Sony VPL VW885ES VW760ES/VW885ES User Manual Operating Instructions 4732479111
User Manual: Sony VPL-VW885ES Operating Instructions
Open the PDF directly: View PDF .
Page Count: 54
Download | ![]() |
Open PDF In Browser | View PDF |
4-732-479-11 (1) Video Projector Operating Instructions Before operating the unit, please read this manual, supplied Quick Reference Manual and Safety Regulations thoroughly, and retain them for future reference. VPL-VW760ES VPL-VW885ES © 2017 Sony Corporation Table of Contents Location of Controls Error Handling Front/Right Side .......................................................... 3 Rear/Left Side/Bottom ................................................ 4 Remote Control ........................................................... 5 Troubleshooting ........................................................ 34 About Indicators ........................................................ 36 Message Lists ............................................................ 37 Connections and Preparations Others Installing the Unit ....................................................... 6 Adjusting the Picture Position .................................... 6 Connecting to Video Equipment or a Computer ....... 10 Updating the Software .............................................. 38 About HDR (high dynamic range) ............................ 38 About the Simulated 3D Feature ............................... 38 NOTICES AND LICENSES FOR SOFTWARE USED IN THIS PRODUCT .............................................. 38 Specifications ............................................................ 39 Preset Signals ....................................................... 40 Input Signals and Adjustment/Setting Items ....... 41 Compatible 3D Signals ........................................ 42 3D Signals and Adjustable/Setting Items ............ 42 Aspect Mode ........................................................ 43 Motionflow .......................................................... 44 Storage Conditions of Adjustment/Setting Items ................................................................. 45 Projection Distance and Lens Shift Range ................ 47 Dimensions ............................................................... 51 Projecting Projecting the Picture ................................................ 11 Turning Off the Power ......................................... 11 Watching 3D Video Images ...................................... 11 Using the 3D Glasses ........................................... 12 Using the Picture Position ......................................... 12 Selecting the Aspect Ratio According to the Video Signal ..................................................................... 13 Selecting the Picture Viewing Mode ......................... 15 Using the Menus Operation through the Menus ................................... 16 Picture Menu ............................................................. 18 Advanced Picture Menu ............................................ 22 Screen Menu ............................................................. 23 Setup Menu ............................................................... 25 Function Menu .......................................................... 26 Items Locked by Settings Lock ........................... 28 Installation Menu ...................................................... 29 Information Menu ..................................................... 31 About the Preset Memory .................................... 31 Using Network Features Displaying the Control Window of the Unit with a Web Browser .......................................................... 32 Operating the Control Window ................................. 33 Switching the Page ............................................... 33 Setting the Access Limitation .............................. 33 Confirming the Information Regarding the Unit ................................................................... 33 2 Location of Controls Front/Right Side Connectors Indicators Others a ON/STANDBY indicator (page 36) i Ventilation holes (intake) b WARNING indicator (page 36) j Remote control detector (page 6) Connectors c LAN connector (page 32) d HDMI 1/HDMI 2 connector (page 10) e TRIGGER 1/TRIGGER 2 connector (page 29) f IR IN connector Inputs the signals to control the projector. g REMOTE connector Connects to a computer, etc. for remote control. h USB connector (page 38) 3 Rear/Left Side/Bottom The buttons on the control panel function the same as those on the remote control. Control panel Control panel Others a [/1 (On/Standby) button (page 7) f Remote control detector (page 6) b INPUT button (page 11) g Ventilation holes (exhaust) c MENU button (page 16) h AC IN socket (page 7) d M/m/, (arrow)/ENTER button (page 16) i Projector suspension support attaching hole (page 52) e LENS button (page 6) j Front feet (adjustable) (page 8) k Ventilation holes (intake) 4 a LIGHT button Illuminates the buttons on the remote control. Remote Control b Infrared transmitter c ?/1 (On/Standby) button (page 7) d INPUT button (page 11) e CALIBRATED PRESET buttons (page 15) f LENS ADJUSTMENT buttons (page 7) g POSITION button (page 12) h RESET button (page 17) i M/m/, (arrow)/ (page 16) (enter) button j MENU button (page 16) k MOTIONFLOW button (page 19) l ASPECT button (page 13) m COLOR SPACE button (page 21) n COLOR TEMP button (page 19) o GAMMA CORRECTION button (page 20) p 3D button (page 11) q REALITY CREATION button (page 18) r ADVANCED IRIS button This function is not provided in this projector. s CONTRAST ENHANCER button (page 19) t SHARPNESS +/– button (page 20) u CONTRAST +/– button (page 19) v BRIGHTNESS +/– button (page 19) 5 Connections and Preparations Installing the Unit Adjusting the Picture Position The installation distance between the unit and a screen varies depending on the size of the screen or whether or not you use the lens shift features. Install this unit so that it fits the size of your screen. For details on the distance between the unit and the screen (the projection distance) and the size of projected video, see “Projection Distance and Lens Shift Range” (page 47). 1 Project an image on the screen and then adjust the picture position. Position the unit so that the lens is parallel to the screen. Top view Screen Remote control detector 2 Tips • The ?/1 (On/Standby), INPUT, and MENU buttons on the side panel of the unit have the same functions as those on the remote control. The M/m/, (arrow)/ENTER button of the unit has the same function as the M/m/, (arrow)/ (enter) button on the remote control. The LENS button functions the same way as the LENS ADJUSTMENT (FOCUS, ZOOM, SHIFT) buttons on the remote control. • When adjusting the lens, each time you press the LENS button on the unit, the lens adjustment function switches between “Lens Focus,” “Lens Zoom” and “Lens Shift.” Project an image on the screen and adjust the picture so that it fits the screen (page 6). Note When using a screen with an uneven surface, stripes pattern may rarely appear on the screen depending on the distance between the screen and the unit or the zooming magnifications. This is not a malfunction of the unit. Note Depending on the installation location of the unit, you may not be able to control it with the remote control. In this case, point the remote control at the remote control detector of the unit or the screen. 6 1 4 After connecting the AC power cord to the unit, plug the AC power cord into a wall outlet. The ON/STANDBY indicator lights in red and the unit goes into standby mode. Adjust the picture size. Press the LENS ADJUSTMENT (ZOOM) button to display the Lens Zoom adjustment window (test pattern). Then adjust the size of the picture by pressing the M/m/, button. Lights in red. 2 Press the ?/1 (On/Standby) button to turn on the unit. The ON/STANDBY indicator flashes in green, and then lights in green. Flashes in green for tens of seconds and then lights in green. 3 To make the picture larger, press M/,. To make the picture smaller, press m/<. Adjust the focus. Press the LENS ADJUSTMENT (FOCUS) button to display the Lens Focus adjustment window (test pattern). Then adjust the focus of the picture by pressing the M/m/, button. 5 Tips • When “Lens Control” is set to “Off” on the Installation menu, you cannot adjust the focus, the picture size or the proper position by pressing the FOCUS, ZOOM or SHIFT button (page 29). • When “Test Pattern” is set to “Off” on the Function menu, the test pattern is not displayed (page 27). Adjust the picture position. Press the LENS ADJUSTMENT (SHIFT) button to display the Lens Shift adjustment window (test pattern). Then adjust to the proper position of the picture by pressing the M/m/, button. Tip Whenever you press the button, the test pattern disappears. Note When adjusting the picture position, do not touch the lens unit, otherwise your fingers may be pinched by the moving parts. Note Adjust the lens by using buttons on the remote control or the control panel of the unit. Never make adjustments by directly turning the lens with your hands, which may cause damage or malfunction to the unit. 7 To adjust the horizontal position Note The range to move the picture projected on the screen can be adjusted only within the octagon area illustrated below. For details, see “Projection Distance and Lens Shift Range” (page 47). Press ,. The picture projected on the screen moves right or left by a maximum of 31% of the screen width from the center of the lens. Range of movement of the projected picture 0.85V Top view 31% 1 screen width 31% 0.31H 0.31H Projected Picture 0.8V H: Width of the projected picture V: Height of the projected picture : Picture position when moving the picture to the left at maximum : Picture position when moving the picture to the right at maximum Press the RESET button on the remote control while the Lens Shift adjustment window is displayed, the horizontal position returns to the center of the lens (factory default position). The zoom and focus are not changed. To adjust the tilt of the installation surface If the unit is installed on an uneven surface, use the front feet (adjustable) to keep the unit level. To adjust the vertical position Press M/m. The picture projected on the screen moves up by a maximum of 85% or moves down by a maximum of 80% of the screen height from the center of the lens. Turn to adjust. Front feet (adjustable) Side view Notes • If the unit is tilted up or down, the projected image may be trapezoidal. • Be careful not to catch your finger when turning the front feet (adjustable). 