SOUNDMAX ELECTRONICS CW8761 BT MODULE User Manual

Soundmax Electronics Limited BT MODULE

User Manual

BLUE TOOTH 4.0 1 CW8761 H.W.Data Sheet
BLUE TOOTH 4.0 2 Revision 18-11-2016 Version 1.0 16-12-2016 Version 1.1 BOM added, Operating Temperature correction
BLUE TOOTH 4.0 3 Table of Content 1 General Descriptions……………………………………………….……..4 2 Block Diagram…….……………………………………………….……..4 3 Schematic drawing……….……………………………………………..5-8 4 Bill of material…………………………………………………………….9 5 Electrical Specifications……………………………………………..........10 6 Test platform………………………………………………………………11
BLUE TOOTH 4.0 4 1 General Descriptions Features ﹒ REALTEK chip set RTL8761 ﹒ BLUETOOTH v4.0 mode requirement. ﹒ Support of enhanced audio applications ﹒ Small and easy to integrate. ﹒ ﹒ ﹒ ﹒ ﹒ ﹒ ﹒ ﹒ ﹒ ﹒ ﹒ ﹒ 2 Block Diagram
BLUE TOOTH 4.0 7
BLUE TOOTH 4.0 8
BLUE TOOTH 4.0 9
BLUE TOOTH 4.0 10 PIN ASSIGMENT PIN Name Type Description 1 GND -- GROUND 2 I/O I N.C. 3 BUART TXD 0 UART TX OUT 4 BUART RXD I UART RX IN 5 BUART RTS I UART REQUEST TO SEND 6 PCM SYNC O PCM SYNC OUT 7 PCM CLK O PCM CLOCK OUT 8 PCM MOSI O PCM DATA OUT 9 PCM MISO I PCM DATA IN 10 BT3V3 -- 3.3v DC IN 11 BT_LDO_EN I LDO ENABLE 12 GND -- GROUND 13 GND -- GROUND 14 BT O AUDIO L 15 BT R O AUDIO R 16 GND -- GROUND 17 I/O I 18 USB D- I USB UPGRADE 19 USB D+ I USB UPGRADE 20 MIC IN I AUDIO INPUT
BLUE TOOTH 4.0 11 4 Electrical Specifications 4.1. Absolute Maximum Rating Item Symbol Rating Unit Power supply voltage (logic) VDD -0.5 to 4.0 V Input voltage Vin -0.5 to VDD+0.5 Power dissipation( Ta=70C ) Pd 200 mW Storage Temperature Tstg -30 to 85 ℃ Operating Temperature Topr -20 to 70 ℃ 4.2. Recommended Operating Condition Item Symbol Min Typ. Max Unit Power supply voltage VDD 2.8 - 3.6 V Input voltage Vin 0 - VDD V Operating temperature Topr -20 - 70 ℃ 4.3. Electrical Characteristics Symbol Parameter Condition Min. Typ. Max. Unit VDD Supply voltage 2.8 - 3.6 V VIH Input high voltage 1.6V - - V VIL Input low voltage - - 1.4V V RPU Pull-up resistance Vin = 0V 100K - - Ohm RPD Pull-down resistance Vin = VDD 100K - - Ohm
BLUE TOOTH 4.0 12 5 Test platform: Interface board:
BLUE TOOTH 4.0 13
BLUE TOOTH 4.0 14
BLUE TOOTH 4.0 15
BLUE TOOTH 4.0 16CW8761 BT4.0 蓝牙模组 : PIN NAME TYPE DESCRIPTION 1 GROUND DIGITAL CROUND 2 GROUND DIGITAL CROUND 3 PCM CLK I/O N.C. (NO CONNECTION) 4 PCM SYNC I/O N.C. (NO CONNECTION) 5 MIC-IN MICROPHONE INPUT 6 BT_LDO_EN ACTIVATE AT LOW LEVEL 7 BT 3V3 DC POWER 3v3 IN 8 BT 3V3 DC POWER 3v3 IN 9 PCM MOSI I/O N.C. (NO CONNECTION) 10 PCM MISO I/O N.C. (NO CONNECTION) 11 B/D+ USB D+ (FIRMWARE UPDATE) 12 B/D- USB D- (FIRMWARE UPDATE) 13 B UART RTS I/O N.C. (NO CONNECTION) 14 B UART RX DATA PORT BT MODULE DATA INPUT 15 B UART TX DATA PORT BT MODULE DATA OUTPUT 16 32K_CLK I/O N.C. (NO CONNECTION) 17 GROUND AUDIO CROUND 18 GROUND AUDIO CROUND 19 BT-R AUDIO R OUTPUT 20 BT-L AUDIO L OUTPUT
BLUE TOOTH 4.0 17
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AB7S-CW8761 Or Contains FCC ID: 2AB7S-CW8761”When the module is installed inside another device, the user manual of the host must contain below warning statements;1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C : 15.247 and 15.209 requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 requirement，then the host can be sold legally.IC STATEMENTThis device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes :( 1 ) Ce dispositif ne peut causer d'interférences ; et( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 11888A-CW8761”when the module is installed inside another device, the user manual of this device must contain below warning statements;1. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.2. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes :( 1 ) Ce dispositif ne peut causer d'interférences ; et( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product

Navigation menu