Sony Camcorder Hxc 100 Users Manual

HXC-100 to the manual 2fe16611-d58a-483c-8a30-ecabc4fec098

2015-01-23

: Sony Sony-Sony-Camcorder-Hxc-100-Users-Manual-287053 sony-sony-camcorder-hxc-100-users-manual-287053 sony pdf

Open the PDF directly: View PDF PDF.
Page Count: 41

DownloadSony Sony-Sony-Camcorder-Hxc-100-Users-Manual- HXC-100  Sony-sony-camcorder-hxc-100-users-manual
Open PDF In BrowserView PDF
4-137-706-01(1)

HD Color Camera

Operating Instructions
Before operating the unit, please read this manual thoroughly
and retain it for future reference.

HXC-100

© 2009 Sony Corporation

WARNING
To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC Rules.
For the customers in Europe
This product with the CE marking complies with both the EMC
Directive and the Low Voltage Directive issued by the
Commission of the European Community.
Compliance with these directives implies conformity to the
following European standards:
• EN60950-1: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environments:
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors), E4 (controlled EMC environment, ex. TV
studio).
The manufacturer of this product is Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is
Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Germany. For any service or guarantee matters
please refer to the addresses given in separate service or
guarantee documents.
For the State of California, USA only
Perchlorate Material - special handling may apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material : Lithium battery contains perchlorate.
For the customers in Taiwan only

2

Table of Contents

Table of Contents
Overview ................................................................... 3
Features ..........................................................................3
System Configuration ......................................................4
Standalone operation example ..................................4
System operation example (with a Camera Control
Unit) .......................................................................5
Parts Identification ...........................................................5
Front right ..................................................................5
Front left ....................................................................6
Rear ...........................................................................7
Operation panel .........................................................7
Connector panel ........................................................8

Installation ................................................................ 9
Connecting a Camera Control Unit (CCU) ......................9
Attaching a Lens ...........................................................10
Attaching a Viewfinder ..................................................10
Attaching a Microphone ................................................11
Mounting the Camera to a Tripod .................................12
Adjusting the Shoulder Pad Position .............................13

Preparatory Settings .............................................. 13
Adjusting the Black Balance and White Balance ..........13
Setting the Electronic Shutter ........................................14
Setting the Local Time ..................................................15
Adjusting the Flange Focal Length ................................15
Setting the Focus Assist Function .................................16
Setting the Camera Outputs ..........................................17
Outputting a Trunk Signal .............................................18

Basic Procedure for Shooting............................... 19
Menus ...................................................................... 20
Displaying Menu Pages ................................................20
Setting the Menu ...........................................................20
Editing the USER Menu ................................................21
OPERATION Menu .......................................................24
PAINT Menu ..................................................................28
MAINTENANCE Menu ..................................................30
FILE Menu .....................................................................32
DIAGNOSIS Menu ........................................................34

Appendices ............................................................. 34
Precautions ...................................................................34
Error Messages .............................................................35
Using a “Memory Stick” .................................................35
Specifications ................................................................36
Menu Tree .....................................................................38

Function-assignable switches

Overview
The HXC-100 is a 2/3-type high-definition portable video
camera equipped with CCD units for 2,200,000 pixels, which
can be used as a standalone camera as well as in a studio in
combination with the HXCU-100 Camera Control Unit.

The camera has buttons to which various functions can be
assigned on the side panel and the rear. You can activate your
desired function, such as electronic color-temperature
conversion, instantly when shooting by assigning it to one of
these buttons in advance.
Buttons on the handle are also available as function
assignable switches.

Auto Lens Aberration Compensation function
The camera incorporates the latest image capturing device
and digital signal-processing LSI, and it performs newly
developed digital transmission with the camera control unit
(CCU), thus yielding high picture quality and high stability in
image creation in addition to superior camera functions and
operability.

Features
High picture quality and high performance
The latest 2/3-type Progressive IT CCD units for 2,200,000
pixel achieve high sensitivity and low smear. In addition, the
14-bit A/D converter and an original developed signalprocessing LSI provide high picture quality of optimal grade.

Multiple formats
The camera covers 1080/59.94i, 720/59.94P, 1080/50i, and
720/50P.
With its wide-range down-converter, the camera also enables
output of high-quality SD signals (525i/625i) from the camera
and the connected CCU, establishing an optimum camera
system for SD-system operations.

Newly designed integrated unit with low center
of gravity
The camera has stylish appearance with low-slung design.
Even when used in combination with a studio-use viewfinder,
stable operation is achieved, thanks to its low center of gravity.

Optimized handle shape and VF slide
mechanism for stable shooting
A new handle design has been adopted. A slight protrusion of
the upper front part of the handle enables stable holding of the
camera while you are shooting, by holding the front part of the
handle. Furthermore, a slide mechanism is located at the
viewfinder attachment position. Any difference in weight
balance caused by having a different lens attached can be
counteracted by adjusting the viewfinder attachment position,
in combination with the movable shoulder pad position. This
provides the best balance for shooting with the camera on your
shoulder.

Position-adjustable shoulder pad
The position of the shoulder pad can be adjusted for stable
shooting according to the build of the camera operator, the
type of lens in use, or the shooting style.
A low-repulsion shoulder pad (position fixed) is available as an
option. (Part No.: A-8286-346-A)

The Auto Lens Aberration Compensation function (ALAC) is
provided with this camera. This automatically reduces
chromatic aberration of magnification when a lens that
supports auto aberration compensation is attached.
For details on lenses supporting auto aberration
compensation, contact a Sony sales representative or Sony
service representative.

Focus assist functions
The VF detail function and focus assist indicator function
facilitate focusing.

VF detail
Various functions are provided for the VF detail signal, which
can be added only on images on the viewfinder screen in order
to facilitate focusing in various situations: Functions for
coloring the VF detail signal, flickering the VF detail signal by
adding modulation, thickening the VF detail signal, and
automatically compensating the VF detail level according to
the zoom position.

Focus Assist Indicator
The focusing level indicator on the viewfinder screen provides
a guide for focusing. The best focus setting can be easily
determined by observing fluctuation of the level indicator as a
guide.

“Memory Stick” 1) operation
The camera is equipped with a “Memory Stick” port, which
enables setup data storage and software upgrading using a
“Memory Stick.”
1) “Memory Stick” and
Corporation.

are trademarks of Sony

Various color-reproduction functions
Selection of multiple gamma tables
Seven types of standard and 4 types of hyper gamma tables
are provided with this camera. The hyper gamma values
enable cinemalike image creations with wide dynamic range,
which are different from those achieved with conventional
video gamma.

Multimatrix color correction
In addition to the standard 6-axis matrix function, the camera
has a multimatrix function that permits you to adjust the hue
and chroma for color components in 16-axis directions
independently. This is quite useful in color matching among
multiple cameras.

Overview

3

Knee saturation

Versatile choices of viewfinders

Change of hue and decrease in chroma that occur in
highlighted areas can be compensated.
This enables reproduction of natural skin tones under strong
lighting.

Multiformat monochrome CRT viewfinders, HDVF-200 (2type) and HDVF-550 (5-type) can be selected for use in studio
and portable systems.
Color LCD viewfinders, HDVF-C35W (3.5-type), HDVFC730W (6.3-type), and HDVF-C950W (9-type), are also
selectable to cover various applications.

Low key saturation
Hue and chroma in low-key zones can be compensated. Thus,
compensation for color reproduction in all zones is enabled in
combination with matrix color compensation and knee
saturation functions.

Prevention of electrical shock
When the power connection is unsafe, the power supply from
the connected Camera Control Unit will be shut off.

Versatile detail control functions
Skin-tone detail function
This function allows control (emphasis or suppression) of the
detail level for just a certain hue or chroma area in the image,
by creating a detail gate signal from color components of your
specified hue, such as skin tones.

Detail boost-frequency control
The boost frequency can be adjusted from 20 to 30 MHz. This
allows the detail thickness to be set appropriately for the
subject, thus enabling more subtle image expression.

H/V ratio control
The ratio between horizontal and vertical detail can be
adjusted.

System Configuration
Peripherals and related devices for the camera are shown in
figures.
Note

Production of some of the peripherals and related devices
shown in the figures has been discontinued. For advice on
choosing devices, please contact your Sony dealer or a Sony
sales representative.

Standalone operation example
Microphone

HDVF-200/C35W Viewfinder

White/black limiter

Easy menu-based setting
Selections and settings for viewfinder display items, safetyzone marker 1) or center marker,2) screen size marker, etc. can
be made quickly and easily, using setup menus displayed on
the viewfinder screen or an external monitor.

CAC-12
Microphone
holder
Zoom Lens
(for ENG/EFP)

1) Safety zone marker: A box-shaped marker displayed on the
viewfinder screen which indicates 80%, 90%, 92.5%, or 95% of the
total screen area
2) Center marker: A cross-shaped marker which indicates the center
of the viewfinder screen

“Memory Stick”

Wide variety of viewfinder display options

VCT-U14
Tripod Adaptor

Along with items such as operation messages, a zebra
pattern,1) a safety-zone marker, and a center marker, camera
settings may also be displayed on the viewfinder screen.
Furthermore, there are various cautionary and warning
indications to be occasionally displayed, making it simple to
check the status of the camera.

Tripod for
portable
camera

HXC-100 Video output
HD-SDI/SD-SDI/VBS1)
(selectable)

CCA-5 cable

The white and black details can be limited independently.

AC adaptor
AN-DN10/DN2B
BC-L70/L160

AC power

1) Zebra pattern: A stripe pattern displayed on the viewfinder screen
which indicates the portions where the video level is above about
70% or 100%. Used to check the video level of the subject.

Digital triax transmission
The camera uses an industry standard dual-shield coaxial
(triax) camera cable for connection between the camera and a
CCU. Newly developed original digital transmission
technology is built into the camera, and high-quality pictures
can be transmitted between the camera and CCU, regardless
of the cable length.