85% 1 screen height 80% : Picture position when moving the picture upward at maximum : Picture position when moving the picture downward at maximum 8 Lens adjustment window (test pattern) 1.78:1 (16:9) 1.33:1 (4:3) 2.35:1 1.85:1 The dashed lines show the screen sizes of each aspect ratio. 9 Connecting to Video Equipment or a Computer You can enjoy high picture quality by connecting a DVD player/recorder, Blu-ray Disc player/recorder, or PlayStation® equipped with HDMI output to the HDMI input of the unit. When making connections, be sure to do the following: • Turn off all equipment before making any connections. • Use the proper cables for each connection. • Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cable itself. • Refer to the operating instructions of the connected equipment. Computer Right side of the unit Equipment with HDMI output connectors to HDMI input AV amplifier Speakers to HDMI output HDMI cable (not supplied) : Video signal flow Use a High Speed or Premium High Speed HDMI cable on which the cable type logo is specified. Notes • Use a High Speed or Premium High Speed HDMI cable. With a standard HDMI cable, images of 1080p, DeepColor, 3D video and 4K video may not be displayed properly. • When connecting an HDMI cable to the unit, make sure the V mark on the upper part of the HDMI input of the unit and the v mark on the connector of the cable are faced at each other. • If the picture from equipment connected to the unit with an HDMI cable is not correct, check the settings of the connected equipment. • If you set your computer, such as a notebook type, to output the signal to both computer’s display and this equipment, the picture of the equipment may not appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the computer’s operating instructions supplied with your computer. For settings of the computer, consult with the manufacturer of the computer. 10 . Projecting Projecting the Picture 1 Watching 3D Video Images Turn on both the unit and the equipment connected to the unit. 2 Press INPUT to display the input palette on the screen. 3 Select the equipment from which you want to display images. Press INPUT repeatedly or press M/m/ (enter) to select the equipment from which to project. You can enjoy powerful 3D video images, such as from 3D games and 3D Blu-ray Discs, using the optional Active 3D Glasses (TDG-BT500A). Tips • When “Status” is set to “Off” on the Setup menu, the input palette does not appear. Press the INPUT button to switch between input terminals sequentially. • You can change the language for the menu and on-screen displays in “Language” on the Setup menu (page 25). Turning Off the Power 1 Press the ?/1 (On/Standby) button. The message “POWER OFF?” appears. 2 Press the ?/1 (On/Standby) button again before the message disappears. The ON/STANDBY indicator flashes in green and the fan continues to run to reduce the internal heat. 1 Turn on the HDMI equipment for 3D compatibility connected to the unit, then play the 3D content. For details on how to play 3D content, refer to the operating instructions for the connected equipment. 2 Turn on the unit and project the 3D video image. For details on how to project the image, see “Projecting the Picture” (page 11). 3 Turn on the 3D glasses, and then put them on so that they fit comfortably. For details on how to use the 3D glasses, see “Using the 3D Glasses” (page 12). Tip The factory default setting for “2D-3D Display Sel.” is “Auto” to allow projecting 3D video images automatically when the unit detects 3D signals. Notes • It may not be possible to display 3D video image, depending on the type of signal. Set the “2D-3D Display Sel.” to “3D,” and “3D Format” to “Side-by-Side” or “Over-Under” to suit the format of the 3D content you want to watch (page 26). • Use the 3D glasses within the communication range (page 12). • There are differences in perception of 3D video images among individuals. • When the temperature of the usage environment is low, the 3D effect may be diminished. The fan stops and the ON/STANDBY indicator changes from flashing green to remaining red. The power is turned off completely, and you can disconnect the AC power cord. Adjusting/Setting the 3D functions Note Never disconnect the AC power cord while the indicator is flashing. You can adjust/set the 3D functions by pressing the 3D button on the remote control or with the “3D Settings” of the Function menu. For details, see “3D Settings” (page 26). Tip You can turn off the unit by holding the ?/1 (On/Standby) button for about 1 second, instead of performing the above steps. 11 Using the 3D Glasses 1 2 3 Using the Picture Position Turn on the 3D glasses, and register them on the unit. For details on how to register the 3D glasses, refer to the operating instructions supplied with the 3D glasses. You can store up to five combinations of lens settings (focus, picture size, picture position), aspect ratio, and blanking. These settings can be recalled. In the factory preset setting, the Picture Position is not stored. Put on the 3D glasses. Turn toward the screen. 1 Precautions for use Misoperation may occur if: • The viewing position is too far from the projector • There are other communication devices, such as a wireless LAN (IEEE802.11 b/g/n) or a microwave with a bandwidth of 2.4 GHz, near the unit 3D glasses communication range The Picture Position selecting palette is displayed. The following figure indicates the communication range of the 3D glasses. If you try to watch 3D video images from a distance greater than the communication range or install the unit outside the communication range, the 3D glasses may not be able to display the images properly. Also, the distance varies depending on the environment of the room and installation environment of the unit. 2 Top or side view Projector 10 m 10 m Press POSITION. 10 m 10 m 12 Press POSITION repeatedly, or press M/m/ to select the position. The settings of the position selected is recalled. Store or delete lens settings, aspect ratio, and blanking in the “Picture Position” of the Screen menu (page 23). The position where the lens settings, aspect ratio, and blanking are not stored is displayed as “---.” Image of the lens moving In the example below, the images with aspect ratio of 1.78:1 (16:9) and 2.35:1 are projected on a 2.35:1 screen. Selecting the Aspect Ratio According to the Video Signal You can select an aspect ratio best suited for the video signal received. When a 1.78:1 (16:9) image is input Press ASPECT. Each time you press the button, you can select the “Aspect” setting.You can also select it using the menu (page 23). When a 2.35:1 image is input Press the POSITION button. ASPECT button The 2.35:1 image expands to fill the screen. Notes Original image • After you have selected and confirmed the lens position, the lens starts to move. Do not touch, or place anything near, the lens, otherwise it may cause injury or a malfunction. • If you press any button on the remote control or the unit while the lens is moving, the lens stops. In this case, select the lens position again or adjust the lens manually. • The Picture Position function is not guaranteed to reproduce the lens settings precisely. • When you use the subtended screen angle of two or more aspects using lens zoom, install the unit within the specified parameters referring to “Projection distance” (page 48). With some setting positions, the range of lens shift may be restricted, even though the unit is installed within the specified parameters. Recommended setting and resultant images 1.85:1 Zoom 1.85:1 Squeezed 1.85:1 2.35:1 Zoom 2.35:1 Squeezed 2.35:1 13 Original image Notes on switching the “Aspect” setting • Select the aspect mode taking into account that changing the aspect ratio of the original picture will provide a different look from that of the original image. • Note that if the unit is used for profit or for public viewing, modifying the original picture by switching the aspect may constitute an infringement of the rights of authors or producers, which are legally protected. Recommended setting and resultant images Normal 1.78:1 (16:9) 1.33:1 (4:3) 1.33:1 (4:3) with side panels V Stretch 2.35:1 When using an anamorphic lens Squeeze 16:9 When using an anamorphic lens Stretch Squeezed Note Selectable aspect modes vary depending on the input signal (page 43). 14 Selecting the Picture Viewing Mode You can select the picture viewing mode that best suits the type of video source or room conditions. You can save and use different preset modes for 2D/3D respectively. Press one of the CALIBRATED PRESET buttons. CALIBRATED PRESET buttons Setting items Description CINEMA FILM 1 Picture quality suited to reproducing the highly dynamic and clear images typical of master positive film. CINEMA FILM 2 Picture quality suited to reproducing the rich tone and color typical of a movie theater, based on the “CINEMA FILM 1.” REF A picture quality setup suitable for when you want to reproduce faithfully the original image quality, or for enjoying image quality, without any adjustment. TV Picture quality suited for watching TV programs, sports, concerts, and other video images. PHOTO Ideal for projecting still images taken with a digital camera. GAME Picture quality suited to gaming, with wellmodulated colors and fast response. Picture quality suited for watching movies in a bright environment, such as a living room. Picture quality suited for watching TV programs, sports, concerts, and other video images in a bright environment, such as a living room. BRT CINE BRT TV USER Adjusts the picture quality to suit your taste then saves the setting. The factory default setting is the same as “REF.” 15 Using the Menus Note The menu displays used for the explanation may be different from the actual menu display. Pop-up menu Operation through the Menus Setting items The unit is equipped with an on-screen menu for making various adjustments and settings. If you select an item name followed by an arrow (B), the next menu window with setting items appears. 