up to music at a preset time. Make
sure you have set the clock (see “Setting the
clock” on page 9).
Use buttons on the remote for the operation.

1

Each time you press the button, the minute
display (the turn-off time) changes cyclically as
follows:
AUTO* t 90MIN t 80MIN t 70MIN
t … t 10MIN t OFF

• CD: Load a disc. To start from a specific
track, make a program (see “Creating
your own program” on page 13).
• Tape: Load a tape with the side you want
to play facing forward.
• Tuner: Tune in the preset radio station
(see “Listening to the radio” on page 15).

* The system automatically turns off in 100 minutes or
after the current disc or tape finishes playing.

Other operations
To

Press

Check the
remaining time*

SLEEP once.

Change the time
to turn off

SLEEP repeatedly to select the
time you want.

2
3
4

5

Do not set to “AUTO” during Synchro Recording on a
tape.
You can use the Sleep Timer, even if you have not set
the clock.

Press CLOCK/TIMER SET.
Press . or > repeatedly to select
“PLAY SET”, then press ENTER.

Set the time to start playing.

Press . or > repeatedly to set the
hour, then press ENTER.
The minute indication flashes.
Press . or > repeatedly to set the
minute, then press ENTER.

Note

Tip

Press VOLUME +/– to adjust the
volume.

“ON” appears and the hour indication
flashes.

Cancel the Sleep SLEEP repeatedly until “SLEEP
Timer function
OFF” appears.
* You cannot check the remaining time if you select
“AUTO”.

Prepare the sound source you want to
play.

6
7

Set the time to stop playing following
the same procedure as step 5.
Press . or > repeatedly until the
desired sound source appears.

Each time you press the button, the display
changes cyclically as follows:
t TUNER y CD PLAY T
t TAPE PLAY T

22GB

8

Press ENTER.

The type of timer (“PLAY TIMER”), the
start time, the stop time, and the sound
source appear in turn, before the original
display returns.

9

Timer recording radio
programs
— Rec Timer

Press ?/1 to turn off the system.

Other operations
To

Do this

Activate the timer/
Check the setting

1 Press CLOCK/TIMER
SELECT.

2 Press . or >
repeatedly until “PLAY
SELECT” appears, then
press ENTER.
Change the setting

Start over from step 1.

Cancel the timer

1 Press CLOCK/TIMER
SELECT.
repeatedly until “TIMER
OFF” appears, then press
ENTER.

Notes

• You cannot activate the Play Timer and the Rec
Timer at the same time.
• If you use the Play Timer and the Sleep Timer at the
same time, the Sleep Timer has priority.
• If the system is on at the preset time, the Play Timer
will not be activated.
• The Play Timer setting remains as long as the setting
is not canceled manually.

1
2
3

Tune in the preset radio station (see
“Listening to a preset station” on
page 15).
Press CLOCK/TIMER SET.
Press . or > repeatedly to select
“REC SET”, then press ENTER.

“ON” appears and the hour indication
flashes.

4

Timer

2 Press . or >

You can record a preset radio station from a
specified time.
To timer record, you must first preset the radio
station (see “Presetting radio stations” on
page 14) and set the clock (see “Setting the
clock” on page 9).
Use buttons on the remote for the operation.

Set the time to start recording.

Press . or > repeatedly to set the
hour, then press ENTER.
The minute indication flashes.
Press . or > repeatedly to set the
minute, then press ENTER.

5

Set the time to stop recording following
the same procedure as step 4.

The type of timer (“REC TIMER”), the start
time, the stop time, and the preset radio
station to be recorded (e.g., “TUNER FM
5”) appear in turn, before the original
display returns.

Tip

The system turns on 15 seconds before the preset time.

6
7

Load a recordable tape into deck B.
Press ?/1 to turn off the system.

continued

23GB

Other operations
To

Do this

Activate the timer/
Check the setting

1 Press CLOCK/TIMER
SELECT.

2 Press . or >
repeatedly until “REC
SELECT” appears, then
press ENTER.
Change the setting

Start over from step 1.

Cancel the timer

1 Press CLOCK/TIMER
SELECT.

2 Press . or >
repeatedly until “TIMER
OFF” appears, then press
ENTER.
Notes

• You cannot activate the Play Timer and the Rec
Timer at the same time.
• If you use the Rec Timer, the Play Timer and the
Sleep Timer at the same time, the Sleep Timer has
priority.
• If the system is on at the preset time, the Rec Timer
will not be activated.
• The volume is reduced to minimum during
recording.
• The Rec Timer is canceled automatically after the
Rec Timer has been activated.

Display

Turning off the display
— Power Saving Mode
The demonstration display (display window and
buttons lighting and flashing even when the
system power is off) and the clock display can
be turned off to minimize the amount of power
consumed during standby (Power Saving
Mode).
Press DISPLAY repeatedly while the
system is off until the demonstration
display or the clock display disappears.
To cancel Power Saving Mode

Press DISPLAY while the system is off. Each
time you press the button, the display switches
cyclically as follows:
Demonstration display t Clock display* t
No display (Power Saving Mode)
* The clock is displayed only if you set the clock.
Note

You cannot perform the following operations in Power
Saving Mode.
– setting the clock
– changing the AM tuning interval (except for
European, Russian and Saudi Arabian models)
– turning on the system by pressing the function
buttons (e.g., CD)
– changing the CD power manage function
Tips

• The timer continues to operate in Power Saving
Mode.
• ?/1 indicator lights up even in Power Saving Mode.