4

Overview

RCP-700/900-series
Remote Control Panel

RM-B750/B150
Remote Control Unit

1) No subcarrier phase-lock function with respect to external
reference is available for the VBS signal output from the camera.

System operation example (with a Camera Control Unit)
HDVF-550/C730W/C950W
Viewfinder

Picture
Monitor

Microphone

Waveform
Monitor

HDVF-200/C35W
Viewfinder

VF attachment shoe a)

CAC-12
Microphone
Holder

BNC

Return video input

Intercom headset

HXC-100

Zoom Lens
(for ENG/EFP)

BNC

Video router
Sync input

Prompter video input
Video output
HD-SDI/SD-SDI/VBS

Triax cable b)
to router/switcher
“Memory Stick”

Power supply
for a script light
DC 12 V
(Max. 0.5 A)

VCT-U14
Tripod Adaptor

Tripod for
portable
camera

HXCU-100
Camera Control
Unit

AC power

CCA-5 cable
(attached to the front)

CAC-6
Return Video Selector

HKCU-FP1
Front Control Panel

RCP-700/900-series
Remote Control Panel

a) Supplied with the HDVF-550/C730W/C950W, Part No.: A-7612-405-E
b) 600 m (1969 ft) at maximum and 50 m (164 ft) at minimum when using Fujikura 8.5-mm dia. cables.
For information of other cables, see “About the distances of triax transmission” (page 35).

a INCOM (intercom) button (UC model)/ENG (engineer
line) button (CE model)
UC model: The intercom microphone is on while this button is
held pressed.
CE model: The intercom microphone is on and the engineer
line is selected while this button is held pressed.
You can also assign other functions with a menu operation.

Parts Identification
Front right
1
2
3

4

8

5
9
0
qa
qs

6

b RET 1 (return video 1) button
The return video 1 signal from the CCU is monitored on the
viewfinder screen while this button is held pressed. It functions
the same as the RET 1 button on the operation panel (page 7)
on the rear of the camera.
You can also assign other functions with a menu operation.
c Accessory shoe
To attach an accessory using a 1/4-inch screw.
Note

When you wish to replace it with a slide-type shoe, consult
Sony service personnel.

7

qh qg qf qd

d Viewfinder shoe
Mount a viewfinder.
For details, see “Attaching a Viewfinder” (page 10).
e Lens cable clamp
To secure the cable of the lens (optional).

Overview

5

f Lens mount cap
The cap can be removed by moving the lens fixing lever
upward. Always keep the lens mount covered with this cap
when a lens is not attached.
g Lens fixing lever
Move the lever down to secure the lens in the lens mount.
For details, see “Attaching a Lens” (page 10).
h Viewfinder front-rear position lock lever
The viewfinder position can be adjusted forward or backward
when the lock is released by the lever.
For details on the adjustment, see “To adjust the viewfinder’s
front-rear position” (page 10).
i Assignable buttons
You can assign a function to the upper button by using
ASSIGNABLE 1 and the lower button with ASSIGNABLE 2 on
the  page of the OPERATION menu.
j GAIN switch
To select the gain of the video amplifier based on lighting
conditions when the camera is used in standalone status
without connecting a CCU.
When shipped from the factory, the values set are L = 0 dB,
M = 6 dB, and H = 12 dB.

n “Memory Stick” slot and access lamp
When you insert a “Memory Stick” into the slot, the access
lamp lights in green.
The lamp is lit in red while writing/reading data to/from the
“Memory Stick.”
Note

When the access lamp is lit in red, do not insert/remove the
“Memory Stick” or turn off the camera.
o STATUS/CANCEL switch
STATUS: To display status information of this camera in the
viewfinder when no menu is displayed with the DISPLAY/
MENU switch set to DISPLAY.
CANCEL: To cancel changed settings or return the display to
the previous menu when a menu is displayed in the
viewfinder.
p Menu control knob (rotary encoder)
Used to select settings from menus displayed on the
viewfinder screen (by rotating it) and to confirm settings (by
pushing it).
This knob functions the same as that on the rear operation
panel.

Front left

k AUTO KNEE and output signal selection switch
To select the signal (color-bar signal or camera’s video signal)
to be used as output to a VTR, the viewfinder, or a video
monitor when the camera is used in standalone status without
connecting a CCU.
When the camera’s video signal is being used as output, the
auto knee function can be selected.
BARS/OFF: Output is a color-bar signal.
CAM/OFF: Output is the camera’s video signal. The auto knee
circuit is disabled.
CAM/ON: Output is the camera’s video signal. The auto knee
circuit is enabled.
l WHITE BAL (white balance memory selection) switch
To select the white balance adjustment method or the memory
used to store the adjusted value when the camera is used in
standalone status without connecting a CCU.
PRST (preset): White balance is adjusted to a preset value
corresponding to a color temperature of 3200K.
A: To select memory A.
B: To select memory B.
Note

When a CCU or an external control device, such as an RCP/
RM, is connected, the functions of 0 to qs are controlled from
the external device or the HKCU-FP1 attached to the CCU,
and the controls on the camera are disabled.
m DISPLAY/MENU switch
Select the display on the viewfinder screen.
DISPLAY: To display various textual information and markers,
such as messages showing the camera settings and
operating status, the center marker, and the safety zone
marker, in addition to camera images.
OFF: To not display textual information and markers.
MENU: To display menus for camera settings.
The switch functions the same as the DISPLAY/MENU switch
on the rear operation panel.

6

Overview

1
2

3

4
5
6
7

0
9

8

a Shoulder strap fitting post
Attach one end of a shoulder strap (optional, part No. A-6772374-C) to this fitting post and the other end to the fitting post
on the other side of the camera.
b VF (viewfinder) connector (20-pin)
Connect the cable of the viewfinder (optional).
c Filter select knob
Used to select the built-in ND filters (1: clear, 2: 1/4 ND, 3:
1/16 ND, 4: 1/64 ND).
d SHUTTER switch
When the camera is used in standalone status without
connecting a CCU, use this switch to turn ON or OFF the
electronic shutter and change (SEL) the shutter speed and
shutter mode.
For details, see “Setting the Electronic Shutter” (page 14).

e AUTO W/B BAL (white and black balance automatic
adjustment) switch
To automatically adjust white and black balance when the
camera is used in stand-alone status without connecting to a
CCU.
WHT: To automatically adjust white balance.
BLK: To automatically adjust black balance.
For details, see “Adjusting the Black Balance and White
Balance” (page 13).
f INTERCOM LEVEL control
To adjust the intercom/earphone volume level.
The intercom level adjustment is enabled when the LEVEL/
MIC switch on the UC-type operation panel (page 7) or the
LEVEL switch on the CE-type operation panel (page 8) on the
rear is set to “FRONT.”
g RET (return video) button
When this button is pressed, the picture on the viewfinder
changes to the return video signal selected with the RET 2/3/
4 select switch (page 7) on the operation panel on the rear of
the camera.
You can also assign other functions with a menu operation.
h LENS connector (12-pin)
Connect the lens cable. The camera can control the lens
functions through this cable.
i MIC 1 IN (microphone 1 input) connector (XLR 3-pin)
Connect a microphone.
This connector and the AUDIO IN CH1 connector are
alternately activated with the MIC 1 select switch on the rear
connector panel.
j Tripod mount (bottom)
Attach the VCT-U14 Tripod Adaptor when mounting the
camera on a tripod.

OFF: The tally lamp is prevented from lighting.
b Shoulder strap fitting post
c Operation panel (See “Operation panel”.)
d Camera Control Unit (CCU) connector (triax
connector)
Connect an HXCU-100 Camera Control Unit using a triax
cable.
e INTERCOM connector (XLR 5-pin)
Connect an XLR 5-pin headset for input and output of intercom
audio signals.
The connector can be used for communication over the
engineer line when the camera is in standby status.
f EARPHONE jack (stereo minijack)
For connecting an earphone for output of the intercom audio.
g Connector panel (See “Connector panel” on page 8.)
h CAMERA POWER switch and indicator
CCU: To operate on power supply via the connected CCU.
EXT: To operate on power supply through the DC IN
connector.
The indicator is lit in green during operation. It is lit in red while
standby power is being supplied from the CCU, even if the
switch is set to OFF.
i CALL button
When you press this button, the red tally lamp of the
connected external control device (RCP/RM, HKCU-FP1, etc.)
will light. Use to call the operator of the external control device.
j Shoulder pad
You can adjust the position on your shoulder.
For details, see “Adjusting the Shoulder Pad Position” (page
13).

For details, see “Mounting the Camera to a Tripod” (page 12).

Operation panel
Rear

UC type: Model for NTSC areas

1

1

2

RET1

RET

PGM1
LEVEL
REAR

MIC
ON

FRONT
PROD

OFF

3 4

5

234

PGM2

ASSIGNABLE
DISPLAY
OFF

2

MENU

INCOM

3
ENG

4
5
6
7
0
9 8

a Tally lamp and switch
ON: The tally lamp lights when a tally signal is input to the
connected CCU or a call signal is generated in response to
pressing of a CALL button.

INTERCOM

6

7

EARPHONE

8 9

a RET 1 (return video 1) button
The return video signal is displayed on the viewfinder screen
while the button is held pressed.
b RET (return video) button and 2/3/4 (return video 2/3/4)
select switch
When other return video systems are used in addition to return
video 1, the signal selected with the 2/3/4 switch is displayed
on the viewfinder screen while holding the RET button
pressed.