1 Press MENU. The menu window appears. Setting menu 2 Adjustment menu Press M/m to select a menu item, and press , or . The items that can be set or adjusted with the selected menu appear. The item presently selected is shown in white. Next menu window Setting items 3 Press M/m to select an item you want to set or adjust and press , or . The setting items are displayed in a pop-up menu, in a setting menu, in an adjustment menu or in the next menu window. 16 4 Make the setting or adjustment of an item. When changing the adjustment level Press M/, to increase the value, and press m/< to decrease the value. Press to store the setting and restore the original menu screen. When changing the setting Press M/m to change the setting. Press to restore the original screen. You can restore the original screen using < depending on the selected item. To clear the menu Press MENU. To reset the picture that has been adjusted Select “Reset” from the Picture menu. When the screen display appears, select “Yes” using < and press . All of the following settings are reset to its factory preset value: “Reality Creation,” “Cinema Black Pro,” “Motionflow,” “Contrast,” “Brightness,” “Color,” “Hue,” “Color Temp.,” “Sharpness,” and “Expert Setting” on the Picture menu To reset the items that have been adjusted Select an item in the menu screen, and display the pop-up menu, the setting menu, or the adjustment menu. Press RESET on the remote control to reset only the selected settings to its factory preset value. Note The RESET button on the remote control is available only when the adjustment menu or the setting menu is selected. 17 Picture Menu The Picture menu is used for adjusting the picture. Note These items may not be adjustable or configurable, depending on the type of input signal. For details, see “Input Signals and Adjustment/Setting Items” (page 41). Item names in brackets represent those printed on the remote control. Setting items Description Calib. Preset [CALIBRATED PRESET] You can select the picture viewing mode that best suits the type of video source or the environment. You can save and use different preset modes for 2D/3D respectively. Cinema Film 1: Picture quality suited to reproducing the highly dynamic and clear images typical of master positive film. Cinema Film 2: Picture quality suited to reproducing the rich tone and color typical of a movie theater, based on the Cinema Film 1. Reference: A picture quality setup suitable for when you want to reproduce faithfully the original image quality, or for enjoying image quality, without any adjustment. TV: Picture quality suited for watching TV programs, sports, concerts, and other video images. Photo: Ideal for projecting still images taken with a digital camera. Game: Picture quality suited to gaming, with well-modulated colors and fast response. Bright Cinema: Picture quality suited for watching movies in a bright environment, such as a living room. Bright TV: Picture quality suited for watching TV programs, sports, concerts, and other video images in a bright environment, such as a living room. User: You can adjust the picture quality to suit your taste, and save the setting. The factory default setting is the same as “Reference.” Tip Any adjustments to picture quality settings are saved for each input. Reset Resets all currently selected Calib. Preset mode settings to their default values (page 17). Tip Reset does not affect settings saved for items of “Color Temp.” Reality Creation [REALITY CREATION] Adjusts the detail and noise processing of images. (Super-resolution function) On: Adjusts the settings of “Reality Creation.” Database: Select “Normal” or “Mastered in 4K.” “Mastered in 4K” provides image quality suitable for Blu-ray Disc™ “Mastered in 4K” releasing from Sony Pictures Home Entertainment. Resolution: When you increase the setting value, the texture and detail of the picture become sharper. Noise Filtering: When you increase the setting value, the noise (picture roughness) becomes less prominent. Test: On/Off: Changes “On” and “Off” at a certain frequency to check the effect of “Reality Creation.” Tip The display position of status during the test works together with the “Menu Position” setting (page 25). Off: The “Reality Creation” function is not applied. 18 Setting items Description Cinema Black Pro Laser Light Setting Dynamic Control: Adjusts the range of movement of the laser light control. Full: Automatically optimizes the laser light control and signal processing according to the brightness level of the input source. This results in a bright and high contrast image. Limited: Suppresses the movement and brightness of the laser light control, making the picture quality suitable for viewing in a dark room. Off: The “Dynamic Control” function is not applied. Output: The higher the setting, the brighter the picture. The lower the setting, the darker the picture. Tip Adjust “Output” according to the brightness of the picture. Contrast Enhancer Corrects the level of bright and dark parts automatically to optimize contrast according to a scene. [CONTRAST ENHANCER] Increases image sharpness and makes image dynamic. High/Middle/Low: You can adjust the contrast enhancer. Off: The contrast enhancer function is not applied. Motionflow [MOTIONFLOW] Impulse: Reproduces original picture quality. Provides cinema-like picture, which may flicker. Combination: Reduces motion blur while maintaining brightness for high-speed picture content. Smooth High: Provides smoother picture movement; especially effective for film-based content. Smooth Low: Provides smoother picture movement for standard use. True Cinema: Images, such as a movie created in 24 frames per second, are reproduced at the original framerate. Off: The “Motionflow” function is not applied. Tips • Select “Off” if the selected “Smooth High,” “Smooth Low,” “Impulse,” “Combination,” or “True Cinema” results in a distorted picture. • Depending on the picture content, you may not see the effect visually even if you have changed the settings. • Only “Off” or “Impulse” is available when a signal with a resolution of 4096 × 2160 is input. Contrast [CONTRAST] Adjusts the contrast. Higher values increase the sharpness in images, while lower values decrease the sharpness. You can make adjustments by pressing the CONTRAST +/- button on the remote control. When the HDR signal is input with “HDR10,” “HDR Reference,” “HLG,” or “Auto” set for “HDR,” “Contrast(HDR)” appears instead of “Contrast.” Brightness [BRIGHTNESS] Adjusts the brightness of the picture. The higher the setting, the brighter the picture. The lower the setting, the darker the picture. You can make adjustments by pressing the BRIGHTNESS +/- button on the remote control. Color Adjusts the color density. The higher the setting, the greater the intensity. The lower the setting, the lower the intensity. Hue Adjusts the color tone. The higher the setting, the more greenish the picture becomes. The lower the setting, the more reddish the picture becomes. Color Temp. [COLOR TEMP] Adjusts the color temperature. D93: Equivalent to 9,300 K color temperature normally used in TVs. Gives white colors a blue tint. D75: Equivalent to 7,500 K color temperature used as an ancillary standard illuminant. Gives a neutral tint between “D93” and “D65.” D65: Equivalent to 6,500 K color temperature used as a standard illuminant. Gives white colors a red tint. D55: Equivalent to 5,500 K color temperature used as an ancillary standard illuminant. Gives white colors an even redder tint. Custom 1 to 5: Enables you to adjust, set, and store your favorite color temperature. The factory default settings are as follows. Custom 1: Same as the “D93” color temperature setting. Custom 2: Same as the “D75” color temperature setting. Custom 3: Same as the “D65” color temperature setting. Custom 4: Same as the “D55” color temperature setting. Custom 5: Setting that prioritizes brightness. Tip You can adjust each item to a color temperature according to your preference. 19 Setting items Description Sharpness [SHARPNESS] Sharpens the outline of the picture, or reduces the noise. The higher the setting, the sharper the picture. The lower the setting, the softer the picture, thus reducing the noise. You can make adjustments by pressing the SHARPNESS +/- button on the remote control. Expert Setting NR (Noise Reduction) Reduces the roughness or noise of the picture. Auto: Detects the noise level to reduce the roughness or noise of the picture automatically. High/Middle/Low: Select a setting according to the roughness or noise of the input signal source. Off: The NR (noise reduction) function is not applied. Tip The noise level may not be detected accurately with “Auto” depending on the input signal source. If the picture is unacceptable with “Auto,” select a setting from among “High,” “Middle,” “Low” or “Off.” MPEG NR (MPEG Noise Reduction) Reduces block noise and mosquito noise, particularly in digital signals. Auto: Detects the noise level to reduce the block noise and mosquito noise of the picture automatically. High/Middle/Low: Select a setting according to the block noise and mosquito noise of the input signal source. Off: The MPEG NR (MPEG noise reduction) function is not applied. Tip The noise level may not be detected accurately with “Auto” depending on the input signal source. If the picture is unacceptable with “Auto,” select a setting from among “High,” “Middle,” “Low” or “Off.” Smooth Gradation Smooths the gradation of the flat parts of images. High/Middle/Low: You can adjust the smooth gradation effect. Off: The smooth gradation function is not applied. Tip This item is not available for 3D signals. Film Mode According to the film source you have selected, make a setting for playback. Auto: Suitable for reproducing the original picture movement. Normally, set this to “Auto.” Off: Plays back the picture in progressive format without detecting video signals automatically. Tip This item is compatible with a 1080i signal only. Gamma Correction [GAMMA CORRECTION] Adjusts the response characteristics of the tone of the picture. Select a favorite tone from 10 options. 1.8: Bright Produces a brighter picture overall. 