24GB

Viewing information
about the disc in the
display
You can check the playing time and remaining
time of the current track or that of the disc.
When a disc with MP3 audio tracks is loaded,
you can also check the information recorded on
disc, such as the titles.

Checking the remaining time
and titles
Press DISPLAY during Normal Play.

1)

2)

3)

“– –.– –” appears when playing back MP3 audio
tracks.
“– –.– –” appears in ALL DISCS, SHUFFLE or
Program Play mode or when playing back MP3
audio tracks.
When you play back a track with an ID3 tag ver. 1 or
ver. 2, the ID3 tag information appears. The ID3 tag
displays the track title, album name and artist name
information.

Press DISPLAY in stop mode.

Each time you press the button, the display
changes cyclically as follows:
x Normal Play mode

TOC display1) or total album number of the
disc2) or total track number of the current
album2) t Album name2) or volume label2) t
Clock display (for eight seconds) t Effect
status
1)

2)

TOC = Table of Contents; displays current disc
number, total number of tracks on the disc, and total
playing time of the disc.
For discs with MP3 audio tracks, album names or
volume label may not be displayed depending on the
play mode.

x Program Play mode

The last track number of the program and the
total playing time t Total track number of the
program (for five seconds) t Volume label*
t Clock display (for eight seconds) t Effect
status

Display

Each time you press the button, the display
changes cyclically as follows:
Current track number and elapsed playing time
t Current track number and remaining time1)
t Remaining time of the disc2) t Track title
and artist name (disc with MP3 audio tracks3)
only) t Album name (disc with MP3 audio
tracks3) only) t Clock display (for eight
seconds) t Effect status

Checking the total playing
time and titles

* For discs with MP3 audio tracks
Notes

• The total playing time is not displayed for a disc with
MP3 audio tracks.
• ID3 tag applies to version 1 and version 2.
• If the MP3 audio track you play back has an ID3 tag,
the ID3 tag information is displayed.
• In the following cases, elapsed playing time and
remaining time of the track may not be displayed
accurately.
– when an MP3 audio track of VBR (variable bit
rate) is played.
– when fast forward or fast reverse is performed.
• For Russian model, MP3 and ID3 tag information
can be displayed in Russian characters. However,
depending on the encoding/writing software or
recording device, the characters may not be correctly
displayed.

25GB

Changing the Power
illuminator

Viewing the tuner
information in the display

Press ILLUMINATION on the unit.

Press DISPLAY while listening to the radio.

Each time you press the button, the power
illuminator changes cyclically as follows:

Each time you press the button, the display
changes cyclically as follows:
Station name1) t Preset number2) and
frequency t Clock display (for eight seconds)
t Effect status

MHC-GX555/RG575S/RG475S/RG470

PATTERN 1 t PATTERN 2 t PATTERN 3
t ILLUM OFF
MHC-GX355/GX255/RG270/RG170

ILLUM ON y ILLUM OFF

26GB

1)
2)

European model only
Preset number is displayed only if you preset radio
stations (page 14).

Optional Components

Hooking up optional components
To enhance your system, you can connect optional components. Refer to the operating instructions
provided with each component. A North American model is used for illustration purpose.
Optional analog component
From the audio output jack of an
optional analog component

Use audio cord (not supplied) to connect an
optional analog component (Portable Audio
Player, etc.) to this jack. You can then record or
listen to the sound from the component through
this system.
Note

Before connecting or disconnecting the audio cord
(not supplied), press VOLUME – repeatedly (or turn
the VOLUME control on the unit couterclockwise) to
turn down the volume.

Listening to audio from a
connected component
1

Connect the audio cord (not supplied). See
“Hooking up optional components”.

2

Press FUNCTION repeatedly (or AUDIO IN
on the unit) until “AUDIO IN” appears.

3

Start playing the connected component.

Recording audio from
connected component
1
2

Connect the audio cord (not supplied).

Optional Components

A AUDIO IN jack

Start recording manually. See “Recording
on a tape manually” on page 18.

Notes

• If the connected component has the AVLS
(Automatic Volume Limiter System) function, be
sure to turn off the function when using the AUDIO
IN. Otherwise, you will have to turn up the volume
of the speaker, and that may cause distortion.
• If the connected component has the BASS BOOST
or MEGA BASS function, be sure to turn off the
function when using the AUDIO IN. Otherwise, the
sound from the speaker may be distorted.

27GB

General

Troubleshooting

Problems and remedies
Should you encounter a problem with your
system, do the following:

1

Make sure the power cord and speaker
cords are correctly and firmly connected.

2

Find your problem in the troubleshooting
checklist below and take the indicated
corrective action.

If the problem persists after doing all of the
above, consult your nearest Sony dealer.

When the ?/1 indicator flashes
Immediately unplug the power cord and
check the following items.
• If your system has a voltage selector, is the
voltage selector set to the correct voltage?
Check the voltage for your region, then
make sure the voltage selector is set
correctly.
• Are the + and – speaker cords shortcircuited?
• Are you using only the prescribed
speakers?
• Is anything blocking the ventilation holes
on the rear of the system?
Check all the above items and fix any
problems found. After ?/1 indicator stops
flashing, reconnect the power cord and turn
on the system. If the indicator still flashes, or
if the cause of the problem cannot be found
even after checking all the above items,
consult your nearest Sony dealer.