Overview

7

Note

The RET 1 button has priority over the RET (2/3/4) button if
both buttons are pressed.
c DISPLAY/MENU switch
This switch functions the same as the DISPLAY/MENU switch
on the front (page 6).
d ASSIGNABLE button
You can assign a function with ASSIGNABLE REAR on the
 page of the OPERATION menu.
e Menu control knob (rotary encoder)
This knob functions the same as the menu control knob on the
front (page 6).
f LEVEL/MIC (intercom level control/microphone)
switch
To determine whether to use the INTERCOM LEVEL control
(page 7) on the front and to turn the intercom headset
microphone ON/OFF.
Switch position

INTERCOM LEVEL
control on the front

Headset microphone

REAR/ON

Inactive

ON

REAR/OFF

FRONT: The levels adjusted on the rear panel can be totally
adjusted with the INTERCOM LEVEL control on the front.
h ENG (engineer line) control
To adjust the intercom audio listening level of the engineer line.
i PGM1 (program 1) and PGM2 (program 2) controls
To adjust the audio listening level of program 1 or program 2,
respectively.
j PROD (producer line) control
To adjust the intercom audio listening level of the producer
line.
k TRACKER control
To adjust the intercom audio listening level at the TRACKER
connector on the connector panel.

Connector panel
1

2

3

4 5

RET CTRL

TRACKER

DC OUT

6

7

REMOTE

PROMPTER
/GENLOCK
/RET

OFF

FRONT/OFF

Active

LINE MIC +48V

DC IN 10.5-17V

MIC1
FRONT REAR

LINE MIC +48V

TEST
OUT

AUDIO IN
CH1

CH2

g Line select switch
To select the intercom line:
PROD: Producer line
ENG: Engineer line

SDI

h INCOM (intercom) level control
To adjust the intercom audio listening level.

8

i PGM1 (program 1) and PGM2 (program 2) controls
To adjust the audio listening level of program 1 or program 2,
respectively.

2

RET1

RET

PGM1

3 4

5

234

PGM2

ASSIGNABLE
DISPLAY

MIC
LINE

LEVEL
REAR

MENU

ENG

PROD

TRACKER

FRONT

INTERCOM

6

7

EARPHONE

8 9 0

qa

1 to 5 are the same as those of the UC type.
f MIC LINE (intercom microphone line) switch
To select the talk line for intercom:
PROD: To talk over the producer line
OFF: To turn off the headset microphone for the intercom line
ENG: To talk over the engineer line
g LEVEL switch
REAR: The intercom audio listening level is adjusted with the
ENG or PROD control on this panel.

8

Overview

qa

a DC IN (DC power supply input) connector (XLR 4-pin)
For connection to an AC-DN10 AC Adaptor, etc. to supply
power to the camera.

c TRACKER connector (10-pin)
For external interfaces, such as intercom and tally.
d RET CTRL (return control) connector (6-pin)
For connection to a CAC-6 Return Video Selector.

OFF

PROD
OFF
ENG

0

b DC OUT (DC power supply output) connector (4-pin)
To supply power to a script light or equivalent (12 V DC, max.
0.5 A).

CE type: Models for PAL areas
1

9

e PROMPTER/GENLOCK/RET (prompter signal output/
external sync signal input/VBS return input) connector
(BNC type)
• When a CCU is connected, this connector outputs a VBS
prompter signal.
• When the camera is used in standalone status without
connecting a CCU, use this connector for input of an
external sync signal (BB or 3-level sync). If a VBS signal is
input, you can check the input image by pressing the RET
button.
Note

Even when a BB signal is used for the external sync signal, no
subcarrier phase-lock function is available for the VBS output
signal.

f REMOTE connector (8-pin)
For connection to an RM-B150/B750 Remote Control Unit or
RCP-700/900-series Remote Control Panel.

Installation

Note

When a CCU is used in combination, this connector functions
as the trunk signal input/output. Do not connect any remote
control device to this connector.
g TEST OUT connector (BNC type)
To output an analog signal.
This supplies a VBS signal, an HD-Y signal equal to the signal
output from the VF connector, an HD-SYNC signal, or an SDSYNC signal, depending on which of these you have selected
on the menu.
Note

The VBS output signal has no subcarrier phase-lock function
with respect to external sync signals.

Connecting a Camera Control Unit
(CCU)
When operating the camera in a system with a CCU, connect
between the CCU connector of the camera and the CAMERA
connector of the CCU, using a triax cable.
When required, secure the cable, using the supplied cable
clamp belt.

To use the cable clamp belt

1

h AUDIO IN CH1 connector (XLR 3-pin) and input select
switch
Connect a channel 1 audio signal and set the switch according
to the connected source device.
LINE: When a line-level (0 dBu) signal source is connected
MIC: When an external microphone is connected
+48V: To supply power of +48 V to the connected external
microphone
i MIC 1 (microphone 1) select switch
Select the microphone for channel 1.
FRONT: To use the microphone connected to the MIC 1 IN
connector
REAR: To use the microphone connected to the AUDIO IN
CH1 connector

Insert the belt bracket C into hole A or B of the cable
clamp belt.

C
A

2

1 Remove the back screw-hole cover on the top of
the camera and 2 secure the cable clamp belt to the
camera, using the two supplied screws (+B3×10).

2

j AUDIO IN CH2 connector (XLR 3-pin) and input select
switch
Connect a channel-2 audio signal and set the switch according
to the connected source device in the same manner as with
channel 1.
k SDI (serial digital interface) connector (BNC type)
For HD-SDI or SD-SDI signal output.
You can select from among camera line signal, return signal,
and VF signal for the output with a menu operation.

B

1

3

1 Release the buckle, 2 bundle the cable with the
belt, 3 then lock the buckle again.

1

3

2

Installation

9

4

Adjust the length by pulling down the end of the belt.

B

1

INCOM
RET

1

2
3

1

Attaching a Lens
For information on handling lenses, refer to the operation
manual for the particular lens

B

VF

A

1

LE
NS

SHUT

RET

5
1
2
3
4
5

C

2

TER WHT

OFF
ON

BLK

SEL

INETE

RCOM

LEVE

L

Loosen the viewfinder left-right positioning ring and
slide the viewfinder in the direction of arrow A.
The viewfinder stopper B automatically pops down.
Tighten the viewfinder left-right positioning ring to
secure the viewfinder at the most convenient
position.
Connect the viewfinder cable to the VF connector.

The viewfinder can slide in the range of 53 mm (2 1/8 inches).
Adjust the front-rear position so that you can easily operate it
on your shoulder.
1 Pulling the LOCK lever backward permits you to slide the
viewfinder backward or forward. 2 Adjust the viewfinder frontrear position and 3 lock it by returning the lever forward to the
original position.

4

Push the lens fixing lever A upward and remove the
lens mount cap from the lens mount.
Align the lens’ alignment pin C with the notch B in
the upper part of the lens mount and insert the lens
into the mount.
While supporting the lens, push the lens fixing lever
A downward to secure the lens.
Connect the lens cable to the LENS connector.
Secure the lens cable with the cable clamp.

Attaching a Viewfinder
Caution

When the viewfinder is attached, do not leave the camera with
the eyepiece facing the sun. Direct sunlight can enter through
the eyepiece, be focused in the viewfinder and cause fire.

Example: Attaching an HDVF-200 Viewfinder
For details on the viewfinder, refer to the operation manual for
the viewfinder.

10

3

VF

To adjust the viewfinder’s front-rear position

3

MIC

2

A

Installation

3
LOCK

2

1
LOCK lever

To detach the viewfinder
Loosen the viewfinder left-right positioning ring, pull the
viewfinder stopper, then pull out the viewfinder by sliding it in
the direction opposite to that when attached.

Status displays in the viewfinder
Besides the video image, the viewfinder can display
characters and messages showing the camera settings and
operation status, as well as items such as a center marker or
safety-zone marker.

When the DISPLAY/MENU switch is set to DISPLAY
Items set to ON using the menu or related switches will be
displayed.
1

2

0dB 1/125

7

9

0

F5.6

qa

!ND
!FAN
!EXT
!FORMAT

3

F255
12.5V

5600
1 W:A

8

FORMAT
:1080-59.94i
ASSIGNABLE1
:5600K
ASSIGNABLE2
:OFF
ASSIGNABLE REAR:OFF

4 5

3

EX Z55
TALK

6

1 2

:2
:MAX
:ON
:1080-59.94i

a Assignable button indication
The functions assigned to the assignable buttons are
indicated.
For the functions that can be assigned, see OPERATION
menu  (page 26).

a TALK indication
Displayed when the intercom microphone is set to ON.

b Format indication
The current video format is displayed.

b EX (lens extender) indication
Displayed when a lens extender is in use.

c ‘!’ indication area
This area is used to display abnormal statuses, using the ‘!’
IND function. Display options can be set, using the menu.

c Zoom position indication
Indicates the approximate position of the zoom lens variator
between wide angle (0) and telephoto (99).

For details, see OPERATION menu <‘!’ IND> (page 25).

d Battery voltage indication
When the CAMERA POWER switch is set to EXT, the DC IN
voltage is displayed.
When the switch is set to CCU, the internal voltage of the
camera is displayed.

Attaching a Microphone

e Focus position indication
Shows the focus position of a zoom lens as a numeric value (0
to 255 [infinity]).

For attaching to the microphone holder of the viewfinder, refer
to the instruction manual for the viewfinder.

f 5600K mode indication
Displayed when the internal electrical filter (5600K) is set to
ON.

A microphone can be attached to the camera, using the
microphone holder of the viewfinder or an optional CAC-12
Microphone Holder.

When the microphone is attached to the
microphone holder of the viewfinder
Secure the microphone cable A to the cable clamp B of the
camera.

g Filter indication
Displays the type of ND filter currently selected with a number
(1, 2, 3, or 4).
h White balance memory indication
Shows the currently selected white balance automatic
adjustment memory. This is not displayed when a CCU is
connected.
W:A: The WHITE BAL switch is set to A.
W:B: The WHITE BAL switch is set to B.
W:P: The WHITE BAL switch is set to PRST.