2 2.1 2.2 2.4 2.6: Dark Produces a darker picture overall. Gamma 7: Simulates the gamma curve of film. Gamma 8: Increases the sharpness in images. Select this when you watch in a bright environment, such as a living room. Gamma 9: Produces a brighter picture than Gamma 8. Gamma 10: Increases the sharpness in images. Select this when you watch TV programs, etc., in a bright environment, such as a living room. Off: The “Gamma Correction” function is not applied. Color Correction On: Adjusts Hue, Saturation and Brightness of the selected colors. Repeat steps 1 and 2 described below to specify the target color. 1 Press M/m to select “Color Select,” then press , to select the color you want to adjust among “Red,” “Yellow,” “Green,” “Cyan,” “Blue,” and “Magenta.” 2 Press M/m to select “Hue,” “Saturation” or “Brightness,” then adjust them to suit your taste using , while watching the projected picture. Off: The “Color Correction” effect is not applied. 20 Setting items Description Clear White Emphasizes vivid whites. High/Low: You can adjust the “Clear White” effect. Off: The “Clear White” effect is not applied. x.v.Color Set this item when connecting the unit with equipment that supports x.v.Color and playing back an x.v.Color video signal. On: You can play back an x.v.Color video signal. Off: The “x.v.Color” function is not applied. Tip Setting x.v.Color to “On” disables gamma adjustment. HDR Sets how to play back HDR content. Auto: Distinguishes HDR content automatically and applies the optimal picture quality. When an input signal supports BT.2020, the “Color Space” is set to “BT.2020” automatically. When a signal other than BT.2020 is input, the mode set in “Color Space” is applied. (“BT.2020” is not available in this case.) HDR10: Set when playing back HDR10-compatible content. HDR Reference: This mode is suitable for playing back HDR10-compatible content with a maximum brightness of 1,000 nit. HLG: Set when playing back HLG-compatible content. Off: Set when playing back content other than HDR content. All of the modes of “Color Space” are selectable when “HDR10,” “HDR Reference,” “HLG,” or “Off” is selected. Notes • If the setting is not correct for the input content, the bright and dark areas of the video may appear too bright or too dark. • When setting “HDR10” or “HDR Reference,” compare the picture quality in both modes, and select the one that optimally displays the average brightness and tone of the bright parts. Color Space [COLOR SPACE] Converts the color space. BT.709: An ITU-R BT.709 color space, which is used for high-definition television broadcast or Blu-ray Disc. The color space is equivalent to sRGB. BT.2020: The color space is wider than BT.709. Use this setting when playing back HDR content. Color Space 1: The color space suited for watching TV programs and video images, such as sports, concerts, etc. Color Space 2: The color space suited for watching TV programs, sports, concerts, and other video images in a bright environment, such as a living room. Color Space 3: The color space suited for watching movies in a bright environment, such as a living room. Custom: You can adjust the color space setting. Note When “HDR” is set to “Auto,” the selectable mode changes according to the signal type (page 21). Input Lag Reduction Reduces the delay of the display for a video. On: Shortens the time to display the input video image; effective for increasing the performance of the display reaction speed when using an external controller, etc. Off: Turns the Input Lag Reduction function off. Tip When “Input Lag Reduction” is set to “On,” “Motionflow” (settings other than “Impulse”), “NR,” and “MPEG NR” cannot be set. 21 Advanced Picture Menu You can adjust the gaps in color that have occurred after a long period of use. Notes • Auto Calibration results in relatively coarse calibration. The color settings are not guaranteed to be the same as the factory default values. • The colors are projected automatically while performing “Pre Check” or “Adjust.” This is not a malfunction. • Do not turn off the power or operate the remote control or control panel during “Pre Check” or “Adjust,” as the process may be canceled. Tips • dE is an indicator of changing color. The smaller the value of dE, the fewer the changes caused by the color. • Perform the calibration after the power has been on for more than 30 minutes. • It takes a few minutes for “Pre Check” or “Adjust” to complete. • When “Pre Check” or “Adjust” starts, the screen position may shift as the lens returns to its factory default position. After completion, the screen returns to its previous position automatically. • If the environment, such as the brightness of the room, changes while performing “Pre Check” or “Adjust”, measurement may be affected. • If the “Pre Check” or “Adjust” function fails, try it again. Setting items Description Auto Calibration Pre Check: Checks the color difference against the factory default settings, before calibration starts. Adjust: Performs Auto Calibration. Before/After: Toggles the factory default settings and the setting after the calibration at a certain frequency. You can check the effect of the calibration by monitoring the actual image. Reset: Resets the calibration results, and returns to the factory default settings. 22 Screen Menu You can set the picture size, aspect mode, etc. Note These items may not be available, depending on the type of input signal. For details, see “Input Signals and Adjustment/Setting Items” (page 41). Item names in brackets represent those printed on the remote control. Setting items Description Picture Position [POSITION] You can store up to five combinations of lens settings, aspect ratio, and blanking. After setting the lens (focus, picture size, picture position), select from “1.85:1,” “2.35:1,” “Custom 1,” “Custom 2,” or “Custom 3” depending on the subtended screen angle, and after confirming, continue by selecting “Save,” “Delete,” or “Select.” Save: Stores the current lens settings (focus, picture size, picture position) in the selected position. If a setting is already stored in that position, it is overwritten. Delete: Deletes the stored setting. After the setting is deleted, “1.85:1,” “2.35:1,” “Custom 1,” “Custom 2,” or “Custom 3” in the display change to “---.” Select: Recalls the settings of the selected position. Tips • The optimal aspect ratio is preset for each picture position. The aspect ratio can be changed and saved for each picture position. • When saving the Picture Position, temporarily move the picture from the saving point down 5 cm or more. Move the picture up again and save. This improves the precision of the Picture Position when calling it. Notes • After you have selected and confirmed the lens position, the lens starts to move. Do not touch the lens and the area around the lens, otherwise it may cause injury or a malfunction. • If you press any button on the remote control or the unit while the lens is moving, the lens stops. In this case, select the lens position again or adjust the lens manually. • When you use a 2.35:1 or a 16:9 subtended screen angle with the Picture Position function, make sure that the installation position is suitable (page 12). • The Picture Position function is not guaranteed to reproduce the lens settings precisely. Aspect [ASPECT] You can set the aspect ratio of the picture to be displayed for the current input signal (page 13). 1.85:1 Zoom: A 1.85:1 aspect ratio picture is displayed in its original aspect ratio, enlarged so that black bands do not appear at the top and bottom of the projection surface. 2.35:1 Zoom: A 2.35:1 aspect ratio picture is displayed in its original aspect ratio, enlarged so that black bands at the top and bottom of the projection surface are as small as possible. When you select “2.35:1 Zoom” from “Trigger Select 1/2” on the Installation menu, a 12 V signal is output from the TRIGGER 1 or TRIGGER 2 connector (page 29). Normal: Input video is displayed in its original aspect ratio, enlarged to fill the projection surface. This mode is suitable for viewing 1.78:1 (16:9) and 1.33:1 (4:3) video. V Stretch: This is the most suitable mode for using a 2.35:1 screen to view 2.35:1 video with a commercially available anamorphic lens. When you select “V Stretch” from “Trigger Select 1/2” on the Installation menu, a 12 V signal is output from the TRIGGER 1 or TRIGGER 2 connector (page 29). Squeeze: With this setting, 1.78:1 (16:9) and 1.33:1 (4:3) video will be displayed in their correct aspect ratios when you use a commercially available anamorphic lens. Stretch: Displays video that has been squeezed to 1.33:1 (4:3) as 1.78:1 (16:9) aspect ratio. Tips • When you select “V Stretch” or “Squeeze,” select the anamorphic lens type from “Anamorphic Lens” in the Installation menu. • Selectable aspect modes vary depending on the input signal (page 43). • Aspect setting is stored for each of the five Picture Positions. Adjust the aspect after selecting the Picture Position. Final adjusted values are stored automatically. 23 Setting items Description Blanking This feature allows you to adjust the displayable region within the four directions of the screen. On: Select the edge to adjust by highlighting Left, Right, Top, or Bottom using the M/m button. Adjust the amount of blanking using the , button. Off: Turns off the Blanking function. Tips • Depending on the aspect ratio setting, right/left blanking may not be available. • Blanking setting is stored for each of the five Picture Positions. Adjust the blanking after selecting the Picture Position. Final adjusted values are stored automatically. 24 Setup Menu The Setup menu is used to change the factory preset settings, etc. Setting items Description Status Sets whether or not the on-screen display is displayed. On: Displays on-screen messages and menus. Off: Turns off the on-screen displays, other than certain menus, a message when turning off the power, and warning messages. Language Selects the language used in the menu and on-screen displays. Menu Position You can change the position to display the menu on the projection surface. Bottom Left: Displays the menu on the bottom left area of the projection surface. Center: Displays the menu on the center of the projection surface. High Altitude Mode Sets the unit to operate at the prevailing atmospheric pressure. On: Use this setting when using the unit at an altitude of 1,500 m (approx. 