The display starts flashing as soon as you
plug in the power cord even though you have
not turned on the system (see step 6 of
“Hooking up the system” (page 6)).
• Press DISPLAY twice while the system is off. The
demonstration disappears.
“– –:– –” appears in the display.
• A power interruption has occurred. Set the clock
(page 9) and timer settings (pages 22 and 23)
again.
The clock setting/radio presetting/timer is
canceled.
• Redo the following:
– “Setting the clock” (page 9)
– “Presetting radio stations” (page 14)
– “Falling asleep to music” and “Waking up to
music” (page 22)
– “Timer recording radio programs” (page 23)
There is no sound.
• Press VOLUME +/– or turn VOLUME control on
the unit clockwise.
• Make sure the headphones are not connected.
• Check the speaker connections (page 6).
• There is no audio output during the Rec Timer.
Sound comes from one channel, or
unbalanced left and right volume.
• Place the speakers as symmetrically as possible.
• Connect the supplied speakers.
Sound lacks bass.
• Check that the speaker’s + and – jacks are
connected correctly.
There is severe hum or noise.
• Move the system away from the source of noise.
• Connect the system to a different wall outlet.
• Install a noise filter (commercially available) to
the power cord.
The timer cannot be set.
• Set the clock again (page 9).
The timer does not function.
• Check the timer setting and set the correct time
(pages 23 and 24).
• Cancel the Sleep Timer function (page 22).

28GB

The remote does not function.
• Remove the obstacle.
• Move the remote closer to the system.
• Point the remote at the system’s sensor.
• Replace the batteries (R6/size AA).
• Locate the system away from the fluorescent light.
There is acoustic feedback.
• Reduce the volume.
• For Latin American model, move the microphone
away from the speakers or change the direction of
the microphone.
The color irregularity on a TV screen persists.
• Turn off the TV set once, then turn it on after 15
to 30 minutes. If the color irregularity still
persists, place the speakers farther away from the
TV set.

CD/MP3 player
The disc tray does not open and “LOCKED”
appears.
• Contact your Sony dealer or local authorized Sony
service facility.

The disc does not eject.
• You cannot eject the disc during CD Synchro
Recording. Press x to cancel the CD Synchro
Recording, then press Z on the unit to eject the
disc.
• Consult your nearest Sony dealer.
There is no picture (Mexican model only).
• Check that the system is connected securely.
• Make sure you connect the system to the video
input jack of your TV (page 7).
• Make sure you turn on the TV and operate the TV
correctly.
• Make sure you select the video input on the TV so
that you can view the pictures from this system.
• This system conforms to the NTSC color system.
Make sure your TV (color) system is NTSC.
• Press CD (or FUNCTION repeatedly) to switch
the function to CD.

Disc access takes a long time.
• Set “CD POWER ON” by CD power manage
function (page 15).
The sound skips.
• Wipe the disc clean (page 33).
• Replace the disc.
• Try moving the system to a place without
vibration (e.g., on top of a stable stand).
• Try moving the speakers away from the system, or
placing them on separate stands. When you listen
to a track with bass sounds at high volume, the
speaker vibration may cause the sound to skip.
Play does not start from the first track.
• Press PLAY MODE repeatedly until both “PGM”
and “SHUF” disappear to return to Normal Play.
MP3 audio track cannot be played back.
• Recording was not performed according to the
ISO9660 Level 1 or Level 2 format or Joliet in the
expansion format.
• The MP3 audio track does not have the extension
“.MP3”.
• The data is not stored in MP3 format.
• Discs containing files other than MPEG 1 Audio
Layer-3 files cannot be played.

Troubleshooting

The disc tray does not close.
• Place the disc correctly.
• Always close the tray by pressing Z on the unit.
Trying to press the tray closed with your fingers
may cause problems with the player.

Play does not start.
• Open the disc tray and check whether a disc is
loaded.
• Wipe the disc clean (page 33).
• Replace the disc.
• Place the disc that this system can play (page 4).
• Place the disc correctly.
• Place the disc in the tray with the label side up.
• Remove the disc and wipe away the moisture on
the disc, then leave the system turned on for a few
hours until the moisture evaporates.
• Press N to start play.

MP3 audio tracks take longer to play back than
others.
• After the system reads all tracks on the discs,
playback may take more time than usual if:
– the number of albums or tracks on the disc is
very large.
– the album and track organization structure is
very complex.

continued

29GB

The album name, track title and ID3 tag
information do not appear correctly.
• Use a disc that conforms with ISO9660 Level 1,
Level 2 or Joliet in the expansion format.
• The disc ID3 tag is not ver. 1 nor ver. 2.
• Only up to 30 characters of ID3 tags are displayed.
• The characters that can be displayed by this
system are as follows:
– Upper cases (A to Z)
– Numbers (0 to 9)
– Symbols (’< > * + , – / @ [ \ ] _)
Other characters may not be displayed correctly.

Noise increases or the high frequencies are
erased.
• The record/playback heads are magnetized.
Demagnetize them (page 33).