VF

i Gain value indication
Shows the video gain value (dB) set with the GAIN switch.

k F-value indication
Indicates the lens F (iris opening) value.

LE
NS

SHUT

j Shutter/ECS indication
Displays the shutter/ECS status. Nothing is displayed if the
electronic shutter is set to OFF.

MIC

A

RET

TER WHT

OFF
ON

BLK

SEL

INETE

RCOM

LEVE

L

B

When the STATUS/CANCEL switch is set to
STATUS
The status display is changed to show the following items:

Installation

11

To attach a microphone, using a CAC-12
When attaching a long-type microphone, such as an ECM674/678, use an optional CAC-12 Microphone Holder.

1

1 Remove the front screw-hole cover on the top then
2 fix the CAC-12 in place with the two screws (+B4×8)
supplied with the CAC-12.

2

2

CAC-12

1

Tripod adaptor

1
Platform

1

2

Loosen the screw to open the CAC-12 and attach the
microphone.
If the microphone diameter is small, attach the adaptor A
(supplied with the CAC-12 or the microphone) to the
microphone.

2

1
2

A

1 Attach the tripod adaptor to the tripod and 2
secure it with the screw.
Place the camera on the tripod adaptor and slide
forward it along the groove of the tripod adaptor until
it clicks.

To remove the camera from the tripod adaptor
Hold down the red button and pull the lever in the direction of
the arrow.

Mounting the Camera to a Tripod
Mount the camera to a tripod, using an optional VCT-U14
Tripod Adaptor.
Caution

• Select an appropriate hole from among those at the bottom
of the tripod adaptor considering the balance of the weight
of the camera and the tripod adaptor. If an inappropriate
hole is selected, the camera may fall over.
• Check that the size of the selected hole matches that of the
screw of the tripod. If they do not match, the tripod adaptor
cannot be attached to the tripod securely.

12

Installation

Lever
Red button

If the pin of the tripod adaptor does not return to its
original position
After removing the camera, if the pin of the tripod adaptor does
not return to its original position, hold down the red button and
move the lever in the direction of the arrow to return the pin to
its original position. It is not possible to mount a camera with
the pin not seated.

Original position

Preparatory Settings

Pin

Adjusting the Black Balance and White
Balance
In order to maintain high picture quality when using the
camera, it is necessary to set the black balance and white
balance appropriately for the conditions.

Adjusting the Shoulder Pad Position
1/

You can shift the shoulder pad in the range of 28 mm (1 8
inches). This adjustment helps you get the best balance for
shooting with the camera on your shoulder.

To adjust
1 Raise the lever in the center of the shoulder pad to unlock
the shoulder pad, 2 slide the shoulder pad backward or
forward until it is in the most convenient position, and 3 move
the lever down to lock the shoulder pad in the selected
position.
Shoulder pad lock lever

1
3

Note

When a CCU or an external control device, such as an RCP/
RM, is connected, the black balance and white balance are
controlled from the external device or the HKCU-FP1 attached
to the CCU, and adjustment on the camera is disabled.
Black balance adjustment
The black balance needs adjustment in situations like the
following:
• The first time the camera is used
• When the camera is used after a long period of disuse
• When the surrounding temperature changes greatly
• When the gain value is changed using the setup menus
Normally, there is no need to adjust the black balance every
time the camera is turned on.
White balance adjustment
Always adjust the white balance when lighting conditions
change.

To adjust the black balance
Push the AUTO W/B BAL switch to BLK.

SHUTTE
R
NS
LE OFF
WHT

ON

RET SEL

Bottom of the camera

BLK

INTERC

OM LE

VEL

AUTO W/B BAL switch

2

Shoulder pad

Automatic black balance adjustment begins.
In automatic adjustment of black balance, both the black set
and black balance are adjusted.
During adjustment, the message “ABB: EXECUTING” will be
displayed on the viewfinder screen.
When the adjustment process is completed, the message
“ABB: OK” will be displayed.
The adjusted value is automatically stored in memory.
The black balance values stored in memory will be preserved
even when the camera power is turned off.
Notes

• During black balance adjustment, the iris will be
automatically closed.
• During black balance adjustment, the gain switching circuit
will work automatically, and the viewfinder screen will flicker
several times. This is not a malfunction.

Preparatory Settings

13

To adjust the white balance

1

Select the built-in filter according to the lighting
conditions with the filter select knob (1: Clear, 2:
1/4 ND, 3: 1/16 ND, 4: 1/64 ND).

After about one second, the message “AWB: OK” will be
displayed, and the adjustment process will complete.
The adjusted value will be automatically stored in the selected
memory (A or B).
Note

When using a zoom lens with automatic iris control capability,
hunting1) may occur. Adjust the lens’ iris gain control (labeled
IG, IS, S, etc.).

Filter select knob

1) Hunting: The automatic iris responds over and over, and the image
repeatedly darkens and lightens.

For more information, refer to the operation manual for the
lens.

About white balance memory

2

Place a white pattern, as shown below, with the same
lighting conditions as the subject, and zoom in on it.
A white object (white cloth, a white wall, etc.) near the
subject may be used in place of a white pattern.
A rectangle centered in the screen:
The length of the sides must be at least 70% of the
height and width of the screen.

There are two white balance memories: A and B.
When you execute automatic white balance adjustment, the
adjusted white balance value and the setting of the filter select
knob will be stored in either memory A or B, selected with the
WHITE BAL switch.
The white balance values stored in memory will be preserved
even when power is turned off. When power is turned on
again, the white balance in memory corresponding to the
current WHITE BAL switch setting is retrieved.

If automatic black balance or white balance
adjustment fails

Within this rectangle, there must be an area of
white greater than 10% of the entire screen.

Note
Be careful not to have any spots of high illumination in the
rectangle.

3

4

Adjust the lens iris opening.
With a manually adjusted lens: Set the opening to an
appropriate value.
With a lens which has automatic iris control: Set the
lens’ automatic/manual iris control switch to
automatic.
Select white balance memory A or B with the WHITE
BAL switch and push the AUTO W/B BAL switch
toward WHT.

SHUTTE
R
NS
LE OFF
BLK

INTERC

OM LE

VEL

WHITE BAL switch
AUTO W/B BAL switch

Automatic white balance adjustment begins.
During adjustment, the message “AWB: EXECUTING” will be
displayed on the viewfinder screen.

Preparatory Settings

Setting the Electronic Shutter
This section explains the different modes which can be used
for the electronic shutter and gives the procedures for setting
the shutter mode and shutter speed.
Note

When a CCU or an external control device, such as an RCP/
RM, is connected, the electronic shutter is controlled from the
external control device or the HKCU-FP1 mounted on the
CCU, and the switch on the camera is disabled.

About the shutter modes
The shutter modes that can be used with the electronic shutter
of the camera and the shutter speeds that may be selected are
as follows:
Shutter mode

Shutter speed 1)

Standard

1/100, 1/125, 1/250,
Use to obtain clear
1/500, 1/1000, 1/2000 images of quickly moving
seconds
subjects

WHT

ON

RET SEL

14

If the adjustment process does not end successfully, the error
message “ABB: NG” or “AWB: NG” will be displayed on the
viewfinder screen for approximately three seconds.
If this error message is displayed, try the adjustment again.
If the error message continues to be displayed after several
attempts, the camera requires internal inspection.

ECS (Extended Continuously variable
Clear Scan)
in the range of 60.0
Hz to 4300 Hz

Usage

Use to obtain images of
video monitors without
horizontal striping

1) The values in the table are those with 59.94i. With other formats, the
available values may be different.

Note



With artificial lighting, particularly fluorescent lights and
mercury vapor lamps, the brightness appears to be constant,
but in fact the strength of the red, green, and blue components
varies with the power supply frequency. This phenomenon is
known as “flicker.” When using the electronic shutter under
these lighting conditions, there are certain cases in which the
flicker is more noticeable. In particular, color flicker is evident
when the power frequency is 60 Hz. In areas where the power
frequency is 50 Hz, setting the shutter speed to 1/100 second
will reduce the flicker.

USER
USER MENU CUSTOMIZE
ALL
OPERATION
PAINT
MAINTENANCE
FILE
DIAGNOSIS

4

Selecting the mode and speed of the shutter

Rotate the menu control knob to position the cursor
to MAINTENANCE and push on the menu control
knob.
The CONTENTS page of the MAINTENANCE menu is
displayed.
CONTENTS

The mode and the shutter speed in Standard mode are set
using the SHUTTER switch.

1

Push the SHUTTER switch from the ON position to the
SEL position.

SHUTTE
R
NS
LE OFF
ON

5

WHT

RET SEL

BLK

INTERC

M00 TOP

01.
02.
03.
04.
05.
06.
07.
08.
09.
10.

OM LE

VEL

Turn the menu control knob to scroll the page and
position the pointer to  then push on the
menu control knob.
The  page is displayed.

SHUTTER switch



M15 TOP

DATE/TIME

The current shutter setting will be displayed in the
viewfinder for about three seconds.

2008/12/23

08:32

Example: “Shutter: 1/250”

2

Push the SHUTTER switch to the SEL position again
before the display disappears. Repeat this action until
the desired mode or speed is displayed.
Example: with 59.94i
Standard mode

1/100

1/125

1/250

1/500

7
1/1000

1/2000

ECS mode

Setting the Local Time
When using the camera for the first time, set the built-in clock
to the local time, using the  page of the
MAINTENANCE menu displayed on the viewfinder screen.
For details on menu operations, see “Menus” (page 20).

1
2

3

6

Turn the menu control knob and set the date and time.
Push on the menu control knob to shift to the next digit.
When the date/time setting is completed, set the
DISPLAY/MENU switch to OFF to exit Menu mode.