4,900 ft) or higher. Off: Use this setting when using the unit at normal altitudes. Tip When this item is set to “On,” the fan noise becomes slightly louder since the fan speed increases. Remote Start Sets the Remote Start settings. On: You can turn on the power from a PC or a terminal which is connected to a network. Off: Turns off the Remote Start function. Tips • To use the function, the unit should be connected to the network in advance (page 30). • To turn on the power with the Remote Start function, a special command should be sent from a PC or a terminal. For details, consult with qualified Sony personnel. Note When the Remote Start is set to “On,” the standby power requirement will increase. When Network Management is set to “On,” Remote Start is automatically fixed at “Off” and is not displayed in the menu. Network Management On: Set when connected to the network and continuously communicating with the projector control equipment. Off: Turns off the Network Management function. Note When Network Management is set to “On,” the network function is continuously enabled. Set Network Management to “Off” for normal use. If you set to “On,” the power consumption increases. Power Saving Sets the Power Saving mode. Standby: If no signal is input for 10 minutes, power is turned off automatically and the projector goes into standby mode. Off: Disables the Power Saving function. All Reset All settings are initialized to their factory preset values. 25 Function Menu The Function menu is used for changing the settings of the various functions of the unit. Setting items Description 3D Settings You can change the settings of the 3D function. 2D-3D Display Sel. For Switching the video images to “2D” or “3D.” Auto: Displays 3D video images when HDMI signals with 3D information* are input. Displays 2D video images when other signals are input. 3D: Displays 3D video images according to the 3D system selected in “3D Format.” However, when HDMI signals with 3D information are input to the unit, displays 3D video images according to the 3D system of those HDMI signals. * The 3D information is additional information to discriminate 3D. Some HDMI signals have additional information to discriminate 3D and some HDMI signals have none. 3D Format: Set the 3D system when the input HDMI signals do not include 3D information. Simulated 3D: Converts 2D video images to 3D video images. The setting can be made only for input the HD signals. The simulated 3D feature may have limited effect, depending on the video source. There are differences in perception of 3D video images among individuals. Side-by-Side: Select this to display 3D images as two similar images, side-by-side. Over-Under: Select this to display 3D images as two similar images, one above the other. Tips • “2D-3D Display Sel.” cannot be set to “3D” for some video sources. For available 3D signals, see “Compatible 3D Signals” (page 42). • The simulated 3D feature may have limited effect, depending on the screen size (100 to 120 inches recommended) and the video source. • The menu display has a ghost while a 3D video image is displayed and is best viewed with the 3D glasses. 3D Depth Adjust For adjusting the depth of the 3D video images on the projection surface. The setting can be made only when a 3D Format other than “Simulated 3D” is selected. Depth Front Normal Depth We recommend that “3D Depth Adjust” be set to “0.” The 3D video images may be difficult to perceive, depending on the setting of “3D Depth Adjust.” Simulated 3D Effect For adjusting the 3D effect when 2D content is converted to 3D video images. You can select the effect from among “High,” “Middle,” and “Low.” Tip There are differences in perception of 3D video images converted by the simulated 3D function among individuals. Dynamic Range Sets the video input level for HDMI 1 and HDMI 2 connectors. Auto: Sets the video input level automatically. Limited: The video input level is set for signals that are equivalent to 16-235. Full: The video input level is set for signals that are equivalent to 0-255. Note If the video output setting of the connected HDMI device is not set correctly, light and dark parts of the video may appear too light or too dark. HDMI Signal Format Switches the video signal formats for 4K. Standard Format: Displays a picture in the standard HDMI format. Normally use this setting. Enhanced Format: Displays a picture in a more detailed HDMI format. Use this setting only when the corresponding devices are used. Tips • A picture or sound may not be output normally when “Enhanced Format” is selected. In this case, set to “Standard Format.” • Set “Enhanced Format” only when the corresponding devices are used. • It may take time to display a picture after switching the video signal formats. 26 Setting items Description Test Pattern Displays a test pattern according to the setting. On: A test pattern appears on the screen to be used when adjusting the lens with “Lens Focus,” “Lens Zoom,” and “Lens Shift.” Off: A test pattern does not appear. Tip While the test pattern is displayed, it is only displayed in green to allow you to adjust the focus easily. Settings Lock Locks menu item settings to prevent operational error (page 28). Off: Cancels the Settings Lock. Level A: Group 1 items (below) are not displayed on the menu, and are not available. Level B: Group 1 and Group 2 items (below) are not displayed on the menus, and are not available. 27 Items Locked by Settings Lock Group 1 Group 2 Picture menu Setup menu Reset Reality Creation Laser Light Setting Contrast Enhancer Motionflow Contrast Brightness Color Hue Color Temp. Sharpness NR MPEG NR Smooth Gradation Film Mode Gamma Correction Color Correction Clear White x.v.Color HDR Color Space Input Lag Reduction Status Language Menu Position High Altitude Mode Remote Start Network Management Power Saving Function menu Dynamic Range Test Pattern Installation menu Image Flip Lens Control Anamorphic Lens Trigger Select IR Receiver Panel Alignment Network Setting Advanced Picture menu Auto Calibration 28 Installation Menu The Installation menu is used for changing the installation settings. Setting items Description Image Flip Flips the picture on the screen horizontally and/or vertically. HV: Flips the picture horizontally and vertically. H: Flips the picture horizontally. V: Flips the picture vertically. Off: The picture does not flip. Use this item for installation for the rear projection or ceiling installation. Lens Control Avoids any operation of the lens such as “Lens Focus,” “Lens Zoom,” and “Lens Shift,” by mistake. On: Enables adjustment of the lens. Off: Prevents any adjustment of the lens. Anamorphic Lens Select a setting to match the anamorphic lens conversion ratio. 1.24x: Select this when you use an anamorphic lens with a horizontal rate of 1.24×. 1.32x: Select this when you use an anamorphic lens with a horizontal rate of 1.32×. Trigger Select Switches the output function of the TRIGGER 1/TRIGGER 2 connector. Off: Turns off the TRIGGER connector function. Power: Outputs 12 V signals from the TRIGGER 1/TRIGGER 2 connectors when the unit is on. The TRIGGER 1/TRIGGER 2 connectors do not output any signals when the unit is in standby. V Stretch: Works with the “Aspect” setting’s “V Stretch” (page 23) and outputs a 12 V signal from the TRIGGER 1 or TRIGGER 2 connector. 2.35:1 Zoom: Works with the “Aspect” setting’s “2.35:1 Zoom” (page 23) and outputs a 12 V signal from the TRIGGER 1 or TRIGGER 2 connector. IR Receiver Selects the remote control detectors (IR Receiver) on the front and rear of the unit. Front & Rear: Activates both the front and rear detectors. Front: Activates the front detector only. Rear: Activates the rear detector only. Panel Alignment This feature allows you to adjust the gaps in the color of characters or the picture on the screen. Adjust: Adjusts the gaps in the colors selecting “Adjust Item” or “Adjust Color.” Adjust Item: Selects how to make adjustments from below. Shift: Shifts the whole picture and makes adjustments. Zone: Selects the desired range and makes adjustments. Adjust Color: Assigns the desired color to adjust the gaps in color. Select “R” (Red) or “B” (Blue) to make adjustments based on “G” (Green). Pattern Color: Select “R/G” (Red and Green) or “R/G/B” (White, all colors) when “Adjust Color” is “R” (Red). Select “B/G” (Blue and Green) or “R/G/B” (White, all colors) when the “Adjust Color” is “B” (Blue). Adjust: The shift adjustment and zone adjustment of the color selected in “Adjust Color” can be made with the ,/M/m button. When “Shift” is selected: Assign the settings of the horizontal direction (H) with the , button and the vertical direction (V) with the M/m button on the shift adjustment screen. 29 Setting items Description When “Zone” is selected: Select the position to adjust with the , button for the horizontal position (H Position) and the M/m button for the vertical position (V Position), then press . Set the amount to adjust with the , button for the horizontal direction (H) and with the M/m button for the vertical direction (V). You can select the position to adjust again by pressing . Reset: Returns to the factory settings. Preset: The optimized data has been preset. Note Depending on the adjustments made above, colors may become uneven or the resolution may change. Network Setting IPv4 Setting Perform internet protocol settings. IP Address Setup: Selects the IP address setting method. Auto(DHCP): The IP address is assigned automatically from the DHCP server such as a router. Manual: Specifies the IP address manually. When “Manual” is selected for “IP Address Setup,” input “IP Address,” “Subnet Mask,” and “Default Gateway.” Select each item with the M/m button, then press button. Select the frame to input with the , button and input the value with the M/m button. When all items are entered, select “Apply,” and then press the button. The entered settings will be registered. IP Address: Sets the unit’s IP address. Subnet Mask: Sets the unit’s subnet mask. Default Gateway: Sets the unit’s default gateway. MAC Address: Displays the unit’s MAC address. This cannot be changed. Apply: Enables the IP address that is set manually. IPv6 Information Displays the IPv6 information. When you set the IPv6 IP address, set it on a Web browser (page 32). 