Tuner

If the system still does not
operate properly after performing
the above measures, reset the
system as follows:

Severe hum or noise/stations cannot be
received. (“TUNED” or “STEREO” flashes in
the display.)
• Set the proper band and frequency (page 14).
• Connect the antenna properly (page 7).
• Find a place and an orientation that provide good
reception, then set up the antenna again. If you
cannot obtain good reception, we recommend you
connect a commercially available external
antenna.
• The supplied FM lead antenna receives signals
along its entire length, so make sure you extend it
fully.
• Locate the antennas as far away from the speaker
cords as possible.
• Try turning off surrounding electrical equipment.
• Set “CD POWER OFF” by CD power manage
function (page 15).
A stereo FM program cannot be received in
stereo.
• Press FM MODE repeatedly until “STEREO”
appears.

Tape deck
The tape does not record or play, or there is a
decrease in sound level.
• The heads are dirty. Clean them (page 33).
• The record/playback heads are magnetized.
Demagnetize them (page 33).
The tape does not erase completely.
• The record/playback heads are magnetized.
Demagnetize them (page 33).
There is excessive wow or flutter, or the sound
drops out.
• The capstans or pinch rollers are dirty. Clean them
(page 33).

30GB

The tape does not record.
• No cassette is loaded. Load a cassette.
• The tab has been removed from the cassette.
Cover the broken tab with adhesive tape
(page 33).
• The tape has wound to the end.

Use buttons on the unit for the operation.

1
2
3
4

Disconnect the power cord.
Reconnect the power cord.
Press ?/1 to turn on the system.
Press x, ILLUMINATION and DISC 1 at the
same time.

The system is reset to the factory settings. You
should set the settings you made, such as the
preset stations, clock, and timer.
Note

You cannot reset the system to the factory settings in
Power Saving Mode (page 24).

Messages
One of the following messages may appear or
flash in the display during operation.

CD/MP3
NO DISC
There is no disc in the player or you have loaded a
disc that cannot be played on this system (such as
DVD, VCD, or CD-ROM without MP3 audio
tracks, etc.).

SET TIMER
You tried to select the timer when the Play Timer or
Rec Timer are not set.
TIME NG
The Play Timer or Rec Timer start and end times are
set to the same time.

Other
NOT IN USE
You pressed an invalid button.

NO STEP
All of the programmed tracks have been erased.
OVER
You have reached the end of the disc while pressing
M during playback or pause.
PUSH STOP
You pressed PLAY MODE during playback.
READING
The system is reading information of the disc. Some
buttons are not available.
STEP FULL
You tried to program 26 or more tracks (steps).

COMPLETE
The preset operation ended normally.

Tape

Troubleshooting

Tuner

NO TAB
You cannot record the tape because the tab has been
removed from the cassette.
NO TAPE
There is no tape in the tape deck.

Timer
PUSH SELECT
You tried to set the clock or timer during timer
operation.
SET CLOCK
You tried to select the timer when the clock is not
set.

31GB

On the speaker system

Additional Information

Precautions
On operating voltage
Before operating the system, check that the operating
voltage of your system is identical with the voltage of
your local power supply.

On safety

This speaker system is not magnetically shielded and
the picture on TV sets may become magnetically
distorted. In such a case, turn off the power of the TV
set once, and after 15 to 30 minutes turn it on again.
If there seems to be no improvement, locate the
speaker system further away from the TV set.
(Mexican model only)

In case color irregularity is observed
on nearby a TV screen

• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• Unplug the system from the wall outlet (mains) if it
is not to be used for an extended period of time. To
disconnect the power cord (mains lead), pull it out by
the plug. Never pull the cord itself.
• Should any solid object or liquid fall into the system,
unplug the system and have it checked by qualified
personnel before operating it any further.
• AC power cord must be changed only at the qualified
service shop.

With the magnetically shielded type of front speaker
system, the front speakers can be installed near a TV
set. However, color irregularity may still be observed
on the TV screen depending on the type of your TV set.

On placement

Place the speakers farther away from the TV set.

• Do not place the system in an inclined position.
• Do not place the system in locations where it is;
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight.
• Use caution when placing the unit or speakers on
surfaces that have been specially treated (with wax,
oil, polish, etc.) as staining or discoloration of the
surface may result.

On heat buildup
• Although the system heats up during operation, this
is not a malfunction.
• Place the system in a location with adequate
ventilation to prevent heat buildup in the system.
• If you continuously use this system at a high volume,
the cabinet temperature of the top, side and bottom
rises considerably. To avoid burning yourself, do not
touch the cabinet.
• To prevent a malfunction, do not cover the
ventilation hole for the cooling fan.

32GB

(Except for Mexican model)

If color irregularity is observed…
Turn off the TV set once, then turn it on after 15 to 30
minutes. Make sure you place the right speaker on the
right side and the left speaker on the left side of the
unit.

If color irregularity is observed
again…

IMPORTANT NOTICE
Caution: This system is capable of holding a still
video image or on-screen display image on your
television screen indefinitely. If you leave the still
video image or on-screen display image displayed
on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to
this.

On operation
• If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens inside the CD
player. Should this occur, the system will not operate
properly. Remove the disc and leave the system
turned on for about an hour until the moisture
evaporates.
• When you move the system, take out any disc.
If you have any questions or problems concerning your
system, please consult your nearest Sony dealer.