Adjusting the Flange Focal Length
Adjustment of the flange focal length (the distance between
the lens mount attachment plane and the imaging plane) is
necessary in the following situations:
• The first time a lens is attached
• When changing lenses
• If the focus is not sharp at both telephoto and wide angle
when zooming

Turn on the camera.

The flange focal length can be more precisely adjusted by
using the focus assist indicators.

While holding the menu control knob pressed, set the
DISPLAY/MENU switch to MENU.
The camera enters Menu mode, and “TOP” is displayed at
the upper-right corner of the screen.

See “Displaying the focus assist indicators” (page 17) for the
focus assist indicators.

Rotate the menu control knob to set the cursor to
“TOP” and push on the menu control knob.
The TOP MENU screen is displayed.

Note

The various parts of the lens used in adjusting the flange focal
length are in different positions on different lenses. Refer to the
operation manual for the lens.

1

Set the iris control to manual and open the iris fully.

Preparatory Settings

15

2

Place the supplied flange focal length adjustment
chart approximately 3 meters from the camera and
adjust the lighting to get an appropriate video output
level.

4

Rotate the menu control knob to align the pointer to
OPERATION and push on the knob.
The CONTENTS page of the OPERATION menu is
displayed.
CONTENTS

About 3 meters (10 ft)

3
4
5
6
7
8
9

Loosen the Ff (flange focal length) ring lock screw.

5

With either manual or power zoom, set the zoom ring
to telephoto.

Set the zoom ring to wide angle.

6

Repeat steps 4 through 7 until the image is in focus at
both telephoto and wide angle.
Tighten the Ff ring lock screw.

Using the OPERATION menu, the assist functions for easier
focusing on the viewfinder screen can be activated.

Adding a VF detail signal
Adding a VF detail signal to sharp edges in the image on the
viewfinder screen makes it easier to check the focusing
condition by observing changes in the detail signal or in the
color converted from the detail signal (color detail).
The focus setting where the detail signal becomes strongest is
the best focus setting.

3

Turn on the camera.
Set the the DISPLAY/MENU switch to MENU while
holding the menu control knob pressed.
The camera enters Menu mode, and “TOP” is displayed at
the upper right corner of the screen.
Rotate the menu control knob to align the pointer to
“TOP” and push on the knob.
The TOP MENU screen is displayed.

USER
USER MENU CUSTOMIZE
ALL
OPERATION
PAINT
MAINTENANCE
FILE
DIAGNOSIS

16

Preparatory Settings

04 TOP

VF DETAIL : ON
25%
CRISP
:
0
FREQUENCY: 9M
FAT MODE : OFF
FLICKER : OFF
AREA
: 70%
ZOOM LINK: 100%
COLOR DETAIL : ON BLUE
PEAK COLOR : ON
CHROMA LEVEL: 100%

Setting the Focus Assist Function

1
2

TOP

Rotate the menu control knob to align the pointer to
 and push on the knob.
The  page is displayed.


Aim at the flange focal length adjustment chart and
turn the focus ring to focus the image.

Turn the Ff ring to bring the chart into focus.
Take care not to move the distance ring.

00

01.
02.<'!'IND>
03.
04.
05.
06.
07.
08.
09.
10.

7

Rotate the menu control knob to align the pointer to
the item to be set and push on the knob.
To use the VF detail signal
Set VF DETAIL to ON to activate the VF detail function to
add the detail signal to sharp edges in the image. You can
adjust the signal level (strength) in the range of 0 to 100%
(default 25%).
You can adjust the characteristics of the detail signal with
the menu items below:
CRISP: Adjust to eliminate fine portions of the detail
signal.
FREQUENCY: Change the detection band of sharp
edges.
FAT MODE: Turn the function ON/OFF to thicken the
detail signal.
FLICKER: Turn the function ON/OFF to flicker the detail
signal, which makes it easier to check the signal on a
CRT screen.
AREA: To limit the area where to display the detail signal.
ZOOM LINK: Set the VF detail level at the full WIDE
position. (The VF detail level changes according to the
zoom position.)
To use the color detail
Set COLOR DETAIL to ON to convert the VF detail signal
to a specified color. This makes it easier to check the
signal on an LCD screen, including the viewfinder screen.
The display color can be selected at the column next to
ON.
You can adjust the coloring with the menu items below:
PEAK COLOR: Turn the function ON/OFF to change the
color where the detail signal is strongest.
CHROMA LEVEL: To reduce the chroma components of
the video signal (only for video signals on the
viewfinder).
Rotate the menu control knob to display the desired
setting and push on the knob.

8

To finish the adjustments, set the DISPLAY/MENU
switch to OFF to exit Menu mode.

To use the area marker
Setting AREA MARKER to ON displays the detection area
of the focus as a marker on the viewfinder screen.
You can set the size and position of the detection area with
the menu items below.
SIZE: The size of the detection area can be changed. (If
the area size is too large, both the subject and the
background are included in the area, making the
indicator display easily deviate from the subject.)
POSITION: Roughly set the position of the detection area.
POSITION H: Finely adjust the position of the detection
area in the horizontal directions.
POSITION V: Finely adjust the position of the detection
area in the vertical directions.

Displaying the focus assist indicators
The focus assist indicator function extracts the irregularities of
a subject and converts the integrated values to a level
indicator, which shows the focus condition.
Level indicator (Its position and operations can be adjusted.)

4
Area marker to display the detection area of the focus (Its size
and position can be adjusted.)

The focus setting where the indicator shows the maximum
level is the best focus setting. (The range of the indicator
substantially changes depending on picture elements or
shooting environments. Adjust it with GAIN and OFFSET as
required.)

1
2

Display the CONTENTS page of the OPERATION
menu (referring to step 1 to 4 in “Adding a VF detail
signal”).
Rotate the menu control knob to align the pointer to
 and push on the menu control
knob.
The  page is displayed.

INDICATOR :
MODE
:
LEVEL
:
GAIN
:
OFFSET
:
AREA MARKER:
SIZE
:
POSITION :
POSITION H:
POSITION V:

3

05 TOP

OFF
BOX
BOTTOM
3
QUICK
50
50
ON
MIDDLE
CENTER
50
50

Rotate the menu control knob to align the pointer to
the item to be set and push on the knob.
To use the level indicator
Setting INDICATOR to ON displays the level indicator on
the viewfinder.
You can set the display format with the menu items below.
MODE: Set the type and position of the indicator.
LEVEL: Set the density and the response speed of the
indicator.
GAIN: Set the sensitivity of the indicator.1)
OFFSET: Set the offset of the focus detection value.2)
1) Normally, the sensitivity of the indicator is automatically set to
the optimum value in conjunction with the AREA MARKER
SIZE set value. Use this setting when an optimum sensitivity
value cannot be obtained, depending on the shooting
environment.
2) Normally, the optimum offset is automatically set in conjunction
with the AREA MARKER SIZE and MASTER GAIN set values.
Use this setting when the optimum offset cannot be obtained,
depending on the shooting environment.

5

Rotate the menu control knob to display the desired
setting and push on the knob.
To finish the adjustments, set the DISPLAY/MENU
switch to OFF to exit Menu mode.

.

Notes
• When INDICATOR is ON, the effect area marker is disabled
even if EFFECT is set ON on the  page.
• When AREA MARKER is ON, the safety zone marker is
disabled even if SAFETY ZONE is set ON on the  page.
• When displaying the focus assist indicators, check that the
flange focal length has been precisely adjusted.
See “Adjusting the Flange Focal Length” (page 15) for the
flange focal length.

Setting the Camera Outputs
You can specify video signals directly output from the camera,
with menu operations.
Note
The MAIN (camera picture), RET (return video), or VF (the same
picture as that displayed on the viewfinder screen) setting is common
to SD-SDI and VBS. Different signals cannot be output.

The menu pages used for the output settings have been
registered to the USER menu at the factory.
•  (U11)
•  (U16)
•  (U17)
•  (U18)
•  (U19)
Set the menu items on the above menu pages to the settings
shown in the following tables.
For details on menu operations and the USER menu, see
“Menus” on page 20.

Outputting the signal being shot (camera
picture)
The same textual information as that displayed on the
viewfinder screen can be added to the output signal by setting
CHARACTER to ON on the  or 
page.

Preparatory Settings

17

To output as HD-SDI
Menu page

Item

Setting



SDI OUT

ACTIVE



OUTPUT

MAIN

To output as SD-SDI
Menu page

Item

Setting



SDI OUT

ACTIVE

DOWN CONVERTER

ACTIVE



OUTPUT SIGNAL

MAIN



OUTPUT

SD-SDI

To output as VBS

Note

With the settings for outputting the same image as that on the
viewfinder, the output will be obtained in 1080i, even if the
format setting is 720P.

To output as HD-SDI
Menu page

Item

Setting

SDI OUT

ACTIVE

OUTPUT

VF

Menu page

Item

Setting



SDI OUT

ACTIVE

DOWN CONVERTER

ACTIVE

Menu page

Item

Setting





DOWN CONVERTER

ACTIVE





OUTPUT SIGNAL

MAIN



OUTPUT

VBS

Constantly outputting a return video
• When a CCU is connected, one of the signals being
supplied to the CCU can be output from the camera.
• The last selected return signal is output.
• The same character information as that displayed on the
viewfinder screen can be added to the output signal by
setting CHARACTER to ON on the  or  page.

To output as HD-SDI
Menu page

Item

Setting



SDI OUT

ACTIVE



OUTPUT

RET

To output as SD-SDI
Menu page

Item

Setting



SDI OUT

ACTIVE

DOWN CONVERTER

ACTIVE



OUTPUT SIGNAL

RET



OUTPUT

SD-SDI

Menu page

Item

Setting



DOWN CONVERTER

ACTIVE



OUTPUT SIGNAL

RET



OUTPUT

VBS

To output as VBS

Outputting the same image as that on the
viewfinder screen
• With HD-SDI, you can obtain a signal that includes the same
information as that being displayed on the viewfinder
according to the settings for VF MARKER, CHARACTER,
VF DETAIL, ZEBRA, etc. The ON/OFF or other settings for
adding information are common to those for the viewfinder.