30 Information Menu The Information menu displays the model name, serial number, input signal type/format, software version and the cumulated hours of usage of the light. Items Description Model Name Displays the model name Serial No. Displays the serial number. Signal type Displays the resolution of the input signal which you are selecting. When input signals with 3D information are input, the type of input signals and the 3D format are displayed. Color Format Displays the color format of the input signal which you are selecting. Color Space Displays the color space of the input signal which you are selecting (“BT.601,” “BT.709,” or “BT.2020”). HDR Format When the input signal is compatible with HDR, “HDR10” or “HLG” is displayed according to the input signal. Software Version Displays the software version. Light Timer Displays how long the light has been turned on (total usage). Note You cannot adjust or change the displays listed above. About the Preset Memory This unit has default image data to adjust preset data for input signals appropriately according to the signals shown in “Preset Signals” (page 40) (the preset memory). When the preset signal is input, the unit automatically detects the signal type and recalls the data for the signal from the preset memory to adjust it to an optimum picture. The signal type is displayed in the Information menu. Note Depending on the computer input signal, parts of projection image may be hidden or displayed incorrectly. 31 Using Network Features 3 Connection to the network allows you to operate the following features: • Checking the current status of the unit via a Web browser. • Making the network settings for the unit. • Network monitoring and controlling with control protocol (SDAP [Advertisement], SDCP [PJ Talk], DDDP [AMX], Crestron RoomView, Control4). When connecting by the IPv6 address http://[xxxx:xxxx:- xxxx] Notes You can confirm the IP address of the unit under “Network Setting” on the Installation menu. • When connecting this projector with the network, consult with the person who sets up the network. The network must be secured. • When using this projector connected with the network, access the Control window via a Web browser and change the access limitation of the factory preset values (page 33). It is recommended to change the password regularly. • When the setting on the Web browser is completed, close the Web browser to log out. • The menu displays used for the explanation below may be different depending on the model you are using. • Supported Web browsers are Internet Explorer 8/9/10/11. • The menu displays only English. • If the browser of your computer is set to [Use a proxy server] when you have access to the unit from your computer, click the check mark to set accessing without using a proxy server. • AMX DDDP is not compatible with IPv6. • These network functions are available when the unit is turned on. The following window appears in the Web browser: Once you make the network settings, you can open the Control window only by performing step 3 of this procedure. Displaying the Control Window of the Unit with a Web Browser 1 Connect the LAN cable. LAN cable (straight type) (not supplied) LAN Connector Hub, router, etc. 2 Start a Web browser on the computer, enter the following in the address field, then press the Enter key on your computer. http://xxx.xxx.xxx.xxx (xxx.xxx.xxx.xxx: IP address for the unit) Set the network settings for the unit using “Network Setting” on the Installation menu (page 30). 32 The default password “Projector” cannot be set as a new password. Operating the Control Window Note If you forget your password, consult with qualified Sony personnel. Switching the Page Confirming the Information Regarding the Unit Click one of the Page Switching buttons to display the desired setting page. You can confirm the current settings for the unit on the Information page. Page Switching buttons Setting the Access Limitation You can limit a user for accessing any particular page. Administrator: Allowed access to all pages User: Allowed access to all pages except the Setup page When you access the Setup page for the first time, input “root” as the user name and “Projector” as the password in the authentication dialog. When you log in for the first time, the window that prompts you to change the password is displayed. Follow the instructions on the screen to change the password. The name of the administrator is preset to “root.” Information area Entry area for [Administrator] Entry area for [User] The password can be changed in the Password page in the Setup page. When you change the password, input a new password after deleting the password (*****) that was set. The password of the administrator and user should be 8 to 16 characters that includes both alphabet and numeric characters. Alphabet is case-sensitive. 33 Error Handling Troubleshooting If the unit appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel. Power Symptom Cause and Remedy Page The power is not turned on. The power may not turn on if you turn the power off with ?/1 (On/Standby) button and turn it on again in a short time. After about 1 minute, turn the power on. Check the indicators. 36 The power is suddenly turned off. Check that “Power Saving” in the Setup Set “Power Saving” to “Off.” 25 25 menu is set to “Standby.” – Picture Symptom No picture. Cause and Remedy Check that the connecting cable is connected to the external equipment properly. Page 10 Select the input source correctly using the INPUT button. Check that the computer signal is set for output to an external monitor. If a notebook computer and the signal is output to its display and an external monitor, the external monitor’s image may not be displayed correctly. Set your computer to output the signal to only an external monitor. 11 – The picture has ghosts. Video images are displayed in 3D. Watch the 3D video images using the 3D glasses, and set “2D-3D Display Sel.” to “3D.” 12, 26 Bright or dark area of the video appears too bright or too dark. This symptom may occur when a signal level other than those of HDMI standard is input. Switch the output level of the connected equipment, or switch the Dynamic Range on the Function menu of the unit. 26 The picture is too dark. The picture is not clear. Adjust “Contrast” or “Brightness” on the Picture Adjust the focus. 19 7 menu properly. If the lens is clouded with dew condensation, leave the unit for about 2 hours with the power on. The color of characters or the picture Select the desired color registration in “Panel Alignment” on the Installation is not appropriate. menu. – 29 Image is left on the projection image. When high contrast non-moving images are displayed for a long period of time, there may (Image retention) be some image retention on the projection image. This is only a temporary condition. Turning off the power for a while will eliminate the retained image. – Some color appears around the picture. – It may appear due to condensation. Wait for about 5 minutes with the power on. On-screen display Symptom Cause and Remedy On-screen display does not appear. Set “Status” on the Setup menu to “On.” Check if the ON/STANDBY indicator should light in green. When the ON/STANDBY indicator blinks in green, the unit is starting up. Wait until it stops blinking and remains lit in green. Page 25 7 The model name does not disappear from the screen. The display mode of the unit may be set at the time of purchase. Consult with your local dealer or qualified Sony personnel. – 34 Remote control Symptom The remote control does not work. Cause and Remedy Batteries could be weak. Replace them with new batteries. Page – Insert the batteries with the correct polarities. If there is a fluorescent lamp near the remote control detector, the unit may work improperly or inadvertently. Confirm the position of the remote control detector on the unit. Set “IR Receiver” to “Front & Rear” on the Installation menu. Make sure that the cable is not connected to the IR IN connector. – – 3, 4 29 3 3D video images Symptom The video image does not seem like 3D video images. Cause and Remedy Check if the 3D glasses are turned on. Page 12 Make sure that the battery in the 3D glasses is sufficiently charged. Set “2D-3D Display Sel.” to “Auto” or “3D.” – 26 Check if the input signals are compatible 3D signals. The 3D signals may not be input depending on the specifications of the connected AV selector/AV amplifier/external equipment. If the 3D signal is not input, confirm the specifications and/or settings of the AV selector/AV amplifier/external equipment. When the viewing position is too far from the unit, the 3D glasses may not be able to display the images properly. The screen size is not appropriate. Set the zooming magnification to low or watch the image from farther away from the screen. 42 – For details, see “Precautions for use” of “Using the 3D Glasses.” 12 47 12 Others Symptom Cause and Remedy The fan is noisy. Check the setting of “High Altitude Mode” on the Setup Make sure that the room temperature is not too high. The lens shift cannot be adjusted. Page menu. Check the installation requirements of the unit. Fan speed increases to maintain the product reliability of the projector’s components in a room where the temperature is higher than normal. The fan noise becomes slightly louder in these rooms. The approximate normal temperature for the unit is 25°C (77°F). The lens shift cannot be adjusted over the range of movement. Adjust the lens shift within the range of movement. 