Notes on discs
• Before playing, clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight.
• When using discs that have glue or similar tacky
substance on the label side of the disc or that used a
special ink when the label was printed, there is a
chance that the disc or label may become attached to
parts inside this unit. When this occurs, it may not be
possible to remove the disc, and may also cause this
unit to malfunction. Be sure to check that the label
side of the disc is not sticky before using.
The following types of disc should not be used:
– Rental or used discs with attached seals where the
glue extends beyond the seal. The perimeter of the
seal on the disc is tacky.
– Discs that have labels printed using a special ink
that feels tacky when touched.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to do
so may damage the unit. Do not use such discs.

When using a tape longer than
90 minutes
The tape is very elastic. Do not change the tape
operations such as play, stop, and fast-winding
frequently. The tape may get entangled in the tape
deck.

Cleaning the tape heads
Clean the tape heads after every 10 hours of use. Be
sure to clean the tape heads before you start an
important recording or after playing an old tape. Use a
separately sold dry-type or wet-type cleaning cassette.
For details, refer to the instructions of the cleaning
cassette.

Demagnetizing the tape heads
Demagnetize the tape heads and the metal parts that
have contact with the tape after every 20 to 30 hours of
use with a separately sold demagnetizing cassette. For
details, refer to the instructions of the demagnetizing
cassette.

Cleaning the cabinet
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with mild detergent solution. Do not
use any type of abrasive pad, scouring powder or
solvent such as thinner, benzine or alcohol.

To prevent a tape from being accidentally recorded
over, break off the cassette tab from side A or B as
illustrated.
Break off the
cassette tab

Additional Information

To save a tape permanently

If you later want to reuse the tape for recording, cover
the broken tab with adhesive tape.

Before placing a cassette in the tape
deck
Take up any slack in the tape. Otherwise, the tape may
get entangled in the parts of the tape deck and become
damaged.

33GB

Specifications
Amplifier section
AUDIO POWER SPECIFICATIONS
(MHC-GX555/GX355 USA model only)
MHC-GX555
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:

MHC-GX255
Continuous RMS power output (reference):
65 + 65 watts (6 ohms at
1 kHz, 10% THD)
Total harmonic distortion less than 0.07% (6 ohms at
1 kHz, 40 W)

European and Russian models:
MHC-RG475S

North American model:

Front speaker
DIN power output (rated): 110 + 110 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
140 + 140 watts (6 ohms at
1 kHz, 10% THD)
Music power output (reference):
280 + 280 watts (6 ohms at
1 kHz, 10% THD)
Sub woofer
DIN power output (rated): 130 watts (6 ohms at
80 Hz, DIN)
Continuous RMS power output (reference):
160 watts (6 ohms at
80 Hz, 10% THD)
Music power output (reference):
320 watts (6 ohms at
80 Hz, 10% THD)

MHC-GX555

MHC-RG470

Front speaker
Continuous RMS power output (reference):
145 + 145 watts (6 ohms at
1 kHz, 10% THD)
Total harmonic distortion less than 0.07% (6 ohms at
1 kHz, 80 W)
Sub woofer
Continuous RMS power output (reference):
170 watts (6 ohms at
80 Hz, 10% THD)
Total harmonic distortion less than 0.07% (6 ohms at
80 Hz, 90 W)

DIN power output (rated): 110 + 110 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
140 + 140 watts (6 ohms at
1 kHz, 10% THD)
Music power output (reference):
280 + 280 watts (6 ohms at
1 kHz, 10% THD)

With 6 ohm loads, both channels driven, from
120 – 10,000 Hz: rated 145 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
MHC-GX355
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:

With 6 ohm loads, both channels driven, from
120 – 10,000 Hz: rated 150 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.

MHC-GX355
Continuous RMS power output (reference):
150 + 150 watts (6 ohms at
1 kHz, 10% THD)
Total harmonic distortion less than 0.07% (6 ohms at
1 kHz, 80 W)

34GB

Canadian model:

MHC-RG270
DIN power output (rated): 80 + 80 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
100 + 100 watts (6 ohms at
1 kHz, 10% THD)
Music power output (reference):
200 + 200 watts (6 ohms at
1 kHz, 10% THD)

MHC-RG170

MHC-RG270

DIN power output (rated): 20 + 20 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
25 + 25 watts (6 ohms at
1 kHz, 10% THD)
Music power output (reference):
50 + 50 watts (6 ohms at
1 kHz, 10% THD)

The following measured at AC 120, 127, 220, 240 V
50/60 Hz
DIN power output (rated): 100 + 100 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
125 + 125 watts (6 ohms at
1 kHz, 10% THD)

Other models:
MHC-RG575S
The following measured at AC 120, 127, 220, 240 V
50/60 Hz
Front speaker
DIN power output (rated): 100 + 100 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
125 + 125 watts (6 ohms at
1 kHz, 10% THD)
Sub woofer
DIN power output (rated): 120 watts (6 ohms at
80 Hz, DIN)
Continuous RMS power output (reference):
150 watts (6 ohms at
80 Hz, 10% THD)

MHC-RG475S

MHC-RG470
The following measured at AC 120, 127, 220, 240 V
50/60 Hz
DIN power output (rated): 130 + 130 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
160 + 160 watts (6 ohms at
1 kHz, 10% THD)