18

The output is synchronized with switching among Y, R, G,
and B or switching to a return signal.
• With SD-SDI or VBS, the output is synchronized only with
switching between a return signal and the camera image. It
does not correspond to switching among Y, R, G, and B.
Information other than CHARACTER (such as VF
MARKER, VF DETAIL, and ZEBRA) cannot be added to the
output.

Preparatory Settings

To output as SD-SDI



OUTPUT SIGNAL

VF



OUTPUT

SD-SDI

Menu page

Item

Setting



DOWN CONVERTER

ACTIVE



OUTPUT SIGNAL

VF



OUTPUT

VBS

To output as VBS

Outputting a prompter signal
The VBS signal supplied to the PROMPTER connector of the
CCU is output from the PROMPTER/GENLOCK/RET
connector of the camera.

Outputting a Trunk Signal
The trunk signal can be used for communication between an
external device connected to the REMOTE connector of the
camera and an external device connected to the TRUNK
connector of the CCU.

To output the trunk signal from the REMOTE
connector
Menu page

Item

Setting



TRUNK

ON

Basic Procedure for
Shooting

• Settings for the output signals from the camera (page
17)
• Flange focal length setting (page 15)

4

For viewfinder settings, refer to the operation manual for
the viewfinder.

Note

When an HXCU-100 Camera Control Unit or an external
control device, such as an RCP-series Remote Control Panel,
is connected, the white balance, black balance and shutter
adjustments are controlled from the external device, and the
controls on the camera are disabled.

5
6

For operations on the external control device, refer to the
operation manual for the device.

1

2

Adjust the eyepiece focus as well as the contrast and
brightness of the viewfinder image.

Turn the camera on.
To operate the camera on power supplied through the DC
IN connector of the camera via an AC power adaptor, set
the CAMERA POWER switch to EXT.
To operate the camera on power via the connected
HXCU-100, set the CAMERA POWER switch to CCU.
Set the filter select knob and 5600K appropriately for
the lighting conditions.
Filter select knob setting

7
8
9

If required, switch on the center marker and/or safety
zone and zebra pattern in the viewfinder image, using
the OPERATION menu.
Check the sound system settings.
• Microphone connections
• Settings of the AUDIO IN switches
• Settings on the VTR (Refer to the operation manual for
the VTR.)
Adjust the white balance and black balance (page 13).
Turn the focusing ring so that the subject is sharply in
focus.
Set up the VTR according to your shooting objectives
then start recording, using the button on the VTR.
For details on VTR setup and operations, refer to the
operation manual for your VTR.

Filter select knob Lighting conditions
1 (CLEAR)

Indoor shooting

2 (1/4 ND)

Outdoor (cloudy or rainy) or indoor
shooting when you wish to reduce the
depth of field1)

3 (1/16 ND)

Outdoor shooting in daytime

4 (1/64ND)

Outdoor shooting when you wish to
reduce the depth of field, or especially
under bright outdoor ambient light

10When shooting is finished, stop recording, using the
button on the VTR.

1) Depth of field: This is the range over which the subject is
sharply in focus.

From the viewpoint of the characteristics of lenses,
shooting with the iris set in the range of F4 to F8 is
generally recommended for good quality pictures. Set the
filter select knob to bring the iris setting into that range.
However, this may not apply when special composition is
desired.
5600K setting
The 5600K ON/OFF function has been assigned to
assignable button 1 (front right, upper) at the factory.

3

5600K

Example of lighting conditions

OFF

Indoor shooting under lighting with lower color
temperature, such as a halogen or tungsten lamp

ON

Outdoor shooting in daytime, or indoor shooting
under lighting with higher color temperature

Check the settings of the camera.
• Settings of switches/control knobs
• Settings on the OPERATION menu (page 24) and the
PAINT menu (page 28)
• Electronic shutter setting (page 14)

Basic Procedure for Shooting

19



Menus
The menus displayed on the viewfinder screen enable various
settings of the camera.
The following controls are used to operate the menus.
To enter Menu mode, you can use the DISPLAY/MENU switch
either on the side or on the rear operation panel.
The menu control knob at the low on the front panel and that
on the rear operation panel function the same. Rotate the knob
to select menu items or values and push on it to register
(enter) the selection.
Front right

Push on

DISPLAY/MENU switch

Rotate

USER
USER MENU CUSTOMIZE
ALL
OPERATION
PAINT
MAINTENANCE
FILE
DIAGNOSIS

Menu

Purpose

USER

This menu can include menu pages selected
from among the OPERATION, PAINT,
MAINTENANCE, FILE, and DIAGNOSIS
menus, for convenience. Changing, adding,
and deleting pages can be performed with the
USER MENU CUSTOMIZE menu.

USER MENU
CUSTOMIZE

This menu allows you to edit the USER menu.
For details on the USER menu, see “Editing
the USER Menu” (page 21).

ALL

This menu permits you to control all items of
the OPERATION menu, PAINT menu,
MAINTENANCE menu, FILE menu, and
DIAGNOSIS menu as a single menu.

OPERATION

This menu contains items for camera operators
to operate the camera. It mainly permits
viewfinder, intercom, and switch settings.

PAINT

This menu contains items for making detailed
image adjustments while using a waveform
monitor to monitor the waveforms output from
the camera. Support of a video engineer is
usually required to use this menu.
Although you can also use an external control
device to set the items on this menu, the menu
is effective when using the camera by itself
outdoors.

MAINTENANCE

This menu contains items for performing
camera maintenance operations, such as
changing the system or setting infrequently
used “paint” items.

FILE

This menu is for performing file operations,
such as writing or clearing the reference file.

DIAGNOSIS

This menu enables you to confirm the selfdiagnostic information.

STATUS/CANCEL switch
Menu control knob
Rear operation panel
RET1

PGM1

RET

234

PGM2

ASSIGNABLE

Push on

DISPLAY
MIC
LINE

PROD
OFF

LEVEL
REAR

ENG

OFF
MENU

ENG

PROD

TRACKER

Rotate

FRONT

INTERCOM

EARPHONE

DISPLAY/MENU switch

Menu control knob

Displaying Menu Pages
To display a menu page
Set the DISPLAY/MENU switch to MENU.
The menu page last accessed will be displayed. If it is the first
time, the CONTENTS page of the USER menu will be
displayed.

To display the TOP MENU screen
If you set the DISPLAY/MENU switch to MENU while holding
the menu control knob pressed, “TOP” is displayed at the
upper right corner of the screen.
Turn the menu control knob to move the pointer (,) on the
display to “TOP” and push on the knob. The TOP MENU
screen is displayed, listing the available menus.

To disable the “TOP” indication
Turn the power off then on again, or set the DISPLAY/MENU
switch to MENU while holding the STATUS/ CANCEL switch
pressed toward CANCEL. This disables the TOP selection.

Setting the Menu
To select a menu on the TOP MENU screen
Rotate the menu control knob to align the pointer with the
desired menu indication then push on the knob.
The CONTENTS page (page No. 00) or the last accessed
page of the selected menu is displayed.

To select a page from a CONTENTS page
Rotate the menu control knob to align the pointer with the
desired page indication then push on the menu control knob.

20

Menus

To reset a changed value
If you press the STATUS/ CANCEL switch toward
CANCEL before pushing on the menu control knob, the
setting will be returned to its previous value.
To interrupt settings
Set the DISPLAY/MENU switch to OFF to turn off the
menu screen display.
The setting operation can be restarted by setting the
DISPLAY/MENU switch back to MENU.

If the screen can be scrolled, arrows will
indicate the direction for scrolling.
CONTENTS

Pointer

00

TOP

01.
02.<'!'IND>
03.
04.
05.
06.
07.
08.
09.
10.

3

The selected page is displayed.

Push on the menu control knob.
The question mark will change back to the pointer, and the
new setting will be registered.

Page number

4

VF DETAIL :
CRISP
:
FREQUENCY:
FAT MODE :

04 TOP
ON
0
9M
OFF

25%

To change the displayed page

1

Check that the pointer is located at the left of the page
number then push on the menu control knob.
The pointer changes to a flashing question mark.


VF DETAIL :
CRISP
:
FREQUENCY:
FAT MODE :

2

To specify a character string
When you press the menu control knob with the pointer
pointing to an item for which a character string, such as a file
ID, is to be specified, a cursor and the list of selectable
characters are displayed.
The displayed cursor can be moved by rotating the menu
control knob.

1

flash

? 04 TOP
ON
0
9M
OFF

25%

2

Rotate the menu control knob to flip through the
pages, and push on the knob when the desired page
is displayed.
The question mark will change back to the pointer, and
operations with the displayed page are enabled.

To return to the TOP MENU screen
Align the pointer with “TOP” at the top right of the menu
page then push on the menu control knob.

VF DETAIL :
CRISP
:
FREQUENCY:
FAT MODE :

04 TOP
ON
0
9M
OFF

25%

To set the Menu Items
If a question mark is flashing at the left of the page number,
push on the menu control knob to change it to the pointer.
Operation on the displayed page is enabled.

1
2

Align the pointer with the desired item, then push on
the menu control knob.
The pointer will change to a flashing question mark.
Rotate the menu control knob to change the setting
value.
When the knob is rotated quickly, the values will change
quickly; when rotated slowly, the values will change slowly.

To change other setting items on the same menu
page, repeat steps 1 through 3.