35 25 – – 8, 47 About Indicators The ON/STANDBY or WARNING indicator lights up or flashes if there is any trouble with your projector. ON/STANDBY indicator Flashing/Lighting indicators WARNING indicator The number of flashes Cause and Remedy Three times The unit does not light properly due to an abnormality of the light source and light source power. Turn off, then turn on the power after a while. If the symptom persists, consult qualified Sony personnel. Six times The unit detects a drop impact. If there is abnormality on the unit, consult with qualified Sony personnel. If there are no abnormalities on the unit, disconnect the AC power cord and check that the ON/STANDBY indicator turns off, then connect the AC power cord and turn the unit on. Twice The internal temperature is unusually high. Check to ensure that nothing is blocking the ventilation holes and the unit is not being used at high altitudes. The fan is broken. Consult with qualified Sony personnel. (Lights in red) (Flashes in red) Three times (Flashes in red) (Flashes in red) Both indicators flash Note If the symptom persists even after carrying out the above methods, consult with qualified Sony personnel. If the indicator starts flashing in a way of other than the above, turn off, and then turn on the power with the [/1 (On/Standby) button on the remote control or control panel of the unit. If the symptom is shown again, consult with qualified Sony personnel. 36 Message Lists Warning messages Symptom High temp.! Light off in 1 min. Cause and Remedy Turn off the power. Frequency is out of range! Check to ensure that nothing is blocking the ventilation holes. Frequency is out of range. Input a signal that is within the acceptable frequency range of the unit. 3, 4 40 Check to ensure that nothing is blocking the ventilation holes. 3, 4 When using the unit at high altitude, set “High Altitude Mode” to “On.” 25 Projector temperature is high. High Altitude Mode should be “On” if Projector is being used at high altitude. Page – Note When temperature inside the unit remains high, “High Altitude Mode” is switched to “On” in 1 minute, then the fan speed increases. Power Saving Mode is set. Projector will automatically enter Standby Mode in 1 minute. “Power Saving” is set to “Standby.” 25 Note If no signal is input, the power turns off after 1 minute, and the projector goes into standby mode. Caution messages Symptom x Not applicable! Settings Lock enabled. Cause and Remedy No signal is input in the selected input. Check connections. Press the appropriate button. The operation to be activated by the button is currently prohibited. “Settings Lock” is set to “Level A” or “Level B.” 37 Page 10 – 27 Others Updating the Software You can download files to update the software of the unit. Copy the downloaded files to your USB memory, insert the USB memory to the USB terminal of the unit, then perform the update. To use the features updated, insert a USB memory device into a PC connected to the internet. Download the update files from the following Sony website: http://www.pro.sony.eu/ The website also explains how to install the update. Note Some USB memories may not be supported for use. For details, refer to the website above. About HDR (high dynamic range) HDR is a video expression which improves the ability to express dark places and bright places compared to previous video expressions. About the Simulated 3D Feature • Use the simulated 3D function taking into account that the picture will provide a different look from the original images, because this function converts the video images. • Note that if the unit is used for profit or for public viewing, displaying 2D video images as 3D video images by converting to the simulated 3D may constitute an infringement of the rights of authors or producers, which are legally protected. Trademark Information • “PlayStation” is a registered trademark of Sony Computer Entertainment Inc. • The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. • “Blu-ray” and “Blu-ray Disc” are trademarks of Blu-ray Disc Association. • “x.v.Color (x.v.Colour)” and “x.v.Color (x.v.Colour)” logo are trademarks of Sony Corporation. ..................................................................................... This projector supports DeepColor, x.v.Color, LipSync, computer input signal, 3D signal, 4K signal of HDMI standards. It also supports HDCP. NOTICES AND LICENSES FOR SOFTWARE USED IN THIS PRODUCT Refer to “Software License Information” supplied separately. 38 Specifications Item Display System Display device Description SXRD panel, projection system Size of effective display area 0.74-inch (18.8 mm) SXRD Number of pixels Light source 26,542,080 pixels (8,847,360 pixels × 3) 2.06 times zoom lens (motorized) f = 21.7 mm to 44.7 mm F3.0 to F4.0 Laser diode Projection image size Accepted digital signals 60-inch to 300-inch (1,524 mm to 7,620 mm) (measured diagonally) See “Preset Signals” (page 40). Inputs/Outputs HDMI connectors (HDCP 2.2) ×2 TRIGGER connectors × 2, mini jack, DC 12 V, Max. 100 mA REMOTE connector LAN connector RS-232C: D-sub 9-pin (male) RJ45, 10BASE-T/100BASE-TX IR IN connectors USB connector Minijack Type A, DC 5 V, Max. 500 mA Projection lens Mass 560 mm × 223 mm × 496 mm (22 1/16 inches × 8 25/32 inches × 19 17/32 inches) (without protrusions) Approx. 20 kg (44 lb) Power requirements Power consumption AC 100 V to 240 V, 4.3 A to 1.8 A, 50/60 Hz 430 W Standby mode power Standby consumption Networked Standby Operating temperature 0.4 W (when “Remote Start” is set to “Off”) 1.0 W (LAN) (when “Remote Start” is set to “On”)When a LAN terminal is not connected, it becomes a low power consumption mode (0.5 W). 5°C to 35°C (41°F to 95°F) Operating humidity Storage temperature 20% to 80% (no condensation) –10°C to +60°C (14°F to 140°F) Storage humidity Supplied accessories 20% to 80% (no condensation) See “Checking the Supplied Accessories” on the Quick Reference Manual. Optional accessories Projector Suspension Support: PSS-H10 Active 3D Glasses: TDG-BT500A Outside dimensions (w/h/d) Notes • The values for mass and dimensions are approximate. • Not all optional accessories are available in all countries and area. Please check with your local Sony Authorized Dealer. • Information on optional accessories in this manual is current as of November 2017. Design and specifications of this unit and its optional accessories are subject to change without notice. 39 Preset Signals The following table shows the signals and video formats which you can project using this unit. When a signal other than the preset signals shown below is input, the picture may not be displayed properly. Preset memory no. Preset signal (resolution) fH (kHz) fV (Hz) Sync 5 480/60p 480/60p (Progressive NTSC) (720 × 480p) 31.470 60.000 – 6 576/50p 576/50p (Progressive PAL) (720 × 576p) 31.250 50.000 – 7 1080/60i 1080/60i (1920 × 1080i) 33.750 60.000 – 8 1080/50i 1080/50i (1920 × 1080i) 28.130 50.000 – 10 720/60p 720/60p (1280 × 720p) 45.000 60.000 – 11 720/50p 720/50p (1280 × 720p) 37.500 50.000 – 12 1080/60p 1080/60p (1920 × 1080p) 67.500 60.000 – 13 1080/50p 1080/50p (1920 × 1080p) 56.260 50.000 – 14 1080/24p 1080/24p (1920 × 1080p) 26.973 23.976 – 18 720/60p (Frame packing) 720/60p (1280 × 720p) 90.000 60.000 – 19 720/50p (Frame packing) 720/50p (1280 × 720p) 75.000 50.000 – 20 1080/24p (Frame packing) 1080/24p (1920 × 1080p) 53.946 23.976 – 26 640 × 480 VESA 60 31.469 59.940 H-Neg, V-Neg 32 800 × 600 VESA 60 37.879 60.317 H-Pos, V-Pos 37 1024 × 768 VESA 60 48.363 60.004 H-Neg, V-Neg 45 1280 × 960 VESA 60 60.000 60.000 H-Pos, V-Pos 47 1280 × 1024 VESA 60 63.974 60.013 H-Pos, V-Pos 50 1400 × 1050 SXGA+ 65.317 59.978 H-Neg, V-Pos 55 1280 × 768 1280 × 768/60 47.776 59.870 H-Neg, V-Pos 71 1920 × 1080/60i (Frame packing) 1080/60i (1920 × 1080i) 67.500 60.000 – 72 1920 × 1080/50i (Frame packing) 1080/50i (1920 × 1080i) 56.250 50.000 – 74 3840 × 2160/60p 3840 × 2160/60p (3840 × 2160) 135.000 60.000 – 75 3840 × 2160/50p 3840 × 2160/50p (3840 × 2160) 112.500 50.000 – 76 4096 × 2160/60p 4096 × 2160/60p (4096 × 2160) 135.000 60.000 – 77 4096 × 2160/50p 4096 × 2160/50p (4096 × 2160) 112.500 50.000 – 78 4096 × 2160/30p 4096 × 2160/30p (4096 × 2160) 67.500 30.000 – 79 4096 × 2160/25p 4096 × 2160/25p (4096 × 2160) 56.250 25.000 – 93 3840 × 2160/24p 3840 × 2160/24p (3840 × 2160) 53.946 23.976 – 94 3840 × 2160/25p 3840 × 2160/25p (3840 × 2160) 56.250 25.000 – 40 Preset memory no. Preset signal (resolution) fH (kHz) fV (Hz) Sync 95 3840 × 2160/30p 3840 × 2160/30p (3840 × 2160) 67.433 29.970 – 96 4096 × 2160/24p 4096 × 2160/24p (4096 × 2160) 54.000 24.000 – Preset memory numbers for each input signal Digital signal Signal Preset memory number Component signal (HDMI 1, 2 connectors) Video GBR signal (HDMI 1, 2 connectors) 5 to 8, 10 to 14, 18 to 20, 71, 72, 74 to 79, 93 to 96 5 to 8, 10 to 14, 18 to 20, 71, 72, 74 to 79, 93 to 96 Computer signal (HDMI 1, 2 connectors) 10*, 12*, 26, 32, 37, 45, 47, 50, 55 * Some digital signals input from computers may be displayed as preset memory number of Component or Video GBR signal. Input Signals and Adjustment/Setting Items The items in the menus available to adjust differ depending on the input signal. The following tables indicate them. The items that cannot be adjusted/set are not displayed in the menu. Picture menu Component signal Input signal Video GBR signal Computer signal Reality Creation Laser Light Setting z z – z z z Contrast Enhancer Motionflow*1 z z z z – – Contrast Brightness z z z z z z Color Hue z z z z – – Color Temp. Sharpness z z z Item z z – (excluding preset memory numbers 18 to 20, 71, and 72) z (excluding preset memory numbers 18 to 20, 71, and 72) (excluding preset memory numbers 18 to 20, 71, and 72) z (excluding preset memory numbers 18 to 20, 71, and 72) – z (excluding preset memory numbers 18 to 20, 71 and 72) z (excluding preset memory numbers 5, 6, 10 to 14, 18 to 20, 74 to 79, and 93 to 96) z (excluding preset memory numbers 18 to 20, 71 and 72) z (excluding preset memory numbers 5, 6, 10 to 14, 18 to 20, 74 to 79, and 93 to 96) – Gamma Correction Color Correction z z z z z z Clear White x.v.Color z z z z – NR MPEG NR Smooth Gradation Film Mode HDR Color Space z z (preset memory numbers 74 to 79 and 93 to 96 only) z z z (preset memory numbers 74 to 79 and 93 to 96 only) z z: Adjustable/can be set –: Not adjustable/cannot be set *1: For further details, refer to the tables in “Motionflow” (page 44). 41 – – – – z Screen menu Input signal Item Component signal Video GBR signal z z Aspect*1 Computer signal – z: Adjustable/can be set –: Not adjustable/cannot be set *1: For further details, refer to the tables in “Aspect Mode” (page 43). Note When connecting a cable such as an HDMI cable, etc., check the type of the signal in the Information (page 41), and check items that are adjustable/can be set. menu (page 31) and “Digital signal” Compatible 3D Signals This unit accepts the following types of 3D signals. Resolution 3D signal format 720/60p, 720/50p Side-by-Side format Over-Under format* Frame packing* 1080/60i, 1080/50i Side-by-Side format* Frame packing 1080/24P Side-by-Side format Over-Under format* Frame packing* 1080/60p, 1080/50p Side-by-Side format Over-Under format *: Mandatory 3D format of the HDMI standards. 