The following measured at AC 120, 127, 220, 240 V
50/60 Hz
DIN power output (rated): 50 + 50 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
65 + 65 watts (6 ohms at
1 kHz, 10% THD)
Inputs
AUDIO IN (stereo mini jack):
voltage 250 mV,
impedance 47 kilohms
MIC (phone jack) (Latin American model only):
sensitivity 1 mV,
impedance 10 kilohms
Outputs
PHONES (stereo mini jack):
accepts headphones of
8 ohms or more
VIDEO OUT (phono jack) (Mexican model only):
max. output level 1Vp-p,
unbalanced, Sync
negative, load impedance
75 ohms
SPEAKER:
accepts impedance of 6 to
16 ohms
SUBWOOFER OUT (MHC-GX555/RG575S/
RG475S only):
accepts impedance of 6 to
16 ohms

CD player section
System

Compact disc and digital
audio system
Laser Diode Properties
Emission duration:
continuous
Laser Output*:
Less than 44.6µW
* This output is the value measurement at a distance of
200mm from the objective lens surface on the
Optical Pick-up Block with 7mm aperture.
Frequency response
Signal-to-noise ratio
Dynamic range

Additional Information

Front speaker
The following measured at AC 120, 127, 220, 240 V
50/60 Hz
DIN power output (rated): 100 + 100 watts (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
120 + 120 watts (6 ohms at
1 kHz, 10% THD)
Sub woofer
DIN power output (rated): 120 watts (6 ohms at
80 Hz, DIN)
Continuous RMS power output (reference):
150 watts (6 ohms at
80 Hz, 10% THD)

MHC-RG170

2 Hz – 20 kHz (±0.5 dB)
More than 90 dB
More than 90 dB

continued

35GB

Speaker

Tape deck section
Recording system
Frequency response

Wow and flutter

4-track 2-channel, stereo
50 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassettes
±0.15% W. Peak (IEC)
0.1% W. RMS (NAB)
±0.2% W. Peak (DIN)

Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
North American model:
Other models:
Antenna
Antenna terminals
Intermediate frequency
AM tuner section
Tuning range
Pan-American models:

87.5 – 108.0 MHz
(100 kHz step)
87.5 – 108.0 MHz
(50 kHz step)
FM lead antenna
75 ohms unbalanced
10.7 MHz

530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,710 kHz
(with the tuning interval
set at 9 kHz)
European, Russian and Saudi Arabian models:
531 – 1,602 kHz (with the
tuning interval set at
9 kHz)
Other models:
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
Antenna
AM loop antenna
Intermediate frequency
450 kHz

North American model:
Front speaker SS-GX555 for MHC-GX555
Speaker system
Speaker units
Woofer:
Sub woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

13 cm, cone type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 230 × 345 ×
235 mm
Approx. 3.8 kg net per
speaker

Sub woofer SS-WG555 for MHC-GX555
Speaker system
Speaker units
Woofer:
Nominal impedance
Dimensions (w/h/d)
Mass

Bass-reflex type
20 cm, cone type
6 ohms
Approx. 265 × 325 ×
330 mm
Approx. 5.5 kg

Front speaker SS-GX555 for MHC-GX355
Speaker system
Speaker units
Woofer:
Sub woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

3-way, 3-unit, bass-reflex
type
13 cm, cone type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 230 × 345 ×
235 mm
Approx. 3.8 kg net per
speaker

Canadian model:
Front speaker SS-GX255 for MHC-GX255
Speaker system
Speaker units
Super Tweeter:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

36GB

3-way, 3-unit, bass-reflex
type

3-way, 3-unit, bass-reflex
type
2 cm, dome type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 200 × 325 ×
230 mm
Approx. 3.0 kg net per
speaker

European and Russian models:
Front speaker SS-RG475 for MHC-RG475S
Speaker system
Speaker units
Woofer:
Sub woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

3-way, 3-unit, bass-reflex
type
13 cm, cone type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 230 × 345 ×
235 mm
Approx. 3.8 kg net per
speaker

Sub woofer SS-WG475 for MHC-RG475S
Speaker system
Speaker units
Woofer:
Nominal impedance
Dimensions (w/h/d)
Mass

Bass-reflex type

Speaker units
Sub Woofer:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)

3-way, 4-unit, bass-reflex
type

Speaker units
Woofer:
Sub woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

Mass

3-way, 3-unit, bass-reflex
type
13 cm, cone type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 230 × 345 ×
235 mm
Approx. 3.8 kg net per
speaker

2 cm, dome type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 200 × 325 ×
230 mm
Approx. 3.0 kg net per
speaker

Mexican model:
Front speaker SS-RG575AV for MHCRG575S

Speaker units
Sub Woofer:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

15 cm, cone type
15 cm, cone type
5 cm × 2, cone type
6 ohms
Approx. 245 × 380 ×
290 mm
Approx. 5.5 kg net per
speaker

Front speaker SS-RG475 for MHC-RG270
Speaker system

Speaker units
Super Tweeter:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)

3-way, 3-unit, bass-reflex
type

3-way, 4-unit, bass-reflex
type, magnetically
shielded type
15 cm, cone type
15 cm, cone type
5 cm × 2, cone type
6 ohms
Approx. 245 × 380 ×
240 mm
Approx. 5.9 kg net per
speaker