3

Set the cursor to the position where you wish enter a
character, then push on the menu control knob.
Another cursor appears on the character list.
Set the cursor to the character to be entered and push
on the menu control knob.
Repeat steps 1 and 2.
• By selecting INS on the line below the character list, you
can enter a space at the cursor position.
• Selecting DEL deletes the character at the cursor
position.
• You can return to step 1 without changing the character
by selecting RET.
• If you enter the permitted maximum number of
characters (up to the stop mark at the right end of the
line), the cursor moves to ESC on the line below the
character list.
Select END and push on the menu control knob.
The new string you have set is registered.
To restore the previous string, select ESC and push on
the menu control knob.

To end menu operations
Set the DISPLAY/MENU switch to OFF.

Editing the USER Menu
You can select desired pages and items from the
OPERATION, PAINT, MAINTENANCE, FILE, and
DIAGNOSIS menus and register them to the USER menu.
If you specify pages or items frequently used for the USER
menu, you can easily call and use them.
The following pages are included on the factory-set USER
menu:

Menus

21

Menu page title

If the USER MENU CUSTOMIZE menu has been used
before, the page last accessed appears.

USER menu Source menu / page No.
No.



U01

OPERATION

08



U02

OPERATION

04



U03

OPERATION

05



U04

OPERATION

01

<‘!’ IND>

U05

OPERATION

02



U06

OPERATION

03



U07

OPERATION

07



U08

OPERATION

06



U09

OPERATION

09



U10

OPERATION

10



U11

MAINTENANCE

M12



U12

OPERATION

17



U13

OPERATION

11



U14

OPERATION

12



U15

MAINTENANCE

M06



U16

MAINTENANCE

M08



U17

MAINTENANCE

M10



U18

MAINTENANCE

M11



U19

MAINTENANCE

M09



U20

MAINTENANCE

M13



U21

DIAGNOSIS

D03

2

If the CONTENTS page is displayed, turn the menu
control knob to move the pointer to any of USER 1
EDIT to USER 19 EDIT then push on the menu control
knob to display the page.
If a different page is displayed, turn the menu control
knob until the desired page appears then push on the
menu control knob to select the page.
Example: When you select the USER 2 EDIT page
USER 2 EDIT

E03 TOP

c

3

Move the pointer to the item to be added (this
operation is unnecessary if no item exists on the
page, as shown in the figure for the previous step)
then push on the menu control knob.
The EDIT FUNCTION screen appears.
EDIT FUNCTION

ESC

c INSERT

MOVE
DELETE
BLANK

For the items on each page, see “OPERATION Menu” (page
24), “MAINTENANCE Menu” (page 30), or “DIAGNOSIS
Menu” (page 34).
The USER MENU CUSTOMIZE menu allows you to configure
the USER menu as follows:
• Creating a new page with items selected from multiple menu
pages
• Adding (registering) a menu page (new page you create or
existing menu page) to the USER menu
• Deleting (unregistering) a page from the USER menu
• Changing the order of pages of the USER menu

4



1

CONTENTS

01.EDIT PAGE
02.USER 1 EDIT
2 EDIT
04.USER 3 EDIT
05.USER 4 EDIT
06.USER 5 EDIT
07.USER 6 EDIT
08.USER 7 EDIT
09.USER 8 EDIT
10.USER 9 EDIT

c 03.USER

22

5

Menus

Add the items.
1 Turn the menu control knob until the page that has the
desired items appears, then push on the menu control
knob.

Select USER MENU CUSTOMIZE on the TOP MENU
screen (page 20).
If this is the first time the USER MENU CUSTOMIZE
menu has been displayed, the CONTENTS page of the
menu appears.
xx

P01 ESC

FLARE
: c ON
GAMMA
: ON
BLK GAM : OFF
KNEE
: ON
WHT CLIP: ON
DETAIL : ON
LVL DEP : ON
SKIN DTL: OFF
MATRIX : OFF

To create a new page
While the EDIT page contains factory-preset items, the USER
1 EDIT to USER 19 EDIT pages are all blank in their initial
state. You can register up to 10 items, including blank lines, on
each of these pages.

Move the pointer to INSERT and push on the menu
control knob.
The page with the last item added appears.

2 Turn the menu control knob to move the pointer to the
desired item, then push on the menu control knob
The USER 2 EDIT page appears again, displaying the
newly added item.

E00 TOP

6

Add the remaining items by repeating steps 3 to 5.
You can add up to 10 items on one page.

To change the order of items on a page

1
2
3

2

Move the pointer to the item to be moved then push
on the menu control knob.
The EDIT FUNCTION screen appears.
Select MOVE then push on the menu control knob.
The previously displayed page appears again.

xx

Move the pointer to the position where you wish to
move the item then push on the menu control knob.
xx
c VF

ITEM MOVE
OUT

VF DETAIL

ESC

: OFF

: ON
: OFF
: OFF
:
1
z ASSIGNABLE1 : OFF

The item selected in step 1 moves to the position that you
selected in step 3.
In the above example, ASSIGNABLE1 is moved to the top,
and the other items are moved down one line.

3
4

2
3

02.USER
03.USER
04.USER
05.USER
06.USER
07.USER
08.USER
09.USER
10.USER

5

To delete, turn the menu control knob to move the
pointer to YES and push on the menu control knob.

To insert a blank line

1
2

Move the pointer to the item above which you wish to
insert a blank line.
The EDIT FUNCTION screen appears.
Select BLANK then push on the menu control knob.
The previously displayed page appears again, and a blank
line is inserted above the specified item.

Note

You cannot insert a blank line on a page where 10 items have
already been registered.

ESC

1
2
3
4
5
6
7
8
9
10

Move the pointer to the desired page then push on the
menu control knob.
This adds the number and name of the selected page
above the item selected in step 3.
To cancel addition of a page
Before pushing the menu control knob in step 5, turn the
menu control knob to move the pointer to ESC at the top
right of the screen then push on the menu control knob.
The EDIT PAGE screen appears again.

To delete a page from the USER menu

1

2

To add a page to the USER menu

1

Select INSERT then push on the menu control knob.
The selection screen appears.
CONTENTS

Move the pointer to the item to be deleted then push
on the menu control knob.
The EDIT FUNCTION screen appears.
Select DELETE and push on the menu control knob.
The previously displayed page appears again, and the
message “DELETE OK? YESbNO” appears.

E01 TOP

Move the pointer to the position where you wish to
add the page then push on the menu control knob.
The EDIT FUNCTION screen appears.

xx
c 01.USER

To delete items from a page

1

EDIT PAGE

01.
c 02.
03.
04.
05.<'!' IND>
06.
07.
08.
09.
10.

: COLOR

MARKER
CURSOR
ZEBRA SW

If the CONTENTS page is displayed, turn the menu
control knob to move the pointer to EDIT PAGE then
push on the menu control knob to display the EDIT
PAGE screen.
If a different page is displayed, turn the menu control
knob until the EDIT PAGE screen appears then push
on the menu control knob to select the page.

On the EDIT PAGE screen of the USER MENU
CUSTOMIZE menu, move the pointer to the page to be
deleted and push on the menu control knob.
The EDIT FUNCTION screen appears.
Select DELETE then push on the menu control knob.
The previously displayed page appears again, and the
message “DELETE OK? YESbNO” appears.
ITEM DELETE
ESC
DELETE OK? YES c NO
01.
02.
03.
z 04.
05.<'!' IND>
06.
07.
08.
09.
10.

Select USER MENU CUSTOMIZE on the TOP MENU
screen.
If this is the first time the USER MENU CUSTOMIZE
menu has been displayed, the CONTENTS page of the
menu appears. If the menu has been used before, the
page last accessed appears.

3

To delete, turn the menu control knob to move the
pointer to YES then push on the menu control knob.

Menus

23

To change the order of pages on the USER
menu

1

2
3

Display the EDIT PAGE screen of the USER MENU
CUSTOMIZE menu. Turn the menu control knob to
move the pointer to the page that you wish to move.
The EDIT FUNCTION screen appears.
Select MOVE then push on the menu control knob.
The EDIT PAGE screen appears again.
Move the pointer to the position where you wish to
move the page then push on the menu control knob.
xx

ITEM MOVE

ESC

01.
02.
03.
c 04.
05.<'!' IND>
06.
07.
08.
z 09.
10.

The page selected in step 1 is moved to the position
selected in step 3.
In the above example,  moves to the
“04” position, and the  and following pages
move down one line.

24

Menus

OPERATION Menu
Note

These remarks are common for all the following menu tables.
ON, OFF, 0, ... , in the Settings columns: Default settings
Page No. nn (Unn): For the pages that have been registered
on the USER menu at the factory, the USER menu page
numbers are indicated in parenthesis.
Execute by ENTER: Execute by pushing on the menu control
knob.
Page title
Page No.

Item

Settings


01(U04)

EX

ON, OFF

ZOOM
DISP

ON, OFF
LEFT, RIGHT

FOCUS
Valid only when a
serial lens is
used

ON, OFF

ND

ON, OFF

5600K

ON, OFF

IRIS

ON, OFF

WHITE

ON, OFF

GAIN

ON, OFF

SHUTT

ON, OFF

BATT

ON, OFF

RETURN

ON, OFF

TALK

ON, OFF

MESSAG

ALL, WRN, AT, OFF
ALL: To display all
messages
WRN: To display
warning messages
and higher
AT: To display Auto
Setup information and
higher

Page title
Page No.

Item

<'!' IND>
02 (U05)

[IND]: Activate/deactivate the '!' indication (page
11).
[NORMAL]: Specify the conditions under which
the ‘!’ indication is not to be displayed even if
[IND] is ON. (By specifying the standard or
normal conditions here, non-standard or
abnormal conditions can be found with the ‘!’
indication on the viewfinder.)
ND

Settings

Page title
Page No.

Item


03 (U06)

MARKER

[IND] ON, OFF
SAFETY ZONE

ON, OFF

EFFECT

ON, OFF, (FOCUS)
(FOCUS): Displayed
when INDICATOR of
 is
ON.