3D Signals and Adjustable/Setting Items Some items on the menus may not be available to adjust/set, depending on the 3D signals. The items that cannot be adjusted are not displayed on the menu. The following tables indicate those items. Item 720/60p, 720/50p 3D signals 1080/60i, 1080/50i 1080/24p 1080/60p, 1080/50p Reality Creation Laser Light Setting*1 z z z z z z z z Motionflow NR z z z z – – – – MPEG NR Smooth Gradation – – – – – – – – Film Mode x.v.Color – z – – z z z z HDR Aspect*2 – – – – z z z z z: Adjustable/can be set –: Not adjustable/cannot be set *1: “Dynamic Control” cannot be selected. *2: For further details, refer to the tables in “Aspect Mode” (page 43). 42 When the unit is set to convert 2D video images to 3D video images, some items on the menus may be not available to adjust/set, depending on the “3D Format” settings on the Function menu. The items that cannot be adjusted are not displayed on the menu. The following tables indicate these items. 3D signals Item Reality Creation Laser Light Motionflow Setting*1 Over-Under Side-by-Side Simulated 3D z z z z z z z z z NR – – z MPEG NR Smooth Gradation – – – – z Film Mode* x.v.Color 2 HDR Aspect*3 z – z z z z z – – – z z z z: Adjustable/can be set –: Not adjustable/cannot be set *1: “Dynamic Control” cannot be selected. *2: This item is available only when the 1080/60i or 1080/50i signal is input. *3: For further details, refer to the tables in “Aspect Mode” (page 43). Aspect Mode Selectable items vary depending on the type of input signal or 3D format. For details, see the tables below. Items that cannot be selected are not displayed in the menu. 2D Acceptable signals 4096 × 2160 3840 × 2160 1920 × 1080 1280 × 720 720 × 480 720 × 576 Others Preset memory number (page 40) 76 to 79, 96 74, 75, 93 to 95 7, 8, 10 to 14 5, 6 26, 32, 37, 45, 47, 50,55 1.85:1 Zoom – z z z – 2.35:1 Zoom – z z z – Normal z z z z z* V Stretch z z z z – Squeeze z z z z – Stretch – – – z – *1: Not displayed in the menu as fixed at Normal. 43 1 3D Acceptable signals 1920 × 1080, 1280 × 720 3D format Side-by-Side Over-Under Frame packing Simulated 3D Preset memory number (page 40) 7, 8, 10 to 14 10 to 14 18 to 20, 71, 72 7, 8, 10 to 14 1.85:1 Zoom z z z z 2.35:1 Zoom z z z z Normal z z z z V Stretch z z z z Squeeze z z z z Stretch – – – – Motionflow Selectable items vary depending on the type of input signal or 3D format. For details, see the tables below. Items that cannot be selected are not displayed in the menu. 2D Acceptable signals 1920 × 1080 1280 × 720 720 × 480 720 × 576 3840 × 2160 4096 × 2160 Preset memory number (page 40) 5 to 8, 10 to 14 74, 75, 93 to 95 76 to 79, 96 Impulse z z z Combination Smooth High z z z z – – – – Smooth Low True Cinema z z z z – – – – Others 26, 32, 37, 45, 47, 50, 55 – 3D Acceptable signals 3D format Preset memory number (page 40) Impulse Combination Smooth High Smooth Low True Cinema 1920 × 1080, 1280 × 720 Over-Under Frame packing 18 19 – – – – 20, 71, 72 – – z z z z – – Side-by-Side Simulated 3D 10,12 11,13 14 7, 8, 10 to 14 7, 8, 10 to 14 – – – – – – – – – – z z z z z z z z z z z z – – – – – – 44 Storage Conditions of Adjustment/Setting Items Each adjustable/setting item is individually stored for each input connector. For further details, see the tables below. Preset memory numbers for each input signal Input HDMI 1 (2D) Preset memory numbers 5 to 8, 10 to 14, 26, 32, 37, 45, 47, 50, 55, 74 to 79, 93 to 96 HDMI 2 (2D) HDMI 1 (3D) 7, 8, 10 to 14, 18 to 20, 71, 72 HDMI 2 (3D) Picture menu Item Storage conditions Calib. Preset For each input connector Reset For each input connector and Calib. Preset Reality Creation Laser Light Setting Contrast Enhancer Motionflow Contrast Brightness Color Hue Color Temp. D93 - D55 Custom 1-5 Gain R For each Color Temp., D93-D55 and Custom 1-5 Gain G Gain B Bias R Bias G Bias B Sharpness For each input connector and Calib. Preset NR MPEG NR Smooth Gradation Film Mode Gamma Correction Color Correction Clear White x.v.Color HDR Color Space 45 Item Red Storage conditions For each Color Space Green Blue Cyan - Red Magenta - Green Input Lag Reduction For each input connector and Calib. Preset Screen menu Item Storage conditions Aspect For Picture Position 1.85:1, 2.35:1, or Custom 1-3 Blanking 46 Projection Distance and Lens Shift Range The projection distance refers to the distance between the front of the lens and the projected surface. Projection distance L Front of the lens Projected image The lens shift range represents the distance in percent (%) by which the lens can be shifted from the center of the projected image. The lens shift range is regarded as 0% when the point A in the illustration (point where a line drawn from the center of the lens and the projected image cross at right angles) is aligned with the center of the projected image and full width or full height of the projected image is regarded as 100%. Projected image 50% Lens shift range Center of the projected image Center of the lens 50% A Side of the unit Projected image 50% Lens shift range Center of the projected image Center of the lens 50% A Top of the unit VS + HS – Center of the lens HS + VS – Projected image Shaded region: Lens shift range VS +:Vertical lens shift range (up) [%] VS –:Vertical lens shift range (down) [%] HS +:Horizontal lens shift range (right) [%] HS –:Horizontal lens shift range (left) [%] 47 When projecting in 1.90:1 (Native Full Display 17:9) format 1.90 1 Projection distance Unit: m (inches) Projection image size Projection distance L Diagonal Width × Height 80" (2.03 m) 100" (2.54 m) 1.80 × 0.95 (71 × 37) 2.25 × 1.18 (88 × 47) 2.32 – 4.77 (91 – 187) 2.90 – 5.97 (115 – 235) 120" (3.05 m) 150" (3.81 m) 2.70 × 1.42 (106 × 56) 3.37 × 1.78 (133 × 70) 3.49 – 7.18 (138 – 282) 4.38 – 8.98 (173 – 353) 200" (5.08 m) 4.49 × 2.37 (177 × 93) 5.85 – 11.99 (231 – 472) Projection distance formula D: Projected image size (Diagonal) Unit: m (inches) Projection distance L (minimal length) L = 0.029432 × D – 0.0434 (L = 1.158727 × D – 1.7084) Projection distance L (maximal length) L = 0.060197 × D – 0.0420 (L = 2.369978 × D – 1.6545) Lens shift range 85% 31% 31% VS + = 85 – 2.742 × (HS + or HS –) [%] VS – = 80 – 2.742 × (HS + or HS –) [%] HS + = HS – = 31 – 0.365 × (VS + or VS –) [%] 80% 48 When projecting in 1.78:1 (16:9) format 1.78 Video display area Projection area 1 Projection distance Unit: m (inches) Projection image size Projection distance L Diagonal Width × Height 80" (2.03 m) 100" (2.54 m) 1.77 × 1.00 (70 × 39) 2.21 × 1.25 (87 × 49) 2.44 – 5.01 (96 – 197) 3.05 – 6.28 (121 – 247) 120" (3.05 m) 150" (3.81 m) 2.66 × 1.49 (105 × 59) 3.32 × 1.87 (131 × 74) 3.67 – 7.55 (145 – 297) 4.60 – 9.44 (181 – 371) 200" (5.08 m) 4.43 × 2.49 (174 × 98) 6.15 – 12.61 (242 – 496) Projection distance formula D: Projected image size (Diagonal) Unit: m (inches) Projection distance L (minimal length) L = 0.030934 × D – 0.0434 (L = 1.217856 × D – 1.7084) Projection distance L (maximal length) L = 0.063269 × D – 0.0420 (L = 2.490916 × D – 1.6545) Lens shift range 85% 33% 33% VS + = 85 – 2.576 × (HS + or HS –) [%] VS – = 80 – 2.576 × (HS + or HS –) [%] HS + = HS – = 33 – 0.388 × (VS + or VS –) [%] 80% 49 When projecting in 2.35:1 format 2.35 Video display area Projection area 1 Projection distance Unit: m (inches) Projection image size Projection distance L Diagonal 80" (2.03 m) Width × Height 1.87 × 0.80 (74 × 31) 2.41 – 4.96 (95 – 195) 100" (2.54 m) 120" (3.05 m) 2.34 × 0.99 (92 × 39) 2.80 × 1.19 (110 × 47) 3.02 – 6.22 (119 – 244) 3.64 – 7.47 (143 – 294) 150" (3.81 m) 200" (5.08 m) 3.51 × 1.49 (138 × 59) 4.67 × 1.99 (184 × 78) 4.55 – 9.35 (180 – 368) 6.08 – 12.48 (240 – 491) Projection distance formula D: Projected image size (Diagonal) Unit: m (inches) Projection distance L (minimal length) Projection distance L (maximal length) L = 0.030617 × D – 0.0434 (L = 1.205377 × D – 1.7084) L = 0.062621 × D – 0.0420 (L = 2.465393 × D – 1.6545) Lens shift range 105% 31% 31% VS + = 105 – 3.387 × (HS + or HS –) [%] VS – = 99 – 3.387 × (HS + or HS –) [%] HS + = HS – = 31 – 0.295 × (VS + or VS –) [%] 99% 50 Dimensions Front Unit: mm (inches) 560 (22 1/16) 280 (11 1/32) 280 (11 1/32) 128 (5 1/32) 223 (8 25/32) 230 (9 1/16) Center of the lens Bottom Unit: mm (inches) 142 (5 19/32) 142 (5 19/32) 81.5 81.5 (3 7/32) (3 7/32) 326 (12 27/32) Front of the cabinet 79.7 (3 1/8) 150.6 (5 15/16) 147.7 (5 13/16) 425.8 (16 3/4) 15.7 (5/8) 496 (19 17/32) The distance between the front of the lens and the front of the cabinet Unit: mm (inches) 41.9 (1 21/32) Front of the lens Front of the cabinet 51 Attaching the PSS-H10 projector suspension support Front view Unit: mm (inches) 150 (5 29/32) 75 (2 15/16) 128 (5 1/32) Ceiling 175 (6 7/8) Center of the supporting pole 8 (5/16) The bottom surface of the mount bracket Center of the lens Side view Unit: mm (inches) 218.3 (8 19/32) 130 (5 1/8) 45 (1 25/32) Front of the cabinet 263.3 (10 3/8) 496 (19 17/32) 52 Top view Unit: mm (inches) 215.4 (8 15/32) 130 (5 1/8) Front of the cabinet Upper ceiling mount bracket 260.4 (10 1/4) Center of the supporting pole (The center of the supporting pole is different from that of the unit.) Holes for the ceiling mount Use the screws with a length of 5.3 mm (7/32 inches, minimum) to 7.0 mm (9/32 inches, maximum) for the ceiling mount. Recommended tightening torque (tension when turning a screw towards the direction of rotation): 1.4 ± 0.2 N-m The minimum length of screw Insert nut (M5) The maximum length of screw Screw hole Unit 53 Sony Corporation
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Print high-res Page Mode : UseOutlines XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2017:09:18 15:54:22Z Creator Tool : FrameMaker 7.1 Modify Date : 2017:09:18 16:01:43+08:00 Metadata Date : 2017:09:18 16:01:43+08:00 Format : application/pdf Creator : Sony Corporation Title : VPL-VW760ES/VW885ES Document ID : uuid:a963f5b8-03a2-447f-9e63-b4a9fc95c5bf Instance ID : uuid:43541e67-010f-4aff-b357-bcb07bf6c165 Page Count : 54 Author : Sony CorporationEXIF Metadata provided by EXIF.tools