Sub woofer SS-WG575 for MHC-RG575S
Speaker system
Speaker units
Woofer:
Nominal impedance
Dimensions (w/h/d)
Mass

Bass-reflex type
20 cm, cone type
6 ohms
Approx. 265 × 325 ×
365 mm
Approx. 6.3 kg

Front speaker SS-RG575AV for MHCRG470
Speaker system

Speaker units
Sub Woofer:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

3-way, 4-unit, bass-reflex
type, magnetically
shielded type

Additional Information

Mass

Speaker system

Speaker system
20 cm, cone type
6 ohms
Approx. 265 × 325 ×
330 mm
Approx. 5.5 kg

Front speaker SS-RG575 for MHC-RG470
Speaker system

Front speaker SS-RG170E for MHC-RG170

15 cm, cone type
15 cm, cone type
5 cm × 2, cone type
6 ohms
Approx. 245 × 380 ×
240 mm
Approx. 5.9 kg net per
speaker

continued

37GB

Front speaker SS-RG475AV for MHCRG270
Speaker system

Speaker units
Woofer:
Sub woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

3-way, 3-unit, bass-reflex
type, magnetically
shielded type
13 cm, cone type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 230 × 345 ×
235 mm
Approx. 4.0 kg net per
speaker

Other models:
Front speaker SS-RG575 for MHC-RG575S
Speaker system
Speaker units
Sub Woofer:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

3-way, 4-unit, bass-reflex
type

Mass

Bass-reflex type
20 cm, cone type
6 ohms
Approx. 265 × 325 ×
365 mm
Approx. 6.3 kg

Front speaker SS-RG475 for MHC-RG475S
Speaker system
Speaker units
Sub woofer:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

38GB

Speaker system
Speaker units
Woofer:
Nominal impedance
Dimensions (w/h/d)
Mass

3-way, 3-unit, bass-reflex
type
13 cm, cone type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 230 × 345 ×
235 mm
Approx. 3.8 kg net per
speaker

Bass-reflex type
20 cm, cone type
6 ohms
Approx. 265 × 325 ×
330 mm
Approx. 5.5 kg

Front speaker SS-RG575 for MHC-RG470
Speaker system
Speaker units
Sub Woofer:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

15 cm, cone type
15 cm, cone type
5 cm × 2, cone type
6 ohms
Approx. 245 × 380 ×
290 mm
Approx. 5.5 kg net per
speaker

Sub woofer SS-WG575 for MHC-RG575S
Speaker system
Speaker units
Woofer:
Nominal impedance
Dimensions (w/h/d)

Sub woofer SS-WG475 for MHC-RG475S

3-way, 4-unit, bass-reflex
type
15 cm, cone type
15 cm, cone type
5 cm × 2, cone type
6 ohms
Approx. 245 × 380 ×
290 mm
Approx. 5.5 kg net per
speaker

Front speaker SS-RG475 for MHC-RG270
Speaker system
Speaker units
Woofer:
Sub woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

3-way, 3-unit, bass-reflex
type
13 cm, cone type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 230 × 345 ×
235 mm
Approx. 3.8 kg net per
speaker

Front speaker SS-RG170 for MHC-RG170
Speaker system
Speaker units
Super Tweeter:
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
Mass

3-way, 3-unit, bass-reflex
type
2 cm, dome type
13 cm, cone type
5 cm, cone type
6 ohms
Approx. 200 × 325 ×
230 mm
Approx. 3.0 kg net per
speaker

General
Power requirements
North American model: 120 V AC, 60 Hz
European and Russian models:
230 V AC, 50/60 Hz
Australian model:
230 – 240 V AC, 50/60 Hz
Argentine model:
220 V AC, 50/60 Hz
Mexican model:
127 V AC, 60 Hz
Saudi Arabian model:
120 – 127, 220 or
230 – 240 V AC, 50/60 Hz
Adjustable with voltage
selector
Other models:
120 V, 220 V or
230 – 240 V AC, 50/60 Hz
Adjustable with voltage
selector

Supplied accessories

Remote Commander (1)
R6 (Size AA) batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Video cable (Mexican
model only) (1)
Speaker pads
MHC-GX555/RG575S/
RG475S (12)
MHC-GX355/GX255/
RG470/RG270/RG170
(8)

Design and specifications are subject to change
without notice.

Additional Information

Power consumption
USA model:
MHC-GX555:
285 watts
MHC-GX355:
210 watts
Canadian model:
MHC-GX555:
380 VA
MHC-GX355:
290 VA
MHC-GX255:
110 watts
European and Russian models:
MHC-RG475S:
300 watts
0.25 watts (at the Power
Saving Mode)
MHC-RG470:
240 watts
0.25 watts (at the Power
Saving Mode)
MHC-RG270:
190 watts
0.25 watts (at the Power
Saving Mode)
MHC-RG170:
70 watts
0.25 watts (at the Power
Saving Mode)
Other models:
MHC-RG575S:
300 watts
MHC-RG475S:
300 watts
MHC-RG470:
170 watts
MHC-RG270:
210 watts
MHC-RG170:
125 watts