ASPECT

ON, OFF

80.0, 90.0, 92.5, 95.0%

[IND] ON, OFF, - - - - - : with CCU
connected

[IND] ON, OFF, - - - - - : with CCU
connected

16:9, 15:9, 14:9, 13:9, 4:3

[NORMAL] ON, OFF
GAIN

MASK

[IND] ON, OFF, - - - - - : with CCU
connected
SAFETY
For the safety
marker in
Aspect mode

[IND] ON, OFF, - - - - - : with CCU
connected

[IND] ON, OFF
[NORMAL] AUTO1,
AUTO2, MIN, MAX

EXT

[IND] ON, OFF

FORMAT

[IND] ON, OFF
[NORMAL]
UC model:
59.94i, 59.94P, 50i, 50P
CE model:
59.94i, 59.94P, 50i, 50P

ON, OFF, (AREA)
(AREA): Displayed when
AREA MARKER of
 is
ON.
80.0, 90.0, 92.5, 95.0%

[NORMAL] ON, OFF
FAN

ON, OFF
0 to 15 12
Set the level to darken
outside the aspect area.

[NORMAL] L, M, H
(combination allowed)
SHUTT

ON, OFF
1, 2, 3, 4
1: Entire cross
2: Entire cross with a
hole
3: Center
4: Center with a hole

[NORMAL] P, A, B
(combination allowed)
5600K

ON, OFF
WHITE, BLACK, DOT

CENTER

[NORMAL] 1, 2, 3, 4
(combination allowed)
WHITE

Settings


04 (U02)

VF DETAIL

ON, OFF
0 to 100% 25%

CRISP

–99 to +99 0

FREQUENCY

9M, 14M, 18M

FAT MODE

ON, OFF

FLICKER

ON, OFF

AREA

100%, 70%, 60%, 50%,
40%

ZOOM LINK

0%, 25%, 50%, 75%,
100%

COLOR DETAIL

ON, OFF
BLUE, RED, YELLOW

PEAK COLOR

ON, OFF

CHROMA
LEVEL

100%, 50%, 25%, 0%

Menus

25

Page title
Page No.

Item

Settings

Page title
Page No.

Item


05 (U03)

INDICATOR

ON, OFF, (EFFECT)
(EFFECT): Displayed
when EFFECT of  is ON.


09 (U09)

GAIN

MODE

BOX, B&W, COL

[H]: –3, 0, 3, 6, 9, 12 dB
ASSIGNABLE 1

UC model:
OFF, RETURN1 SW,
RETURN2 SW, INCOM,
VF DETAIL, MIX VF,
5600K, FAN MAX
CE model:
OFF, RETURN1 SW,
RETURN2 SW, ENG,
PROD, VF DETAIL, MIX
VF, 5600K, FAN MAX

ASSIGNABLE 2

UC model:
OFF, RETURN1 SW,
RETURN2 SW, INCOM,
VF DETAIL, MIX VF,
5600K, FAN MAX
CE model:
OFF, RETURN1 SW,
RETURN2 SW, ENG,
PROD, VF DETAIL, MIX
VF, 5600K, FAN MAX

ASSIGNABLE
REAR

UC model:
OFF, RETURN1 SW,
RETURN2 SW, INCOM,
VF DETAIL, MIX VF,
5600K, FAN MAX,
MARKER, CURSOR, VF
SCAN
CE model:
OFF, RETURN1 SW,
RETURN2 SW, ENG,
PROD, VF DETAIL, MIX
VF, 5600K, FAN MAX,
MARKER, CURSOR, VF
SCAN

1 to 5 3
QUICK, SMOOTH

GAIN

0 to 99 50

OFFSET

0 to 99 50

AREA MARKER


06 (U08)

SIZE

SMALL, MIDDLE, LARGE

POSITION

LEFT, CENTER, RIGHT

POSITION H

0 to 99 0

POSITION V

0 to 99 0

ZEBRA

WIDTH


08 (U01)

26

Menus

ON, OFF
1, 2, 1&2

ZEBRA1 LEVEL


07 (U07)

ON, OFF, (ASPECT)
(ASPECT): Displayed
when ASPECT
SAFETY of  is ON.

50 to 109% 70
0 to 30% 10

ZEBRA2

50 to 109% 100

CURSOR

ON, OFF
WHITE, BLACK, DOT

BOX/CROSS

BOX, CROSS

H POSITION

0 to 99 50

V POSITION

0 to 99 50

WIDTH

0 to 99 50

HEIGHT

0 to 99 50

VF OUT

COLOR, Y, R, G, B

RET MIX VF

ON, OFF

MIX DIRECTION

MAIN, RET

MIX VF MODE

Y-MIX, WIRE(W), WIRE(B)

MIX VF LEVEL

0 to 80%

VF SCAN

16:9, 4:3

[L]: –3, 0, 3, 6, 9, 12 dB
[M]: –3, 0, 3, 6, 9, 12 dB

BOTTOM, LEFT, TOP,
RIGHT
LEVEL

Settings

RE.ROTATION
STD, RVS
STD: Clockwise rotation
Specify operation
moves the pointer
mode of the
down or increases
menu control
values on the menu
knob on the front.
screen.
RVS: Counterclockwise
rotation moves the
pointer down or
increases values on
the menu screen.

Page title
Page No.

Item

Settings

Page title
Page No.

Item

Settings


10 (U10)

LENS VTR S/S
Assign a function
to the VTR
START/STOP
switch on the
mounted lens.

UC model:
OFF, RETURN1 SW,
RETURN2 SW, INCOM
CE model:
OFF, RETURN1 SW,
RETURN2 SW, ENG,
PROD


14

TRACKER
RECEIVE SELECT

SEPARATE, MIX

FRONT RET2
HANDLE SW1

HANDLE SW2

ZOOM SPEED

11 (U13)

INTERCOM MIC
LEVEL

UC model:
OFF, RETURN1 SW,
RETURN2 SW, INCOM,
ZOOM(T)
CE model:
OFF, RETURN1 SW,
RETURN2 SW, ENG,
PROD, ZOOM(T)
UC model:
OFF, RETURN1 SW,
RETURN2 SW, INCOM,
ZOOM(W)
CE model:
OFF, RETURN1 SW,
RETURN2 SW, ENG,
PROD, ZOOM(W)


15

00 to 99 20
DYNAMIC, CARBON,
MANUAL

–60,–40, –20 dB, (–n dB)
Settings in ( ): With
DYNAMIC or
CARBON (cannot be
changed)

–6, 0, +6 dB
Input gain
POWER

UNBAL

ON, OFF, (ON), (OFF)
Settings in ( ): With
DYNAMIC or
CARBON (cannot be
changed)
ON, OFF, (ON), (OFF)
Settings in ( ): With
CARBON (cannot be
changed)


12 (U14)

SIDE TONE

MU, 1 to 99, 50


13

INTERCOM
RECEIVE SELECT

SEPARATE, MIX

INTERCOM
UC model
only

RIGHT, LEFT, BOTH, - - -

ENG
CE model
only

RIGHT, LEFT, BOTH, - - -

PROD
CE model
only

RIGHT, LEFT, BOTH, - - -

PGM1

RIGHT, LEFT, BOTH, - - -


16
See FILE menu
F01.


17 (U12)

INTERCOM
UC model
only

RIGHT, LEFT, BOTH, - - -

TALK
CE model
only

RIGHT, LEFT, BOTH, - - -

ENG
CE model
only

RIGHT, LEFT, BOTH, - - -

PROD
CE model
only

RIGHT, LEFT, BOTH, - - -

PGM1

RIGHT, LEFT, BOTH, - - -

PGM2

RIGHT, LEFT, BOTH, - - -

EARPHONE
RECEIVE SELECT
INTERCOM
UC model
only

RIGHT, LEFT, BOTH, - - -

ENG
CE model
only

RIGHT, LEFT, BOTH, - - -

PROD
CE model
only

RIGHT, LEFT, BOTH, - - -

PGM1

RIGHT, LEFT, BOTH, - - -

PGM2

RIGHT, LEFT, BOTH, - - -

TRACKER

RIGHT, LEFT, BOTH, - - -

READ (MS→CAM)

RIGHT, LEFT, BOTH, - - -

TRACKER

RIGHT, LEFT, BOTH, - - -

Execute by ENTER.

WRITE (CAM→MS) Execute by ENTER.
PRESET

Execute by ENTER.

FILE ID

Max.16 characters

CAM CODE

Display only

DATE

Display only

FILE

1 to 17:
1 to 16: When using a
non-serial lens
17: When using a serial
lens
Lens file name
Changeable only when
using a non-serial lens
F number (iris open) of the
lens
Changeable only when
using a non-serial lens

CENTER MARKER
To set and store the center marker position.
H POS

PGM2

SEPARATE, MIX

–20 to +20 0
Increasing the value
moves it to the right.

V POS

–20 to +20 0
Increasing the value
moves it downwards.

STORE

Execute by ENTER.

Menus

27

Page title
Page No.

PAINT Menu
Page title
Page No.

Item


P01

FLARE

ON, OFF

GAMMA

ON, OFF

BLK GAM

ON, OFF


Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2009:02:16 15:33:15Z
Creator Tool                    : FrameMaker 7.1
Modify Date                     : 2009:02:17 15:16:57+09:00
Metadata Date                   : 2009:02:17 15:16:57+09:00
Format                          : application/pdf
Title                           : HXC-100
Creator                         : Sony Corporation
Document ID                     : uuid:8bde8f6a-7be7-4296-adcf-f656d4a38030
Instance ID                     : uuid:ccc63383-ccb7-4483-9cd0-314ad7fb10a8
Page Count                      : 41
Author                          : Sony Corporation
EXIF Metadata provided by EXIF.tools

Navigation menu