Mass (excl. speakers)
North American models:
MHC-GX555:
Approx. 10.5 kg
MHC-GX355:
Approx. 10.0 kg
Canadian model:
MHC-GX555:
Approx. 10.5 kg
MHC-GX355:
Approx. 10.0 kg
MHC-GX255:
Approx. 8.5 kg
European and Russian models:
MHC-RG475S:
Approx. 10.5 kg
MHC-RG470:
Approx. 10.0 kg
MHC-RG270:
Approx. 8.7 kg
MHC-RG170:
Approx. 7.2 kg
Other models:
MHC-RG575S:
Approx. 10.5 kg
MHC-RG475S:
Approx. 10.5 kg
MHC-RG470:
Approx. 10.4 kg
MHC-RG270:
Approx. 10.0 kg
MHC-RG170:
Approx. 8.5 kg

Dimensions (w/h/d) (excl. speakers)
Approx. 280 × 325 ×
430 mm

39GB

List of button locations and reference pages
How to use this page

Illustration number
r

Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.

TAPE A/B e; (17, 18, 21)
R
Name of button/part

R
Reference page

Main unit
BUTTON DESCRIPTIONS

ALPHABETICAL ORDER
A–O

P–Z

ALBUM +/– qs (11, 13, 18)
AUDIO IN wl (18, 27)
AUDIO IN jack wf (27)
CD es (8, 10, 13, 18)
CD SYNC wj (18)
Deck A wg (17)
Deck B qk (17, 18, 21)
DISC 1 – 3 qa (11, 13, 30)
DISC SKIP/EX-CHANGE qd
(10, 11, 13, 18)
Disc tray 0 (10)
DISPLAY 3 (16, 24, 25)
Display window 5
ECHO LEVEL1) wa (21)
EFFECT ON/OFF 4 (19)
ENTER 4 (13, 14, 20)
EQ BAND qs (20)
GROOVE 4 (19)
ILLUMINATION 2 (26, 30)
MIC jack2) wd (21)
MIC LEVEL2) ws (21)
MULTIPLEX1) 6 (21)
Operation Dial
(– EQ +/l L/
– TUNING +) qj (20/11, 13,
17/14, 15)

P FILE 4 (20)
PHONES jack w;
PLAY MODE 8 (11, 13, 17)
Power illuminator qg (26)
PRESET EQ 4 (19)
REC PAUSE/START wl (18, 21)
Remote sensor 7
SUBWOOFER ON/OFF3) 9
(19)
SURROUND 4 (20)
TAPE A/B e; (17, 18, 21)
TUNER/BAND ea (14, 15, 18)
TUNING MODE 8 (14, 15)
VOLUME control ql (19)

?/1 (power) 1 (8, 15, 24, 28,
30)
X (pause) qs (11, 17)
x (stop) qs (11, 17, 21, 30)
M (fast forward) qs (11, 17)
N (play) qs (11, 17)
m (rewind) qs (11, 17)
Z (eject) qf (10)
PUSH Z (deck B) (eject) qh (17)
Z PUSH (deck A) (eject) wh (17)
1)
2)

3)

1 2 3 456789q;

es
ea
e;
wl
wk
wj
wh
wg

L
l

j

H

S

s

A

B

wf
wd ws wa
40GB

Mexican model only
Latin American model only
(Mexican model comes with
2 microphone jacks)
MHC-GX555/RG575S/
RG475S only

qa
qs
qd
qf
qg
qh
qj
qk
ql
w;

Remote control
ALPHABETICAL ORDER

BUTTON DESCRIPTIONS

A–E

F–Z

ALBUM + qa (11, 13)
ALBUM – qd (11, 13)
CD qk (10, 13)
CLEAR qg (13)
CLOCK/TIMER SELECT 2
(23, 24)
CLOCK/TIMER SET 3 (9, 22,
23)
DISC SKIP q; (11, 13)
DISPLAY wa (16, 24, 25)
ENTER 9 (9, 13, 14, 22, 23)
EQ qf (19)

FM MODE 4 (16)
FUNCTION 6 (10, 13, 14, 15,
17, 27)
PLAY MODE w; (11, 13, 17)
REPEAT 4 (12)
SLEEP ws (22)
TAPE qj
TUNER BAND 5 (14, 15)
TUNER MEMORY ql (14)
TUNING MODE w; (14, 15)
VOLUME +/– qs (19, 22)

1
2
3
4
5
6
7
8

qg

9

qf

q;

qd

qa

Additional Information

ws
wa
w;
ql
qk
qj
qh

?/1 (power) 1 (8, 23)
m/M (rewind/fast forward)
7 (11, 17)
N (play) 8 (11, 17)
X (pause) 8 (11, 17)
x (stop) 8 (11, 17)
+/– (tuning) qh (14)
./> (go back/go forward)
qh (9, 11, 17)

qs

41GB

Sony Corporation Printed in China



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Page Count                      : 44
Page Mode                       : UseOutlines
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:96768736-2180-49a1-b8d4-9d1df0e91c45
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2005:01:12 20:41:40Z
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2005:02:18 12:05:09+09:00
Metadata Date                   : 2005:02:18 12:05:09+09:00
Document ID                     : uuid:58352a00-711e-4663-a8bd-7d8852a6d1ef
Format                          : application/pdf
Title                           : MHC-GX555/GX355/GX255/RG575S/RG475S/RG470/RG270/RG170
Creator                         : Sony Corporation
Author                          : Sony Corporation

EXIF Metadata provided by EXIF.tools